无限流体中孔隙介质圆柱周向导波的传播特性

为研究无限大流体约束的孔隙圆柱中周向导波的传播规律,分析孔隙参数对导波传播特性的影响,建立了无限流体中孔隙介质圆柱的理论模型,利用孔隙介质弹性波动理论,建立了周向导波频散方程,通过数值模拟计算得到无限流体中孔隙介质圆柱的频散曲线,探讨了圆柱半径和孔隙参数对导波传播特性的影响,并对导波的衰减特性进行了分析;通过数值计算,得到了周向导波的时域波形,讨论了孔隙参数对波形的影响.结果表明,孔隙介质圆柱半径的改变影响圆柱尺度,孔隙度的改变影响孔隙介质中体声波的波速,都对周向导波频散曲线产生一定的影响,所得到的频散曲线特征及衰减曲线与时域波形吻合.研究结果对开展无限流体中孔隙介质圆柱的超声无损评价提供了一定的理论参考.     

流体-孔隙介质圆柱界面波传播特性

研究流体-孔隙介质圆柱界面波传播特性,分析孔隙介质孔隙率等参数对频散曲线的影响。理论上建立了无限大流体包裹孔隙介质圆柱界面波的模型,利用孔隙介质弹性波动理论,通过数值模拟计算得到流体-孔隙介质圆柱的频散曲线及时域波形,并分析了孔隙介质为开孔和闭孔状态下孔隙介质圆柱半径、孔隙率及渗透率对频散曲线的影响。结果表明,时域上斯通利波可以被明显区分开,孔隙介质圆柱半径的变化改变了圆柱尺度,孔隙率的变化改变了孔隙介质的纵、横波波速,因此对于斯通利波频散曲线的影响较大。而渗透率的变化既不改变圆柱的尺度也不改变孔隙层的纵、横波速度,因此对斯通利波频散曲线影响较小。     

曲线坐标系下孔隙介质圆柱纵向表面波的传播特性

为了研究孔隙介质圆柱纵向表面波的传播规律,分析其频散和衰减特性,在正交曲线坐标系下建立了表面波的频散方程,通过数值计算得到频散曲线,将纵向导波最低模态与表面波进行对比,并分析了曲率半径及孔隙参数对表面波频散和衰减的影响。结果表明,当频率足够大时,导波最低模态的频散曲线与表面波近似;在同一频率下,表面波的相速度随曲率半径的增大而增大,随孔隙度的增大而减小;表面波的衰减随孔隙度的增大而增大。研究结果为开展孔隙介质圆柱结构的超声无损评价提供了一定的理论参考。     

Surface effect on size-dependent wave propagation in nanoplates via nonlocal elasticity

Within the framework of nonlocal elasticity, the surface layer model is proposed to investigate the wave propagation characteristics in a single-layered nanoplate. The general solutions of nonlocal governing equations are expressed using partial wave technique and the nonclassical boundary conditions are derived. The dispersion relation with the effects of surface and nonlocal small-scale is obtained, and the size-dependent dispersion behaviour is demonstrated. The impacts of surface elasticity, residual surface stress and nonlocal parameter on the dispersion curves of the lowest-order two modes are illustrated. Numerical examples reveal that both the surface effect and nonlocal small-scale effect can obviously decrease the magnitude of phase velocity, and the thinner nanoplate corresponds to the smaller wave velocity and the narrower frequency bandwidth.     

浅海起伏海面下气泡层对声传播的影响

分析了起伏海面下风浪引起的气泡层对海面反射损失和对声传播的影响.一方面,气泡层会改变原来水中的声速剖面;另一方面,气泡层会对声波产生散射和吸收作用.考虑以上两方面的因素,分析了不同风速下气泡层对海面反射损失和声传播损失的影响,仿真发现,在风速大于10 m/s时,对于2 k Hz以上频率时气泡层对小掠射角下海面反射损失的影响不可忽视.在给定的水声环境中,当声源深度和接收深度都为7 m时,风速为16 m/s的风浪下生成的气泡层,在10 km处对3 k Hz的声传播损失的影响达到8.1 d B.当声源深度和接收深度都为18 m时,风速为16 m/s的风浪下生成的气泡层,在10 km处对3 k Hz的声传播损失的影响达到4 d B.     

流体/准饱和多孔介质中伪Scholte波的传播特性

研究流体/多孔介质界面Scholte波的传播特性对于水下勘探、地震工程等领域具有重要意义.本文基于Biot理论和等效流体模型,采用势函数方法,推导了描述有限厚度流体/准饱和多孔半空间远场界面波的特征方程和位移、孔压计算公式.在此基础上,分别以砂岩和松散沉积土为例,研究了流体/硬多孔介质和流体/软多孔介质两种情况下,可压缩流体层厚度和多孔介质饱和度对伪Scholte波传播特性的影响.结果表明：多孔介质软硬程度显著影响界面波的种类、相速度、位移和水压力分布;有限厚度流体/饱和多孔半空间界面处伪Scholte波相速度与界面波波长和流体厚度的比值有关;孔隙水中溶解的少量气体对剪切波的相速度的影响不大,对压缩波相速度、伪Scholte波相速度和孔隙水压力分布影响显著.     

各向异性渗流条件下弹性波的传播特征

研究了弹性波在非均匀裂纹孔隙介质中的传播特性,建立了各向异性喷射流模型.当弹性波通过裂纹孔隙介质时,由于波的扰动及裂纹和孔隙几何结构的不一致,导致在裂纹内部及裂纹与周边孔隙之间同时存在着流体压力梯度.此时的弹性波波动响应中包含着裂纹内连通性特征和背景孔隙渗透率信息.流体的动态流动过程使得介质的等效弹性参数为复数(非完全弹性),并且具有频率依赖性.当弹性波为低频和高频极限时,介质为完全弹性;当处于中间频段时,波有衰减和频率依赖.裂纹孔隙介质的各向异性连通性(渗透率)对应着各向异性特征频率(当渗流长度等于非均匀尺度时的弹性波频率),波的传播受到裂纹内连通性的影响.在一定频段内,随着裂纹厚度的增加,将出现第二峰值,峰值大小同时受到裂纹厚度和半径的影响.     

孔隙介质包裹的充液管道结构中导波传播特性

研究孔隙介质包裹的充液管道中纵向导波传播特性,分析孔隙介质参数对频散曲线的影响。建立了孔隙介质包裹充液管道的结构模型,利用孔隙介质弹性波动理论,建立对应的频散方程,数值模拟计算得到该模型的频散曲线和时域波形,并分析了孔隙介质参数以及管壁厚度对频散曲线的影响。结果表明孔隙介质的渗透率对于导波频散的影响较小,孔隙度的改变对时域波形的位移幅度影响较大。同时,导波存在衰减,且衰减随孔隙度增大而增大。所得结论为埋地管道无损检测方面提供一定理论参考。     

Modeling of elastic wave propagation on a curved free surface using an improved finite-difference algorithm

Modelling and understanding the effect of elastic wave propagation along a curved free surface has been one of the important issues in seismic exploration[1—3], earth seis-mology[4], and non-destructive ultrasonic detection[5]. Several approaches have beenproposed for simulating wave propagation in heterogeneous media with a topographic stress-release boundary. These include finite-element methods (FEM), boundary element methods (BEM), finite-difference methods (FDM), pseudo-spectral metho…     

管道弯头对低频纵向导波传播特性影响分析

管道弯头显著改变了导波传播特性,影响了对检测信号的解读,研究弯头对导波传播特性的影响是实现复杂管道系统导波检测的基础。采用半解析有限元法计算弯管导波频散曲线,分析了弯管导波频散曲线所呈现的不同特征,并基于弯管导波频散曲线,以低频L(0,1)模态导波为研究对象,实验研究了低频L(0,1)模态导波通过管道弯头时的模态变换特征。研究结果发现,当L(0,1)模态导波通过管道弯头时,不仅会发生L(0,1)到F(1,1)的模态变换,还会模态变换出反向L(0,1)模态导波,即弯头反射现象,且随着激励频率的降低和弯头弯曲半径的减小,弯头反射现象愈发明显。研究结果将深化对弯管导波传播特性的认识,推动导波检测技术在复杂管道系统检测中的应用。     

Surface plasmon wave propagation along single metal wire

Recently,the single metal wire(SW) has become attractive for its potential applications in the terahertz and higher frequency range.However,as the most simple and typical surface plasmon polariton(SPP) transmission line,its study seems far from enough.Many important transmission behaviours have not been explained satisfactorily from the viewpoint of physics.In this paper,making use of the modified Drude model(MDM) based on the Sommerfeld theory,the transmission behaviours of SPPs along SW are systemically investigated theoretically.Some important physical phenomena such as the mode transformation,the lifetime of the radiative mode and the resonance frequency are revealed,and their mechanisms are explored.The results obtained in the paper will facilitate a general understanding of the features and the physical essence of the SPP transmission,not only for SW itself but also for other SPP transmission lines.     

装置参数对狭缝天线激发的等离子体表面波传播的影响

采用时域有限差分法对矩形结构装置的等离子体表面波传播进行了三维数值模拟.研究了装置参数(如介质板相对介电常数、厚度以及介质板上方空气间隙)对天线阵列激发的等离子体表面波传播的影响,给出了合适的介质板相对介电常数和厚度,并指出空气间隙的存在会严重削弱天线阵列对表面波的激发.计算结果可为大面积矩形表面波等离子体源装置的优化设计提供参考. 关键词： 时域有限差分法 等离子体表面波 狭缝天线     

The effect of surface stress on the propagation of Lamb waves

This work investigates the possibility of the propagation of Lamb waves in thin solid layers with external traction free surfaces, in the presence of surface elasticity, inertia and residual stress. It is demonstrated that such waves do exist and that their characteristics can be quite different from their classical counterparts. The governing equations with non-classical boundary conditions involving the bulk and surface stress are solved exactly in the frequency-wavenumber domain. This solution is utilized to compute the Lamb wave modes for different layer thicknesses. An efficient strategy to capture all the modes of Lamb waves within a given frequency window is outlined. It is shown that the effect of surface elasticity and inertia becomes significant with increasing frequency and decreasing layer thickness, where the number of modes participating within a given frequency window is more than that permitted by the classical theory. Further, it is observed that the nature of the Lamb wave modes (in terms of negative dispersion) in the presence of surface stress is similar to what predicted by the nonlocal theory and microstructure based continuum theory.     

Correlation between helical surface waves and guided modes of an infinite immersed elastic cylinder

Scattering of obliquely incident plane acoustic waves from immersed infinite solid elastic cylinders is a complex phenomenon that involves generation of various types of surface waves on the body of the cylinder. Mitri [F.G. Mitri, Acoustic backscattering enhancement resulting from the interaction of an obliquely incident plane wave with an infinite cylinder, Ultrasonics 50 (2010) 675-682] recently showed that for a solid aluminum cylinder, there exist acoustic backscattering enhancements at a normalized frequency of ka?0.1. The incidence angle α_c at which these enhancements are observed lies between the first (longitudinal) and second (shear) coupling angles of the cylinder. He also confirmed the observations previously reported by the authors that there exist backscattering enhancements of the dipole mode at large angles of incidence where no wave penetration into the cylinder is expected. In this paper, physical explanations are provided for the aforementioned observations by establishing a correlation between helical surface waves generated by oblique insonification of an immersed infinite solid elastic cylinder and the longitudinal and flexural guided modes that can propagate along the cylinder. In particular, it is shown that the backscattering enhancement observed at ka?0.1 is due to the excitation of the first longitudinal guided mode travelling at the bar velocity along the cylinder. It is also demonstrated that the dipole resonance mode observed at incidence angles larger than the Rayleigh coupling angle is associated with the first flexural guided mode of the cylinder. The correlation established between the scattering and propagation problems can be used in both numerical and experimental studies of interaction of mechanical waves with cylinders.     

表征超大规模集成电路互连纳米薄膜硬度特性的声表面波的频散特性

利用声表面波(SAW)的频散特性来表征超大规模集成电路(ULSI)互连系统中低介电常数(k)薄膜的物性具有准确、快速、对材料无损伤等突出优点.研究了Si(100)衬底上淀积低k薄膜的分层结构中，SAW沿任意方向传播的色散关系.引入坐标变换后，单层薄膜特征矩阵从9阶降到6阶，双层薄膜特征矩阵从15阶降到10阶，大幅度提高了计算速度，有利于生产ULSI过程中的在线监测. 关键词： 超大规模集成电路 声表面波 传输方向 频散特性     

太赫兹波在一维反铁磁/电介质准周期光子晶体的传输性质

本文利用传递矩阵方法研究了电磁波倾斜入射时,一维反铁磁/电介质准周期光子晶体的透射性质.反铁磁层和电介质层按Fibonacci数列排列构成准周期光子晶体.通过数值模拟发现光子禁带中有透射峰出现, 而且随着准周期光子晶体级数的增加透射峰的数目也在增加.此外,透射峰受电介质层的介电常数、入射角度和电磁波偏振影响明显. 关键词： 反铁磁层 准周期光子晶体 太赫兹波传输性质     

含少量气泡流体饱和孔隙介质中的弹性波

考虑孔隙流体中含有少量气泡,且气泡在声波作用下线性振动,研究声波在这种孔隙介质中的传播特性.本文先由流体质量守恒方程和孔隙度微分与流体压力微分的关系推导出了含有气泡形式的渗流连续性方程;在处理渗流连续性方程中的气体体积分数时间导数时,应用Commander气泡线性振动理论导出气体体积分数时间导数与流体压强时间导数的关系,进而得到了修正的Biot形式的渗流连续性方程;最后结合Biot动力学方程求得了含气泡形式的位移场方程,便可得到两类纵波及一类横波的声学特性.通过对快、慢纵波的频散、衰减及两类波引起的流体位移与固体位移关系的考察,发现少量气泡的存在对快纵波和慢纵波的传播特性影响较大.     

Theory of electromagnetic wave propagation in a longitudinally periodic cylinder

Thinking of photonic crystals, we investigate the theory of electromagnetic wave propagation in a perfectly conducting semi-cylinder endowed with a periodic permittivity along its axis while its circular base is illuminated by an harmonic Bessel beam, symmetric around the cylinder axis. We prove that the Floquet-Bessel expansions of electromagnetic fields whose Floquet parts are solutions of a Mathieu equation. is a suitable tool to handle this kind of problems.     

声波在含气泡液体中的线性传播

为了探讨含气泡液体对声波传播的影响, 研究了声波在含气泡液体中的线性传播. 在建立含气泡液体的声学模型时引入气泡含量的影响,建立气泡模型时引用 Keller的气泡振动模型并同时考虑气泡间的声相互作用,得到了经过修正的气泡振动方程. 通过对含气泡液体的声传播方程和气泡振动方程联立并线性化求解,在满足 (ω R₀)/c << 1 的前提下,得到了描述含气泡液体对声波传播的衰减系数和传播速度. 通过数值分析发现,在驱动声场频率一定的情况下,气泡含量的增加及气泡的变小均会导致衰减系数增加和声速减小;气泡的体积分数和大小一定时, 驱动声场频率在远小于气泡谐振频率的情况下,声速会随驱动频率的增加而减小; 气泡间的声相互作用对声波传播速度及含气泡液体衰减系数的影响不明显.最终认为气泡的大小、 数量和驱动声场频率是影响声波在含气泡液体中线性传播的主要因素. 关键词： 含气泡液体 线性声波 声衰减系数 声速