Surface-modified TiO(2) nanoparticles as affinity probes and as matrices for the rapid analysis of phosphopeptides and proteins in MALDI-TOF-MS

We utilized three different types of TiO₂ nanoparticles (NPs) namely TiO₂‐dopamine, TiO₂‐CdS and bare TiO₂ NPs as multifunctional nanoprobes for the rapid enrichment of phosphopeptides from tryptic digests of α‐ and β‐casein, milk and egg white using a simplified procedure in MALDI‐TOF‐MS. Surface‐modified TiO₂ NPs serve as effective matrices for the analysis of peptides (gramicidin D, HW6, leucine‐enkephalin and methionine‐enkephalin) and proteins (cytochrome c and myoglobin) in MALDI‐TOF‐MS. In the surface‐modified TiO₂ NPs‐based MALDI mass spectra of these analytes (phosphopetides, peptides and proteins), we found that TiO₂‐dopamine and bare TiO₂ NPs provided an efficient platform for the selective and rapid enrichment of phosphopeptides and TiO₂‐CdS NPs efficiently acted as the matrix for background‐free detection of peptides and proteins with improved resolution in MALDI‐MS. We found that the upper detectable mass range is 17 000 Da using TiO₂‐CdS NPs as the matrix. The approach is simple and straightforward for the rapid analysis of phosphopeptides, peptides and proteins by MALDI‐MS in proteome research.     

Use of MALDI-TOF MS to Discriminate between Aflatoxin B1-Producing and Non-Producing Strains of Aspergillus flavus

Aflatoxin B₁ (AFB₁) is one of the most toxic mycotoxins. One of the producers of AFB₁ is Aspergillus flavus. Therefore, its rapid identification plays a key role in various sectors of the food and feed industry. MALDI-TOF mass spectrometry is one of the fastest and most accurate methods today. Therefore, the aim of this research was to develop the rapid identification of producing and non-producing strains of A. flavus based on the entire mass spectrum. To accomplish the main goal a different confirmatory MALDI-TOF MS and TLC procedures such as direct AFB₁ identification by scraping from TLC plates, A. flavus mycelium, nutrient media around A. flavus growth, and finally direct AFB₁ identification from infected wheat and barley grains had to be conducted. In this experiment, MALDI-TOF mass spectrometry with various modifications was the main supporting technology. All confirmatory methods confirmed the presence of AFB₁ in the samples of aflatoxin-producing strains of A. flavus and vice versa; AFB₁ was not detected in the case of non-producing strains. Entire mass spectra (from 2 to 20 kDa) of aflatoxin-producing and non-producing A. flavus strains were collected, statistically analyzed and clustered. An in-depth analysis of the obtained entire mass spectra showed differences between AFB₁-producing and non-producing strains of A. flavus. Statistical and cluster analysis divided AFB₁-producing and non-producing strains of A. flavus into two monasteries. The results indicate that it is possible to distinguish between AFB₁ producers and non-producers by comparing the entire mass spectra using MALDI-TOF MS. Finally, we demonstrated that if there are established local AFB₁-producing and non-producing strains of A. flavus, the entire mass spectrum database identification of aflatoxigenic A. flavus strains can be even faster and cheaper, without the need to identify the toxin itself.     

Surface modified silver selinide nanoparticles as extracting probes to improve peptide/protein detection via nanoparticles-based liquid phase microextraction coupled with MALDI mass spectrometry

We report the first use of functionalized Ag₂Se nanoparticles (NPs) as effective extracting probes for NPs-based liquid-phase microextraction (NPs-LPME) to analyze hydrophobic peptides and proteins from biological samples (urine and plasma) and soybean in matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS). Surface modified functional groups such as octadecanethiol (ODT) and 11-mercaptoundecanoic acid (MUA) on Ag₂Se NPs were found to play an important role for efficient extraction of peptides and proteins from test samples through hydrophobic interactions. The peptides can be efficiently extracted using functionalized Ag₂Se NPs as extracting probes in the presence of high concentration of matrix interferences such as 4 M urea, 0.5% Triton X-100 and 3% NaCl. Ag₂Se@ODT NPs have shown better extraction efficiency and detection sensitivity for peptides than Ag₂Se@MUA NPs, bare Ag₂Se NPs and conventional MALDI-MS. The LODs are 20-68 nM for valinomycin and 100-180 nM for gramicidin D using Ag₂Se@ODT NPs-LPME in the MALDI-MS. The current approach is highly sensitive and the target analytes can be effectively isolated without sample loss and efficiently analyzed in MALDI-MS.     

Ferrite nanoparticles (MFe2O4 NPs) as magnetically recoverable supports for catalysis in organic synthesis

Abstract

Heterogenization of organic and metallic catalysts with a solid support is an attractive and useful strategy to solve the separation and recovery problems of catalysts. During the last decade, magnetic nanoparticles (MNPs) in general ferrite nanoparticles (MFe₂O₄ NPs) have emerged as a highly efficient support for catalysis, due to their simple fabrication, modification, and large surface area ratio. In this paper, we provide an overview of the utilization of organic and metallic molecules immobilized on magnetic ferrite nanoparticles (MFe₂O₄ NPs) as attractive and efficient catalytic systems in wide variety of in organic reactions.     

Fe3O4 nanoparticles as the adsorbent of magnetic solid-phase extraction for clean and preconcentration of maltol and ethyl maltol in food samples followed by HPLC analysis

In this work, a magnetic solid-phase extraction protocol followed with high-performance liquid chromatography analysis was developed for the determination of maltol and ethyl maltol in food samples. The Fe₃O₄ nanoparticles were prepared by one-step hydrothermal method and was used as adsorbent for clean and preconcentrated maltol and ethyl maltol in food samples. The as-prepared Fe₃O₄ nanoparticle was characterized by transmission electron microscope, Fourier transform infrared spectroscopy, X-ray diffraction, and vibrating sample magnetometer. The extraction conditions including the amount of material, extraction time, pH, temperature, and desorption solvents were investigated, respectively. Under the optimized conditions, the detection limits of 0.04 and 0.05?µg?mL^?1 could be achieved for maltol and ethyl maltol. The recoveries between 84.2 and 103.4% with RSDs lower than 2.30% were obtained for the analysis of spiked plum candy sample. The developed method was successfully applied to the analysis of real samples, such as juice, chocolate, and plum candy.     

In-bone protein digestion followed by LC-MS/MS peptide analysis as a new way towards the routine proteomic characterization of human maxillary and mandibular bone tissue in oral surgery

Proteomic characterization of alveolar bones in oral surgery represents an analytical challenge due to their insoluble character. The implementation of a straightforward technique could lead to the routine use of proteomics in this field. This work thus developed a simple technique for the characterization of bone tissue for human maxillary and mandibular bones. It is based on the direct in-bone tryptic digestion of proteins in both healthy and pathological human maxillary and mandibular bone samples. The released peptides were then identified by the LC-MS/MS. Using this approach, a total of 1120 proteins were identified in the maxillary bone and 1151 proteins in the mandibular bone. The subsequent partial least squares–discrimination analysis (PLS-DA) of protein data made it possible to reach 100% discrimination between the samples of healthy alveolar bones and those of the bone tissue surrounding the inflammatory focus. These results indicate that the in-bone protein digestion followed by the LC-MS/MS and subsequent statistical analysis can provide a deeper insight into the field of oral surgery at the molecular level. Furthermore, it could also have a diagnostic potential in the differentiation between the proteomic patterns of healthy and pathological alveolar bone tissue. Data are available via ProteomeXchange with the identifier PXD026775.     

Cuprous oxide nanospheres as probes for light scattering imaging analysis of live cells and for conformation identification of proteins

A facile solution-phase synthesis route of highly uniform Cu₂O nanospheres (Cu₂O NPs) with the size of 57.7 ± 4.7 nm was developed, and then the nanoparticles were applied to live cell imaging under a common dark-field microscope. Starting from copper(II) salts, the synthesis of Cu₂O NPs was made in the presence of cetyltrimethylammonium bromide (CTAB) by reducing the copper(II) with sodium borohydride (NaBH₄) in aqueous medium and by aging process in the air. Monitoring of morphology evolution process of Cu₂O NPs with scanning electron microscopy (SEM) and measuring of the UV-visible spectra showed that the synthesis of Cu₂O NPs follows the reduction-oxidation coupled process of Cu²⁺ into Cu⁰ species at first and then the resulted Cu⁰ species into Cu₂O NPs in the air. Light scattering (LS) features have been measured with a common spectrofluorometer and a common dark-field microscope, and it was found that the as-prepared Cu₂O NPs display strong blue scattering light and can be applied for cell imaging. If incubated with human bone marrow neuroblastoma, transferrin-conjugated Cu₂O NPs can get into the cells and show strong pure blue light in cytoplasm. Further investigations showed that the Cu₂O NPs could be applied for probes for conformation of proteins.     

Cobalt oxide nanoparticles as a novel high-efficiency fiber coating for solid phase microextraction of benzene,toluene, ethylbenzene and xylene from aqueous solutions

In this work cobalt oxide nanoparticles were introduced for preparation of a novel solid phase microextraction (SPME) fiber coating. Chemical bath deposition (CBD) technique was used in order for synthesis and immobilization of the Co₃O₄ nanomaterials on a Pt wire for fabrication of SPME fiber. The prepared cobalt oxide coating was characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The fiber was evaluated for the extraction of benzene, toluene, ethylbenzene and xylene (BTEX) in combination with GC–MS. A simplex optimization method was used to optimize the factors affecting the extraction efficiency. Under optimized conditions, the proposed fiber showed extraction efficiencies comparable to those of a commercial polydimethylsiloxane (PDMS) fiber toward the BTEX compounds. The repeatability of the fiber and its reproducibility, expressed as relative standard deviation (RSD), were lower than about 11%. No significant change was observed in the extraction efficiency of the new SPME fiber after over 50 extractions. The fiber was successfully applied to the determination of BTEX compounds in real samples. The proposed nanostructure cobalt oxide fiber is a promising alternative to the commercial fibers as it is robust, inexpensive and easily prepared.     

Fe3O4/poly (acrylic acid) nanoparticles as modifiers for improving rheological and filtration properties of water-based drilling fluids

Drilling fluid is a vital element and is often regarded as the “blood” in the oil industry. Although traditional oil-based drilling fluids have advantages in some harsh cases, the high cost and environmental pollution faced with them limit its application. Water-based drilling fluids (WBDFs) with environmental friendly, low cost, and high performance are important for drilling engineering to solve the problems of low efficiency and wellbore instability caused by poor rheological properties and large filtration loss in drilling operations. In this paper, Fe₃O₄ nanoparticles modified by poly (acrylic acid) (PAA) through 3-(trimethoxysilyl) proryl methacrylate (TMSPMA) were introduced into WBDFs for enhancing their rheological and plugging performance. Rheological tests indicated that the consistency coefficient (K) of the Fe₃O₄/PAA nanoparticles/WBDFs decreased at a higher concentration. Incorporated nanoparticles with a concentration of 0.05?wt %, the WBDFs will exhibit good shear-thinning behavior. The results showed that the best performance for Fe₃O₄/PAA nanoparticles being as a filtration additive in WBDFs was achieved at concentration as low as 0.1?wt %. These results demonstrated that Fe₃O₄/PAA nanoparticles are effective additives for WBDFs.     

Combination of AlCl3, Ionic Liquid,and Microwaves: An Efficient Method for Dehydration and 1,3-Dipolar Cycloaddition: An Unusual Observation in the Presence of Acrylonitrile

Use of a combination of ionic liquids in the presence of aluminium chloride and microwave irradiation was shown to be a very efficient and high-yielding method for the dehydration of aldoximes and also for 1,3-dipolar cycloadditions. Surprisingly, the presence of acrylonitrile rendered an unusual formation of substituted amide.     

Anchored complexes of Ni,Pt, and Pd on Fe3O4 nanoparticles as new and eco-friendly nanocatalysts in Suzuki and Heck coupling reactions

Abstract

Three recoverable nanocatalysts were developed by immobilizing Ni, Pt, and Pd Schiff-base complexes on the magnetite nanoparticles. Successful preparation of the nanocatalysts was evidenced by Fourier transform infrared (FT-IR) and energy dispersive X-ray (EDX) spectroscopy. Nano-sized spherical structure of the nanocatalysts was indicated by scanning electron microscopy (SEM). X-ray powder diffraction (XRD) determined that the crystalline cubic spinel structure of Fe₃O₄ remained constant through the synthesis of three complexes on Fe₃O₄ nanoparticles. Magnetic properties of the nanocatalysts were analyzed by the vibration sample magnetometer (VSM). Thermostability of the nanocatalysts was studied by thermogravimetric analysis (TGA). Metal loading of these nanocatalysts was evidenced by inductively coupled plasma atomic emission (ICP-AES).

Investigating the catalytic activity of these nanocatalysts in Suzuki and Heck reactions implicated that in the presence of Pd nanocatalyst coupling reactions proceeded efficiently. For Pt nanocatalyst, Suzuki reaction took place in longer time with moderate to good yield. For the Heck reaction, the desired products were achieved only for aryl iodide and some aryl bromides. The Ni nanocatalyst could just catalyze the Suzuki reaction.

Relying on the magnetic characteristic, these nanocatalysts could be simply recovered and reused several cycles without significant loss in catalytic activity.     

基于碳酸钙-金纳米粒子无机杂化复合物固定硫堇的新方法及其在过氧化氢传感器中的应用

通过静电作用,经碳酸钙-金纳米粒子(CaCO3-AuNPs)无机杂化复合物实现了电活性物质硫堇(Th)在金电极表面的有效固定.AuNPs静电吸附到CaCO3微球表面形成CaCO3-AuNPs无机杂化复合物,该杂化复合物具有微孔结构、大的表面积和好的生物相容性,使得Th的固定量和稳定性大大提高.探讨了Th修饰电极在过氧化...     

Macrocyclic ZnII and CuII complexes as guests of the hybrid composites based on the layered MnPS3 phase. Comparison of spectroscopic properties

A family of macrocyclic complexes [M₂LⁿCl₂] have been synthesized and characterized (M: Cu^II or Zn^II; Lⁿ: macrocyclic ligand derived from 2-hydroxy-5-methyl-1,3-benzenedicarbaldehyde and different aliphatic diamines and o-phenylenediamine). The influence of the aromaticity of the ligand and the metal center on the spectroscopic properties of the complexes (absorption and emission) has been studied. Making use of the weak interactions between hydrated potassium ions and the layers of the K_0.4Mn_0.8PS₃ precursor, the obtained macrocyclic complexes have been intercalated in the interlamellar space by a microwave assisted cationic exchange reaction. The optical properties of the obtained hybrid materials are reported. The absorption edge, recorded by solid state reflectance spectroscopy for Cu^II and the Zn^II macrocycle-based composites, is 1.67–1.76 eV, both shifted to lower energy compared with that of the pristine MnPS₃.     

Magnetic solid-phase extraction based on Fe3O4/graphene oxide nanoparticles for the determination of malachite green and crystal violet in environmental water samples by HPLC

This work describes a magnetic Fe₃O₄/graphene oxide (GO)-based solid-phase extraction (MSPE) technique for high performance liquid chromatography (HPLC) detection of malachite green (MG) and crystal violet (CV) in environmental water samples. Fe₃O₄/ GO magnetic nanoparticles were synthesised by a chemical co-precipitation method and characterised by scanning electron micrograph, transmission electron microscope, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and surface area analyser. The prepared Fe₃O₄/GO magnetic nanoparticles were used as the adsorbents of MSPE for MG and CV. By coupling with HPLC, a sensitive and cost-effective method for simultaneous determination of MG and CV was developed. The important parameters including the amount of Fe₃O₄/GO, pH of the sample solution, extraction time, salt effect, the type and volume of desorption solvent were investigated in detail. Under optimised conditions, the calibration curves were linear in the concentration range of 0.5–200 μg L^?1, and the limits of detection were 0.091 and 0.12 μg L^?1 for MG and CV, respectively. Finally, the established MSPE-HPLC method was successfully applied to determine MG and CV in environmental water samples with the recoveries ranging from 91.5% to116.7%.     

Oxoperoxo tungsten(VI) complex immobilized on Schiff base-modified Fe3O4 magnetic nanoparticles as a heterogeneous catalyst for oxidation of alcohols with hydrogen peroxide

Oxoperoxo tungsten(VI) complex immobilized on Schiff base-modified Fe₃O₄ super paramagnetic nanoparticles were synthesized and appropriately characterized using FT-IR, XRD, SEM, TEM, EDX, BET, and VSM analysis. The synthesized nanoparticles efficiently catalyzed oxidation of benzylic alcohols with H₂O₂ as oxidant in high yields, with high to excellent selectivity. The catalyst can be recovered using an external magnetic field and recycled for subsequent oxidation reactions without any appreciable loss of efficiency. The simple preparation, high activity, excellent selectivity, and simple recoverability of the catalyst are advantageous.     

Novel thionin-functionalised core shell magnetic nanoparticles for dispersive solid-phase extraction of Hg(II) in food and water samples

To develop an accurate and precise method for separation and pre-concentration of Hg(II), a novel thionin functionalised core shell structure magnetic material has been prepared and characterised. The extraction ability of the material was evaluated by magnetic solid-phase extraction coupled with inductively coupled plasma mass spectrometry determination of Hg(II) in food and water samples. Combining the advantages of magnetic separation with selective extraction of thionin towards Hg(II), the material exhibits enhanced enrich selectivity and efficiency for Hg(II). The experimental parameters influencing Hg(II) extraction efficiency, including pH of the aqueous solution, the dosage of the adsorbent, extraction time and sample volume, were systematically investigated. Under the optimised conditions, concentration of Hg(II) at 1.0 μg L^?1 can be successfully enriched by the material without the interference of the common co-existing ions. The enrichment factor and adsorption capacity were 250 and 75.2 mg g^?1, and precise of the method was confirmed by analysing the spiked food, water samples and standard water reference samples with the recoveries of 92.5–101.8%.     

Highly Dispersed Vanadia Anchored on Protonated g-C3N4 as an Efficient and Selective Catalyst for the Hydroxylation of Benzene into Phenol

The direct hydroxylation of benzene is a green and economical-efficient alternative to the existing cumene process for phenol production. However, the undesired phenol selectivity at high benzene conversion hinders its wide application. Here, we develop a one-pot synthesis of protonated g-C₃N₄ supporting vanadia catalysts (V-pg-C₃N₄) for the efficient and selective hydroxylation of benzene. Characterizations suggest that protonating g-C₃N₄ in diluted HCl can boost the generation of amino groups (NH/NH₂) without changing the bulk structure. The content of surface amino groups, which determines the dispersion of vanadia, can be easily regulated by the amount of HCl added in the preparation. Increasing the content of surface amino groups benefits the dispersion of vanadia, which eventually leads to improved H₂O₂ activation and benzene hydroxylation. The optimal catalyst, V-pg-C₃N₄-0.46, achieves 60% benzene conversion and 99.7% phenol selectivity at 60 ^oC with H₂O₂ as the oxidant.     

Synthesis and application of polythiophene-coated Fe3O4 nanoparticles for preconcentration of ultra-trace levels of cadmium in different real samples followed by electrothermal atomic absorption spectrometry

In this research, magnetic Fe₃O₄ nanoparticles were synthesised by co-precipitation method and modified with polythiophene (PT) to produce Fe₃O₄-PT nanoparticles for preconcentration and determination of cadmium (??) ion followed by electrothermal atomic absorption spectrometry. The results of FT-IR spectroscopy, EDX analysis and SEM images show that Fe₃O₄-PT nanoparticles were synthesised successfully. Different parameters such as sample pH, amounts of adsorbent, sample volume, extraction time, type and concentration of eluent and desorption time were completely investigated and optimum conditions were selected.

Under the optimum conditions, the calibration curve was linear in the range of 0.01–0.25 µg L^?1 of cadmium (??). The relative standard deviation was 4.7% (n = 7, 0.10 µg L^?1 Cd²⁺) and limit of detection was 3.30 ng L^?1. The accuracy of the proposed method was verified by the analysis of a certified reference material and spike method. Finally, the proposed method was applied for the determination of ultra-trace levels of cadmium (??) in different water and food samples.     

Dependence of size and size distribution on reactivity of aluminum nanoparticles in reactions with oxygen and MoO3

The oxidation reaction of aluminum nanoparticles with oxygen gas and the thermal behavior of a metastable intermolecular composite (MIC) composed of the aluminum nanoparticles and molybdenum trioxide are studied with differential scanning calorimetry (DSC) as a function of the size and size distribution of the aluminum particles. Both broad and narrow size distributions have been investigated with aluminum particle sizes ranging from 30 to 160 nm; comparisons are also made to the behavior of micrometer-size particles. Several parameters have been used to characterize the reactivity of aluminum nanoparticles, including the fraction of aluminum that reacts prior to aluminum melting, heat of reaction, onset and peak temperatures, and maximum reaction rates. The results indicate that the reactivity of aluminum nanoparticles is significantly higher than that of the micrometer-size samples, but depending on the measure of reactivity, it may also depend strongly on the size distribution. The isoconversional method was used to calculate the apparent activation energy, and the values obtained for both the Al/O₂ and Al/MoO₃ reaction are in the range of 200-300 kJ/mol.