离子色谱法测定饮料中6种可溶性阴离子

建立离子色谱法测定饮料中6种可溶性阴离子。采用膜分离、抽滤离心、固相萃取柱、惰性气体吹扫方式进行样品处理。以2.4 mmol/L Na₂CO₃-1 mmol/L NaHCO₃溶液为淋洗液，经SHY-A-6色谱柱(250 mm×4.0 mm)分离，流量为1.0 mL/min，进样体积为50μL。氟离子、溴离子、亚硝酸根离子的质量浓度在0.00～2.00 mg/L范围内，硝酸根离子的质量浓度在0.00～20.0 mg/L范围内，氯离子、硫酸根离子的质量浓度在0.00～40.0 mg/L范围内与色谱峰高具有良好的线性关系，相关系数均不小于0.999 5，方法检出限为0.000 8～0.003 8 mg/L。样品加标回收率为100.6%～103.2%，平行测定结果的相对标准偏差为0.22%～0.87%(n=6)。该方法快速、稳定、选择性好，适用于检测饮料中可溶性阴离子。     

纸基过氯乙烯树脂微流控亚硝酸根离子检测片的研制

基于滤纸上过氯乙烯树脂栏选择性通过亚硝酸根离子, 结合微流控分析装置设计, 研制成纸基过氯乙烯树脂微流控亚硝酸根离子检测芯片. 采用该微流控亚硝酸根离子检测芯片测定了亚硝酸盐样品, 线性范围和检测限分别为70～1500 μmol/L 和48 μmol/L. 该微流控亚硝酸根离子检测芯片已成功应用于水样和食品中亚硝酸盐测定, 结果满意.     

离子色谱法测定烟气脱硫海水中的亚硫酸根离子

建立了燃煤电厂烟气脱硫海水中亚硫酸根(SO2~3)的离子色谱-脉冲安培检测方法。色谱柱为IonPac AS14A阴离子交换柱,流动相为14 mmol/L NaOH-12 mmol/L Na2CO3溶液(pH 11.7),流速1.2 mL/min,脉冲安培法检测。因SO2~3易被氧化,故在采样时加入甲醛作为保护剂,使之稳定存在。在测定海水样品前,用NaOH溶液(pH 12.0)沉淀海水中的Mg2+,以避免其在pH较高的流动相中生成沉淀堵塞色谱柱。采用该方法检测SO2~3的线性范围为0～100 mg/L,平均回收率为116.8%,检出限为0.05 mg/L;对7.5,25.0和75.0 mg/L的海水基底加标溶液分别进行9次平行测定,其相对标准偏差(RSD)分别为2.1%,3.1%和4.0%。该方法具有快速、灵敏、选择性好等特点,用于烟气脱硫的海水中SO2~3的检测,可得到令人满意的结果。     

抑制型离子色谱法检测植物样品中植酸根及磷酸根的含量

采用抑制型高效离子色谱法检测植物样品中植酸根和磷酸根的含量。样品用1%(质量分数)三氯乙酸处理,离心沉降 后取上清液经0.45 μm微孔滤膜过滤后注入离子色谱仪。用0.22 mol/L氢氧化钠水溶液、水和50%(体积分数)异丙醇水 溶液进行梯度淋洗,经微膜抑制后检测其电导率。实验结果表明,植酸根与磷酸根的检测不受F-、Cl-、SO2-4、NO-3、CC l3CO-2等阴离子的干扰。植酸根、磷酸根的质量浓度分别为5~400 mg/L和5~500 mg/L 时与峰面积呈良好的线性关系(r2分别为0.9994和0.9999),检出限分别为3.5 mg/L和1.5 mg/L;植酸根、磷酸根的平均 回收率分别为99.8%和98.4%,检测结果的相对标准偏差分别为1.98%和2.09%。     

离子色谱法检测牙膏中的亚硫酸盐

建立测定牙膏中亚硫酸盐的离子色谱法。采用Thermo Fisher Ion Pac AS11–HC和AG11–HC色谱柱,在11 mmol/L KOH溶液中分离测定牙膏中的亚硫酸根离子,亚硫酸根离子的质量浓度与色谱峰面积线性关系良好,线性方程为y=0.114 7x–0.012 3,相关系数r2=0.999 7,检测限为0.025 mg/L,测定结果的相对标准偏差为为2.2%(n=7),回收率在81.8%~90.3%之间。     

离子色谱法测量硝酸根和亚硝酸根国际比对研究

采用离子色谱法对1g/kg量级水平上CCQM-K59国际比对样品中的硝酸根和亚硝酸根校准溶液进行了准确测定。为进一步降低测定结果的不确定度、获得较高的准确度,以高纯硝酸钾和亚硝酸钠配置标准溶液。采用离子色谱法和电感耦合等离子体质谱法,分别对高纯硝酸钾和亚硝酸钠试剂中的主要阴离子和无机元素杂质进行了测定,采用归一化法扣除测定杂质,获得了准确的纯度值。在配置标准溶液时,对固体样品的称量进行了浮力修正;采用单点校准法测量国际比对样品中硝酸根和亚硝酸根的含量,以括号法校正仪器漂移。比对样品中硝酸根和亚硝酸根的含量分别为1.0172 g/kg和1.0139 g/kg,测定结果的相对扩展不确定度分别为0.11%和0.13%,获得了良好的国际等效一致性,在源头上保证了我国硝酸根和亚硝酸根检测领域的量值溯源。     

固相萃取–离子色谱法测定人尿液中钙、镁、氟、磷酸根离子

建立固相萃取–离子色谱法测定人尿液中钙、镁两种阳离子和氟、磷酸根两种阴离子。采用C₁₈固相萃取柱去除样品中杂质以消除干扰,以CS12 A型阳离子交换柱为分离柱,以甲基磺酸溶液为淋洗液,等度洗脱,测定钙、镁离子;以AS15型阴离子交换柱为分离柱,以KOH溶液为淋洗液,梯度洗脱,测定氟、磷酸根离子。钙、镁离子的质量浓度在0.25～10 mg/L范围内,氟、磷酸根离子的质量浓度分别在0.002 5～0.05 mg/L、1.25～50 mg/L范围内与色谱峰面积具有良好的线性关系,相关系数均大于0.999 0,方法检出限为0.002～0.2 mg/L。样品加标回收率为86.0%～99.5%,测定结果的相对标准偏差为0.12%～5.50%(n=6)。该方法操作简便,灵敏度高。     

离子色谱法测定醇胺脱硫溶液中热稳定盐

为了控制热稳定盐(HSS)对天然气净化装置造成的危害,建立了一种同时检测醇胺脱硫溶液中的乙酸根离子、甲酸根离子、氯离子、硫酸根离子、草酸根离子、硫代硫酸根离子和硫氰酸根离子的离子色谱方法。该方法利用膜过滤、反相固相萃取和稀释3个步骤对工业样品进行前处理,采用氢氧化钾梯度淋洗和电导检测的方式,实现了7种离子的分离与检测。方法的线性范围为0.01～0.5 mmol/L,检出限(以信噪比(S/N)为3计)小于0.1 mg/L,回收率为80.0%～100.3%。在5个不同添加浓度下分别测定了上述7个离子,色谱峰面积的重复性良好(相对标准偏差(RSD, n=10)为0.94%～3.99%。通过3个实验室比对试验,表明该方法再现性良好,色谱峰面积的RSD小于5%。应用该方法成功地检测了8家天然气净化厂、3家石油炼厂和1家煤制油工厂的脱硫溶液样品中的HSS,并连续监测某天然气净化装置15 d。该方法具有良好的可靠性和实用性。     

2-氨-6-氯嘌呤用于亚硝酸根离子的荧光光度法测定

应用荧光光谱法研究了2-氨-6-氯嘌呤与亚硝酸根离子间的相互作用并建立了亚硝酸根离子测定的新方法.在0.25 mol/L的H2SO4水溶液中,2-氨-6-氯嘌呤分子上的氨基与亚硝酸根离子发生重氮化反应生成重氮盐,重氮盐在沸水浴中加热水解,氨基被羟基取代,产生弱荧光的2-羟基-6-氯嘌呤.此反应导致荧光强度降低且在一定范围内与亚硝酸根离子浓度呈良好的线性关系,据此建立了荧光猝灭法测定亚硝酸根离子的新方法,其线性范围为1.00×10-7 ～1.30×10-5 mol/L,方法检出限为7.54×10-8 mol/L.该方法应用于自来水中亚硝酸根离子的测定,回收率为102% ～110%.     

二维离子色谱法测定海水中的铵离子

研究了二维离子色谱测定海水中铵离子的方法。海水样品经10倍稀释,一维色谱采用高容量的CS–165 mm柱,以30 mmol/L甲磺酸溶液等度淋洗,流量为1 m L/min,进样25μL,CSRS–300 4 mm抑制电导分离Na+,NH4+;二维色谱采用CS–12A 4 mm柱,以8 mmol/L甲磺酸溶液等度淋洗,流量为1 m L/min,以1 300μL定量环进样,SC–CSRS–300盐转换器抑制电导检测NH4+。结果表明:色谱峰面积与NH4+质量浓度线性相关,相关系数为0.999 9。10μg/L标准溶液测定结果的相对标准偏差为2.7%(n=7),NH4+的方法检出限和仪器检出限分别为0.42,0.05μg/L,海水中NH4+加标回收率为80.8%~105.8%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.