超声波处理对球形β-Ni(OH)2结构及电化学性能的影响

A method of ultrasonic treatment （UST） was first used to modify the structure and electrochemical performance of nickel hydroxide for the active material of nickel series alkaline batteries. The experimental results showed that UST was an effective method to improve the electrochemical performance of β-Ni（OH）2 such as specific discharge capacity, discharge potential, electrochemical reversibility and oxygen evolution over-potential. The results of electrochemical impedance spectroscopy, powder X-ray diffraction and particle size distribution indicated that the improvement of the performance of β-Ni（OH）2 through UST was attributed to the reduction of the charge-transfer resistance （Rt） and the diffusion impedance （Zw）, which resulted from the decrease of the crystallite and particle size and the increase of interlayer spacing. Diffusion coefficient of proton DH of ultrasonic treated β-Ni（OH）2 gained by CV tests was 1.13 × 10^-11 cm^2/s, and the average discharge specific capacity of ultrasonic treated β-Ni（OH）2 electrode was 301 mAh/g.     

Electrochemical Sensor Based on AgNPs-NNH Nanocomposites for Hydrogen Peroxide Detection by Zero Current Potentiometry

The layered nickel nitrate hydroxide (NNH)nickel base material was prepared by using hydrothermal method,and the AgNPs were synthe- sized on the surface of NNH.The layered AgNPs-NNH nanocomposites were dsed to construct electrochemical sensor for hydrogen peroxide detection. The morphology,composition and structure of the sensing interface materials were characterized and the relationship between zero current potential signals towards hydrogen peroxide and the response performance was explored.The results of field emission electron microscope (FESEM)and transmission electron microscope (TEM)showed that the NNH was layered material with a uniform thickness of 60nm,and AgNPs evenly dispersed on the surface of NNH layer,with the size of 15nm and 23rim,respectively.Based on zero current potentiometry,the electrochemical results indicated that the linear range was from 1.0nmol/L to 1.0mmol/L,with a detection limit of 0.3nmol/L and a sensitivity of 33.7μV-mM^-1.cm^-2.Compared to the chronoam- perometry,the detection limit was reduced four orders of magnitude.     

固相反应法合成掺铝的α型氢氧化镍及其电化学性能

Ni(OH)₂ including 20% Al was synthesized by solid-state reaction. The result of XRD indicated that the sample thus prepared was α-Ni(OH)₂， and its size and crystalline form were much poorer than those of the sample prepared by solution-state reaction. TG and DTA curves showed that α-Ni(OH)₂ began to decompose at higher temperature than β-Ni(OH)₂. The electrochemical behaviors of the sample were studied by cyclic voltammetry and constant current charge-discharge experiment. It was found that the sample by solid-state reaction had more ex-cellent electrode reversibility， higher discharge potential and higher discharge capacity.     

Ni–Al composite hydroxides fabricated by cation–anion double hydrolysis method for high-performance supercapacitor

Chemical doping of nickel hydroxide with other cations(e.g. Al~(3+)) is an efficient way to enhance its electrochemical capacitive performances. Herein, a simple cation–anion(Ni~(2+)and AlO_2) double hydrolysis method was developed toward the synthesis of nickel–aluminum(Ni–Al) composite hydroxides. The obtained composite hydroxides possesses a porous structure, large surface area(121 m~2/g) and homogeneous element distribution. The electrochemical test shows that the obtained composite hydroxides exhibits a superior supercapacitive performances(specific capacitance of 1670F/g and rate capability of 87% from 0.5 A/g to 20 A/g) to doping-free nickel hydroxide(specific capacitance of 1227 F/g and rate capability of 47% from 0.5 A/g to 20 A/g). Moreover, the galvanostatic charge/discharge test displays that after 2000 cycles at large current density of 10 A/g, the composite hydroxides achieves a high capacitance retention of 98%, indicative of an excellent electrochemical cycleability.     

The Deactivation of Nickel Hydroxide to Hypophosphite Electrooxidation on a Nickel Electrode

The deactivation of nickel hydroxide to the electrooxidation of hypophosphite on a nickel electrode was studied by means of in situ UV-Vis subtractive reflectance spectroscopy. The experimental results show that when the potential is lower than -1.0 V (SCE), the surface on nickel electrode is free of nickel hydroxide, on which hypophosphite is active. When the potential moves positively to about 0.75V, two absorbency bands around 300nm and 550nm, which were ascribed to the formation of α-nickel hydroxide, were observed, nickel is oxidized to α-nickel hydroxide. Severe deactivation of the surface occurs when the nickel surface is covered with nickel hydroxide, which separates the hypophosphite ion from nickel substrate.     

沉淀转化法制备的Co(OH)2的超级电容特性

Cobalt hydroxide, often used as an additive in nickel electrode, is rarely studied as active material for su-percapacitors. In this paper, the Co(OH)₂ with the particle size less than 20nm by deposition transformation was synthesized. Its single electrode specific capacitance was measured to be 92F·g^-1, and the electrode resistance was so low that the initial potential drop when discharging is unobvious even the discharge current increased to 200mA for a 1cm² electrode. After ten thousand cycles, Co(OH)₂ on the electrode changes to Co₃O₄ gradually, the resistance of the electrode does not increase much, while the specific capacitance increases to 133F·g^-1 at 10mA。     

Liquid phase synthesis of dendritic nickel carbide alloy with high conductivity for advanced energy storage

Alloy materials have attracted increasing attentions because they possess superior electrical conductivity which can contribute to excellent electrochemical performance. Herein a dendritic Ni_3C alloy material has been prepared by the pyrolysis of nickel acetylacetonate employing oleylamine as a reductant and 1-octadecene or octadecane as the solvent. The current–voltage curves indicating that the electrical conductivity of Ni_3C is higher than that of nickel oxide. Electrochemical testing indicates that a high specific capacity of 390 C/g is found in alkaline electrolyte at 0.5 A/g, and deliver excellent rate characteristic as well as cycle life. The excellent electrochemical performance may be attributed to its high electrical conductivity and dendritic nanostructure that can promote diffusion of electrolyte ions. In addition, the AC//Ni_3C asymmetric supercapacitor has been assembled at a cell voltages between 0 and 1.6 V, achieving a maximum energy density of 37 Wh/kg(at a power density of 0.3995 k W/kg), and this manifests that the Ni_3C alloy is a promising electrode material for electrochemical energy storage.     

Gold nanoparticles-enhanced bisphenol A electrochemical biosensor based on tyrosinase immobilized onto self-assembled monolayers-modified gold electrode

A novel electrochemical sensor based on the immobilization of tyrosinase(tyr) onto gold nanoparticles(nano-Au) and thioctic acid amide(T-NH2) self-assembled monolayers(SAMs)-modified gold electrode has been developed for the determination of bisphenol A(BPA).It was found that the nano-Au could significantly enhance the electrochemical response of tyr/nano-Au/T-NH2/Au electrode to BPA,and the enhancement effect of nano-Au on the current response was also related to the enzyme.The results indicated that the biosensor could be used as a detector for BPA determination with a linear range from3.99 ×10-7mol/L to 2.34 ×10-4mol/L and a detection limit of 1.33×10-7mol/L.In addition,this biosensor showed good reproducibility.     

A facile preparation and electrochemical properties of nickel based compound-graphene sheet composites for supercapacitors

Composites of a nickel based compound incorporated with graphene sheets(NiBC-GS) are prepared by a simple flocculation,using hydrazine hydrate as flocculant and reductant,from a homogeneous intermixture of nickel dichloride and graphene oxide dispersed in N,N-dimethylformamide.Morphology,microstructure and thermal stability of the obtained products were characterized by field-emission scanning electron microscopy,X-ray diffraction and thermal gravimetric analysis.Furthermore,the electrochemical properties of NiBC-GS,as electrode materials for supercapacitors,were studied by cyclic voUammetry and galvanostatic charge/discharge in 2 mol L~(-1) KOH solution.It was determined that for NiBC-GS annealed at 250 ℃.a high specific capacitance of 2394 Fg~(-1) was achieved at a current density of 1 Ag~(-1),with 78%of the value(i.e.,1864 Fg~(-1)) retained after 5000 times of repeated galvanostatic charge/discharge cycling.The high specific capacitance and available charge/discharge stability indicate the synthesized NiBC-GS250 composite is a good candidate as a novel electrode material for supercapacitors.     

A novel Fe（OH）3/TiO2 nanoparticles and its high photocatalytic activity

A very simple and controllable approach was proposed to synthesize novel Fe(OH)_3/TiO_2 nanoparticles.Compared with neat TiO2,the Fe(OH)_3/TiO_2 increased the rate of the photocatalytic degradation of methyl orange at pH 6.0 by more than five times, showing photocatalytic activity as excellent as P25.This enhancing effect is mainly attributed to the ferric hydroxide deposits as the electron scavenger and the enriched surface hydroxyl groups.     

Preparation of a novel composite electrode based on N-doped TiO_2-coated Na Y zeolite membrane and its photoelectrocatalytic performance

For the first time the preparation of the N-doped TiO_2-coated NaY zeolite membrane(N-doped TiO_2/NaY zeolite membrane) as an electrode material for photoelectrocatalysis has been achieved and reported.The XRD, SEM, UV–vis and XPS techniques were used to characterize the structure of the N-doped TiO_2/NaY zeolite membrane. The results verified that the surface of the N-doped TiO_2/NaY zeolite membrane was coated by TiO_2 nanoparticles of ca. 20 nm size and exhibited a distinct red-shift in the UV–vis spectra compared to N-doped TiO_2. The photoelectrocatalysis performance of the N-doped TiO_2/NaY zeolite membrane electrode was evaluated by phenol degradation. The results revealed it is a promising novel electrode material for application of photoelectrocatalysis in the removal of organic contaminants in waste water.     

Kinetic Study of the Electro-Catalytic Oxidation of Hydrazine on Cobalt Hydroxide Modified Glassy Carbon Electrode

Electrocatalytic oxidation of hydrazine was investigated on a cobalt hydroxide modified glassy carbon (CHM-GC) electrode in alkaline solution. The process of oxidation involved and its kinetics were established by using cyclic voltammetry, chronoamperometry techniques as well as steady state polarization measurements. In cyclic voltammetry (CV) studies, in the presence of hydrazine the peak current increase of the oxidation of cobalt hydroxide is followed by a decrease in the corresponding cathodic current. This indicates that hydrazine is oxidized on the redox mediator that is immobilized on the electrode surface via an electrocatalytic mechanism. A mechanism based on the electrochemical generation of Co(IV) active sites and their subsequent consumption by the hydrazine in question was also investigated.     

Electrochemical performance of Klason lignin as a low-cost cathode-active material for primary lithium battery

A few classes of organic compounds are promising electrode-active materials due to their high power and energy densities,low cost,environmental friendliness,and functionality.In the present work,the possibility of using Klason lignin extracted from buckwheat husks as a cathode-active material for a primary lithium battery has been investigated for the first time.The reaction mechanism in the lithium/lignin electrochemical cell was suggested based on the deep galvanostatic discharge(up to 0.005 V) data and cyclic voltammetry results.The dependence of the electrochemical behavior of the Klason lignin on the milling degree was evaluated.The maximum specific capacity of the lignin is equal to 600 m Ah g-1at a discharge current density of 75 μA cm-2.Beneficial effect of the thermal treatment of the Klason lignin cathode at250°C on the cell performance was established.It was found that the discharge capacity of the cell increased by 30% in the range from 3.3 to0.9 V for the treated cathode material.These results demonstrate the prospects of using Klason lignin-based electrochemical cells as low-rate primary power sources.     

Nickel and potassium co-modified β-Mo2C catalyst for CO conversion

Nickel and potassium co-medified β-Mo2C catalysts were prepared and used for CO hydrogenation reaction. The major products over β-Mo2C were C1-C4 hydrocarbons, only few alcohols were obtained. Addition of potassium resulted in remarkable selectivity shift from hydrocarbons to alcohols at the expense of CO conversion over β-Mo2C. Moreover, it was found that potassium enhanced the ability of chain propagation with a higher C2+OH production. Modified by nickel, β-Mo-2C showed a relatively high CO conversion, however, the products were similar to those of pure β-Mo2C. When co-modified by nickel and potassium,β-Mo2C exhibited high activity and selectivity towards mixed alcohols synthesis, and also the whole chain propagation to produce alcohols especially for the stage of C1OH to C2OH was remarkably enhanced. It was concluded that the Ni and K had, to some extent, synergistic effect on CO conversion.     

Electrochemical water oxidation by photo-deposited cobalt-based catalyst on a nano-structured TiO2 electrode

A cobalt-based catalyst was directly photo-deposited on the surface of a widely used n-type nano-structured semiconductor(TiO 2).Different thicknesses of the TiO 2 films as well as different time of photo-deposition of the Co-based catalyst on TiO 2 films have been optimized.It was found that the electrode with 3 layers of TiO 2 film(in 8 m thickness) and 1 hour photo-deposition of the cobalt-based catalyst by light irradiation from a 500 W Xenon lamp gave the highest current density(～5 mA/cm 2).Using this cobalt-modified TiO 2 film as a working electrode in an electrochemical device,highly efficient water oxidation has been demonstrated in a pH 7.0 aqueous solution with low overpotential.     

新型钛基镍电极对肼氧化反应的电催化活性

A novel titanium-supported nickel electrode(Ni/Ti) was fabricated by a hydrothermal process using NiSO4 and hydrazine as raw materials. The structure of Ni/Ti was characterized by SEM and EDS. Oxidation of hydrazine on the Ni/Ti electrode in 1 mol·L-1 NaOH solution was studied with cyclic voltammograms(CV) and chronoamperometry (CA).The results show that Ni/Ti electrode was electrochemically active towards hydrazine oxidation. The high current density was recorded on the Ni/Ti electrode,and the onset potential for the hydrazine oxidation was-0.3 V as the hydrazine concentration was 70 mmol·L-1. This novel nickel electrode would be a promising anodic material used in direct hydrazine fuel cells.     

The protection effect of β-CD on DNA damage induced by ultrafine TiO_2

Under the photocatalysis of 365 nm ultraviolet radiation,ultrafine TiO2 caused the oxidative damage of Teasy plasmid DNA. The damage was determined by gel-electrophoresis. Then,a different dose of β-CD was added to the reaction,and the damage was restrained. The rate of damage restraining reached 97% when the mass of β-CD was 4 times as that of TiO2. Through UV scan and IR spectroscopy,it was found that the Ti-O of ultrafine TiO2 was bound with -OH of β-CD cavum and the -OH on the surface of ultrafine TiO2 disappeared,so the formation of ?OH was controlled. The ultrafine TiO2 has been widely used,but it was determined to be carcinogenic by some research. The protection effect of β-CD to DNA in the molecular level takes a new look on the surface modification of nano particles to decrease the toxic effect.     

The protection effect of β-CD on DNA damage induced by ultrafine TiO2

Under the photocatalysis of 365 nm ultraviolet radiation, ultrafine TiO2 caused the oxidative damage of Teasy plasmid DNA. The damage was determined by gel-electrophoresis. Then, a different dose of β-CD was added to the reaction, and the damage was restrained. The rate of damage restraining reached 97% when the mass of β-CD was 4 times as that of TiO2. Through UV scan and IR spectroscopy, it was found that the Ti-O of ultrafine TiO2 was bound with -OH of β-CD cavum and the -OH on the surface of ultrafine TiO2 disappeared, so the formation of · OH was controlled. The ultrafine TiO2 has been widely used, but it was determined to be carcinogenic by some research. The protection effect of β-CD to DNA in the molecular level takes a new look on the surface modification of nano particles to decrease the toxic effect.     

Hollow polyhedron structure of amorphous Ni-Co-S/Co(OH)_2 for high performance supercapacitors

In power storage technology,ion exchange is widely used to modify the electronic structures of electrode materials to stimulate their electrochemical properties.Here,we proposed a multistep ion exchange(cation exchange and anion exchange) strategy to synthesize amorphous Ni-Co-S and β-Co(OH)_2 hybrid nanomaterials with a hollow polyhedron structures.The synergistic effects of different components and the remarkable superiorities of hollow structure endow Ni-Co-S/Co(OH)_2 electrode with outstanding electrochemical performance,including ultra-high specific capacity(1440.0 C/g at 1 A/g),superior capacitance retention rate(79.1% retention at 20 A/g) and long operating lifespan(81.4% retention after5000 cycles).Moreover,the corresponding hybrid supercapacitor enjoys a high energy density of 58.4 Wh/kg at the power density of 0.8 kW/kg,and a decent cyclability that the capacitances are maintained at80.8% compared with the initial capacitance.This research presents a high-performance electrode material and provides a promising route for the construction of electrode materials for supercapacitors with both structural and component advantages.     

Electrochemical Co-reduction of Bi(Ⅲ)and Y(Ⅲ)and Extracting Yttrium from Molten LiCl-KCl Using Liquid Bi as Cathode

The electrochemical reaction of Bi(Ⅲ)and co-reduction behaviour of Bi(Ⅲ)and Y(Ⅲ)ions were researched in molten LiCl-KCl on a ttmgsten(W)electrode employing a range of electrochemical teclmiques.Cyclic voltammetric and square-wave voltanunetric results revealed that the reduction of Bi(Ⅲ)was a one-step process,with the exchange of three electrons on a W electrode,and diffusion-controlled.The electrochemical curves showed two reduction peaks pertaining to the formation of Bi-Y alloy compounds,because of the co-reduction of Bi(Ⅲ)and Y(Ⅲ) by metallic Y deposited on the pre-deposited Bi-coated W electrode and reacting with Bi metal in molten LiCl-KCl. Furthermore,galvanostatic electrolysis was conducted using liquid Bi as cathode to extract yttrium at different current intensities,and the extractive products were analyzed by SEM,EDS and XRD.The results indicated that BiY intermetallic compotmd was formed in the molten LiCl-KCl-YCl3 system.