Novel fabrication of magnetic thermoplastic nanofibers via melt extrusion of immiscible blends

A novel technique of fabricating magnetic thermoplastic nanofibers by the control of the phase separation of immiscible polymer blends during melt extrusion was presented. The magnetic poly(vinyl alcohol‐co‐ethylene) (PVA‐co‐PE)/Fe₃O₄ composite nanofibers were prepared via the melt extrusion of cellulose acetate butyrate matrix and PVA‐co‐PE preloaded with different amounts of Fe₃O₄ nanoparticles. The morphologies of magnetic composite nanofibers were characterized by scanning electron microscopy. The uniform dispersion of Fe₃O₄ nanoparticles in nanofiber matrixes and crystal structures were confirmed using transmission electron microscopy and wide angle X‐ray diffraction. Thermogravimetric analysis was employed to quantify the exact loading amount of Fe₃O₄ nanoparticles in the composite nanofibers. The magnetic measurements showed that composite nanofibers displayed superparamagnetic behavior at room temperature. With increasing content of Fe₃O₄ nanoparticles, the saturation magnetization of the magnetic composite nanofiber significantly improved. The prepared magnetic composite nanofibers might have found potential applications in the sensors and bio‐molecular separation fields. Copyright © 2012 John Wiley & Sons, Ltd.     

In Situ Synthesis of a Supramolecular Hydrogelator at an Oil/Water Interface for Stabilization and Stimuli‐Induced Fusion of Microdroplets

Supramolecular hydrogels are expected to have applications as novel soft materials in various fields owing to their designable functional properties. Herein, we developed an in situ synthesis of supramolecular hydrogelators, which can trigger gelation of an aqueous solution without the need for temperature change. This was achieved by mixing two precursors, which induced the synthesis of a supramolecular gelator and its instantaneous self‐assembly into nanofibers. We then performed the in situ synthesis of this supramolecular gelator at an oil/water interface to produce nanofibers that covered the surfaces of the oil droplets (nanofiber‐stabilized oil droplets). External stimuli induced fusion of the droplets owing to disassembly of the gelator molecules. Finally, we demonstrated that this stimuli‐induced droplet fusion triggered a synthetic reaction within the droplets. This means that the confined nanofiber‐stabilized droplets can be utilized as stimuli‐responsive microreactors.     

Transition behaviors and hybrid nanofibers of poly(vinyl alcohol) and polyethylene glycol–POSS telechelic blends

We report solution properties of the blend solutions of poly(vinyl alcohol) (PVA) and poly(ethylene glycol) (PEG)–POSS telechelic and its corresponding hybrid nanofibers prepared by electrospinning. The morphologies, microstructures, and wettability of the resulting PVA/PEG3.4k–POSS hybrid nanofibers are studied. The morphologies of the resultant PVA/PEG3.4k–POSS nanofibers are regular with the fiber diameter ranging from 610 ± 110 to 810 ± 280 nm. When the content of PEG3.4k–POSS telechelic increases above 20 wt.%, the beaded fiber morphologies are observed due to severe aggregations of the PEG3.4k–POSS telechelics as well as increased viscosity at higher concentration. In addition, the solution properties of pure PEG3.4k–POSS telechelic solution (ca. 3–5 wt.%) and PVA/PEG3.4k–POSS solutions blended with PVA are explored, and found to show the reversible turbid-to-transparent transition behavior with respect to the solution temperature. Water contact angle measurement of the PVA/PEG3.4k–POSS nanofiber membranes demonstrates an enhanced hydrophobic nature due to the incorporated POSS moieties.     

Highly redispersible sugar beet nanofibers as reinforcement in bionanocomposites

A simple method for preparing redispersible nanofibers from sugar beet residue and their use as a well-dispersed reinforcement for a polyvinyl alcohol (PVA) matrix is reported. It is known that the redispersion of dried cellulose nanofibers is difficult because of the formation of strong hydrogen bonds between the nanofibers. The results show that the properties of the initial sugar beet nanofiber suspension can be recovered without the use of chemical modification or additives with higher pectin and hemicellulose content. Undried and redispersed nanofibers with and without pectin were used as nanocomposite reinforcement with PVA. The redispersed nanofibers were as good reinforcements as the undried nanofibers. The tensile strength and elastic modulus of the nanocomposites with the redispersed sugar beet nanofibers were as good as those of the nanocomposites with undried nanofibers. Interestingly, the nanofiber dispersion in the PVA matrix was better when sugar beet nanofibers containing pectin and hemicellulose were used as reinforcements.     

Stabilization of electrospun poly(vinyl alcohol) nanofibrous mats in aqueous solutions

<正>The stability ofpoly(vinyl alcohol)(PVA) nanofibrous mats in water media was improved by post-electrospinning treatments.Bifunctional glutaraldehyde(GA) in methanol was used as a crosslinking agent to stabilize PVA nanofiber,but fiber twinning was observed frequently,and the highly porous structure of PVA nanofibrous mats was destroyed when the crosslinked fiber was soaked in water.To overcome this shortcoming,chitosan(CS) was introduced into the PVA spinning solution to prepare PVA/CS composite nanofibers.Their treatment in GA/methanol solution could retain the fiber morphology of PVA/CS nanofibers and porous structure of PVA/CS nanofibrous mats even if they were soaked in aqueous solutions for 1 month.Scanning electron microscopy(SEM),X-ray diffraction(XRD),thermal gravimetric analysis(TGA) and differential scanning calorimetry(DSC) were applied to characterize the physicochemical structure and thermal properties of PVA nanofibers.It was found that the water resistance of PVA nanofibrous mats was enhanced because of the improvement of the degree of crosslinking and crystallinity in the electrospun PVA fibers after soaking in GA/methanol solution.     

Fabrication,characterization and in vivo evaluation of dexpanthenol sustained-release nanofibers for wound healing

In this study, wound dressings consisting of dexpanthenol (Dex)-loaded electrospun nanofibers were fabricated using polyvinyl alcohol (PVA)/sodium alginate (SA), and chitosan as the core and the shell, respectively. Considering the remarkable properties of chitosan, it was used as a shell against drug release and to improve the thermal stability, and tensile strength of the scaffold. By comparing the thermogravimetric, and tensile strength results of nanofibers with and without shell, it was revealed that the presence of chitosan in the shell side could improve the thermal stability and increased the tensile strength by about three times. The isotherm models of dexpanthenol release from the PVA/SA/Dex-CS scaffold was best described by the Langmuir model. Besides, Fourier transform infrared, scanning electron microscopy, and X-ray diffraction techniques were performed to characterize nanofibers. Furthermore, an in vivo investigation of a wound dressing with dexpanthenol showed better healing compared to the wound dressings without dexpanthenol.     

Electrospinning fabrication and characterization of poly(vinyl alcohol)/montmorillonite/silver hybrid nanofibers for antibacterial applications

Poly(vinyl alcohol) (PVA)/montmorillonite clay (MMT)/silver (Ag) nanoparticles have been electrospun for fabricating PVA/MMT/Ag nanofiber in aqueous solutions. Since PVA is a water-soluble and biocompatible polymer, it is one of the best materials for preparation of antibacterial nanofiber. MMT has been used as an inorganic filler to enhance properties of homopolymeric nanofiber. The PVA/MMT/Ag nanofiber diameter increases with increasing contents of MMT clay and Ag nanoparticles. In preservation test, the PVA/MMT/Ag nanofiber confirms an excellent antibacterial performance, elucidating for practical uses as a new preservative. Moreover, the PVA/MMT/Ag nanofiber shows improved thermal properties.     

Fabrication,characterization and X-band microwave absorption properties of PAni/Fe3O4/PVA nanofiber composites materials

This work presents a study of microwave absorption properties of PAni/Fe₃O₄/PVA nanofiber composites with different ratio of Fe₃O₄ nanoparticles. The morphology of the composites nanofibers study by Field Emission Scanning Electron Microscopes (FESEM) and Transmission Electron Microscope (TEM) showed that the low content of Fe₃O₄ nanoparticles presence in the composites nanofibers indicates very much uniform surface, in the composites nanofiber without many bends, but some bends develop at higher content of Fe₃O₄ nanoparticles as indicated in the TEM image. Image-J software was used to further investigate the diameter of the composites nanofiber and found to be in the range of 152 to 195 nm. The nanofiber composites show excellent electric and magnetic properties and therefore vary with the addition of Fe₃O₄ nanoparticles in the composites nanofiber. In addition the PAni/Fe₃O₄/PVA composites nanofibers were further characterized by X-ray diffraction spectra (XRD) and Four Transformation infrared spectra (FTIR). The XRD pattern shows the presence of PAni nanotubes containing Fe₃O₄ nanoparticles by indicating peaks at 23.4⁰ and 35.43⁰ which was further supported by FTIR analysis. Microwave vector network analyzers (MVNA) were used to estimate the microwave absorption properties of the composites nanofibers. The absorption parameters was found to be −6.4 dB at 12.9 GHz within the range of X-band microwave absorption frequency, this reflection loss is attributed to the multiple absorption mechanisms as a result of the improved of impedance matching between dielectric and magnetic loss of the absorbent materials demonstrating that these materials can be used as protective material for electromagnetic radiation.     

PVA改性PAMPS-PAM超高力学性能双网络水凝胶的制备

采用紫外光引发聚合制备了聚乙烯醇(PVA)改性的聚(2-丙烯酰胺基-2-甲基丙磺酸)-聚丙烯酰胺(PAMPS-PAM)双网络(DN)水凝胶.测定并比较了PVA改性前后PAMPS-PAM双网络水凝胶的溶胀动力学;通过扫描电子显微镜(SEM)观察了单网络水凝胶的结构;测定PVA改性前后PAMPS-PAM双网络水凝胶的压缩及拉伸性能.结果表明,经PVA改性后的PAMPS-PAM双网络水凝胶有较高的溶胀比;0.82%PVA用量的PAMPS-PAM双网络水凝胶在90%压缩形变率下仍保持完整、最大拉伸应力达到0.5 MPa,大幅提高PAMPS-PAM双网络水凝胶的力学性能.     

疏水性聚丙烯酸/聚乙烯醇/葡萄糖淀粉酶复合纳米纤维膜的制备及酶学性质

利用混合静电纺丝将葡萄糖淀粉酶(GA)固定于聚丙烯酸(PAA)/聚乙烯醇(PVA)纳米纤维膜上,并通过鉴定固定化GA的酶学特征检验PAA/PVA可否成为一种优良的酶固定化载体。 对其理化性质和酶学特征进行鉴定,经红外光谱(FT-IR)和扫描电子显微镜(SEM)表征发现,GA可成功包埋于PAA/PVA纳米纤维膜内部;对包裹固定的GA进行酶学性质鉴定,发现固定化GA的最适反应温度为68 ℃,比游离GA提高了9 ℃;固定化GA的适用pH值范围明显变宽;热稳定性和存贮稳定性显著增强且可以重复使用。PAA/PVA纳米纤维膜是一种优良的酶固定化载体,可以通过混合静电纺丝包埋法简便地将蛋白质分子固定于其内部,具有一定的应用前景。     

CdHgTe纳米晶/聚乙烯醇近红外纳米纤维的制备

采用一步法制备了性质稳定的CdHgTe纳米晶, 将其与聚乙烯醇水溶液共混, 通过静电纺丝方法获得了CdHgTe纳米晶/聚乙烯醇纳米纤维. 改变聚乙烯醇水溶液的浓度可以使纤维的直径在200~400 nm范围内可调. 所制备的纳米纤维在近红外区域具有很强的荧光, 而且发光峰位与原水相纳米晶的峰位基本一致, 这是采用其它方法制备纳米晶与聚合物的复合材料难以实现的. 通过与聚乙烯醇的复合, 纳米晶的热稳定性得到进一步增强, 在120 ℃下将纳米纤维加热2 h, 其形貌和发光性质都未发生明显的变化.     

细菌纤维素(BC)增强PVA/PVP复合水凝胶的制备及性能表征

通过冷冻-熔融法制备了细菌纤维素/聚乙烯醇/聚乙烯吡咯烷酮(BC/PVA/PVP)双网络复合水凝胶,并采用X射线衍射,红外光谱,扫描电镜,力学性能测试等手段对凝胶的结构和性能进行表征.研究发现PVA、PVP通过氢键作用均匀地吸附于纤维微丝周围,将BC纤维有效地分开,因而干燥后的复合凝胶在热水中浸泡后仍可恢复原状;X射线...     

淀粉-丙烯酸钠接枝共聚物的固体高分辨核磁共振研究

运用固体高分辨核磁共振技术,通过测量13C魔角旋转/交叉极化(CP/MAS)谱、1H自旋-晶格弛豫时间T1及旋转坐标系中的自旋-晶格弛豫时间T1ρ,对一系列淀粉-丙烯酸钠接枝共聚物的相结构进行了研究,并与淀粉、均聚丙烯酸钠及两者共混物的实验结果进行了比较.结果表明,接枝共聚导致了淀粉结晶度的明显降低;在共混物和接枝共聚物中,淀粉和聚丙烯酸钠组分都具有纳米尺度的相容性,由于接枝的效应,接枝共聚物中两个组分表现出比共混物更高的相容水平.     

药物和蛋白质与聚己内酯分层复合纳米纤维的微观结构与力学特性

应用同轴共纺技术制得芯质和表层为两种不同材料的分层复合纳米纤维.分别以乙酰螺旋酶素片剂和明胶蛋白质为芯质材料,以可生物降解的聚己内酯作为表层材料,研究了这种分层复合纳米纤维的微观结构与力学特性.结果表明,尽管药物与表层聚合物材料的溶解溶剂互不相同,但仍可以将药物包覆在壁厚小于100nm的超细纤维中.这种纤维可用作体内手术伤口缝合线或大面积创伤如烧伤伤口的敷布.在实验范围内,纤维膜的力学性能随芯质内溶质含量的提高而降低.     

An investigation on polycaprolactone/chitosan/Fe3O4 nanofibrous composite used for hyperthermia

Hyperthermia is considered as an effective supplementary cancer treatment. However, the uneven temperature distribution is the major challenge in hyperthermia. Nanotechnology could solve this problem by applying magnetic nanoparticles directly or in nanofibers as implants. Low solubility, poor cancer targeting, and leakage are limitations of free magnetic nanoparticles. In this work, Fe₃O₄ nanoparticles were loaded into polycaprolactone/chitosan blended nanofibers in various contents. Magnetic, chemical, physical, and morphology of the derived nanofibrous composites were then studied. The results showed the magnetic properties of the nanocomposite had low coercivity, which was close to superparamagnetic particles. Chemical analysis showed that components had no interaction with each other. Nevertheless, Fe₃O₄ was slightly transformed to other iron oxides. However, the magnetic analysis showed this transformation had no significant effect on final magnetic content of the nanofibers. The results of X‐ray diffraction (XRD) (19.5 nm), transmittance electron microscopy (TEM) (21.6 nm), and vibration sample magnetometer (VSM) (17 nm) suggested that the magnetic nanoparticles were single domain. Thermal analysis results showed that 7% Fe₃O₄ nanofibers had more heat increase as oppose to other nanofibrous composites in the alternative magnetic field (AMF). Nonetheless, the heat performance of 3% Fe₃O₄ nanofibers was more than others according to its specific power absorption (SPA). Therefore, due to the importance of using nanoparticles in the least possible content, this method can be used as a postsurgical treatment by applying these nanofibrous composites as implants on the tumor site. Moreover, these nanofiber composites could carry anticancer drugs, which are applied as a multi‐mode treatment system.     

Characterization,mechanical, and antibacterial properties of nanofibers derived from olive leaf,fumitory, and terebinth extracts

In this study, nanofiber structures were obtained with convenient polymers (PVA [polyvinyl alcohol] and PCL [poly ^o-caprolactone]) derived from the herbal extracts of olive leaves, fumitory, and terebinth plants. Optimum nanofiber structures were identified by measuring viscosity and conductivity values and performing morphological analysis, characterization, and mechanical tests of the prepared solutions. The potential use for wound healing at the most efficient level was determined as a result of antibacterial analysis of the structures obtained. APT (PVA/terebinth) and BFO (PCL/fumitory) nanofibers had the thinnest diameter range and the highest strength values. In terms of the determination of antibacterial effects, nanofiber structures of all 3 plant species proved to be effective against bacteria. The greatest effect was observed against Escherichia coli in the nanofiber structure containing olive leaves, with a zone diameter of 32 mm. In addition, APT and BFO nanofibers had the highest values of thinness and strength. In these 2 samples, using BFO against Staphylococcus aureus and APT against Candida albicans increased their areas of activity. In the literature review, no study was available about obtaining nanofibers, especially from fumitory and terebinth plants. This study aimed to increase knowledge on obtaining nanofiber structures, including various polymers derived from olive leaves, fumitory, and terebinth plants.     

PVA/DTC纳米纤维的制备及对铅离子的吸附行为

通过高压静电纺丝技术制备了聚乙烯醇/聚乙烯亚胺(PVA/PEI)纳米纤维膜, 对纤维膜进行功能化使其转化为对重金属离子具有高络合能力的聚乙烯醇/二硫代氨基甲酸盐功能化聚乙烯亚胺(PVA/DTC)纳米纤维膜. 研究了PVA/PEI纳米纤维膜的交联和功能化以及PVA/DTC纤维膜对铅离子的吸附行为. 结果表明, 高压静电纺丝法可制备出纤维直径分布均匀、 形貌良好的纳米纤维膜, 且交联、 功能化后仍能保持蓬松纳米纤维状的网状结构. PVA/DTC纳米纤维膜对铅离子吸附速率快, 吸附量容量高, 且具有良好的再生吸附能力, 是一种潜在的重金属离子高效吸附材料.     

魔芋葡甘聚糖/聚乙烯醇纳米纤维膜及其释药行为研究

为了研制药物缓释效果优良的薄膜材料,利用静电纺丝设备研制不同比重的魔芋葡甘露聚糖/聚乙烯醇纳米纤维膜,并通过扫描电镜、傅里叶变换红外光谱和示差扫描量热法表征纳米纤维膜的结构和性能,结合体外实验和数学模型研究其缓释行为.结果显示当魔芋葡甘露聚糖含量占纳米纤维膜总质量约76%时,纳米纤维膜中微纤丝粗细最均匀且结点较少,纳米纤维膜中魔芋葡甘聚糖和聚乙烯醇之间存在明显的相互作用,含有5-氨基水杨酸的纳米纤维膜在pH=7.4 PBS磷酸盐缓冲液中25 h的累积释放量大约为45%,显示出良好的药物缓释效果,其缓释行为与Higuchi模型具有较高的拟合度.研究表明利用静电纺丝设备研制的魔芋葡甘聚糖/聚乙烯醇纳米纤维膜可以为药物缓释载体的开发提供理论依据.     

Preparation of Polymer Nanofibers Containing Silver Nanoparticles by Using Poly(N‐vinylpyrrolidone)

Summary: Poly(N‐vinylpyrrolidone) (PVP) was used in two methods to prepare polymer nanofibers containing Ag nanoparticles. The first method involved electrospinning the PVP nanofibers containing Ag nanoparticles directly from the PVP solutions containing the Ag nanoparticles. N,N‐Dimethylformamide was used as a solvent for the PVP as well as a reducing agent for the Ag⁺ ions in the PVP solutions. In the second method, poly(vinyl alcohol) (PVA) aqueous solutions were electrospun with 5 wt.‐% of the PVP containing Ag nanoparticles. The Ag nanoparticles were evenly distributed in the PVA nanofibers. PVP containing Ag nanoparticles could be used to introduce Ag nanoparticles to other polymer nanofibers that are miscible with PVP.

TEM image of a PVA nanofiber electrospun with 5 wt.‐% of the PVP containing Ag nanoparticles.     

PVA/GA/β-CD纳米纤维的制备及染料吸附性能

利用静电纺丝技术,以六氟异丙醇(HFIP)和水为溶剂,制备了环糊精(β-CD)含量为70%(质量分数)的聚乙烯醇(PVA)/β-CD纳米纤维,并经戊二醛(GA)交联处理得到了可用于染料吸附的PVA/GA/β-CD纳米纤维.通过红外光谱和扫描电子显微镜研究了交联反应前后纳米纤维组成和形貌的变化;考察了PVA/GA/β-CD纳米纤维对7种水溶性染料的吸附性能.结果表明,PVA/GA/β-CD纳米纤维对孔雀石绿、甲基紫和刚果红的吸附效果较好,最大吸附量分别为124.71,121.14和127.39 mg/g,4次吸附-解吸附循环后,染料去除率仍保持80%左右,在染料废水处理中具有良好的应用前景.