Tunable comb-filter using thermally expanded core fiber and ytterbium doped fiber and its application to multi-wavelength fiber laser

We constructed a novel tunable comb-filter by splicing a commercial Yb³⁺ doped fiber (YDF) between 2 thermally expanded core (TEC) fibers at their core-expanded ends. This structure forms an all-fiber Mach-Zehnder interferometer due to the interference between the core mode and the cladding modes of the YDF. The interference fringes shifts to the longer wavelength region as the YDF is pumped by a 980 nm laser diode (LD). We then demonstrated application of this newly proposed tunable comb-filter to a SOA-based ring laser and obtained multi-wavelength lasing. The lasing wavelengths can be also tuned by pumping the YDF in the proposed comb-filter.     

高斜率效率L波段宽带可调谐光纤环形腔激光器

利用环形腔结构在L波段获得了43nm(1567.1nm-1610.1nm）范围的宽带连续可调谐激光输出。由于同时采用了高浓度掺铒光纤和1480nm激光二极管（LD）抽运源，极大地降低了激光器的抽运阈值，提高了斜率效率和输出功率。在整个可调范围内，激光器的输出功率达10．9dBm-12.1dBm(95mW抽运），信噪比高于60dB，在1585nm的斜率效率为0．201。     

L-Band Multi-Wavelength Brillouin–Raman Fiber Laser with 20-GHz Channel Spacing

Abstract

A tunable multi-wavelength L-band Brillouin–Raman fiber laser with a 20-GHz channel spacing utilizing bidirectional ring cavity is proposed and experimentally investigated. The laser employs a co-pumped dispersion compensating fiber as a gain medium for both Brillouin and Raman gains. With a Raman pump of 425 mW, the laser system can generate up to 12 double-spaced Brillouin Stokes signals. This simple laser configuration provides stable Brillouin Stokes signals in the absence of self-lasing cavity modes with a tuning range exceeding 35 nm without using any filtering mechanism. The Stokes signals have more than 20 dB of optical signal-to-noise ratio.     

室温下稳定的多波长掺铒光纤激光器的研究

通过在线形谐振腔中引入一段缠绕在压电陶瓷上的单模光纤作为正弦相位调制器,使得激射波长的损耗不固定,抑制由于掺铒光纤的均匀展宽效应引起的模式竞争,从而避免了在室温下不稳定的单波长激射,实现了多波长掺铒光纤激光器的稳定输出。为了获得平坦的多波长输出,在谐振腔里使用了一个损耗峰位于1530nm处的长周期光纤光栅,以获得较为平坦的增益谱。通过两个3dB耦合器制成的反射型梳状滤波器的滤波作用,实验中观察到稳定的多波长激射,相邻波长间隔约为0．45nm。中心9个波长的输出功率平坦度为10dB,边模抑制比大于25dB。     

An Efficient Photonic Crystal Fiber-Based Brillouin Erbium Fiber Laser Using a Fiber Bragg Grating for Multi-Wavelength Generation

Abstract

An efficient multi-wavelength Brillouin erbium fiber laser is demonstrated using an improved configuration with a broadband fiber Bragg grating and a piece of photonic crystal fiber. The laser generates more than 55 lines of optical comb with a line spacing of approximately 0.09 nm in a 1,565-5 nm region using pump powers of 3 dBm and 150 mW for the Brillouin and 980-nm pumps, respectively. The Brillouin erbium fiber laser with a fiber Bragg grating's reflectivity of 50% obtained a higher number of comb lines compared to that of 99% reflectivity.     

输出平均功率大于2W的高功率、包层抽运、超短脉冲铒镱共掺光纤激光器

采用主振荡功率放大的方式，研制成功集宽带波长连续可调谐、带宽内输出功率谱均衡、高重复频率和高功率性能于一体的超短脉冲包层抽运铒镱共掺光纤激光器.将优化主振荡器和功率放大器的腔结构与掺铒光纤的饱和增益特性结合起来，实现了1535nm—1570nm(35nm带宽)的输出功率均衡的波长连续可调谐激光输出，在带宽内激光功率的最大波动仅为0.5dBm；带宽内平均输出功率大于2W、脉冲重复频率大于10GHz、脉冲宽度小于30ps.该激光器具有综合性能指标先进、结构简单、全光纤化、使用方便等优点. 关键词： 光纤激光器 包层抽运 短脉冲 高重复频率     

Random lasing in an organic light‐emitting crystal and its interplay with vertical cavity feedback

The simultaneous vertical‐cavity and random lasing emission properties of a blue‐emitting molecular crystal are investigated. The 1,1,4,4‐tetraphenyl‐1,3‐butadiene samples, grown by physical vapour transport, feature room‐temperature stimulated emission peaked at about 430 nm. Fabry‐Pérot and random resonances are primed by the interfaces of the crystal with external media and by defect scatterers, respectively. The analysis of the resulting lasing spectra evidences the existence of narrow peaks due to both the built‐in vertical Fabry‐Pérot cavity and random lasing in a novel, surface‐emitting configuration and threshold around 500 μJ cm⁻². The anti‐correlation between different modes is also highlighted, due to competition for gain. Molecular crystals with optical gain candidate as promising photonic media inherently supporting multiple lasing mechanisms.     

Tunable double-clad ytterbium-doped fiber laser based on a double-pass Mach-Zehnder interferometer

We have demonstrated an adjustable double-clad Yb³⁺-doped fiber laser using a double-pass Mach-Zehnder interferometer. The laser is adjustable over a range of 40 nm from 1064 nm to 1104 nm. By adjusting the state of the polarization controller, which is placed in the double-pass Mach-Zehnder interferometer, we obtained central lasing wavelengths that can be accurately tuned with controllable spacing between different tunable wavelengths. The laser has a side mode suppression ratio of 42 dB, the 3 dB spectral width is less than 0.2 nm, and the slope efficiencies at 1068 nm, 1082 nm and 1098 nm are 23%, 32% and 26%, respectively. In addition, we have experimentally observed tunable multi-wavelengths lasing output.     

Lasing modes in a spiral-shaped dielectric microcavity

The resonance patterns and lasing modes in a spiral-shaped dielectric microcavity are investigated through passive and active medium calculations. We find that the high-Q resonance modes are whispering-gallery-like modes, and these resonance modes can be easily excited as lasing modes. We also find that the quasi-scarred resonance mode, which shows strong directional emission beams from the cavity boundary, can be excited with selectively applied external pumping. Through a spectral analysis of the time evolution of the light field, the competition between these lasing modes is discussed.     

Switchable dual-wavelength Erbium-doped fiber ring laser with cascaded fiber Bragg gratings

We have experimentally shown wavelength mode switching in a dual-wavelength Erbium-doped single cavity fiber laser where the initial two wavelengths of 1 nm spacing are determined by the cascaded reflection type short-period fiber Bragg gratings having two different centre wavelengths of 1550.5 and 1551.5 nm. The lasing mode depends on the polarization in the ring cavity to migrate from one wavelength to another or operates in both modes in a polarization beam splitter output. To effectively control the polarization in the ring cavity, the polarization controllers were positioned before and after the polarization beam splitter. This method of wavelength switching provides a simple way of mode tuning in dual-wavelength fiber lasers.     

基于增强瑞利反馈的单模窄线宽随机激光器

仿真说明了单模光纤(SMF)中瑞利散射(RS)的机理, 指出纤芯掺杂的不均匀性以及拉丝过程引起的光纤几何尺寸的随机变化是光纤中RS产生的主要原因, 并以此为基础制作了损耗为0.54 dB/km的散射光纤. 在通信波段, 5 km该散射光纤的瑞利背向散射(RBS)强度高于相同长度的SMF-28近5 dB. 在基于RBS单模随机激光器的数值模拟中, 大量的具有随机幅度和相位的纵模在经历不平坦增益的多次放大之后, 只有在增益最大点附近的模式能够克服损耗成为输出模式. 实验中以掺铒光纤作为增益介质, 500 m散射光纤提供随机反馈, 窄带布拉格光纤光栅(FBG)作为波长选择器件, 得到线宽约3.5 kHz、对比度近50 dB的单模激光输出. 与采用相同长度SMF-28的随机激光器相比, 其阈值电流降低了80 mA, 相同抽运条件下的最大输出功率提高了3 dBm. 该单模窄线宽随机激光器的输出波长的调谐特性仅由FBG的中心波长决定.     

Optical receiver with large-area photodiode for multilevel modulation

A large-diameter PIN photodiode (400 μm) with antireflection coating optimized for wavelength 650 nm was integrated with an automatic gain control transimpedance amplifier, linear post amplifier and 50Ω linear driver. The presented optical receiver shows a high linearity in receiving multilevel signals. A sensitivity of ?29.5dBm (BER = 10^?9) at 200 Mb/s with binary signal was achieved. By using four-level pulse amplitude modulation (4-PAM) a data rate of 400 Mb/s and a sensitivity of ?21.5 dBm (SER = 10^?9) was achieved.     

Tunable microwave signal generation based on an Opto-DMD processor and a photonic crystal fiber

Frequency-tunable microwave signal generation is proposed and experimentally demonstrated with a dual-wavelength single-longitudinal-mode （SLM） erbium-doped fiber ring laser based on a digital Opto-DMD processor and four-wave mixing （FWM） in a high-nonlinear photonic crystal fiber （PCF）. The high-nonlinear PCF is employed for the generation of the FWM to obtain stable and uniform dual-wavelength oscillation. Two different short passive sub-ring cavities in the main ring cavity serve as mode filters to make SLM lasing. The two lasing wavelengths are electronically selected by loading different gratings on the Opto-DMD processor controlled with a computer. The wavelength spacing can be smartly adjusted from 0.165 nm to 1.08 nm within a tuning accuracy of 0.055 nm. Two microwave signals at 17.23 GHz and 27.47 GHz are achieved. The stability of the microwave signal is discussed. The system has the ability to generate a 137.36-GHz photonic millimeter signal at room temperature.     

Theoretical study on the lasing plasmon of a split ring for label-free detection of single molecules and single nanoparticles

This paper reports the plasmonic lasing of a split ring filled with gain material in water. The lasing mode(1500 nm)is far from the pump mode(980 nm), which can depress the detection noise from the pump light. The laser intensities of the two modes simultaneously increase by more than 10~3 in amplitude, which can intensify the absorption efficiency of the pumping light and enhance the plasmonic lasing. The plasmonic lasing is a sensitive sensor. When a single protein nanoparticle(n = 1.5, r = 1.25 nm) is trapped in the gap of the split ring, the lasing spectrum moves by 0.031 nm, which is much larger than the detection limit of 10~(-5) nm. Moreover, the lasing intensity is also very sensitive to the trapped nanoparticle. It reduces to less than 1/600 when a protein nanoparticle(n = 1.5, r = 1.25 nm) is trapped in the gap.     

Multiwavelength erbium-doped fiber laser based on nonlinear polarization rotation assisted by four-wave-mixing

We experimentally demonstrate a simple-structure but efficient multiwavelength erbium-doped fiber laser based on nonlinear polarization rotation assisted by four-wave-mixing (FWM). Based on the combination of these two nonlinear mechanisms contributing to intensity-dependent loss to alleviate mode competition, the stable multiwavelength operation at room temperature can be realized in a length of dispersion-shifted fiber. We achieved up to 38-wavelength generation with a spacing of ∼0.4 nm in the laser. In addition, through tuning the birefringence fiber filter, the lasing wavelength can be accurately tuned in the free spectrum range.     

17-channels S band multiwavelength Brillouin/Erbium Fiber Laser co-pump with Raman source

In this paper, we propose and demonstrate a stable Brillouin-Erbium Fibre Laser (BEFL) capable of generating up to 17 lasing wavelengths in the Short-Wave length (S-band) region. The proposed setup uses a 7.7 km Dispersion Compensating Fibre (DCF) to act as a non-linear gain medium and a 30 m long Depressed-Cladding Erbium Doped Fibre (DC-EDF) as an optical amplifier for amplification in the S-band region. The proposed BEFL has an optimum tuning range of 1499 to 1502 nm and is capable of generating 17 lasing wavelengths with peak powers of between −20 to −15 dBm when injected with a Brillouin Pump (BP) of 5 dBm at 1499 nm and a Raman Pump (RP) of 300 mW at 1420 nm.     

Performance of Distributed Fiber Raman Amplifier Based on Hybrid Cladding Photonic Crystal Fiber

Abstract

This article presents a feasibility study for using a hybrid cladding photonic crystal fiber as a distributed fiber Raman amplifier based transmission link with negligible confinement losses and flattened dispersion characteristics. The simulation results clearly indicate that a bit error rate of 10^?9 can be maintained at the end of a (4 × 170)-km distributed fiber Raman amplifier link operating with 40 Gbps and 0.6 dBm transmit power if 20 dBm of pump power is used for each span.     

Stable zirconia-erbium doped multiwavelength fiber laser by precise control of polarization states

A compact zirconium-erbium doped fiber (Zr-EDF) based multiwavelength fiber laser (MWFL) with stable output comb is proposed and demonstrated. The MWFL utilizes a 3 m long Zr-EDF with an erbium concentration of 3000 ppm and pumped by a 1480 nm laser diode (LD) as the active gain medium. A fiber based multimode polarization controller (PC) is used to precisely control the polarization states of the oscillating modes in the MWFL, distributing the total energy of the system among the lasing wavelengths in order to overcome the mode-suppression and mode-competition that arises from homogenous line broadening. The MWFL is capable of generating up to four lasing wavelengths with average peak powers of 0.08 dBm in the extended L-band of 1600 nm. The lasing wavelengths have a 3-dB linewidth of 0.1 and an extinction ratio of 40 dB as well as highly stable, with minimal fluctuations of less than 0.6 dB observed in the peak powers of the lasing wavelengths over a period of 1 h. The proposed system allows for the realization of a compact, cost-effective and stable erbium based MWFL capable of operating at room temperature.     

Photonic crystal nanocavity laser in an optically very thick slab

A photonic crystal (PhC) nanocavity formed in an optically very thick slab can support reasonably high-Q modes for lasing. Experimentally, we demonstrate room-temperature pulsed lasing operation from the PhC dipole mode emitting at 1324 nm, which is fabricated in an InGaAsP slab with thickness (T) of 606 nm. Numerical simulation reveals that when T≥800 nm, over 90% of the laser output power couples to the PhC slab modes, suggesting a new route toward an efficient in-plane laser for photonic integrated circuits.     

Internal second harmonic generation in InGaAsP DH lasers

Self induced second harmonic generation (SHG) accompanying 1.3 μm lasing radiation was first observed in fundamental transverse mode InGaAsP DH lasers. Sum frequency generation by two lasing longitudinal modes was observed, which has a conversion factor of four times greater than that for SHG by a single lasing longitudinal mode and predicts the simultaneous laser oscillation of the several longitudinal modes. The estimated second order nonlinear susceptibility of In_0.76Ga_0.24As_0.55 P_0.45 was about 5 × 10^-20 in rotationalized MKS unit, which is at least an order of magnitude greater than that of GaAs.