Preparation and bactericide activity of gallic acid stabilized gold nanoparticles

In this work, gold nanoparticles with three different sizes (13.7, 39.4, and 76.7 nm) were prepared using a simple aqueous method with gallic acid as the reducing and stabilizing agent, the different sizes were obtained varying some experimental parameters as the pH of the reaction and the amount of the gallic acid. The prepared nanoparticles were characterized using X-ray diffraction, transmission electron microscopy, dynamic light scattering, and UV–Vis spectroscopy. Samples were identified as elemental gold and present spherical morphology, a narrow size distribution and good stabilization according to TEM and DLS results. The antibacterial activity of this gallic acid stabilized gold nanoparticles against S. mutans (the etiologic agent of dental caries) was assessed using a microdilution method obtaining a minimum inhibitory concentration of 12.31, 12.31, and 49.25 μg/mL for 13.7, 39.4, and 76.7 nm gold nanoparticles, respectively. The antibacterial assay showed that gold nanoparticles prepared in this work present a bactericide activity by a synergistic action with gallic acid. The MIC found for this nanoparticles are much lower than those reported for mixtures of gold nanoparticles and antibiotics.     

Green synthesis of silver and gold nanoparticles using Rosa damascena and its primary application in electrochemistry

Biosynthesis and characterizations of nanoparticles have become an important branch of nanotechnology. In this paper, green synthesis of gold nanoparticles (AuNPs) and silver nanoparticles (AgNPs) using the flower extract of Rosa damascena as a reducing and stabilizing agent, has been discussed. This approach is simple, cost-effective and stable for a long time, reproducible at room temperature and in an eco-friendly manner to obtain a self-assembly of AuNPs and AgNPs. The resulting nanoparticles are characterized using UV–vis, TEM, XRD and FT-IR spectroscopic techniques. A modified glassy carbon electrode using AuNPs (AuNPs/GCE) was investigated by means of cyclic voltammetry in a solution of 0.1 M KCl and 5.0×10⁻³ M [Fe(CN)₆]^3−/4−. The results show that electronic transmission rate between the modified electrode and [Fe(CN)₆]^3−/4− increased.     

Ultrasound-assisted fabrication of metal nano-porous shells across polymer beads and their catalytic activity for reduction of 4-nitrophenol

Metal nano-porous architectures are a novel class of nanomaterials which has been applied in the fields of catalysis, sensing and gas storage because of their high surface-to-volume ratio, high mechanical strength and long-range ordered architectures. A commonly-used synthetic strategies to achieve architectures with high precision and diverse porosity design is the seed-and-growth method. In this work, using a dual-frequency sequential sonication approach, we have demonstrated a sonochemical-assisted one-pot seeding with a successive shell growth synthetic strategy for mesoporous metal deposition via a gold (Au) nanoparticle and poly(styrene) beads system. A uniform coating of gold nanoparticle seeds with dense surface coverage was formed by first employing 300 kHz ultrasound irradiation while the nano-porous shell growth was then performed under 1 MHz ultrasonic frequency. The precise control over the process conditions and parameters allowed for the design of well-defined shell thicknesses and surface roughness and area. The catalytic property of the MNMs was evaluated for the degradation of 4-nitrophenol and a high catalytic activity was achieved for the most porous gold structures, suggesting synergistic effects between the architecture of the nanomaterials and their surface reactivity.     

Green synthesis and characterization of gold nanoparticles using extract of anti-tumor potent Crocus sativus

In the present study, we have explored anti-tumor potent Crocus sativus (saffron) as a reducing agent for one pot size controlled green synthesis of gold nanoparticles (AuNps) at ambient conditions. The nanoparticles were characterized using UV–vis, scanning electron microscope (SEM), high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD) and FTIR analysis. The prepared AuNPs showed surface Plasmon resonance centered at 549 nm with average particle size of 15±5 nm. Stable, spherical and triangular crystalline AuNPs with well-defined dimensions were synthesized using anti-tumor potent Crocus sativus (saffron). Crystalline nature of the nanoparticles is confirmed from the HR-TEM, SAED and SEM images, and XRD patterns. From the FTIR spectra it is found that the biomolecules are responsible for capping in gold nanoparticles.     

Biosynthesis of gold nanoparticles using Capsicum annuum var. grossum pulp extract and its catalytic activity

Biological synthesis approach has been regarded as a green, eco-friendly and cost effective method for nanoparticles preparation without any toxic solvents and hazardous bi-products during the process. This present study reported a facile and rapid biosynthesis method for gold nanoparticles (GNPs) from Capsicum annuum var. grossum pulp extract in a single-pot process. The aqueous pulp extract was used as biotic reducing agent for gold nanoparticle growing. Various shapes (triangle, hexagonal, and quasi-spherical shapes) were observed within range of 6–37 nm. The UV–Vis spectra showed surface plasmon resonance (SPR) peak for the formed GNPs at 560 nm after 10 min incubation at room temperature. The possible influences of extract amount, gold ion concentration, incubation time, reaction temperature and solution pH were evaluated to obtain the optimized synthesis conditions. The effects of the experimental factors on NPs synthesis process were also discussed. The produced gold nanoparticles were characterized by transform electron microscopy (TEM), X-ray diffraction (XRD), energy dispersive X-ray (EDS) and Fourier Transform infrared spectroscopy (FTIR). The results demonstrated that the as-obtained GNPs were well dispersed and stable with good catalytic activity. Biomolecules in the aqueous extract were responsible for the capping and stabilization of GNPs.     

Mono and bimetallic nanoparticles of gold,silver and palladium-catalyzed NADH oxidation-coupled reduction of Eosin-Y

Abstract  

Mono metallic (Au, Ag, Pd) and bimetallic (Au–Ag, Ag–Pd, Au–Pd) with 1:1 mol stoichiometry, nanoparticles are synthesized using one-pot, temperature controlled chemical method using cetyltrimethylammonium bromide (CTAB) as the capping agent. The particle sizes (Au = 5.6, Ag = 5.0, Pd = 6.0, Au–Ag = 9.2, Ag–Pd = 9.6, Au–Pd = 9.4 nm) are characterized by UV–Vis, HRTEM, and XRD measurements, respectively. CTAB bindings onto mono and bimetallic nanoparticles are analyzed by FTIR spectra. The catalytic activities of mono and bimetallic nanoparticles are tested on the reaction between NADH oxidation and Eosin-Y reduction. The effects of base, pH, ionic strength, nature of mono and bimetallic catalysts are studied and the reaction conditions are optimized. Bimetallic nanoparticles exhibited better catalysis than the mono metallic nanoparticles, which may be due to the electronic effects of the core to shell metal atoms.     

Ultrasound-assisted green synthesis of gold nanoparticles using citrus peel extract and their enhanced anti-inflammatory activity

Ultrasound and plant extract are two green approaches that have been used to synthesize gold nanoparticles (AuNPs); however, how the combination of ultrasound and citrus peel extract (CPE) affects the structure characteristics and the bioactivity of AuNPs remains unknown. Here we investigated the effects of ultrasound conditions on the particle size, stability, yield, phenolic encapsulation efficacy, and the anti-inflammatory activity of AuNPs. The results showed that temperature was positively correlated to the particle size and the anti-inflammatory activity of synthesized AuNPs. Increasing the power intensity significantly decreased the particle size, while increased the change of total phenolic content (ΔTPC) in the reaction mixture. The increase of ΔTPC caused the enhanced anti-inflammatory activity of AuNPs. The AuNPs synthesized with or without ultrasound treatment were characterized using UV–Vis, DLS, SEM, TEM, EDS, XRD, and FT-IR. The result verified the formation of negatively charged, spherical, stable, and monodispersed AuNPs. AuNPs synthesized with ultrasound (AuNPs-U) has smaller particle size (13.65 nm vs 16.80 nm), greater yield and anti-inflammatory activity (IC₅₀, 82.91 vs 157.71 μg/mL) than its non-ultrasound counterpart (AuNPs-NU). HPLC analysis showed that hesperidin was the key reductant for the synthesis of AuNPs. AuNPs-U also inhibited the mRNA and protein expression of iNOS and COX-2 in the LPS-induced Raw 264.7 cells. Our research elucidates the relationship between the reaction conditions and the structure characteristics and the anti-inflammatory activity of AuNPs synthesized using CPE with the help of ultrasound, thereafter, provides a feasible and economic way to synthesize AuNPs that can be used to ameliorate inflammation.     

Ultrasound-assisted synthesis of metal organic framework for the photocatalytic reduction of 4-nitrophenol under direct sunlight

In this study, the metal organic framework MOF [Zn(BDC)(DMF)] crystal was synthesized via ultrasonic irradiation and solvothermal method. The synthesized MOF [Zn(BDC)(DMF)] crystal was characterized by PXRD, FTIR, FESEM-EDX, TGA, UV-DRS and BET. The catalytic activity of MOF [Zn(BDC)(DMF)] was investigated by 4-nitrophenol (4-NP) degradation under direct sunlight irradiation. The influence of various degradation parameters such as initial 4-NP concentration, dosage, pH and H₂O₂ concentration were investigated. The results indicated that the synthesized MOF [Zn(BDC)(DMF)] exhibited strong photocatalytic activity in the presence of NaBH₄ under sunlight irradiation and the reduction of 4-NP to 4-aminophenol (4-AP) completed within 10 min. The study provides the synthesized MOF [Zn(BDC)(DMF)] crystal can be used as a high performance catalyst for the treatment of dyes in wastewater.     

Green synthesis of Au nanoparticles using potato extract: stability and growth mechanism

Airborne particle release during the spray application of coatings was analyzed in the nanometre and micrometre size range. In order to represent realistic conditions of domestic and handcraft use, the spray application was performed using two types of commercial propellant spray cans and a manual gravity spray gun. Four different types of coatings doped with three kinds of metal-oxide tracer nanoparticle additives (TNPA) were analyzed. Depending on the used coating and the kind of spray unit, particulate release numbers between 5 × 10⁸ and 3 × 10¹⁰ particles per gram ejection mass were determined in the dried spray aerosols. The nanoparticulate fraction amounted values between 10 and 60 no%. The comparison between nanoparticle-doped coatings with non-doped ones showed no TNPA-attributed differences in both the macroscopic spray process characteristics and the particle release numbers. SEM, TEM and EDX-analyzes showed that the spray aerosols were composed of particles made up solely from matrix material and sheathed pigments, fillers and TNPAs. Isolated ZnO- or Fe₂O₃-TNPAs could not be observed.     

Amine-capped gold nanoparticles: reaction steps during the synthesis and the influence of the ligand on the particle size

Alkylamine-capped gold nanoparticles were synthesised using the Leff method. In order to investigate the influence on the complexes formed during the synthesis and the final size of the protected nanoparticles the chain length of the stabilizing ligands varied. Phase transfer and amine complex formation were studied in solution with X-ray absorption spectroscopy. The phase transfer complexes retain the quadratic planar conformation whilst all alkyl amines form a linear coordinated gold(I) complex. After reduction, the particles were characterised in solution with EXFAS, UV–Vis spectroscopy, and compared to TEM measurements. The size of the particles was determined from the coordination number of the first gold shell. The position of the UV–Vis plasmon band and the distance of the first gold shell were used to qualitatively compare the effects of the ligands on the particle size. The size of the particles decreases with increasing chain length.     

Phyllanthin-assisted biosynthesis of silver and gold nanoparticles: a novel biological approach

Abstract  The anisotropic gold and spherical–quasi-spherical silver nanoparticles (NPs) were synthesized by reducing aqueous chloroauric acid (HAuCl₄) and silver nitrate (AgNO₃) solution with the extract of phyllanthin at room temperature. The rate of reduction of HAuCl₄ is greater than the AgNO₃ at constant amount of phyllanthin extract. The size and shape of the NPs can be controlled by varying the concentration of phyllanthin extract and thereby to tune their optical properties in the near-infrared region of the electromagnetic spectrum. The case of low concentration of extract with HAuCl₄ offers slow reduction rate along with the aid of electron-donating group containing extract leads to formation of hexagonal- or triangular-shaped gold NPs. Transmission electron microscopy (TEM) analysis revealed that the shape changes on the gold NPs from hexagonal to spherical particles with increasing initial concentration of phyllanthin extract. The Fourier transform infrared spectroscopy and thermogravimetric analyses reveal that the interaction between NPs and phyllanthin extract. The cyclic voltammograms of silver and gold NPs confirms the conversion of higher oxidation state to zero oxidation state. Graphical abstract  Anisotropic gold and silver nanoparticles were synthesized by a simple procedure using phyllanthin extract as reducing agent. The rate of bioreduction of AgNO₃ is lower than the HAuCl₄ at constant concentration of phyllanthin extract. The required size of the nanoparticles can be prepared by varying the concentration of phyllanthin with AgNO₃ and HAuCl₄.      

Room-temperature synthesis of gold nanoparticles and nanoplates using Shewanella algae cell extract

Biosynthesis of spherical gold nanoparticles and gold nanoplates was achieved at room temperature and pH 2.8 when cell extract from the metal-reducing bacterium Shewanella algae was used as both a reducing and shape-controlling agent. Cell extract, prepared by sonicating a suspension of S. algae cells, was capable of reducing 1 mol/m³ aqueous AuCl₄ ⁻ ions into elemental gold within 10 min when H₂ gas was provided as an electron donor. The time interval lapsed since the beginning of the bioreductive reaction was found to be an important factor in controlling the morphology of biogenic gold nanoparticles. After 1 h, there was a large population of well-dispersed, spherical gold nanoparticles with a mean size of 9.6 nm. Gold nanoplates with an edge length of 100 nm appeared after 6 h, and 60% of the total nanoparticle population was due to gold nanoplates with an edge length of 100–200 nm after 24 h. The yield of gold nanoplates prepared with S. algae extract was four times higher than that prepared with resting cells of S. algae. The resulting biogenic gold nanoparticle suspensions showed a large variation in color, ranging from pale pink to purple due to changes in nanoparticle morphology.     

Effect of temperature on the synthesis of silver nanoparticles with polyethylene glycol: new insights into the reduction mechanism

Polyethylene glycol (PEG) molecules act as a reducing and stabilizing agent in the formation of silver nanoparticles. PEG undergoes thermal oxidative degradation at temperatures over 70 °C in the presence of oxygen. Here, we studied how the temperature and an oxidizing atmosphere could affect the synthesis of silver nanoparticles with PEG. We tested different AgNO₃ concentrations for nanoparticles syntheses using PEG of low molecular weight, at 60 and 100 °C. At the higher temperature, the reducing action of PEG increased and the effect of PEG/Ag⁺ ratio on nanoparticles aggregation changed. These results suggest that different synthesis mechanisms operate at 60 and 100 °C. Thus, at 60 °C the reduction of silver ions can occur through the oxidation of the hydroxyl groups of PEG, as has been previously reported. We propose that the thermal oxidative degradation of PEG at 100 °C increases the number of both, functional groups and molecules that can reduce silver ions and stabilize silver nanoparticles. This degradation process could explain the enhancement of PEG reducing action observed by other authors when they increase the reaction temperature or use a PEG of higher molecular weight     

Stabilization of triangular and heart-shaped plane silver nanoparticles using 2-thiobarbituric acid

The synthesis of silver non-spherical structures like nanotriangles, nanohexagons, and nanodisks, etc., follows a kinetic control that strongly depends on the nature and concentration of the reagents. By using sodium borohydride in a low molar ratio respect to the Ag⁺ source for working under kinetic control, it was possible to obtain different plane nanostructures which in turn could be stabilized by the use of the substituted mercaptopyrimidine 2-thiobarbituric acid. In addition, the use of this thiol allowed the stabilization of an unreported shape that could be an intermediate structure in the shape evolution of nanotriangles through nanodisks. This new particle, with 200–300 nm length and 6 nm height, is named “nanoheart” due to its heart-shaped resemblance.     

Synthesis of graphene oxide sheets decorated by silver nanoparticles in organic phase and their catalytic activity

The graphene oxide(GO) sheets decorated by Ag nanoparticles were prepared using a liquid–liquid two-phase method at the room temperature. The synthesized samples existed in the organic phase and were characterized by X-ray diffraction, transmission electron microscopy, UV–vis spectroscopy and Raman spectra. The results demonstrate that these silver-nanoparticles with diameter of about 10 nm assembled on graphene oxide sheets are flexible and can form stable suspensions in organic phase. Raman signals of graphene oxide sheets are increased by the attached silver nanoparticles, displaying higher surface-enhanced Raman scattering activity. Furthermore, Ag/GO are found to serve as effective catalysts to activate the reduction of 4-nitrophenol (4NP) in the presence of NaBH₄.     

Comparing the interparticle coupling effect on sensitivities of silver and gold nanoparticles

The wavelength shift of surface plasmon resonance peak resulting from the electromagnetic coupling noble metal nanoparticle increases with the increase in the dielectric constant of the medium and the decrease in the interparticle separation distance. In this work, the discrete dipole approximation method was used to calculate the extinction efficiency spectra of the silver–silver and gold–gold nanoparticle pairs. This work shows that the silver coupled-particle system has higher plasmon resonance sensitivity as compared to the gold coupled-particle system. However, the silver coupled-particle system has lower and a faster near-exponential decay of sensitivity enhancement factor than the gold coupled-particle system. Thus, the silver coupled-particle may be more suited for sensing applications as compared to the gold coupled-particle, but the interparticle coupling effect displays more pronounced effect on the gold coupled-particle system as compared to the silver coupled-particle system.     

Silver,gold and the corresponding core shell nanoparticles: synthesis and characterization

Simple strategies for producing silver and gold nanoparticles (AgNP and AuNP) along with the corresponding core shell nanoparticles (Au–Ag and Ag–Au) by reduction of the metal salts AgBF₄ and HAuCl₄ by NaBH₄ in water will be presented. The morphologies of the obtained nanoparticles are determined by the order of addition of reactants. The obtained NPs, with sizes in the range 3–40 nm, are characterized by transmission electronic microscopy (TEM) and UV–Vis absorption spectroscopy, so as to evaluate their qualities. Moreover, a direct electrochemical detection protocol based on a cyclic voltammetry in water solution that involves the use of glassy carbon electrode is also applied to characterize the prepared NPs. The developed NPs and the related electroanalytical method seem to be with interest for future sensing and biosensing applications including DNA sensors and immunosensors.