Fritless capillary electrochromatography

The preparation of packed capillaries with stable frits of good quality can be a hurdle to obtain efficient separations in capillary electrochromatography (CEC). Especially with particles smaller than 3 microm, frit preparation is cumbersome. Highly efficient separations using packed capillaries without frits are presented. Under appropriate CEC conditions the particles were retained by electrophoretic attraction towards the anode by a tapered capillary inlet, without the need of a frit at the outlet end. Such fritless capillaries, packed with 1.5 microm nonporous reversed-phase particles, allowed separations with efficiencies of more than 500,000 plates/m. Once the capillaries were conditioned properly, more than 100 separations could be performed with good repeatability. With respect to separation efficiency, fritless capillaries packed with 3 microm particles were comparable with standard CEC capillaries with frits. Examples of separations of steroids, a pesticide and its by-products, and cardiac glycosides under various CEC conditions are shown.     

Polyether ether ketone encased monolith frits made of polyether ether ketone tubing with a 0.25 mm opening resulting in an improved separation performance in liquid chromatography

Tiny polyether ether ketone encased monolith frits have been prepared by modified catalytic sulfonation of the inner surface of polyether ether tubing (1.6 mm od, 0.25 mm id) followed by modified formation of organic monolith and cutting of the tubing into slices. The frit was placed below the central hole of the column outlet union and supported by a combination of a silica capillary (0.365 mm od, 0.05 mm id) and a polyether ether ketone sleeve (1.6 mm od, 0.38 mm id) tightened with a nut and a ferrule when the column was packed to prevent sinking of the frit element into the union hole (0.25 mm opening) otherwise. The column packed this way with the frits investigated in this study has shown better separation performance owing to the reduced frit volume in comparison to the column packed with a commercial stainless‐steel screen frit. This study establishes the strategy of disposable microcolumns in which cheap disposable frits are used whenever the column is re‐packed to yield columns of even better chromatographic performance than the columns with commercial frits.     

Magnetically immobilized frits for the preparation of packed columns used in capillary electrochromatography

Fabrication of porous frits to retain stationary phases is a critical issue in column preparation for capillary electrochromatography (CEC). In this work, porous frits were prepared by applying an external magnetic field to magnetically responsive particles placed inside a fused-silica capillary. Three batches of uniform magnetite spheres with particle diameters of 0.3, 0.4, and 0.6 μm and saturation magnetization values of 73.03, 74.41, and 77.83 emu/g, respectively, were used as frit particles and octadecyl- and phenyl-bonded silica gels were packed successfully into frit-containing capillaries. The performance of the resulting magnetically immobilized frits and packed columns was evaluated. The electroosmotic mobilities in capillaries containing outlet frit only were found to be reduced by 2–4% whereas the plate heights of an unretained marker increased by 30–50% as compared to those in open capillaries. These variations are believed to be associated with the inhomogeneities of the packed structure of the frits. The magnetically immobilized frits showed adequate mechanical strength to withstand the flow drag force, allowing separation in capillaries packed with 5-μm stationary phases up to 10–15 cm, thus rendering column efficiency and reproducibility comparable with those obtained with sintered frits. Taken together, retaining frits made of uniform magnetite particles serves as a viable alternative to sintered frits for column preparation, which offers several distinct advantages such as ease of preparation, improved durability as compared to sintered frits where the removal of the polyimide coating makes the packed column susceptible to breakage, and use of large-bore capillaries for semipreparative separations.     

Disposable microcolumns with welded metal frits

This study reports the preparation of disposable microcolumns with welded metal frits for the first time. First, the bottom of glass‐lined stainless‐steel tubing of 30 cm length, 1.6 mm od, and 0.5 mm id was welded with a stainless‐steel screen frit of 1.6 mm diameter. A micro‐welding machine was used for this. Next, the column was connected to a slurry packer and packed with porous silica particles. Then, the inlet of the column was carefully welded with another frit. The column was tested for separation of a test mix composed of phenol, 2‐nitrophenol, acetophenone, aceanilide, and benzamide. Another column of the same physical dimension was also prepared with frits that were not welded to the column. The chromatographic performances of the two groups of columns (welded frits versus non‐welded frits) were examined. The columns of welded frits showed ca. 18% better separation efficiency (number of theoretical plates) than those of non‐welded frits.     

New method for sintering silica frits for capillary microcolumns

One of the main steps in the manufacture of robust and efficient packed capillary microcolumns for electro- and capillary chromatography is the generation of porous devices to retain the packed beds. Frits based on sintered silica particles have been found to give the best results in terms of mechanical resistance and efficiency. The conventional procedure to produce these kinds of frits consists in a radial heating of the packed material with either a flame or an electrical resistance, but the frits thus obtained have many drawbacks as a result of the procedure rather than the silica per se as the base material. In the present work we investigated a new approach to produce silica-based retaining devices involving the frontal exposure of a short silica-particle bed packed at the end of a capillary tube. The capillary is radially insulated and frontally exposed to the heat of a muffle oven, generating a transfer of heat that is not radial but rather throughout the capillary axis. This procedure resulted in substantial advantages: an improved radial homogeneity, a protection of the external polyimide, and a generation of extremely short (400–600 μm) frits that were highly permeable and avoided bubble formation.     

Fabrication of monolithic frits and columns for chip-based multidimensional separation devices

In this work, devices for two-dimensional separations are considered. The device contains a flow distributor, a first-dimension channel, and 17 second-dimension outlets. In the design, all connections between the first-dimension channel, the flow distributor, and the second-dimension outlets were tapered, with a minimal diameter of 20 μm. The use of photo-masking is explored for the fabrication of monolithic frits in all tapered connections. Monolithic frits with optimized permeability and length were successfully fabricated in all 33 tapered channels through light-induced polymerization, photo-masking, and selective exposure. The efficacy of the monolithic frits was demonstrated by creating a packed bed of 15-μm particles, confined within the first-dimension channel. The outlet of the first-dimension channel was successfully connected to a mass spectrometer. Effective flow confinement was demonstrated with a reversed-phase separation of a mixture of five standard peptides.     

Novel approach for fritless capillary electrochromatography

At present, the main limitation for the further adoption of capillary electrochromatography (CEC) in the (routine) laboratory is caused by the lack of reproducible and stable columns. The main source of column instability is concentrated in the frits needed to retain the packed bed inside the CEC capillary. The sintering process used to prepare the frits can be rather problematic and irreproducible, particularly for small stationary phase particles and wide column diameters. Since the (surface) composition of the frits is different from the bulk stationary phase packing, different electroosmotic flow (EOF) velocities are generated. This effect is assumed to be primarily responsible for rapid column destruction. In this contribution, a novel approach for the preparation of fritless CEC capillaries is presented and evaluated. Using 5 microm Hypersil ODS particles, separation efficiencies in the range of 130,000-200,000 plates/m were obtained. In a 100 microm inner diameter packed column, electrical currents up to 50 microA could be tolerated without negative effects such as bubble formation. The prepared CEC columns were found to be stable and could easily be operated continuously for several days without column damage. An additional advantage of the proposed tapering approach is that application of pressure on the in- and outlet vial during separation was not required to prevent bubble formation.     

Capillary electrochromatography without external pressure assistance. Use of packed columns with a monolithic inlet frit

A fused silica capillary column was packed with RP(18) silica stationary phase entrapping the particles between two frits obtained by two different procedures. The inlet frit consisted of a short organic polymer made via a thermopolymerization process while the outlet frit was prepared by sintering the octadecylsilica (ODS) material. The packed column was employed in capillary electrochromatography (CEC) experiments for the separation of three selected test compounds. Retention time and separation efficiency were evaluated. Results were compared with those ones obtained with a packed capillary containing the same stationary phase entrapped between two sinterized frits. The novel packed column exhibited comparable separation efficiency and resolution with the traditional one. However, it allowed experiments without pressure support during the runs with no bubble formation.     

Micro-high-performance liquid chromatography platform for the depletion of high-abundance proteins and subsequent on-line concentration/capturing of medium and low-abundance proteins from serum. Application to profiling of protein expression in healthy and osteoarthritis sera by 2-D gel electrophoresis

In this investigation, an integrated microcolumn-based fluidic platform for the simultaneous depletion of high-abundance proteins and the subsequent on-line concentration/capturing of medium- and low-abundance proteins from human serum has been introduced. The platform consists of on-line coupling of tandem affinity micorcolumns to an RP microcolumn to achieve first the depletion of high-abundance proteins by the tandem affinity microcolumns followed by the concentration and capturing of medium- and low-abundance proteins by the RP microcolumn. The tandem affinity microcolumns are based on macroporous monoliths characterized by their relatively high permeability in pressure-driven flow while the RP microcolumn is packed with polymeric particles with an average particle diameter of 20 microm giving rise to a very little back pressure, thus allowing fast flow velocity across the coupled columns format and consequently short processing time of serum samples prior to analysis by 2-DE. The microcolumn-based fluidic platform was applied to serum samples from osteoarthritis (OA) donors before and after soy protein (SP) supplementation, and from healthy donors, and the resulting depleted serum samples from high-abundance proteins were profiled for protein expression by 2-DE. In general, the protein expression was lower in serum of the same OA patient after soy treatment than before soy treatment. Several proteins were down-regulated after soy treatment with transthyretin being the most affected by the SP supplementation. In addition, with respect to serum from healthy donors, the sera from OA patients showed difference in proteins expression.     

A continuous DC-insulator dielectrophoretic sorter of microparticles

A lab-on-a-chip device is described for continuous sorting of fluorescent polystyrene microparticles utilizing direct current insulating dielectrophoresis (DC-iDEP) at lower voltages than previously reported. Particles were sorted by combining electrokinetics and dielectrophoresis in a 250 μm wide PDMS microchannel containing a rectangular insulating obstacle and four outlet channels. The DC-iDEP particle flow behaviors were investigated with 3.18, 6.20 and 10 μm fluorescent polystyrene particles which experience negative DEP forces depending on particle size, DC electric field magnitude and medium conductivity. Due to negative DEP effects, particles are deflected into different outlet streams as they pass the region of high electric field density around the obstacle. Particles suspended in dextrose added phosphate buffer saline (PBS) at conductivities ranging from 0.50 to 8.50 mS/cm at pH 7.0 were compared at 6.85 and 17.1 V/cm. Simulations of electrokinetic and dielectrophoretic forces were conducted with COMSOL Multiphysics^® to predict particle pathlines. Experimental and simulation results show the effect of medium and voltage operating conditions on particle sorting. Further, smaller particles experience smaller iDEP forces and are more susceptible to competing nonlinear electrostatic effects, whereas larger particles experience greater iDEP forces and prefer channels 1 and 2. This work demonstrates that 6.20 and 10 μm particles can be independently sorted into specific outlet streams by tuning medium conductivity even at low operating voltages. This work is an essential step forward in employing DC-iDEP for multiparticle sorting in a continuous flow, multiple outlet lab-on-a-chip device.     

加芯毛细管填充柱的理论研究

 从速率方程和柱压降两个方面对加芯毛细管填充柱的柱效和渗透性进行了探讨，并详细讨论了柱直径、芯直径、芯根数和柱压降的关系。综合考虑柱压降、板高和拉制柱子时颗粒在柱内的镶嵌状况可知最佳柱型是３芯的毛细管填充柱。     

Photopolymerized sol-gel frits for packed columns in capillary electrochromatography

Porous sol-gel frits are fabricated in a capillary column by filling it with a solution of 3-(trimethoxysilyl)propyl methacrylate, hydrochloric acid, water, toluene (porogen), and a photoinitiator (Irgacure 1800) and exposing it to UV light at 365 nm for 5 min. The separation column (30 cm x 75 microm I.D.) contains between the inlet and outlet frits a 15-cm packed segment filled with 5-microm silica particles modified with the chiral compound (S)-N-3,5-dinitrobenzoyl-1-naphthylglycine. A detection window (1 mm long) is placed immediately after the outlet frit. To demonstrate the performance of this chiral separation column, mixtures of 16 different amino acids (three of which are not naturally occurring) derivatized with the fluorogenic reagent 4-fluoro-7-nitro-2,1,3-benzoxadiazole were separated by capillary chromatography. The enantiomeric separation of the column results in a resolution ranging from 1.21 to 8.29, and a plate height ranging from 8.7 to 39 microm.     

气溶胶粒子通过填充柱的保留时间分布测定

采用亚微米单分散聚苯乙烯球形硬气溶胶粒子和脉冲进样技术,测定了气溶胶粒子通过无规则石英砂填充柱的保留时间分布,从保留时间分布曲线得到了气溶胶粒子在填充柱中的平均保留时间和穿透率.研究了平均保留时间和穿透率与流体流速、填充柱的长度、填料粒度和气溶胶粒子大小之间的关系.研究发现,流速越大,保留时间分布曲线越尖锐,流速越小,保留时间分布曲线越平坦;气溶胶粒子的穿透率随着柱长的增加而降低,随流速、气溶胶粒子粒径和石英砂颗粒大小的减小而减小;平均保留时间随柱长增加而增大,随流速增大而减小,随气溶胶粒子粒径减小而减小,而与石英砂颗粒大小几乎无关.     

Optimization of post-column reactor radius in capillary high performance liquid chromatography Effect of chromatographic column diameter and particle diameter

A post-column reactor consisting of a simple open tube (Capillary Taylor Reactor) affects the performance of a capillary LC in two ways: stealing pressure from the column and adding band spreading. The former is a problem for very small radius reactors, while the latter shows itself for large reactor diameters. We derived an equation that defines the observed number of theoretical plates (N(obs)) taking into account the two effects stated above. Making some assumptions and asserting certain conditions led to a final equation with a limited number of variables, namely chromatographic column radius, reactor radius and chromatographic particle diameter. The assumptions and conditions are that the van Deemter equation applies, the mass transfer limitation is for intraparticle diffusion in spherical particles, the velocity is at the optimum, the analyte's retention factor, k', is zero, the post-column reactor is only long enough to allow complete mixing of reagents and analytes and the maximum operating pressure of the pumping system is used. Optimal ranges of the reactor radius (a(r)) are obtained by comparing the number of observed theoretical plates (and theoretical plates per time) with and without a reactor. Results show that the acceptable reactor radii depend on column diameter, particle diameter, and maximum available pressure. Optimal ranges of a(r) become narrower as column diameter increases, particle diameter decreases or the maximum pressure is decreased. When the available pressure is 4000 psi, a Capillary Taylor Reactor with 12 microm radius is suitable for all columns smaller than 150 microm (radius) packed with 2-5 microm particles. For 1 microm packing particles, only columns smaller than 42.5 microm (radius) can be used and the reactor radius needs to be 5 microm.     

Adhesion as an interplay between particle size and surface roughness

Surface roughness plays an important role in the adhesion of small particles. In this paper we have investigated adhesion as a geometrical effect taking into account both the particle size and the size of the surface features. Adhesion is studied using blunt model particles on surfaces up to 10 nm root-mean-square (RMS) roughness. Measurements with particles both smaller and larger than surface features are presented. Results indicate different behavior in these areas. Adhesion of particles smaller than or similar in size to the asperities depend mainly on the size and shape of the asperities and only weakly on the size of the particle. For large particles also the particle size has a significant effect on the adhesion. A new model, which takes the relative size of particles and asperities into account, is also derived and compared to the experimental data. The proposed model predicts adhesion well over a wide range of particle/asperity length scales.     

1.1 μm superficially porous particles for liquid chromatography. Part I: synthesis and particle structure characterization

Superficially porous particles are characterized by a non-porous particle core surrounded by a thin porous layer. Superficially porous particles have been shown to have chromatographic advantages over traditional totally porous particles by reducing the resistance to mass transfer and the eddy diffusion contributions to the theoretical plate height, particularly for biomolecule separations. Currently, 1.7 μm superficially porous particles are commercially available, but a further decrease in the particle diameter and reduction in the porous layer thickness has the potential to further improve the efficiency of the column packing material. In this study, the synthesis of smaller diameter superficially porous particles was investigated. As the particle diameter was decreased, however, synthesis parameters previously reported were rendered unsuitable due to particle agglomeration, non-uniform coating, and porous layer disintegration. Parameters such as colloidal silica size, drying process, and sintering temperature were investigated to improve the structural characteristics of smaller diameter superficially porous particles. Reported is a synthetic route for production of 1.1 μm superficially porous particles having a 0.1 μm porous layer. Based on the revised method, the particles produced have a surface area, pore diameter, and particle size distribution RSD of 52 m²/g, 71 Å, and 2.2%, respectively.     

The Development of Reversed‐Phase Capillary Electrochromatography for the Separation of Steroids

This paper describes the preparation and optimization of packed capillary columns for reversed‐phase separation of steroids with CEC. The fabrication of on‐column frits is considered to be the most important step for obtaining a reproducible packed column for CEC separation. Porous silicate frits were generated in a fused‐silica capillary by heating the silica gel/sodium hydroxide solutions electrically. The optimized conditions involve silica gel (10.8%), sodium hydroxide (5.8%), and heating time (5 sec) with heating voltage (5V) for obtaining a 100‐μ end‐frit that can withstand pressure over 6000 psi. A HPLC pump was utilized to pack the 5‐μm ODS particle slurry into the capillary column. The ODS packed capillaries were then utilized for the separation of four anabolic cholesterols with a capillary electrophoresis system without pressurization of the column. The reproducibility of the packed columns was evaluated by measuring the relative standard deviations of four steroids. The relative standard deviations of migration time for column‐to‐column, day‐to‐day, and run‐to‐run are less than 7%, 2%, and 1% for four steroids, respectively.     

Visualization of sample introduction in liquid chromatography columns. The effect of the frit diameter.

A previously developed on-column detection technique using 35 mm SLR cameras [J. Chromatogr. A 826 (1998) 1] was employed to visualize colored sample bands as they elute through frits of differing diameter. Head fittings containing a 4.0 mm frit and a 15.9 mm frit were mounted in a 17 mm I.D. glass column packed with C18 silica with an average particle size of 21 microns. A carbon tetrachloride mobile phase of matching refractive index to that of the silica provides clarity along the column diameter during band migration. The photographs of the migrating sample zones were scanned and analyzed with appropriate imaging software. The smallest diameter frit induced severely parabolic sample distributions at the column inlet compared to the larger frit. Local axial dispersion coefficient values, expressed as local reduced plate height, were calculated as well as local zone velocities at the column inlet. The results demonstrate clearly the need to match the diameter of the inlet frit to the I.D. of the column so as to avoid the initial onset of zone broadening due to the frit.     

A Simple Method to Prepare On‐Capillary Frits for Micro‐Column Separation

Sintering stainless steel powders was initially used to prepare the inlet frit in fused silica capillaries. The use of such inlet frits and outlet frits sintered by the stationary phase itself in the capillary to retain C₁₈ particles was demonstrated to withstand the long exposure, up to a high pressure of 60 MPa, for packing and the prepare column was stable and robust enough to do the continuous chromatographic operations. Characterization of the inlet and outlet frits by scanning electron micrography showed the fused metal particles formed a porous network in the capillary inlet and the homogenous separation beddings were obtained by slurry packing.     

Dielectrophoretic manipulation of particle mixtures employing asymmetric insulating posts

A novel scheme for particle separation with insulator‐based dielectrophoresis (iDEP) was developed. This technique offers the capability for an inverted order in particle elution, where larger particles leave the system before smaller particles. Asymmetrically shaped insulating posts, coupled with direct current (DC) biased low‐frequency alternating current (AC) electric potentials, were used to successfully separate a mixture of 500 nm and 1 μm polystyrene particles (size difference of 0.5 μm in diameter). In this separation, the 1 μm particles were eluted first, demonstrating the discriminatory potential of this methodology. To extend this technique to biological samples, a mixture containing Saccharomyces cerevisiae cells (6.3 μm) and 2 μm polystyrene particles was also separated, with the cells being eluted first. The asymmetric posts featured a shorter sharp half and a longer blunt half; this produced an asymmetry in the forces exerted on the particles. The negative DC offset produced a net displacement of the smaller particles toward the upstream direction, while the post asymmetry produced a net displacement of the larger particles toward the downstream direction. This new iDEP approach provides a setup where larger particles are quickly concentrated at the outlet of the post array and can be released first when in a mixture with smaller particles. This new scheme offers an extra set of parameters (alternating current amplitude, DC offset, post asymmetry, and shape) that can be manipulated to obtain a desired separation. This asymmetric post iDEP technique has potential for separations where it is important to quickly elute and enrich larger and more fragile cells in biological samples.