羟乙基纤维素醋酸酯热致液晶性和相转变

本文研究了羟乙基纤维素醋酸酯的热致液晶和相转变过程。发现升温时,在130～185℃范围内羟乙基纤维素醋酸是各向异性的熔体,在温度高于185℃以后是各向同性的熔体。降温时,各向异性相在165℃时开始形成,进一步冷却到室温,形成液晶玻璃态。在降温过程中,相转变和液晶相织构的形成都很快,而且一旦液晶相的织构形成以后就不再随时间和温度降低而变化。羟乙基纤维素醋酸酯的热致液晶性还受其分子量影响,分子量越高,相转变温度越高。但是,在适当的分子量下,羟乙基纤维素醋酸酯才有最大的动力学相转变能力。     

甲基纤维素/二氯乙酸液晶溶液的相转变

本文研究了甲基纤维素/二氯乙酸液晶溶液液晶相与各向同性相之间相互转变的过程。在连续升温过程中,由于液晶相内部有序度的非均一性,升温速率对液晶相织构随温度的变化有较大的影响。在等温相转变过程中,无论是从各向同性态转变为液晶态,还是其逆过程,从液晶态转变为各向同性态,相转变曲线均具有指数方程特征。利用与 Avrami 方程相似的指数方程进行处理,在从各向同性态转变为液晶态时,指数 n 大部分约为1。但液晶相向各向同性相在低于 Tc 时的相转变中,n 均小于1。相转变速率受溶液浓度和温度的影响。在质量分数为0.259的浓度时,液晶相向各向同性相的转变在低于 Tc 时39.5℃进行得最快。     

氰乙基纤维素/二甲基乙酰胺液晶溶液的研究

本文利用 Abbe'折射仪和热台偏光显微镜研究了氰乙基纤维素/二甲基乙酰胺液晶溶液的形成、结构和某些性质。它与许多溶致性液晶一样,随溶液浓度的增加,溶液从各向同性状态经过两相共存状态转变成为单一的液晶态。溶液的双折射△n 随浓度增加而增加,随温度的升高而降低。升温速率的改变对测定临界温度值有一定的影响。液晶相在无外力作用时由许多取向的、无规分布的微区域组成。受到切应力后,微区变成长条状。分子链沿切应力方向取向,并在垂直于切应力方向上在各微区域内排列有序,相邻两微区的分子链的取向方向稍有不同。     

氰乙基纤维素/二甲基甲酰胺液晶溶液的流变行为

本文通过测定不同浓度的溶液在不同温度和切变速率下的粘度,讨论了氰乙基纤维素/二甲基甲酰胺溶液的流变行为。溶液的流动曲线表明,该溶液是一种假塑性液体。在浓度较高时,存在屈服现象,屈服应力的大小与浓度和温度有关。溶液的浓度—粘度曲线表示出典型的液晶行为。粘度与浓度的关系和屈服应力与浓度的关系相似。溶液的临界浓度随温度的升高而增加。在单相区(各向同性相或液晶相),粘度随温度升高而降低,表观流动活化能大于零。但在两相区,粘度随温度的升高而增大,表观流动活化能小于零。该实验得到的临界浓度与通过光学的方法所得的临界浓度是一致的。     

乙基醋酸纤维素液晶相织构的温度依赖性

本文利用热台偏光显微镜观察了在不同温度下乙基醋酸纤维素/二氯乙酸液晶溶液中液晶相的双折射纹理织构的变化。证明液晶相中分子链排列的有序程度不是完全相同的。在一定的升温速率下加热溶液,有序程度较低的部份首先被破坏。升温速率足够慢时,较高温度虽然使液晶聚集体缩小,但在液晶相内,分子键排列的有序程度不会降低,有时甚至还会增加。从各向同性溶液转变为液晶溶液时,液晶相首先形成圆盘织构。在两相共存的溶液中,分散相都尽可能以圆形存在于连续相中,以降低体系能量。     

氰乙基纤维素/二甲基乙酰胺液晶溶液的研究

本文利用Abbe折射仪,热台偏光显微镜,小角光散射等方法研究了氰乙基纤维素/二甲基乙酰胺液晶溶液的形成,形态结构和某些性质。溶液随浓度的增加,从各向同性态经过两相共存状态,转变成为单一的液晶态。该液晶是胆甾型的。溶液的双折射Δn随浓度的增加或温度的降低而增大。在无外力作用时,液晶相由许多无规分布的取向微区组成。液晶溶液受切应力后形成“条纹结构”,大分子链沿切应力方向取向,并在各条纹中排列有序。     

一个判别液晶聚合物状态的新方法

伴随液晶相转变而产生的转变焓、转变熵可提供有关各相的结构、状态及有序度等信息.本文从动力学、热力学角度分析了液晶聚合物从各向同性熔体冷却时系统的热熵变化,建立了液晶聚合物升降温过程中的热熵图,提出了定量判断液晶聚合物从各向同性熔体冷却后所处状态的新方法.     

乙基醋酸纤维素溶致性液晶的研究

乙基醋酸纤维素溶于三氟乙酸、二氯乙酸、醋酸中.在浓度大于临界浓度时,形成胆甾型液晶态.溶液随浓度的增加,从各向同性态经两相共存转变成液晶态.在加热液晶溶液时,溶液转变成各向同性态.降低温度,液晶相再生成.在形成液晶过程中,存在过冷现象.在一定的条件下,液晶相以球状的形式存在.溶液的双折射△n在两相共存与完全液晶态间相互转变时会发生较大变化.乙基醋酸纤维素大分子链的刚性随有机酸溶剂体系的酸强度的增大而增大,使临界浓度C_1~*随溶剂酸强度的增大而减小.     

乙基醋酸纤维素溶致性液晶的研究

非全取代的乙基纤维素在浓硫酸催化下与醋酸反应,生成乙基醋酸纤维素。乙基醋酸纤维素在适当的条件下可以形成溶致性液晶。随浓度的升高,溶液从各向同性态经两相共存,转变成完全的液晶态。在加热溶液时,可以看到两相共存状态的形成和液晶相的完全消失,降低温度,液晶相又可以再生成。在液晶相生成的过程中,存在过冷现象,液晶聚集的区域由许多微小的取向区域组成,它们的取向方向不相同。溶液的n—c曲线在各相同性、两相共存和液晶态区域内是直线,但在这些相态之间相互转变时出现转折点。溶液的双折射△n=ne—no在两相共存与液晶态相互转变时也会发生较大变化。乙基醋酸纤维素大分子链的刚性随有机酸溶剂体系的酸的强度增大而增大,使临界浓度C_1~*随溶剂酸的强度的增大而减小。     

热致型液晶聚合物的晶化动力学

本文探讨了液晶聚合物的结晶与液晶相转变动力学机理。通过不同温度下液晶化与结晶化过程的Avrami指数与生长速率的变化,提出了各聚合物液晶生长和结晶生长所可能采取的方式。此外,还对一些液晶聚合物结晶时形成的球晶进行了分析和讨论。     

SeTe8Sb1非晶合金的玻璃转变

The process of glass transition on the non-crystal SeTe_8Sb_1 has been researched using low temperature differential scanning calorimetry (DSC). The following conclusions are deduced: this process is a second-order phase transformation, the stronger endotherm displayed in it is imputed to hysteresis of the transition. The temperature of glass transition in heating process decrease with reduction of the cooling rate while forming glass. The activation energy of glass transition quickly increases from 174 kJ·mol. (at quenching rate ~10~4 K·min~(-1)) to 399 kJ·mol~(-1). (at cooling rate ~10 K·min~(-1)) So that the glass obtained at lower cooling rate is more stable than that obtained at higher rate.     

PROPERTIES OF A NEW STATE OF HEMATOPORPHYRIN IN DILUTE AQUEOUS SOLUTION

Abstract —Dilute aqueous hematoporphyrin undergoes a transformation after standing at room temperature leading to a shift of the Soret peak from 395 nm to 405 nm, disappearance of visible bands I (610 nm) and IV (503 nm), a shift of the first emission band from 615 nm to 580 nm, and fluorescence polarization at room temperature. The transformation was accelerated by heating and was faster for more dilute solutions. It did not take place in ethanol, 99:1 glycerol-water, or in small egg lecithin liposomes. It was rapid in SDS micelles and did not occur in CTAB and Triton X-100 micelles. Low concentrations of divalent zinc and copper increased the rate of transformation, but the product was not the corresponding metal ion ligand. The transformation was fast with uroporphyrin I and fast but incomplete with hematoporphyrin derivative. The methyl esters of hematoporphyrin IX and uroporphyrin I did not transform. The tentative identification of the transformed product is a tightly-bound linear micelle, oriented such that the central hydrogens of the free base monomer units are anti-parallel.     

非等温结晶对PLLA的热行为和形貌的影响

将聚L-乳酸(PLLA)熔化非等温熔融结晶, 采用DSC、POM、SEM等技术研究了降温速率对PLLA的热行为和形貌的影响. PLLA在低降温速率(2 ℃·min-1)下的结晶在118 ℃伴随有结晶机制的转变. 玻璃化温度和结晶度随着降温速率的降低而增大. 随着降温速率的降低, 球晶尺寸增大, 当降温速率为10 ℃·min-1 时, PLLA 为无定型材料. 采用模压成型的方法并控制降温速率制备了具有球晶结构的条状PLLA 生物材料, 与高降温速率下制备的PLLA相比,低降温速率下获得的具有球晶结构的PLLA材料的断面更光滑和致密, 但脆性增强.     

DSC测试中样品内部的温度分布及其对比热测试的影响

由傅里叶导热定律结合Tools-Narayanaswamy-Moynihan(TNM)松弛模型提出了一种计算聚合物样品内温度分布的方法.对PS的计算结果表明温度梯度随样品厚度、升温速率增大而增大,对于1.0 mm的PS以1 K/min降温后再以10 K/min升温时样品内部最大温差为0.882 K.在此基础上提出了不同样品厚度、不同热处理条件下聚合物测定比热的计算方法,结果表明计算结果与实测数据基本一致.     

聚丙烯-g-聚氨酯共聚物的非等温结晶动力学研究

用DSC法研究了聚丙烯 (PP)和聚丙烯接枝聚氨酯的共聚物 (PP g PU)在不同冷却速率下的非等温结晶动力学 .用Avrami方程和莫志深改进法对DSC测定结果进行了处理 ,结果表明 ,PP g PU的动力学参数能很好的符合Avrami方程和莫志深改进方程 .PP接枝了聚氨酯支链后 ,结晶速率增大 ,球晶的生长和成核机制也相应发生改变 ,而其变化规律与接枝物的组成和结构密切相关     

Characterization and phase transformation study of TlSbSe2 crystals

TlSbSe₂ monocrystals were grown using the modified Bridgman–Stockbarger method and were characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). Reflectivity spectra have been registered in the range 50 to 4000 cm^–1 for E parallel to a and E parallel to b polarizations, on the cleavage plane. A remarkable anisotropy at two directions was verified. With regard to previous observations, additional peaks were discriminated and the fundamental phonon parameters were determined using classical dispersion relations. The material presents a complex phase transformation – with two thermal effects – that was examined using differential scanning calorimetry (DSC). Non-isothermal measurements, at different heating and cooling rates (β), were used to study the thermal phenomena. The main effect is attributed to a structural displacement and the second one to a cation exchange procedure. The phase transformation temperature depends strongly on the cooling rate and the peaks are shifted by 30 K with the increase of this rate, on the contrary to the increase of the heating rate that has a smaller effect. Phenomena related with the influence of the previous, repeated heating and cooling cycles on the transformation are also examined and analytically discussed.     

EFFECT OF N,N,N’,N’-TETRAALKYL TEREPHTHALAMIDE ON NON-ISOTHERMAL CRYSTALLIZATION KINETICS OF POLYPROPYLENE

The effect of N,N,N＇,N＇-tetraalkyl terephthalamide （TATA） on the non-isothermal crystallization and melting characteristics ofpolypropylene （PP） was studied. The addition of TATA can lead to the formation ofβ-crystal PP. With the increase in TATA concentration the degree of crystallinity for β-crystal PP increased significantly, and that for a-crystal PP decreased, which indicated that TATA effectively induced the formation of β-crystal PP. WAXD also revealed the existence of β-crystal PP after the introduction of TATA into PP. PP containing TATA crystallized at a temperature range of 5-10℃ higher than that of pure PP, and the half-crystallization time （t1/2） and Avrami exponent （n） of PP at the same cooling rate were decreased by the addition of TATA, indicating that TATA influenced the crystallization rate and crystallization growth mode of PP. The rate constant of crystallization of PP containing TATA （Zc） was larger than that of pure PP, which further indicated that the crystallization of PP was accelerated by the addition of TATA.     

Optimum heat treatment conditions for masking the bitterness of the clarithromycin wax matrix

The effects of the contents of aminoalkyl methacrylate copolymer E (AMCE) in a wax matrix on the mechanism of polymorphic transformation of glyceryl monostearate (GM) were clarified by evaluating the enthalpy change defined as 1.51 (DeltaH(1)-DeltaH(2))/DeltaH(2), where DeltaH(1) and DeltaH(2) denote the enthalpies in the first and second thermal analyses, respectively. Using this value, K(1), the rate constant of transformation from alpha-form to beta'-form, and K(2), the rate constant of transformation from beta'-form to beta-form, could be obtained. As the ratio of AMCE increased, K(2) increased, but a minimum point existed for K(1). K(1) was always larger than K(2), but gradually approached K(2) as the ratio of AMCE increased. The optimum temperature for the transformation of GM was 50 degrees C, at which the enthalpy change was maximum. To prepare the wax matrix preparation of clarithromycin (CAM), we considered 40 degrees C the optimum treatment temperature for the transformation of GM in a CAM wax matrix compounded from CAM, GM and AMCE, since the matrices were mutually welded at above 45 degrees C during the spray congealing process. Although K(1) and K(2) were almost the same at 40 degrees C, the rate of transformation was accelerated by tumbling. By applying the tumbling that accelerated the transformation of GM in a CAM wax matrix, almost all of the alpha-form disappeared, and the release of CAM from the wax matrix diminished when the enthalpy change was more than 0.8.     

间规聚苯乙烯同质多晶现象的研究

间规聚苯乙烯(ｓＰＳ)是由日本出光公司在1985年首先合成,由于其优良的耐热性(熔点高达270℃),立刻被认为有可能或为下一世纪最重要的工程塑料.独特的分子结构,使间规聚苯乙烯具有密度低、尺寸稳定、耐热性、耐溶剂性好等诸多优点,因而引起研究人员的广泛重视.同时,间规聚苯乙烯存在复杂的同质多晶现象,共有α、β、γ和δ四种晶型.以不同的条件从熔体结晶,间规聚苯乙烯可形成平面锯齿结构的α晶和β晶.其中,α晶属六方晶系,晶胞参数为:ａ=263ｎｍ,ｃ=078ｎｍ;β晶是斜方晶,晶胞参数为:ａ=088ｎｍ,ｂ=263ｎｍ,ｃ=078ｎｍ.与传统的全同聚丙烯…