40 Gb/s非零色散位移光纤传输系统中四种调制格式的性能比较

介绍了四种调制格式即非归零(NRZ),归零(RZ),载波抑制的RZ(CSRZ)和单边带RZ(SSB-RZ),用计算机仿真方法产生了这四种调制格式的40 Gb/s光信号,比较了其波形和光谱.也对这四种调制格式在非零色散位移光纤(NZDSF)上单信道传输进行了仿真,结果表明:在色散完全补偿情况下,RZ,CSRZ和SSB-RZ抗非线性能力都比NRZ强,其中CSRZ最强, CSRZ能够容忍的入纤光功率比NRZ大10.2 dBm;RZ,CSRZ和SSB-RZ 三种格式抗EDFA噪声能力差不多,但都比NRZ强.     

高速相干光通信系统中残留色散均衡器研究

在高速相干光通信系统中,完全使用电子色散补偿时会引入均衡增强相位噪声.本文提出在已有10Gbit/s光纤通信链路上使用电子色散补偿来补偿残留色散的混合色散补偿方案,实现了特定通道100Gbit/s以上高速数据传输.使用虚拟光学仪器软件仿真了在112Gbit/s相干光通信系统中,分别采用有限脉冲响应均衡器和重叠频域均衡器对现有光纤信道进行残留色散补偿后的系统性能.仿真结果表明:相同的抽头长度下,有限脉冲响应均衡器相比重叠频域均衡器有更好的残留色散补偿能力,并且有限脉冲响应均衡器均衡性能更稳定而且计算复杂度更低.因而,有限脉冲响应均衡器相较于重叠频域均衡器更适于混合色散补偿.     

Theoretical Study on Wavelength Conversion Based on Cross Phase Modulation Using Semiconductor Optical Amplifiers

Performances of wavelength converted signal by cross phase modulation (XPM) using semiconductor optical amplifiers (SOA's) were studied by the use of the multi-section model. Results show that they are related to both the phase arm bias current of the XPM wavelength converter and its operation. When the conversion is under the in-phase operation, the peak extinction ratio (ER) and the chirp frequency of the converted signal increase according to the decrease of the phase arm bias current, but the input signal power dynamic range decreases. When the converter is under the out-of-phase operation, the chirp frequency decreases with the decrease of the phase arm bias current, while the peak ER and the input power dynamic range keep almost the same when the phase arm bias current changes.     

基于偏振度的偏振模色散补偿中检测信号对不同归零码型的响应研究

从理论上数值分析和比较了一阶和二阶偏振模色散对各种光调制码型（RZ、CSRZ、RZ-DPSK、CSRZ-DPSK）的偏振模色散的影响,结果表明:不同码型的偏振度大不相同,RZ码受偏振度影响最大,CSRZ-DPSK码受二阶偏振模色散的影响最小,在补偿系统中更适合缓解偏振模色散.     

Optical Filters Using Optical Multi-Layer Structures for Optical Communication Systems

Abstract

In this article, light reflection spectrums for different one-dimensional multi-layer structures are obtained. Optical reflectivities for periodic, superperiodic, and quasiperiodic structures have been calculated using the transfer matrix method. PBGs of each structure have been obtained using the optical reflectivity pattern. From a comparison of reflectivity and standard dense wavelength division multiplexing grids, it is demonstrated that narrow and dense band filters can be built from generalized Fibonacci quasiperiodic structures. Reflectivity of these structures contains bands that meet the ITU-T dense wavelength division multiplexing standard. Reflectivity of other multi-layer structures has poor or less potential to be used in dense wavelength division multiplexing systems.     

光纤通信系统中CSRZ码多级相位调制技术的研究

研究了一种基于CSRZ(载波抑制归零码)的多级相位调制技术在光纤通信系统中的应用.分析了CSRZ、DQPSK(正交差分相移键控)、8DPSK(八差分相移键控)调制格式的特征,理论上推导出了CSRZ-DQPSK和CSRZ-8DPSK的调制解调原理公式,给出了其调制解调方式及具体过程的实现,并用Matlab仿真得到了CSRZ、 CSRZ-DQPSK和CSRZ-8DPSK调制后的频谱图和解调后的眼图.性能分析的结果表明,CSRZ-DQPSK和CSRZ-8DPSK作为新型多级相位调制格式,具有更窄的频谱宽度、更高的频谱效率,因此具有更高的色散、非线性损耗容限和更低的信道间串扰,解调后的眼图性能也很好,有望成为下一代光纤通信系统的首选传输码型.     

用电吸收调制器实现标记擦除的新方法

提出一种结构简单、易于实现的正交光标记擦除的新方法.利用频移键控调制产生80 Gbit/s载荷,采用强度调制产生2.5 Gbit/s标记,然后利用电吸收调制器在分组交换网络核心节点处擦除旧标记,再加入新标记实现信息在网络中继续传输.理论分析和数值模拟验证了此方案擦除标记的可行性.     

光温双控太赫兹波调制特性研究

基于多频带金属开口谐振环结构,利用GaAs材料的光敏特性和VO₂薄膜的热致相变特性,设计了一种既能实现光控又能实现温控的太赫兹(Terahertz, THz)波调制器,研究了光强和薄膜温度对 THz波调制特性的影响。结果表明,随着光强的增加,谐振频率均出现蓝移且谐振强度减小,当光强达到0.2 μJ·cm-2时,第二个谐振点(0.52 THz)蓝移了0.14 THz,透射幅度增加达50%;随着VO₂温度增加至相变温度以上,THz波透射幅度急剧减小,在0.63 THz处透射幅度减小达45.5%;当光强和温度同时控制时,随着光强和温度的增加,谐振点频率蓝移且谐振点处的THz波透射幅度增加,但在温度超过相变温度后,则温度控制起主导作用。设计的THz波调制器能通过光控和温控实现对THz波的明显调制效果,可为实现多功能的THz波功能器件的设计及应用提供参考。     

光纤通信系统中偏振模色散自适应补偿实验研究

成功地研制了光纤通信系统偏振模色散的自适应补偿实验系统.实验中采用特定频率分量功率取样作为反馈信号,采用一种名为PSO(Particle Swarm Optimization)的优化方法作为反馈控制算法.偏振模色散的补偿量达30 ps,自动跟踪补偿时间为1～2 s,实现了准实时自动跟踪补偿.     

利用LED的投影系统光源设计

设计了利用多颗LED(Light Emitting Diode,发光二极管)阵列组成的扩展面光源.经过合理的聚光设计使之符合某些投影设备对亮度要求不是很高,但结构紧凑、性能稳定、使用寿命长的要求.结合数学建模和软件模拟的方式设计了一种小巧的反光杯,利用反光杯把LED近180°的发散光束汇聚到60°左右;然后再用一一对应的透镜阵列汇聚为平行光;最后采用柯勒照明方式把较大的面光源阵列汇集到LCD投影屏幕上,从而达到了较高亮度且具有很高均匀性的目的.     

Photonic mm-Wave Generation Using a Double Passband Fiber Bragg Grating Filter

We report a simplified version of a mm-wave generator employing the sideband filtering technique which uses a single optical sideband filter. Instead of using a Mach-Zehnder-like fiber network to select a pair of sidebands, we employ a single Fabry-Perot fiber Bragg grating with a pair of passbands separated by the mm-wave frequency. Using a single filter eliminated the need for polarization control and pathlength matching that was required by the former interferometer-like arrangement. We describe a 30 GHz generator design and present its mm-wave signal spectrum showing an instrument-limited linewidth of ~20 Hz. The generation of such an extremely narrow signal spectrum from a laser with a 1 MHz linewidth demonstrates the remarkable laser frequency noise cancellation property of the sideband filtering technique.     

WDM Systems in the C-Band Using Er 3+ -Doped Tellurite Optical Waveguide Amplifiers

A 16-channel, 2.5 Gb/s, wavelength-division multiplexing system is analyzed with its channels allocated in the 1.52-1.56 w m wavelength region in order to increase the usable amplifier bandwidth to , 45 nm. To avoid amplified spontaneous emission (ASE) noise and the nonuniform signal gain in the wavelength region, an amplifier module consisting of an Er 3+ -doped tellurite waveguide amplifier, an ASE filter, and two concatenated long-period grating filters are proposed. A tellurite-based amplifier was chosen as the amplifying element because of its broad emission bandwidth (~80 nm), its high emission cross section (6.44 2 10 -25 m 2 ), and its high rare-earth ion solubility. The amplifier model is based on propagation and populationrate equations and includes both uniform and pair-induced up-conversion mechanisms. It is solved numerically by combining finite elements and a Runge-Kutta algorithm. The analysis predicts that using the proposed amplifier module, the channels may be transmitted to a maximum distance of 1800 km, finding applications in large optical networks where either many wavelengths are required or channel spacing must be large.     

大气湍流光PPM通信系统中LDPC码的置信传播译码

对大气弱湍流光PPM通信系统中LDPC码的BP 解码算法进行了研究,提出了相应系统模型下的解码算法.通过理论分析和大量计算机仿真,结果表明:采用LDPC的大气弱湍流光PPM通信系统比未编码的大气弱湍流光PPM通信系统的性能好,但是系统的BER性能随着PPM的时隙数的增加而增大.     

Impact of Modulation Index on Homodyne Crosstalk in Optically Switched Networks

The impact of imperfect modulation depth on crosstalk induced penalty in optical switched systems is theoretically and experimentally investigated. A nonlinear relationship with a clear "knee" is observed, indicating an optimum modulation index of 8 dB.     

相干光OFDM系统中基于导频辅助的采样时钟频率偏差估计和补偿算法

基于导频辅助法,对相干光正交频分复用系统中采样时钟频率偏差进行估计和补偿,并研究了导频的插入位置对该算法补偿效果的影响,通过对五种不同的导频插入位置进行分析和比较,得到最优导频插入位置.仿真结果表明:本文算法即使在较大的频率偏移情况下也有较好的补偿效果,并且采用该方法得到的光信噪比损耗不到1dB,可以有效地降低系统成本;不同导频插入位置对算法的补偿效果会产生影响,在较小采样频率偏移范围内时,导频平均插入方式为最优.如果采样频率偏移量较大,在导频平均插入不能很好地补偿的情况下,导频应尽量插在低频位置.     

光学相干层析成像系统中双通快速扫描光学延迟线的数值分析

以matlab为工具,详尽分析双通快速扫描光学延迟线在最佳耦合条件下的光束传输与分布,为双通快速扫描光学延迟线的设计、元件选择和系统调整提供理论依据.得出离焦距离Δf=1μm和Δf=578 μm两个理论上的最佳耦合点.但就实际光路调试来看,离焦距离Δf=1 μm为此系统的最佳耦合点.     

干涉条纹计数法光纤Fabry-Perot腔液位传感器

提出一种抗光源波动和外界干扰的条纹计数法光纤Fabry-Perot腔干涉型液位传感器.为适应这种条纹计数法对应变大挠度的要求,采用波纹管作应力弹性元件;对干涉条纹走向(或液位升降判向),分别提出实用的硬件设计方案和计算机软件处理办法;给出一种腔长温度补偿设计;实际制作了双光路光纤Fabry-Perot腔液位传感器,进行了实际气压模拟试验和实际水位测量试验,取得了良好结果.     

Optical Solitons in Fibers for Communication Systems

Abstract

A brief history of attempts to use solitons for optical fiber communications and of the technical developments toward making soliton transmission practical is reviewed. The main problems affecting long-distance soliton transmission, as well as techniques to solve them, are described. Recent developments concerning the use of dispersion management and some of the remarkable properties of dispersion managed solitons are also discussed.