Chromatic dispersion behavior of Si-NC-Er doped optical fiber

The chromatic dispersion for conventional and Er-doped fibers using the refractive index approximation is examined. A first, analytical method for investigation of dispersion in step index triple clad optical fiber is used. To design of zero-dispersion shifted fiber for optical communication purpose manipulation of the refractive index and radius of the core are considered. We show that in presence of the Si-NC-Er ions, zero-dispersion wavelength is displaced and the dispersion quantity is increased. In this work, we try to optimize system parameters to obtain minimum dispersion and dispersion shifted fiber with control of the doping levels of Er ions and Si-NC as well as doping profiles. For especial case, we assumed the Gaussian inhomogeneous core refractive index for zero-dispersion wavelength and dispersion managements.     

用阶跃有效折射率模型研究光子晶体光纤色散特性

在采用阶跃有效折射率模型研究光子晶体光纤的可行性方面，提出了将普通单模光纤、色散位移光纤、色散平坦光纤作为一定极限条件下的折射率引导型光子晶体光纤特例的观点.通过编程计算，并与文献报道的实验数据对比，表明应用本模型可以揭示光子晶体光纤所具有的奇异的色散机理.特别是应用本模型具有更快的计算速度.还用本模型分析了空气孔直径、周期及芯径对色散特性的影响. 关键词： 折射率引导型光子晶体光纤 阶跃有效折射率模型 色散     

Research on WDM optical fiber transmission system based on fiber Raman amplifier

After wavelength division multiplexing (WDM) optical fiber transmission system based on fiber Raman amplifier (FRA) is investigated in detail, the influence of the collocation of dispersion compensation fiber (DCF), the dispersion coefficient, dispersion slope (DS), effective core area, nonlinear index, length of FRA, launch power and the bandwidth of Bessel filter on bit error rate (BER) is deduced. The influence of Rayleigh backscattering noise on optical signal noise ratio (OSNR) is also investigated, which affects the performance of long haul transmission badly. The result indicates that the broadband long haul transmission can be realized through the reasonable design of the fiber. The result is useful to the optimal design of the WDM optical fiber transmission system based on FRA.     

Broadband dispersion compensating fiber using index-guiding photonic crystal fiber with defected core

We present a novel broadband dispersion compensating photonic crystal fiber with defected core in this paper. The small central defect of air hole can flexibly control the chromatic dispersion properties of this kind of photonic crystal fiber. This kind of fiber has broadband large negative chromatic dispersion, and the chromatic dispersion coefficient varies from -440 to -480 ps/（nm.km） in the measured wavelength range of 1500 - 1625 nm. The calculated chromatic dispersion curve is well matched to the measured chromatic dispersion coefficient in the range of 1500 - 1625 nm. The proposed photonic crystal fiber can be used to design the dispersion compensating fiber in the desired wavelength range by adjusting its structural parameters.     

基于光纤光栅波长路由的光纤自愈网

介绍了一种基于光纤光栅波长路由的全光双纤单向自愈环网,环内四节点具有16×10Gbit/s的传输能力。利用啁啾光纤光栅(CFBG)的波长可选择特性,实现了分布式的上下话路和波长选择功能,同时有效地补偿了传输色散。网络管理参照了网络管理协议(SNMP)的网络管理模型,通过对网络的重要参数进行实时监测来控制网络运行。实验结果表明,当环上任一处光缆发生故障时,通信业务能够自动恢复,恢复时间小于50ms,可实现网络的快速自愈,符合ITU-T G.841的建议规定。     

Broadband fiber Bragg gratings for dispersion management

This paper provides an overview and technology update of a dispersion management component made from chirped fiber Bragg gratings. The history and technology of fiber Bragg gratings (FBGs) have been extensively covered in several excellent review articles, [1-6] book chapters, [7] and books. [8,9] We give a brief overview of fiber Bragg grating technology in this section and then focus on the details concerned with construction and performance of dispersion management devices in optical communications systems with a single broadband long-length grating used in reflection. Sampled chirped grating are sometimes referred to as broadband devices, but they actually have a narrow bandwidth of operation that is periodically repeated across a given spectral range. Although these periodic devices have shown promise as dispersion management devices in communications systems, they will not be discussed in this paper.     

色散补偿和色散位移光纤实现光脉冲压缩

根据超短光脉冲在光纤中传输的非线性薛定谔方程，模拟了不同色散参量情况下色散补偿和色散位移光纤对增益开关半导体激光器产生的光脉冲的压缩，给出了光脉冲在经过色散补偿光纤前后的啁啾曲线。结果表明，使用色散参量D分别为-150，-180和-20ps/(nm·km)的色散补偿光纤可以实现其他脉冲压缩方法的压缩效果，最大压缩因子达到6.09，但色散参量越大，所需光纤长度就越短。此外，脉冲经过色散补偿光纤后线性啁啾几乎为零。还利用色散位移光纤对脉冲进行孤子压缩，脉冲宽度由最初的45ps减小到1.23ps。指出采用这2种光纤相结合的方法可以对光脉冲实现高效压缩。     

微结构聚合物光纤中高双折射可调效应研究

通过在纤芯附近引入两个直径较大的空气孔诱导纤芯局部双折射,在包层减小x方向的孔间隔诱导包层双折射,设计实现了一种高双折射随波长可调效应的微结构光纤.采用全矢量平面波方法,以聚合物甲基丙烯酸甲酯为基材,对其偏振特性和基模模场进行了研究.结果发现,该光纤基模双折射在光通信波段呈现两个最大值,且最大双折射大小和位置随光纤结构和波长的变化可以进行调节.通过调节光纤结构参数,模拟得到了该光纤具有高双折射和零偏振模色散的最佳设计参数. 关键词： 导波与光纤光学 双折射可调 聚合物 全矢量平面波法     

Optical fibers and fiber dispersion compensators for high-speed optical communication

In order to meet the requirements necessary for advanced optical fiber transmission schemes that enable larger transmission capacity, higher efficiency and/or lower transmission costs per bit, optical fiber technologies are still evolving toward ultimate performance. Recent developmental activities have realized a number of improved performance optical fibers, such as ultra-low loss or ultra-low nonlinearity fibers and various types of dispersion-modified fibers. Fiber-based dispersion compensators or dispersion compensating fibers have also become one of the most essential optical components that support high-speed large capacity optical transmission. Very recently, the dispersion compensating fibers have further evolved into dispersion-managed optical transmission lines, which are now being actually deployed in transoceanic submarine optical cable networks.     

PBG光子晶体光纤的色散特性研究

光子晶体光纤(PCF)是一种具有特殊包层结构的光纤,它是利用光子禁带效应(PBG)来导光的。利用时域有限差分法(FDTD)来分析光波在PCF中传输的色散特性,结果表明,PBG光子晶体光纤的色散值和色散斜率比常规的通信光纤要小。     

Power-independent technique to extract the dispersion parameters of an optical fiber using four wave mixing

Conventional methods which extract dispersion parameters of an optical fiber using four wave mixing rely on the measurement of optical power in the generated wavelengths, and hence are prone to measurement errors. We propose and demonstrate a power-independent method to extract the dispersion curve of a fiber using four wave mixing (FWM). The analytical equations that have been traditionally used to estimate the phase mismatch in FWM are modified to cater to low-dispersion fibers, and are verified. Experiments to obtain the dispersion curve of a low-dispersion and highly nonlinear fiber are discussed and the results are analyzed. Limitations of any FWM-based method to extract the dispersion curve of a fiber are presented for the first time.     

Dispersion-flattened polarization-maintaining photonic crystal fiber for nonlinear applications

In this paper, we propose a novel photonic crystal fiber design to achieve high birefringence, high nonlinearity with a flattened dispersion profile. The air holes which are embedded in silica are arranged in triangular lattice configuration. In the core region, an air hole is introduced as the central defect to flatten the dispersion curve. The shape of the defect air hole is deliberately designed elliptical so that high birefringence in the PCF is obtained for polarization-maintaining purpose. The structural parameters are carefully selected to optimize the optical properties.     

Design of zero dispersive double clad fiber for high efficiency operation of two color light

A double clad solid silica fiber is newly designed for applications which need the high efficiency operation of two colors of light. Ultrashort pulses with a central wavelength of 800?nm are delivered by the core of the double clad fiber which can realize the transmission of the optical pulses with a net chromatic dispersion of zero. This is achieved by integrating the double clad fiber with a pair of long period gratings, which allows optical pulses to propagate in a higher order mode (LP₀₂) in the middle of the fiber as well as in a fundamental mode (LP₀₁) at the beginning and end of the fiber. The index profile of the double clad fiber is engineered so that the higher order mode has high anomalous dispersion that can be used to compensate for normal dispersion of the fundamental mode. By controlling the lengths of the fiber where pulses are in a fundamental and in a higher order modes, the fiber with total zero dispersion can be realized. The double clad fiber can collect 100?% of visible light within the numerical aperture of 0.21 with a loss of the optical pulses less than 1?%. The design of this fiber is essential for applications including fiber-optic nonlinear imaging for compactness, robustness, and low optical power loss in dispersion compensation.     

Chromatic and opto-mechanical dispersion of some characteristic parameters of optical fiber undergoing macrobending

Bending of optical fiber leads to an induced-anisotropy in the index profile that influences many important guiding fiber parameters. An analytical method is described for the measurement of refractive-index-wavelength dispersion in bent optical fibers. Multiple-beam Fizeau fringes technique at transmission is used to analyze the opto-mechanical properties and induced-index anisotropy in a standard single-mode fiber undergoes pure mechanical macrobending. The shift in Fizeau fringes is employed to evaluate the dispersion of the cladding material of the bent fiber. The radial variations in Cauchy’s coefficients and the associated variations of some fiber parameters due to macrobending are carried out. The radial profiles of some material parameters such as oscillation energy, dispersion energy, lattice energy and material dispersion are measured as well. The presented method is capable to achieve quantitative and qualitative measurements, which is not available with other methods. The method has a good index resolution in the order of 10⁻⁴ and spatial resolution of 1.3 μm.     

双包层稀土掺杂光纤抽运吸收特性的分析

建立了复折射率纤芯结合有限差分束传播法的双包 层稀土掺杂光纤抽运吸收效率数值模型,利用该模型对几种常 用内包层外边界结构下双包层稀土掺杂光纤的抽运吸收系数进 行了详细的分析,得出相应双包层光纤的抽运吸收特性. 分析结果对双包层稀土掺杂光纤的优化设计具有重要的指导意义.     

Cross-phase modulation in long-haul systems with chirped fiber Bragg gratings-based dispersion compensators

The cross-phase modulation (XPM) effect in fiber links with dispersion compensated by chirped fiber Bragg gratings (CFBGs) is analyzed here for the first time. A continuous-wave (CW) signal, referred to as a probe, is used to investigate the impact of XPM on communication systems. The result shows that the XPM in systems using CFBGs as dispersion compensators is greatly suppressed, compared with that of systems using dispersion compensated fiber (DCF). The difference of the dispersion management between the system using DCF and that using CFBGs is demonstrated, too.     

Bismuth-based erbium-doped fiber as a gain medium for L-band amplification and Brillouin fiber laser

Bismuth-based erbium-doped fiber (Bi-EDF) is demonstrated as an alternative medium for optical amplification and nonlinear applications. The bismuth glass host provides the opportunity to be doped heavily with erbium ions to allow a compact optical amplifier design. The bismuth-based erbium-doped fiber amplifier (Bi-EDFA) is demonstrated to operate at wavelength region from 1570 to 1620 nm using only a 215 cm long of gain medium. The maximum gain of 15.8 dB is obtained at signal wavelength of 1610 nm with the corresponding noise figure of about 6.3 dB. A multi-wavelength laser comb is also demonstrated using a stimulated Brillouin scattering in the 215 cm long Bi-EDF assisted by the 1480 nm pumping. The laser generates more than 40 lines of optical comb with a line spacing of approximately 0.08 at 1612.5 nm region using 152 mW of 1480 nm pump power.     

Dispersion characteristic of hexagonal and square lattice chalcogenide As2Se3 glass photonic crystal fiber

In this paper, we report a chalcogenide As₂Se₃ glass photonic crystal fiber (PCF) for dispersion compensating application. We have used the improved fully vectorial effective index method (IFVEIM) for comparing the dispersion properties (negative and zero dispersion) and effective area in hexagonal and square lattice of As₂Se₃ glass PCF using different wavelength windows. It has been demonstrated that due to their negative dispersion parameter and negative dispersion slope in wavelength range 1.2-2.5 μm, both lattice structures of As₂Se₃ glass PCFs, with pitch (Λ = 2 μm), can be used as dispersion compensating fibers. Further, design parameters have been obtained to achieve zero dispersion in these fibers. It is also shown that As₂Se₃ glass PCF provides much higher negative dispersion compared to silica PCF of the same structure, in wavelength range 1.25-1.6 μm and hence such PCF have high potential to be used as a dispersion compensating fiber in optical communication systems.     

Theoretical realization of holey fiber with flat chromatic dispersion and large mode area: an intriguing defected approach

We present a novel design approach for realizing holey fibers (HFs) with flat dispersion characteristics and large mode area based on the existence of an artificially defected air-hole ring in the cladding, and on the inclusion of additional defected air holes in the core of the fiber. This unique type of HF can be used for achieving remarkable flat dispersion characteristics as well as a large mode area, which are particularly useful for high-speed data transmission. The validation of the proposed design is done by adopting an efficient full-vectorial finite element method for optical characterization of HFs. The proposed fiber can be employed in reconfigurable optical transmission systems for performing wavelength division multiplexing operation. Typical characteristics of the proposed HF are a flattened dispersion of 6.3 +/- 0.5 ps/km/nm from 1.45 to 1.65 microm and an effective mode area as large as 100 microm2 in the same frequency range.     

Generation of domain-wall solitons in an anomalous dispersion fiber ring laser

We report experimental observations performed using a net anomalous dispersion Er-doped fiber ring laser without polarization-selective elements, highlighting the domain-wall solitary pulses generated under the incoherent polarization coupling. By adjusting the pump power and the polarization state appropriately, bright and dark solitons can stably co-exist in the cavity, both centered at 1562.16 nm with a 3-dB spectral width of ～ 0.15 nm and a repetition rate of 3.83 MHz. Moreover, the 0.8 mm long thulium-doped fiber (TDF) facilitated the mode-locking and self-starting of the laser. This is the first demonstration of a laser being used to generate bright and dark solitons synchronously while using TDF as the saturable absorber (SA). Except possessing the all-fiber structure, the laser exhibits good stability, which may have a significant influence on improvement of the pulse-laser design, and may broaden practical applications in optical sensing, optical communication, and soliton multiplexed systems.