Use of factorial experimental design for the rapid evaluation of main and interactive factors affecting linearity in calibration curves for sulfate analysis by ion chromatography

Analytical results of anion determination by suppressed ion chromatography are significantly affected by calibration curve calculation. In this paper, as expected, eluent pK_a is shown to influence calibration linearity in the range 1–20 mg/l sulfate, with A carbonate-hydrogencarbonate mixture producing a larger non-linearity than NaOH. Evidence is given for very large errors (about 30–40%) in estimating sample sulfate concentration when linear regression is used instead of a quadratic calibration curve. This study was performed following a 2⁴ run full factorial experimental design, including eluent pK_a, counterion type, solution composition and current level for background suppression as main variables.     

Reversed-phase ion-interaction chromatography of Cu(I)-cyanide complexes

It has been established that during the separation of Cu(I)-cyanide complexes, the cyanide:Cu(I) molar ratio, R of the eluted complex remained constant irrespective of the R value injected onto the column, and there was considerable tailing of the unretained cyanide peak and fronting of the Cu(I)-cyanide peak in an eluent containing no cyanide. The addition of small amounts of cyanide (100 μM) to the eluent resulted in the elimination of these effects on peak shape and a significant increase in the retention of the Cu(I)-cyanide species. These results suggested that more than one Cu(I)-cyanide complex may be present in the Cu(I)-cyanide peak in an eluent containing no cyanide. Three different detection systems [Fourier transform Infrared (FTIR) and photodiode array spectrophotometry and a post-column reaction (PCR)], were used to determine changes that occurred to the Cu(I)-cyanide complexes during the separation with eluents containing from 0 to 100 μM cyanide. The FTIR approach was unsuccessful due to a lack of sensitivity. The UV spectrum of the Cu(I) peak in any one eluent remained constant, irrespective of the composition of the injected sample, but there were distinct changes in this spectrum among eluents. Similarly, the R value of the Cu(I) peak determined by PCR remained the same in any one eluent but ranged from about 2.5 to about 3.4 for these eluents. The R value was found to vary within the eluted Cu(I)-cyanide peak, especially in an eluent containing no added cyanide. These results show that more than one Cu(I)-cyanide complex is present in the eluted peak and that in the absence of cyanide in the eluent, the eluted peak consists of a mixture of the di- and tricyano complexes of Cu(I).     

Determination of glyphosate by ion chromatography

An ion chromatography system for the determination of glyphosate was described. Ion chromatograph was carried out by suppressed conductivity detection (DX-100). The eluent contained 9 mmol l⁻¹ Na₂CO₃ and 4 mmol l⁻¹ NaOH. The detection limit was 0.042 μg ml⁻¹ (S/N=3). The relative standard deviation was 1.99% and the correlation coefficient of the calibration curve for area was 0.9995. The linear range was 0.042100 μg ml⁻¹. Common inorganic ion and organic acids did not interfere. The recovery was 96.4103.2%. The method was simple, rapid, reliable and inexpensive.     

Determination of pharmaceuticals and related impurities by capillary electrophoresis

In the first part of this work, the use of capillary electrophoresis (CE) for the separation of two groups of pharmaceuticals, namely a metabolite of tamoxifen and a basic drug substance, DS1, was investigated. The effects of pH and types of modifiers, e.g. surfactant, bile salt, γ-cyclodextrin and hydroxypropyl-β-cyclodextrin on selectivity, separation and peak shape were studied. Besides achieving complete separation of the compounds, the CE system was capable of providing separation with significant improvements in overall peak shape of the compounds compared with HPLC. In the case of the basic drug substance DS1, validation of the CE system developed in terms of linearity, selectivity, sensitivity and reproducibility was satisfactorily performed. At the same time, a study of the sample solvent matrix effects on the separation of this group of compounds was examined. The system was successfully applied to the analysis of laboratory-synthesized samples. Good correlation was observed between CE and HPLC, although higher efficiency and faster speed of separation were obtained using the CE system developed. For the tamoxifen metabolite, special emphasis was placed on the use of CE for the separation of the pair of isomers. This was readily achieved through the introduction of γ-cyclodextrin in the electrolyte. Resolution of at least 1.5 was obtained for the isomers using the CE method.     

Effect of soluble calcium on the determination of the labile metal content of sediments with ion-exchangers

Equilibration of sediments with cation-exchangers results in a transfer of loosely bound labile metal species to the exchanger phase. Dissolution of the matrix is also promoted and selectivity rules suggest that some of the cations released (particularly Ca) could effectively compete with metal ions for exchange sites. This potential source of error has been evaluated by studying synthetic mixtures of Ca²⁺ and other metal ions (Cu²⁺, Pb²⁺, Cd²⁺, Zn²⁺) and by analysis of two calcium-rich wastes (a calcine and a jarosite). The ion uptake most influenced by calcium competition was that of zinc; uptake of lead was least affected. For minimum error, i.e., optimum transfer of “available” or “labile” metal ion, the level of free Ca²⁺ introduced into the solution should not exceed 300 mg/l., and the amount of exchanger added must provide an excess of exchange sites relative to the amount of cations released from the sample. By use of exchangers of different types it is possible to attempt some classification of the labile metal content, e.g., acid-displaced, exchangeable, salts of weak acids.     

Ion chromatographic separation of alkali metal and ammonium cations on a C18 reversed-phase column

The separation of alkali metal (Li⁺, Na⁺, K⁺, Rb⁺ and Cs⁺) and ammonium cations on a C₁₈ reversed-phase column using three anionic surfactants [sodium 1-eicosyl sulphate, sodium dodecyl benzenesulphonate and sodium dodecyl sulphate (SDS)] is described. Two methods were examined: (a) “permanent” coating, with the use of a C₁₈ reversed-phase column previously coated with the surfactants; and (b) dynamic coating, with addition of the surfactants to the mobile phase. With method (a) the separation of the six cations was achieved with SDS. However, the retention times gradually decreased owing to dissolution of the SDS coating. Good separation was obtained with method (b), where 10 mM HNO₃ containing 0.1 mM SDS was used as the mobile phase with conductivity detection, and it was applied satisfactorily to real samples. The effect of system peaks on determination is also discussed.     

Ion-exclusion chromatography of aliphatic car☐ylic acids on a cation-exchange resin by elution with polyvinyl alcohol

Ion-exclusion chromatography of aliphatic car☐ylic acids of different acidity (pK_a) and hydrophobicity was investigated on a polystyrene-divinylbenzene (PS-DVB) based strongly acidic cation-exchange resin in the H⁺ form and conductivity detection by elution with polyvinyl alcohol (PVA). When water was used as an eluent, the resolution of the car☐ylic acids was very low and the peak accompanied a fronting depending on their hydrophobicities. Therefore, to improve the peak shape and the peak resolution, aqueous eluents containing PVAs (degrees of polymerization, n=500, 1500and2000) with many OH groups were tested for the ion-exclusion chromatographic separation of the car☐ylic acids. When aqueous eluents containing PVA were used, the fronting was decreased dramatically by the effect of increased hydrophilicity of the PS-DVB cation-exchange resin surface due to adsorption of OH group in PVA. The high resolution ion-exclusion chromatographic separation without the fronting and highly sensitive conductimetric detection of the car☐ylic acids was accomplished successfully by elution with a 0.2% PVA (n=1500)-10% methanol-water.     

Spectres de rotation de la molécule de chlorobenzéne : I. Variétés isotopiques monosubstituées et structure rs

The microwave spectra of chlorobenzene “(1)-³⁵Cl”, all eight mono-[“(1)-³⁷Cl”, “(1)-³⁵Cl, (2)D”, “(1)-³⁵Cl, (3)D”, “(1)-³⁵Cl, (4)D”, “(1)-³⁵Cl, (1)-¹³C”, “(1)-³⁵Cl, (2)-¹³C”, “(1)-³⁵Cl, (3)-¹³C”, “(1)-³⁵Cl, (4)-¹³C”], one di[“(1)-³⁵Cl, (2,6)D₂,”] and one trisubstituted species [“(1)-³⁷Cl, (2,6)D₂”] have been investigated. From the moments of inertia of the vibrational ground state the r_s structure was derived. The reliability of the two small a coordinates could be enhanced through use of the multiply substituted species. The errors of the moments of inertia were propagated to the structural parameters. It could be shown that the benzene ring is deformed. However the quantitative deformation could not be established due to the rather large errors of some structural parameters.     

Ion chromatography of organic-rich natural waters from peatlands II. Na, NH4, K, Mg and Ca

Organic rich natural waters from peat bogs in continental (Switzerland) and maritime (Shetland Islands, Scotland) environments were analysed for Na⁺, NH₄⁺, K⁺, Mg²⁺ and Ca²⁺ using ion chromatography. These cations were determined simultaneously in surface and pore water samples from the continental bogs using a 250-μl injection loop in an isocratic separation. Using this loop, detection limits of the order of 1 ng/g were achieved. An organics-removal cartridge (Dionex OnGuard P) was used to remove humic materials. Analyses of deionized water filtered through these cartridges showed acceptably low blank values (e.g., ca. 5 ng/g) and appeared to have no significant effect on the measured cation concentration. For the maritime bog waters, the low concentrations of NH₄⁺ (ca. 1 μg/g) compared with Na⁺ (ca. 100 μg/g) required improved peak separation. This was accomplished using a gradient separation beginning with 40 mM HCl—1 mM , -2,3-diaminopropionic acid monochloride (DAP) and switching to 40 mM HCl-12 mM DAP after 2 min. Using a 25 μl injection loop, Na⁺, NH₄⁺, K⁺, Mg²⁺ and Ca²⁺ were determined simultaneously in less than 25 min. In this instance, even with Na⁺/NH₄⁺ > 100, there was no interference from Na⁺ in the determination of NH₄⁺ (baseline separated).     

生物组织中丝氨酸对映体的毛细管电泳-非接触式电导分离检测

采用高效毛细管电泳-非接触电导检测法, 使用未涂层石英毛细管(50 μm i.d.×45 cm, L_eff=40 cm), 以3.2 mmol/L氢氧化钠+0.4 mmol/L柠檬酸+2.5 mmol/L乙酸铜+5.0 mmol/L L-精氨酸+15.0 mg/L 羟丙基甲基纤维素为电泳运行液, 实现了未衍生化的D,L-丝氨酸对映体的基线分离和检测. 其线性范围为0.35~30 mg/L, 检出限(S/N=3)为0.10 mg/L. 对影响分离度的因素如手性选择剂、 电泳运行液的组成和浓度、 分离电压和进样方式等进行了探讨. 结果表明, 该方法无需衍生化预处理, 高效低耗, 可实现常见氨基酸共存组分的不干扰测定, 能有效测定小鼠脑组织样品中的D-丝氨酸含量.     

The (twin) composition plane as an extended defect and structure-building entity in crystals

The burden of this paper is the recognition of the composition plane as an extended (planar) “defect” in twinned crystals, together with the notion that new structure types may be generated from simple prototype structures by regular and frequent repetition of a twinning operation, usually on a very fine scale. Less regular application of the operation leads to disorder and variation in stoichiometry, without point defects being necessary.

The range of compounds whose structures may be described in these terms is very wide, from metal alloys through metal carbides and borides etc. and inorganic materials, such as metal oxides and sulphides, to minerals, including silicates and the “sulphosalts” of the heavy metals (Pb, Bi etc.). Isostructural compounds frequently span this whole gamut of substances.

The main reasons for the twinning appear to be () the generation of new types of interstices (not present in the prototype) of appropriate size for some of the constituent atoms, and/or (b) a variation in the concentration of appropriate interstices, i.e. in the stoichiometric ratio anion/cation.

After a general introduction to the relevant aspects of twinning, attention is successively concentrated on reflection-twinned h.c.p., then c.c.p. and finally mixed c.p. arrays: first with “interstitial” atoms only in the composition planes; and then with other interstices also occupied. In each case lamellar twinning is first considered, and then cyclic twinning. Glide-reflection-twinning of similar arrays is then considered.

Attention is also drawn to small topological distortions that, for example, convert the octahedra in a c.c.p. array (twinned or even un-twinned) to arrays of capped trigonal prisms (or to cubes). In this way the apparently complex structures of a number of compounds are derived from those of much simpler twinned c.c.p. arrays.

Finally, the not-very-large amount of available, relevant, experimental evidence is reviewed. As far as it goes, this confirms that the notion of the composition plane as an extended defect is well founded. But more experimental data are needed.

[In most cases specific literature references are provided for each structure. For a few, rather common, structures they are not. In such cases reference may be made to standard texts, e.g. for alloys, to Schubert⁹⁹ or Pearson¹³³ and, for more ionic structures, to Wyckoff¹³⁴ or Povarennykh¹³⁵. Diagrams are to scale: 1 cm = 4.0 Å.]     

Histidine as a dipolar eluent component in cation chromatography: II. Prediction of retention data for alkaline and alkaline-earth ions

The utility of cation chromatography has been developed by the application of -histidine as a multiprotic and dipolar (zwitterionic) eluent component. The method simplifies the cation analysis. The chromatographic characteristics of this system were studied in detail with a view to determining the selectivity and the mechanism by which the cations (Na⁺, K⁺, Mg²⁺, Ca²⁺) are retained. Complete separations were observed in the isocratic run over the eluent concentration range 3.0–6.0 mM at pH below 2.0. Sensitive detection was achieved using suppressed conductivity at the pH of isoelectric point of the histidine. Retention equations are derived for mono- and divalent cations eluted from ion-exchange separation column with multiple ionic eluents. The theory is based on the extension of ion-exchange equilibrium by protonation equilibria. The selectivity data for analyte and eluent species are determined using the model from the experimental retention data by computer-assisted iterative calculations. The model was utilized to predict retention data. The results in three-dimensional retention surfaces together with species distribution graphs are presented.     

Methods of calibration in the direct analysis of solid samples by electrothermal atomic absorption spectrometry

One of the major problems involved in the direct analysis of solid samples by electrothermal atomic absorption spectrometry (ETAAS) lies in the calibration step because non-spectral interference effects are often pronounced. Three standardization techniques have been described and used in solid sampling-ETAAS: (i) standard additions method; (ii) calibration relative to a certified reference material; and (iii) calibration curve technique. However, an adequate statistical evaluation of the uncertainty in the analyte concentration in the solid sample is most frequently neglected, and reported errors may be seriously underestimated. This can be attributed directly to the complexity of the statistical expressions required to accurately account for errors in each of the calibration techniques mentioned above, and the general lack of relevant reference literature. The object of this work has been to develop a computer package which will perform the necessary statistical analyses of solid sampling-ETAAS data; the result is the program “SOLIDS” described here in the form of an electronic publication in Spectrochimica Acta Electronica, the electronic section of Spectrochimica Acta Part B. The program could also be useful in other analytical fields where similar calibration methods are used. The hard copy text, outlining the calibration models and their associated errors, is accompanied by a diskette containing the program, some data files, and a manual. Use of the program is exemplified in the text, with some of the data files discussed included on the diskette which, together with the manual, should enable the reader to become familiarized with the operation of the program, and the results generated.     

Manipulation of separation selectivity of inorganic anions in electrostatic ion chromatography by the use of mixed cationic–zwitterionic micelles as the column coating solution

This paper describes an electrostatic ion chromatographic system in which the separation selectivity for inorganic anions, especially for sulfate and phosphate, could be manipulated by altering the molar ratio of the zwitterionic and cationic surfactants in the column coating solution used to prepare the stationary phase. The zwitterionic surfactant used for this study was 3-(N,N-dimethyltetradecylammonio)propanesulfonate (Zwittergent-3-14) and the cationic surfactant was tetradecyltrimethylammonium (TTA). Using a reversed-phase C₁₈ column (250×4.6 mm I.D.) coated with 10/10 (mM/mM) of TTA/Zwittergent-3-14 mixed micelles as the stationary phase and either NaHCO₃ or Na₂CO₃ aqueous solution as the eluent, together with suppressed conductivity detection, baseline separation of seven model inorganic anions was obtained. The elution order for those anions was found to be F⁻4²⁻−4²⁻2⁻−3⁻. Under the same conditions but using 1/10 (mM/mM) of TTA/Zwittergent-3-14 mixed micelles as the column coating solution, the elution order for these model ions was F⁻4²⁻4²⁻−2⁻−3⁻. The early elution of phosphate and sulfate is a unique attribute of this system. Detection limits for F⁻, HPO₄²⁻, Cl⁻, SO₄²⁻, NO₂⁻, Br⁻ and NO₃⁻ (S/N=3, sample injection volume 100 μl) were 0.11, 0.12, 0.12, 0.18, 0.49, 0.49, 0.52 μM, respectively.     

Acid-rain monitoring in East Asia with a portable-type ion-exclusion–cation-exchange chromatographic analyzer

A monitoring system consisting of a portable-type conductimetric ion-exclusion–cation-exchange chromatographic (CEC) analyzer and a meteorological satellite data analyzer has been investigated for the evaluation of the effects of acid precipitation on natural and urban environments in East Asia. The portable ion-exclusion–CEC analyzer uses a polymethacrylate-based weakly acidic cation-exchange resin column in the H⁺-form and a weak-acid eluent (tartaric acid–methanol–water) and is applied for the simultaneous determination of anions (SO₄²⁻, NO₃⁻, and Cl⁻) and cations (Na⁺, NH₄⁺, K⁺, Mg²⁺, and Ca²⁺) in precipitation transported from mainland China to central Japan, as mapped by the meteorological satellite data analyzer. Linear calibration graphs of peak area versus concentration for anions and cations were observed in the concentration range 0–1.0 mM for the anions and 0–0.5 mM for the cations. Detection limits at a signal-to-noise ratio of 3 were in the range 5.18–12.1 ppb for the anions and 6.58–16.5 ppb for the cations. The practical utility of this monitoring system is presented.     

Separation of metal ions by capillary electrophoresis

A number of experimental parameters have been optimized for the separation of 26 metal ions, including alkali, alkaline earth, transition and lanthanide metal ions. Experimental parameters that were evaluated included nature of indirect-detection reagent, pH of electrolyte, concentration of complexing agent and nature of the surface of the capillary; unbonded and C₁ and C₁₈ bonded phases were studied. In addition the effect of internal diameter on linearity and signal-to-noise ratio was examined, and separation efficiency was determined for a variety of experimental conditions. Detection limits (signal-to-noise RATIO = 3) were ca. 1 μg/ml for the lanthanides, ca. 0.6 μg/ml for transition and alkaline earth ions and ca. 0.1–0.8 μg/ml for alkali metal ions. The average relative standard deviations of were 3.7, 5.1 and 2.5% on unbonded, C₁ and C₁₈ capillaries, respectively. Whereas conventional regression analysis suggested that the calibration curves were linear over the range of 1·10⁻⁵ to 4·10⁻⁴ mol/l, sensitivity plots showed that the results were actually linear to within 6% only over the range of 2.5·10⁻⁵ to 4·10⁻⁴ mol/l.     

Determination of divalent trace metals in natural waters by preconcentration on N,N,N′,N′-tetra(2-aminoethyl)ethylenediamine-silica followed by on-line ion chromatography

A method for the on-line preconcentration and chromatography of trace metals, e.g., Co, Ni, Cu, Zn, Cd and Pb, on N,N,N′,N′-tetra(2-aminoethyl)ethylenediamine-bonded silica is described. The preconcentrated metals were desorbed with 0.13 M tartrate, which allows direct separation on a cation-exchange chromatographic column. The metals separated were detected by postcolumn reaction with 4-(2-pyridylazo)resorcinol and measuring the absorbances at 500 nm. Linear calibration graphs were obtained over the range 1 · 10⁻⁸−3 · 10⁻⁶ M. The synthesis and characteristics of the chelated silica are described. The method was applied to the analysis of river and interstitial sediment waters.     

Moment Analysis in Non-Linear Frontal-Elution and Elution Chromatography

Analytical formulae are presented for the statistical moments of an output chromatographic curve for non-linear distribution isotherms at a very narrow feed band (“elution chromatography”). Non-linear “frontal-elution chromatography”, i.e., the case of a very wide feed band, is also considered. The analytical expressions characterize the position and the width of sorption and desorption boundaries of the output curve. The column length at which a constant configuration of the sorption (or desorption) boundary is attained is dependent in the curvature of the isotherm and on the plate height. The results have been confirmed experimentally.     

离子色谱法测定高氯、高钠油田回注水中的阴、阳离子及有机酸

建立了高氯、高钠油田回注水中痕量无机阴、阳离子和有机酸的离子色谱分析方法。对高钠基质中痕量阳离子的测定,选用IonPac CS12A分析柱、H2SO4溶液梯度淋洗、电导检测器检测;对高氯基质中阴离子及有机酸的测定,选用对OH-具有高选择性的高容量的IonPac AS11-HC柱、KOH梯度淋洗、电导检测器检测。在优化的梯度淋洗条件下,高氯或高钠的存在不影响痕量阴离子或阳离子的测定。该方法具有良好的线性(r=0.9926~0.9990)和精密度(测定组分峰面积的相对标准偏差(n=7)在8.0%以下),回收率     

Syntheses of heparin - like pentamers containing “opened” uronic acid moieties

The syntheses of four analogues of pentasaccharide Ia, which corresponds to the minimal AT III binding region of heparin, are presented and the biological activities of these analogues will be discussed. Three of these analogues (i.e. compounds II, III and IV) contain an R-glyceric acid oxymethylene residue (i.e. B in fig.3) instead of -L-iduronic acid and in the other analogue (i.e. compound V) the β-D-glucuronic acid unit has been replaced by an s-glyceric acid oxymethylene residue (i.e. A in fig3). The R and S-glyceric acid oxymethylene residues represent an “opened” iduronic acid unit and an “opened” glucuronic acid unit, respectively, containing the essential carboxylate function in the appropriate configuration. The crucial step in the syntheses of these “opened” uronic acid pentamer analogues, was the preparation of the required glyceric acid oxymethylene residues 8a, 8b and 8c.

Analogues II and III, containing an “opened” iduronic acid moiety, display a significant AT III mediated Xa activity. Compound III contains two extra sulphate groups at unit 2. Removal of the contributing O-sulphate groups at position 3 and 6 of unit 6 of compound II (i.e. compound IV) results in a seven-fold drop in Xa activity. Replacement of the β-D-glucuronic acid unit by an S-glyceric acid oxymethylene residue (i.e. compound V) leads to almost a complete loss of Xa activity, notwithstanding the fact that all the essential and contributing charged groups are present in the molecule.