在线微孔膜双萃取-流动注射光度法测定水中阴离子表面活性剂的研究

采用在线微孔膜双萃取-流动注射光度法测定了水中的阴离子表面活性剂.方法基于亚甲基蓝与阴离子表面活性剂作用生成的盐类(λ_(max)=650 nm),可被氯仿萃取,采用在线双微孔膜液液萃取相分离器,优化了流路参数、萃取模块的流路尺寸和微孔膜的孔径.方法的线性范围为25～1000 μg/L,线性相关系数r≥0.999;检出限为4.3 μg/L;不同浓度的相对标准偏差(n=7)为0.7%～6.0%;实际水样的加标回收率为96%～110%;样品测定频率为18样/h.利用本方法分别测定了2个实际水样和2个国家标准参考物质中的阴离子表面活性剂,结果令人满意.     

在线液液液微萃取-电动流动分析系统测定水中挥发酚类化合物总量

采用在线液液液微萃取(LLLME)富集净化和电动流动分析(EFA)系统测定水中挥发酚类化合物折合苯酚总量.EFA系统由一台自制电渗泵和4个电磁切换阀组成,计算机控制泵运作和阀切换.结果表明:在聚丙烯中空纤维膜壁上涂十二醇液膜,管内充10 μL 0.25 mol/L NaOH反萃液,试样以2.0 mL/min流量流经萃取通道7.5次循环,1.0 mL样品体积的富集倍数为53,分析时间为 9 min,挥发酚类化合物折合浓度线性范围为9.4×10-3～5.7 mg/L苯酚,检出限为3 μg/L苯酚,远低于一和二级污水排放中挥发酚类化合物的最大允许量;6.0 mL样品体积的富集倍数为300,挥发酚类化合物折合浓度线性范围为1.7×10-3～1.0 mg/L苯酚,检出限为0.6 μg/L苯酚,低于Ⅰ和Ⅱ类地面水中挥发酚类化合物的最大允许量.     

支撑液膜在线萃取富集流动注射分光光度法测定水中的痕量铅

研究了以双硫腙为流动载体,煤油为膜溶剂的支撑液膜萃取体系,建立了支撑液膜在线萃取富集流动注射分光光度法测定水中痕量铅(Ⅱ)的新方法。优化了支撑液膜萃取富集条件,优化结果为:试样pH=6,反萃液柠檬酸浓度为0.5 mol/L,载体双硫腙浓度为0.03%,膜孔径为0.3μm,富集时间为30 m in。在此条件下,方法的检出限为0.2μg/L;线性范围为0.5~100μg/L。应用于自来水、河水和工业污水中铅(Ⅱ)的检测,结果满意。     

电化学液相微萃取-循环伏安法对海带中溴的测定

将液相微萃取与电化学法相结合,建立了快速测定海带中溴含量的电化学液相微萃取-循环伏安法(ELPME-CV).苯甲酸乙酯作为粘结剂组成碳糊电极,同时充当微液膜萃取相与样品溶液接触.在正电位下,溴离子被氧化成溴分子,溴分子经微液膜萃取富集,在负电位下还原溶出.在0.01 ～0.50 mmol/L范围内,溴的还原峰电流与溶液中溴离子浓度成正比,检出限为0.05 mmol/L.测定市售海带中溴的含量为91 μg/g,相对标准偏差为11%.     

三相中空纤维膜液相微萃取-高效液相色谱法测定水中痕量双酚A

建立了三相中空纤维膜液相微萃取-高效液相色谱(HF-LPME-HPLC)方法,用于分析测定水中痕量双酚A的含量.设计了三相中空纤维膜液相微萃取系统,优化的HP-LPME最佳萃取条件为:萃取剂为正辛醇,接受相NaOH浓度为0.09 mol/L,样品溶液pH=4.0,NaC1加入量为30 g/L,搅拌速度为900 r/min,萃取时间为60 min.萃取后取20 μL接受相进行色谱分析.在最佳萃取条件下,方法的线性范围为0.5～200 μg/L(r＞ 0.999),检出限(信噪比为3)为0.2 μg/L;富集因子为241;方法RSD＜3.2％ (n=3).在实际环境水样中添加5,20和50μg/L的双酚A标准物质,加标平均回收率为92.8％～101.9％.表明本方法可用于水中痕量双酚A的快速准确测定.     

凝固-漂浮分散液液微萃取-高效液相色谱法测定水样中氯酚

采用凝固-漂浮分散液液微萃取(SFO-DLLME)-高效液相色谱法测定水样中3种氯酚.以密度小于水,且凝固点为24 ℃的1-十二醇为萃取剂,甲醇为分散剂,对水样进行分散液液微萃取.将混合液离心,再通过冷冻凝固操作使漂浮的萃取剂和水相分离,萃取剂复溶后进样测定.本实验确定的最佳实验条件为:萃取剂200 μL、分散剂300 μL、1.2 g NaCl、1 mol/L H3PO4 200 μL、样品体积8.0 mL、萃取时间3 min.3种氯酚测定的线性范围为0.05～6.0 mg/L;检出限为20～38 μg/L.应用本方法分析实际水样,加标回收率在90.11%～107.7%之间;日间相对标准偏差在3.5%～4.6%之间.本方法扩展了分散液液微萃取萃取剂的选择范围,具有简便、快速、准确、环境友好等特点.     

液液萃取-分散液液微萃取-气相色谱-质谱联用测定纺织废水中痕量禁用偶氮染料

建立了液液萃取-分散液液微萃取-气相色谱-质谱联用技术测定纺织废水中痕量偶氮染料的方法。废水中的偶氮染料在碱性条件下经连二亚硫酸钠还原成芳香胺后,先用叔丁基甲醚液液萃取、盐酸反萃进行预浓缩及净化;再以乙腈-氯苯体系进行分散液液微萃取,气相色谱-质谱测定。对前处理条件进行了优化,考察了酸碱度及盐效应对芳香胺萃取效率的影响,结果表明：液液萃取过程中加入30 g NaCl,分散液液微萃取过程中加入1 mL 5 mol/L的NaOH调节体系至碱性才能达到较好的萃取效率。在优化的实验条件下,21种目标物均呈现良好的线性关系,其中13种芳香胺的线性范围为0.05~10 μg/L,7种芳香胺的线性范围为0.05~5 μg/L,2,4-二氨基苯甲醚的线性范围为20~100 μg/L,相关系数为0.996~0.999。20种芳香胺的检出限可达0.05 μg/L,2,4-二氨基苯甲醚检出限为20 μg/L。印染、机织、印花等实际废水加标试验表明,方法的回收率为75.6%~115.1%。该方法富集倍数高,检出限低,适用于纺织废水中痕量禁用偶氮染料的检测。     

液-液-液微萃取/高效液相色谱法测定人血浆中的西地那非和伐地那非

建立了液-液-液微萃取与高效液相色谱联用同时测定血浆中西地那非和伐地那非的方法。考察了萃取溶剂、溶剂体积、接受相液滴大小、搅拌速度和萃取时间等因素对富集因子的影响,得到了萃取溶剂为300 μL 甲苯、接受相为2 μL 0.2 mol/L HCl、搅拌速度为600 r/min和萃取时间为40 min的最佳实验条件。在该条件下,获得了较高的富集因子。两种组分的线性范围均为5 μg/L~1.0 mg/L,加标回收率高于87%,其相对标准偏差小于5%。以信噪比为3计,西地那非的检测限为1 μg/L,伐地那非为0.5 μg/L。该方法能有效地去除复杂基体的干扰,有机溶剂消耗少,萃取效率高,是一种有效的、灵敏的样品前处理方法,适用于血浆中微量西地那非和伐地那非的测定。     

环境水样中百菌清残留的单滴微萃取-反相液相色谱测定

应用单滴微萃取(SDME)-反相液相色谱(RPLC)检测了环境水样中的百菌清残留.优化了单滴微萃取条件:环己烷萃取剂6 μL、单滴体积2 μL、搅拌速率350 r/min、萃取时间40 min、水溶液温度35 ℃、无盐度.水样经单滴微萃取后,使用Hypersil C18柱反相液相色谱分离测定百菌清.反相液相色谱条件:100%甲醇流动相、流速1.0 mL/min、柱温25 ℃、224 nm检测.方法的线性范围、检出限、相对标准偏差和富集倍数分别为1.0 ～50 μg/L、0.02 μg/L、6.1%和427倍.采用该法对环境水样中的百菌清残留进行了测定,环境水样的加标回收率为98% ～106%.     

环境水样中己烯雌酚与双烯雌酚的离子液体分散液-液微萃取/高效液相色谱法测定

以离子液体([Omim][PF6])为萃取剂,采用冷诱导分散液-液微萃取对环境水样中的己烯雌酚和双烯雌酚残留进行富集.优化后的萃取条件:在pH 3.0的条件下,以50 μL离子液体为萃取剂,0.8 mL甲醇为分散剂,采用反相 Extend-C18柱(5 μm, 250 mm×4.6 mm),流动相为水-甲醇(体积比40 ∶ 60),流速:1.0 mL/min,柱温:35 ℃,检测波长:245 nm.在优化的萃取条件下,己烯雌酚和双烯雌酚的线性范围均为2.5 ～200 μg/L,检出限(S/N=3)为80 ng/L.应用于环境水样中己烯雌酚和双烯雌酚的检测,加标回收率为93% ～98%,相对标准偏差为3.0% ～5.4%,建立的方法简单、环保.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.