Hierarchical Mn<Subscript>1.5</Subscript>Co<Subscript>1.5</Subscript>O<Subscript>4</Subscript> microspheres constructed from one-dimensional nanorods as high-performance anode material for lithium-ion battery

Mn_1.5Co_1.5O₄ hierarchical microspheres have been successfully synthesized via a solvothermal method and an annealing procedure. Mn_1.5Co_1.5O₄ exhibits advanced cycling performance, and it retains a reversible capacity of 633 mA h g^?1 at a current density of 400 mA g^?1 with a coulombic efficiency of 99.0% after 220 cycles. Its remarkable performance is attributed to the hierarchical structure assembled with nanorods, which increases the contact area between each nanorod and electrolyte. More significantly, the open space between neighboring nanorods and the pores on the surface of nanorods can improve Li⁺ ion diffusion rate. Furthermore, the nanorods have rapid one-dimensional Li⁺ diffusion channels, which not only possess a large specific surface area for high activity but accommodate the volume change during lithiation–delithiation processes. Therefore, Mn_1.5Co_1.5O₄ hierarchical microspheres can act as a promising alternative anode material for lithium-ion battery.     

Improved Li- storage performance of heat-treated InFeCoO<Subscript>4</Subscript> spinel prepared by glycine assisted chemical route

Herein, we show the synthesis of high-capacity anode, InFeCoO₄ spinel for lithium ion batteries (LIBs), by facile glycine-assisted chemical approach. The structure and morphology are evaluated by X-ray diffraction (XRD), X-ray absorption spectroscopy (XAS) and scanning electron microscopy (SEM) techniques, respectively. The pure phase formation of spinel InFeCoO₄ is confirmed from XRD pattern, whereas the oxidation state of Co in 2+ is determined from XAS analysis. Electrochemical performance of InFeCoO₄ in the half-cell configuration is evaluated by galvanostatic and cyclic voltammetry (CV) in the voltage window of 0.005–3.0 V vs. Li. When cycled at 60 mA g^?1, it shows a high first cycle reversible capacity of 750 (±10) mA h g^?1. However, slow capacity degradation is noticed upon cycling and reached 285 (±10) mA h g^?1 after 40 cycles. An improved Li-storage performance is noticed under similar cycling condition, when the electrode is heat-treated. It shows first cycle reversible capacity of 880 (±10) mA h g^?1 and reached 535 (±10) mA h g^?1 after 40 cycles. The coulombic efficiency is >98 % during cycling. The improved Li-storage performance is possibly due to the distribution of PVDF (binder) in the active materials as well as better electrical contact after heat treatment.     

Preparation of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> hollow microsphere/graphene/carbon nanotube flexible film as a binder-free anode material for lithium-ion batteries

A flexible Co₃O₄ hollow microsphere/graphene/carbon nanotube hybrid film is successfully prepared through a facile filtration strategy and a subsequent thermally treated process. The composition, morphology, and structure of the as-prepared film are characterized by X-ray diffraction, X-ray photoelectron spectrometer, scanning electron microscopy, and transmission electron microscopy. Based on the morphology characterizations on the hybrid film, the Co₃O₄ hollow microspheres are uniformly and closely attached on three-dimensional (3D) graphene/carbon nanotubes (GR/CNTs) network, which decreases the agglomeration of Co₃O₄ microspheres effectively. In this hybrid film, the 3D GR/CNT network which enhances conductance as well as prevents aggregation is a benefit to help Co₃O₄ to exert its lithium storage capabilities sufficiently. When used as a binder-free anode material for lithium-ion batteries, the hybrid film delivers excellent electrochemical properties involving reversible capacity (863 mAh g^?1 at a current density of 100 mA g^?1) and rate performance (185 mAh g^?1 at a current density of 1600 mA g^?1).     

Hierarchical Co<Subscript>3</Subscript>O<Subscript>4</Subscript>@C hollow microspheres with high capacity as an anode material for lithium-ion batteries

Three-dimensional hierarchical Co₃O₄@C hollow microspheres (Co₃O₄@C HSs) are successfully fabricated by a facile and scalable method. The Co₃O₄@C HSs are composed of numerous Co₃O₄ nanoparticles uniformly coated by a thin layer of carbon. Due to its stable 3D hierarchical hollow structure and uniform carbon coating, the Co₃O₄@C HSs exhibit excellent electrochemical performance as an anode material for lithium-ion batteries (LIBs). The Co₃O₄@C HSs electrode delivers a high reversible specific capacity, excellent cycling stability (1672 mAh g^?1 after 100 cycles at 0.2 A g^?1 and 842.7 mAh g^?1 after 600 cycles at 1 A g^?1), and prominent rate performance (580.9 mAh g^?1 at 5 A g^?1). The excellent electrochemical performance makes this 3D hierarchical Co₃O₄@C HS a potential candidate for the anode materials of the next-generation LIBs. In addition, this simple synthetic strategy should also be applicable for synthesizing other 3D hierarchical metal oxide/C composites for energy storage and conversion.     

Acacia gum-assisted co-precipitating synthesis of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion batteries

LiNi_0.5Co_0.2Mn_0.3O₂ particles of uniform size were prepared through carbonate co-precipitation method with acacia gum. The precursor of carbonate mixture was calcined at 800 °C, and a well-crystallized Ni-rich layered oxide was got. The phase structure and morphology were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The micro-sized particles delivered high initial discharge capacity of 164.3 mA h g^?1 at 0.5 C (1 C?=?200 mA g^?1) between 2.5 and 4.3 V with capacity retention of 87.5 % after 100 cycles. High reversible discharge capacities of 172.4 and 131.4 mA h g^?1 were obtained at current density of 0.1 and 5 C, respectively. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were performed to further study the LiNi_0.5Co_0.2Mn_0.3O₂ particles. Anyway, the excellent electrochemical performances of LiNi_0.5Co_0.2Mn_0.3O₂ sample should be attributed to the use of acacia gum.     

Scalable synthesis and superior performance of TiO<Subscript>2</Subscript>-reduced graphene oxide composite anode for sodium-ion batteries

TiO₂-reduced graphene oxide (RGO) composite was synthesized via a sol-gel process and investigated as an anode material for sodium-ion batteries (SIBs). A remarkable improvement in sodium ion storage with a reversible capacity of 227 mAh g^?1 after 50 cycles at 50 mA g^?1 is achieved, compared to that (33 mAh g^?1) for TiO₂. The enhanced electrochemical performance of TiO₂-RGO composite is attributed to the larger specific surface area and better electrical conductivity of TiO₂-RGO composite. The excellent performance of TiO₂-RGO composite enables it a potential electrode material for SIBs.     

Dandelion-like mesoporous Co<Subscript>3</Subscript>O<Subscript>4</Subscript> as anode materials for lithium ion batteries

A dandelion-like mesoporous Co₃O₄ was fabricated and employed as anode materials of lithium ion batteries (LIBs). The architecture and electrochemical performance of dandelion-like mesoporous Co₃O₄ were investigated through structure characterization and galvanostatic charge/discharge test. The as-prepared dandelion-like mesoporous Co₃O₄ consisted of well-distributed nanoneedles (about 40 nm in width and about 5 μm in length) with rich micropores. Electrochemical experiments illustrated that the as-prepared dandelion-like mesoporous Co₃O₄ as anode materials of LIBs exhibited high reversible specific capacity of 1430.0 mA h g^?1 and 1013.4 mA h g^?1 at the current density of 0.2 A g^?1 for the first and 100th cycle, respectively. The outstanding lithium storage properties of the as-prepared dandelion-like mesoporous Co₃O₄ might be attributed to its dandelion-like mesoporous nanostructure together with an open space between adjacent nanoneedle networks promoting the intercalation/deintercalation of lithium ions and the charge transfer on the electrode. The enhanced capacity as well as its high-rate capability made the as-prepared dandelion-like mesoporous Co₃O₄ to be a good candidate as a high-performance anode material for LIBs.     

Hierarchical porous ZnMn<Subscript>2</Subscript>O<Subscript>4</Subscript> synthesized by the sucrose-assisted combustion method for high-rate supercapacitors

A simple sucrose-assisted combustion and subsequent high-temperature calcination route have been employed to prepare hierarchical porous ZnMn₂O₄ nanostructure. When used as an electrode for supercapacitor, the ZnMn₂O₄ electrode displays a high specific capacitance of 411.75 F g^?1 at a current density of 1 A g^?1, remarkable capacitance retention rate of 64.28 % at current density of 32 A g^?1 compared with 1 A g^?1, as well as excellent cycle stability (reversible capacity retention of 88.32 % after 4000 cycles). The outstanding electrochemical performances are mainly attributed to its hierarchical porous architecture, which provides large reaction surface area, fast ion and electron transfer, and good structure stability. All these impressive results demonstrate that ZnMn₂O₄ shows promise for its application in supercapacitors.     

Facile synthesis of N-doped carbon-coated Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode for application in high-rate lithium ion batteries

A facile sol-gel approach for the synthesis of lithium titanate composite decorated with N-doped carbon material (LTO/NC) is proposed. Urea is used as a nitrogen source in the proposed approach. The LTO/NC exhibits superior electrochemical performances as an electrode material for lithium-ion batteries, delivering a discharge capacity of as high as 103 mAh g^?1 at a high rate of 20 C and retaining a stable reversible capacity of 90 mAh g^?1 after 1000 cycles, corresponding to 100% capacity retention. These excellent electrochemical performances are proved by the nanoscale structure and N-doped carbon coating. NC layers were uniformly dispersed on the surface of LTO, thus preventing agglomeration, favoring the rapid migration of the inserted Li ion, and increasing the Li⁺ diffusion coefficient and electronic conductivity. LTO with the appropriate amount of NC coating is a promising anode material with applications in the development of high-powered and durable lithium-ion batteries.     

Cu-supported carbon networks containing SnO<Subscript>2</Subscript> as three-dimensional anodes for lithium-ion batteries

Cu-supported SnO₂@C composite coatings constructed by interconnected carbon-based porous branches were fabricated by annealing Cu foils with films formed by knife coating DMF solution containing SnCl₂, polyacrylonitrile (PAN), and poly(methyl methacrylate) (PMMA) on their surface in vacuum. The carbon-based porous branches consist of amorphous carbon matrices, SnO₂ nanoparticles with a size of 30–100 nm mainly encapsulated inside, and many micropores with a size of 1–5 nm. The three-dimensional (3D) porous network structures of the SnO₂@C composite were achieved by volatilization of PMMA and pyrolysis of SnCl₂. The SnO₂@C composite coatings demonstrate good cyclic performance with a high reversible capacity of 642 mA h g^?1 after 100 cycles at a current density of 50 mA g^?1 without apparent capacity fading during cycling and excellent rate performance with a capacity of 276 mA h g^?1 at a high current density up to 10 A g^?1.     

Fabrication and electrochemical investigation of MWO<Subscript>4</Subscript> (M = Co,Ni) nanoparticles as high-performance anode materials for lithium-ion batteries

In this work, the MWO₄ (M = Co, Ni) nanoparticles were successfully synthesized by a facile one-step hydrothermal method and used as novel anode materials for LIBs. The micromorphology of obtained CoWO₄ and NiWO₄ was uniform nanoparticles with the size of ~60 and ~40 nm, respectively, by structural characterization including X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). When tested as lithium-ion battery anode, CoWO₄ nanoparticles exhibited a stabilized reversible capacity of 980 mA h g^?1 at 200 mA g^?1 after 120 cycles and 632 mA h g^?1 at 1000 mA g^?1 even after 400 cycles. And, the discharge capacity was as high as 550 mA h g^?1 at the 400th cycle for NiWO₄ nanoparticles. The excellent electrochemical performance could be attributed to the unique nanoparticles structure of the materials, which can not only shorten the diffusion length for electrons and lithium ions but also provide a large specific surface area for lithium storage.     

The facile in situ preparation and characterization of C/FeOF/FeF<Subscript>3</Subscript> nanocomposites as LIB cathode materials

C/FeOF/FeF₃ nanocomposite was synthesized by a facile in situ partial oxidation method. High-resolution transmission electron microscopy (HR-TEM) showed a special texture comprised of interpenetrating nanodomains of FeOF and FeF₃. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements revealed that the introduction of nanodomain FeOF enhanced both the electronic and ionic conductivity of the composite material. Therefore, the improvement of electron and lithium-ion dynamics resulted in the significant enhancement of the electrochemical performances of the material at ambient temperature. At a current density of 20 mA g^?1 within potential range 1.5–4.5 V, the specific capacities of the first ten circles were maintained at about 400 mAh g^?1 _. This material also exhibited excellent cycling capacity retention capability especially for high C rates. When the current density further increased to 100 and 200 mA g^?1, a steady capacity of 80 and 60 mAh g^?1 was observed, respectively. Furthermore, nearly no capacity loss was observed for the followed cycles. The discharge platforms based on intercalation and conversion reaction were also heightened by about 0.4 V, which increased the contribution of high voltage capacities. Compared to C/FeF₃, C/FeOF/FeF₃ is showing more of capacitive behavior, which also contributes to the high specific capacity delivered and is believed to be closely related to the enlarged nanodomain interfaces between two electrochemical active materials. An expansion-cracking-oxidation mechanism was proposed to explain the formation of this interpenetrating nanodomains of FeOF and FeF₃.     

Mo-doped V<Subscript>2</Subscript>O<Subscript>5</Subscript> hierarchical nanorod/nanoparticle core/shell porous microspheres with improved performance for cathode of lithium-ion battery

Mo-doped V₂O₅ hierarchical nanorod/nanoparticle core/shell porous microspheres (MVHPMs) were prepared via a simple hydrothermal approach using ammonium metavanadate and ammonium molybdate as precursors followed by a thermal annealing process. The samples were characterized by XRD, SEM, TEM, EDS, and XPS carefully; it confirmed that porous microspheres with uniform Mo doping in the V₂O₅ matrix were obtained, and it contains an inner core self-assembled with 1D nanorods and outer shell consisting of nanoparticles. A plausible growth mechanism of Mo-doped V₂O₅ (Mo-V₂O₅) porous microspheres is suggested. The unique microstructure made the Mo-V₂O₅ hierarchical microspheres a good cathode material for Li-ion battery. The results indicate the synthesized Mo-V₂O₅ hierarchical microspheres exhibit well-improved electrochemical performance compared to the undoped samples. It delivers a high initial reversible capacity of 282 mAh g^?1 at 0.2 C, 208 mAh g^?1 at 2 C, and 111 mAh g^?1 at 10 C, and it also exhibits good cycling stabilities; a capacity of 144 mAh g^?1 is obtained after 200 cycles at 6 C with a capacity retention of >?82%, which is much high than that of pure V₂O₅ (95 mAh g^?1 with a capacity retention of 72%).

Open image in new window

Graphical Abstract Mo-doped V₂O₅ hierarchical porous microspheres with improved LIB performance

     

Vertical aligned V<Subscript>2</Subscript>O<Subscript>5</Subscript> nanoneedle arrays grown on Ti substrate as binder-free cathode for lithium-ion batteries

V₂O₅ nanoneedle arrays were grown directly on titanium (Ti) substrate by a facile solvothermal route followed with calcination at 350 °C for 2 h. The as-prepared V₂O₅ nanoneedles are about 50 nm in diameter and 800 nm in length. The electrochemical behavior of V₂O₅ nanoarrays as binder-free cathode for lithium-ion batteries (LIBs) was evaluated by cyclic voltammetry and galvanostatic discharge/charge tests. Compared with V₂O₅ powder electrode, V₂O₅ nanoneedle arrays electrode exhibited improved electrochemical performance in terms of high discharge capacity of 262.5 mA h g^?1 between 2.0 and 4.0 V at 0.2 C, and high capacity retention up to 77.1% after 100 cycles. Under a high current rate of 2 C, a discharge capacity of about 175.6 mA h g^?1 can be maintained. The enhanced performance are mainly due to the intimate contact between V₂O₅ nanoneedle active material and current collector, which enable shortened electron transfer pathway and improved charge transfer kinetics, demonstrating their potential applications in high rate electrochemical storage devices.     

Parallelepipedally shaped ZnCo<Subscript>2</Subscript>O<Subscript>4</Subscript> particles with a hierarchical porous structure as an anode for lithium-ion batteries

The micrometer-sized ZnCo₂O₄ parallelepipeds with a hierarchical porous structure have been fabricated by a simple two-step procedure, i.e., the synthesis of the Zn_1/3Co_2/3CO₃ parallelepipeds and the subsequent calcination. When tested in lithium-ion batteries (LIBs), the hierarchical porous ZnCo₂O₄ parallelepipeds could exhibit a reversible capacity of >860 mAh g^?1 at a current density of 0.1 C. This clearly demonstrates the potential use of the hierarchical porous ZnCo₂O₄ parallelepipeds in LIBs. The high electrochemical performance of the hierarchical porous ZnCo₂O₄ parallelepipeds might originate from the unique porous structure which consists of the secondary ZnCo₂O₄ particles. First, the porous structure allows for a better accessibility of the active material to the Li⁺ ion storage, favoring easier diffusion of electrolyte in and out of electrode material. Second, the presence of the secondary particles shortens a pathway of Li⁺ diffusion in ZnCo₂O₄, facilitating the better utilization of the active material.     

Nanocrystalline Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> electrodes for supercapattery application

Nanocrystalline Li₂TiO₃ was successfully synthesized using solid-state reaction method. The microstructural and electrochemical properties of the prepared material are systematically characterized. The X-ray diffraction pattern of the prepared material exhibits predominant (002) orientation related to the monoclinic structure with C2/c space group. HRTEM images and SAED analysis reveal the well-developed nanostructured particles with average size of ～40 nm. The electrochemical properties of the prepared sample are carried out using cyclic voltammetry (CV) and chronopotentiometry (CP) using Pt//Li₂TiO₃ cell in 1 mol L^?1 Li₂SO₄ aqueous electrolyte. The Li₂TiO₃ electrode exhibits a specific discharge capacity of 122 mAh g^?1; it can be used as anode in Li battery within the potential window 0.0–1.0 V, while investigated as a supercapacitor electrode, it delivers a specific capacitance of 317 F g^?1 at a current density of 1 mA g^?1 within the potential range ?0.4 to +0.4 V. The demonstration of both anodic and supercapacitor behavior concludes that the nanocrystalline Li₂TiO₃ is a suitable electrode material for supercapattery application.     

A novel carbon source coated on C-LiFePO<Subscript>4</Subscript> as a cathode material for lithium-ion batteries

The poor electronic conductivity and low lithium-ion diffusion are the two major obstacles to the largely commercial application of LiFePO₄ cathode material in power batteries. In order to improve the defects of LiFePO₄, a novel carbon source polyacrylonitrile (PAN), which would form the hierarchical porous structure after carbonization, is fabricated and used. This work comes up with a simple and facile carbothermal reduction method to prepare porous-carbon-coated LiFePO₄ (C-LiFePO₄-PC) composite and to study the effect of carbon-coated temperature on ameliorating the electrochemical performance. The obtained C-LiFePO₄-PC composite shows a high initial discharge capacity of 164.1 mA h g^?1 at 0.1 C and good cycling stability as well as excellent rate capacity (49.0 mA h g^?1 at 50 C). The most possible factors that improve the electrochemical performance could be related to the enhancement of electronic conductivity and the existence of porous carbon layers. In a word, the C-LiFePO₄-PC material would become an excellent candidate for application in the fields of lithium-ion batteries.     

Improving the electrochemical performance of Li-rich Li<Subscript>1.2</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.54</Subscript>O<Subscript>2</Subscript> cathode material by LiF coating

To suppress the capacity fade of Li-rich Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material as cathode materials for lithium-ion battery, we introduce a LiF coating layer on the surface to improve the cycling performance of Li_1.2Ni_0.13Co_0.13Mn_0.54O₂ material. The modified sample shows a capacity of 163.2 mAh g^?1 with a capacity retention of 95% after 100 cycles at a current density of 250 mA g^?1, while the pristine sample only delivers a capacity of 129.9 mAh g^?1 with a capacity retention of 82%. Compared with the pristine material, the LiF-modified sample exhibits an obvious enhancement in the electrochemical performance, which will be very beneficial for this material to be commercialized on the new energy vehicles and other related areas.     

Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> quantum dots on 3D-framed graphene aerogel as an advanced anode material in lithium-ion batteries

Three-dimensional fabricated Fe₃O₄ quantum dots/graphene aerogel materials (Fe₃O₄ QDs/GA) were obtained from a facile hydrothermal strategy, followed by a subsequently heat treatment process. The Fe₃O₄ QDs (2–5 nm) are anchored tightly and dispersed uniformly on the surface of three-dimensional GA. The as-prepared anode materials exhibit a high reversible capacity of 1078 mAh g^?1 at a current density of 100 mA g^?1 after 70 cycles in lithium-ion batteries (LIBs) system. Moreover, the rate capacity still remains 536 mAh g^?1 at 1000 mA g^?1. The enhanced electrochemical performance is attributed to that the GA not only acts as a three-dimensional electronic conductive matrix for the fast transportation of Li⁺ and electrons, but also provides with double protection against the aggregation and pulverization of Fe₃O₄ QDs during cycling. Apparently, the synergistic effects of the three-dimensional GA and the quantum dots are fully utilized. Therefore, the Fe₃O₄ QDs/GA composites are promising materials as advanced anode materials for LIBs.     

Tailoring MoS2 Ultrathin Sheets Anchored on Graphene Flexible Supports for Superstable Lithium‐Ion Battery Anodes

2D MoS₂ has a significant capacity decay due to the stack of layers during the charge/discharge process, which has seriously restricted its practical application in lithium‐ion batteries. Herein, a simple preform‐in situ process to fabricate vertically grown MoS₂ nanosheets with 8–12 layers anchored on reduced graphene oxide (rGO) flexible supports is presented. As an anode in MoS₂/rGO//Li half‐cell, the MoS₂/rGO electrode shows a high initial coulomb efficiency (84.1%) and excellent capacity retention (84.7% after 100 cycles) at a current density of 100 mA g^?1. Moreover, the MoS₂/rGO electrode keeps capacity as high as 786 mAh g^?1 after 1000 cycles with minimum degradation of 54 µAh g^?1 cycle^?1 after being further tested at a high current density of 1000 mA g^?1. When evaluated in a MoS₂/rGO//LiCoO₂ full‐cell, it delivers an initial charge capacity of 153 mAh g^?1 at a current density of 100 mA g^?1 and achieves an energy density of 208 Wh kg^?1 under the power density of 220 W kg^?1.