Novel Ag ion-selective electrodes based on two new mixed azathioether crowns containing a 1,10-phenanthroline sub-unit

Novel polymeric membrane (PME) and coated graphite (CGE) silver-selective electrodes based on two recently synthesized mixed azathioether crowns containing a 1,10-phenanthroline sub-unit were prepared. The electrodes reveal a Nernstian behavior over quite wide Ag⁺ ion concentration ranges with a very low limits of detection (LOD) (i.e. down to 1.0×10⁻⁸ M for CGEs and 8.0×10⁻⁷ M for PMEs). The potentiometric responses are independent of the pH of the test solution in the pH range 3.0-7.0. The electrodes possess advantages of low resistance, very fast response time, relatively long lifetimes and, especially, good selectivities relative to a wide variety of other cations. The electrodes were used, as indicator electrodes, in the potentiometric titration of silver ion and in the determination of Ag⁺ in waste water, photographic emulsion and radiographic and photographic films.     

Novel potentiometric and optical silver ion-selective sensors with subnanomolar detection limits

Ten Ag⁺-selective ionophores have been characterized in terms of their potentiometric selectivities and complex formation constants in solvent polymeric membranes. The compounds with π-coordination show much weaker interactions than those with thioether or thiocarbamate groups as the coordinating sites. Long-term studies with the best ionophores show that the lower detection limit of the best Ag⁺ sensors can be maintained in the subnanomolar range for at least 1 month. The best ionophores have also been characterized in fluorescent microspheres. The so far best lower detection limits of 3 × 10⁻¹¹ M (potentiometrically) and 2 × 10⁻¹¹ M Ag⁺ (optically) are found with bridged thiacalixarenes.     

Comparative study of Ag(I) selective poly(vinyl chloride) membrane sensors based on newly developed Schiff-base lariat ethers derived from 4,13-diaza-18-crown-6

The six Schiff-base lariat ether chelates based on 4,13-diaza-18-crown ether, have been synthesized and explored as a neutral ionophores for preparing poly(vinyl chloride) based membrane sensors selective to silver(I). The addition of potassium tetrakis(4-chlorophenyl) borate and various plasticizers, viz., o-NPOE, DBP, DBBP, DOP and CN has been found to substantially improve the performance of the sensors. The best performance was obtained with the sensor no. 5 having membrane of chelate (A₆) with composition (w/w) chelate (2.8%):PVC (45.7%):o-NPOE (48.6%):KTpClPB (2.8%). This sensor exhibits Nernstian response with slope 59.3 mV/decade of activity in the concentration range 5.6 × 10⁻⁸-1.0 × 10⁻¹ M Ag(I), performs satisfactorily over wide pH range of (3.0-8.0) with a fast response time (12 s). The sensor was also found to work satisfactorily in partially non-aqueous media up to 25% (v/v) content of acetonitrile, methanol or ethanol and can tolerate the concentration 1.0 × 10⁻² M of ionic (SDS, TBC) and nonionic (Triton X-100) surfactants. The proposed sensor can be used over a period of 4 months without significant drift in potentials. The response of the sensor was highly selective to Ag⁺ over a large number of cations and it could therefore be used for Ag⁺ estimation in blood of occupationally exposed persons.     

Silver ion imprinted polymer nanobeads based on a aza-thioether crown containing a 1,10-phenanthroline subunit for solid phase extraction and for voltammetric and potentiometric silver sensors

A new nano-sized silver(I) ion-imprinted polymer (IIP) was prepared via precipitation copolymerization using ethyleneglycol dimethacrylate, as a cross-linking agent in the presence of Ag⁺ and an aza-thioether crown containing a 1,10-phenanthroline subunit as a highly selective complexing agent. The imprint silver(I) ion was removed from the polymeric matrix using a 1.0 M HNO₃ solution. The resulting powder material was characterized using IR spectroscopy and scanning electron microscopy. The SEM micrographs showed colloidal nanoparticles of about 52 nm and 75 nm in diameter and slightly irregular in shape for leached and unleached IIPs, respectively. The optimal pH for quantitative enrichment was 6.0 and maximum sorbent capacity of the prepared IIP for Ag⁺ was 18.08 μmol g⁻¹. The relative standard deviation and limit of detection (LOD = 3S_b/m) for flame atomic absorption spectrometric determination of silver(I) ion, after its selective extraction by the prepared IIP nanobeads, were evaluated as 2.42% and 2.2 × 10⁻⁸ M, respectively. The new Ag⁺-IIP was also applied as a suitable sensing element to the preparation of highly selective and sensitive voltammetric and potentiometric sensors for ultra trace detection of silver(I) ion in water samples, with limits of detection of 9.0 × 10⁻¹⁰ and 1.2 × 10⁻⁹ M, respectively.     

A flow injection analysis system for monitoring silver (I) ion and iodine residuals in recycled water from recovery systems used for spaceflight

A laboratory-built flow injection analyzer is reported for monitoring the drinking water disinfectants silver (I) ion and iodine in water produced from NASA's water recovery system. This analyzer uses spectrophotometric detection with a custom made 10 cm optical flow cell. Optimization and interference studies are discussed for the silver (I) ion configuration. Subsequent results using the silver (I) configuration with minor modifications and alternative reagents gave promising results for iodine determinations as well. The estimated MDL values for Ag⁺ and I₂ are 52 μg L⁻¹ Ag⁺ and 2 μg L⁻¹ I₂; the mean percent recoveries were 104% and 96.2% for Ag⁺ and I₂ respectfully; and percent relative standard deviations were estimated at 1.4% for Ag⁺ and 5.7% for I₂. The agreement of this potentially multifunctional analyzer to reference methods for each respective water disinfectant is measured using Bland–Altman analysis as well as more traditional estimates.     

PVC membrane electrode based on triheptyl dodecyl ammonium iodide for the selective determination of molybdate(VI)

Novel polyvinyl chloride (PVC) membrane electrodes based on triheptyl dodecyl ammonium iodide have been developed. In the presence of 12.5 mM H₂O₂, these electrodes are capable of determining molybdate(VI) ion. The electrodes exhibit near-Nernstian responses over a wide concentration range (2.0 × 10⁻⁶ to 5.0 × 10⁻³ M). The proposed electrodes demonstrate satisfying selectivity for molybdate(VI) ion in the presence of a wide variety of anions other than iodide, and can be used in the pH range 5.0-7.0. Moreover, the electrodes show an average response time of 2-3 min and can be used over a period of 2 months without any significant deviation being observed. In the light of our results, the response mechanism of the electrode is discussed and HMoO₂(O₂)₂⁻ is suggested as the response ion. The proposed electrode has been used to measure molybdenum in ore samples, and the results were in agreement with those obtained by means of ICP analysis.     

Preparation and properties of a new solid state borate ion selective electrode and its application

A new borate ion selective electrode using solid salts of Ag₃BO₃, Ag₂S and Cu₂S has been developed. Detailed information is provided concerning the composition, working pH and conditioning of the electrode. An analytically useful potential change occurred from 1 × 10⁻⁶ to 1 × 10⁻¹ M borate ion. The slope of the linear portion was 31 ± 2 mV/10-fold changes in borate concentration. The measurements were made at constant ionic strength (0.1 M NaNO₃) and at room temperature. The effect of Cl⁻, Br⁻, NO₃⁻, SO⁼₄, H₂PO₄⁻ anions and K⁺, Na⁺, Cu²⁺, Ag⁺, Ca²⁺ cations on borate response is evaluated and it was found that only Ag⁺ had a small interference effect. The lifetime of the electrode was more than two years, when used at least 4-5 times a day, and the response time was about 20-30 s. Borate content in waste water of borax factory, tap water of a town situated near to the borax factory and city tap water far from these mines were also determined. The validation was made with differential pulse polarography for the same water sample, and high consistency was obtained.     

Surface plasmon resonance study on enhanced refractive index change of an Ag ion-sensing membrane containing dithiosquarylium dye

In this study, we have fabricated an Ag⁺ ion-sensing membrane with a dithiosquarylium (DTSQ) dye containing a polymeric film. The selective sensing signal through the electrostatic interaction between the DTSQ dye and the Ag⁺ metal cation was effectively transduced to the refractive index (RI) change corresponding to shifts of the surface plasmon resonance (SPR) angle. In addition, a good selective Ag⁺ ion detection appeared in a wide concentration range from 10⁻⁴ to 10⁻¹² M. The resonance angle shift is interpreted with Fresnel equations and Kramers-Kronig relation. In light of these calculations, the enhanced RI increase in this sensing membrane appeared to be caused by the decrease of absorption coefficient of DTSQ dye around the wavelength of SPR probe beam. These results suggest that chromogenic approaches (λ_max control of Ag⁺ ion-sensing membrane with a DTSQ dye by appropriate molecular design) related to SPR phenomena (RI change at the wavelength of probe beam) offer a good strategy for highly sensitive metal ion detection.     

Screen-printed enzyme electrodes for the detection of marker analytes during winemaking

Biosensors for malic acid and glucose have been developed, using screen-printed electrodes and two different classes of enzymes: NAD(P)⁺-dependent dehydrogenases and oxidases. The active surface of the electrodes was modified using Meldola Blue (malic acid) and Prussian Blue (glucose) and in this way sensitive, low cost and reliable NAD(P)H and H₂O₂ probes were obtained. Fixed potential amperometry was used for the detection of substrates in small volumes of sample (50 μl). Immobilization of the enzymes in a polyethylenimine-glutaraldehyde cross-linking membrane allowed sensors to be obtained with sufficient operational stability. The detection limits were of 10⁻⁵ M for malic acid and 10⁻⁶ M for glucose. The sensors were applied in the analysis of different samples of wine.     

Determination of sub-micromolar amounts of sulfide by standard free anodic stripping voltammetry and anodic stripping voltammetric titration

A novel electrochemical methods namely standard free anodic stripping voltammetry and anodic stripping voltammetric titration are proposed for determination of dissolved sulfide concentration. 2Ag⁺ + S²⁻ → Ag₂S reaction is used to provide the information. The anodic stripping voltammetric response of unreacted silver-ions at the glassy carbon electrode is used as analytical signal. Results reliability and accuracy are confirmed by analysis of model solutions, spiked natural and tap waters and recovery study, with a recovery of 100 ± 5% (n = 7) obtained. The approaches show the detection limit (3σ_blank) of 2-5 × 10⁻¹⁰ mol L⁻¹ and the relative standard deviation of 2-5% for repeated measurements.     

Characterization of home-made silver sulphide based iodide selective electrode

Polycrystalline silver sulphide/silver iodide ion selective electrodes (ISEs) with four different compositions, 9:1, 2:1, 1:1, 1:9 Ag₂S-AgI mole ratios, have been fabricated in the laboratory and characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), and electrochemical impedance spectroscopy (EIS). X-ray diffraction studies show the presence of Ag₃SI, Ag₂S and AgI crystalline phases in the electrode material. The electrode surfaces have been found to become smoother and lustrous with increasing percentage of silver sulphide in silver iodide. ISE 1:1, ISE 2:1 and ISE 9:1 all responded in Nernstian manner with slopes of about 60 mV/decade change in iodide ion concentration in the linear range of 1 × 10⁻¹ to 1 × 10⁻⁶ M while ISE 1:9 showed sub-Nernstian behavior with slope of about 45 mV up to the concentration 1 × 10⁻⁵ M. Two capacitive loops, one corresponding to the charge transfer process at metal electrode and the back contact and a second loop corresponding to the charge transfer process at membrane-electrolyte interface have been observed at high and low frequency ranges, respectively. Mott-Schottky analysis shows that the materials are n-type semiconductors with donor defect concentrations in the range of 5.1 × 10¹⁴ to 2.4 × 10¹⁹/cm³.     

A new generation of cyanide ion-selective membranes for flow injection application: part II. Comparative study of cyanide flow-injection detectors based on thin electroplated silver chalcogenide membranes

Using induced cathodic electrodeposition a number of silver chalcogenide thin layer membranes of non-trivial composition have been synthesized and their performance as ion-selective flow-injection potentiometric detectors (FIPDs) for free cyanide has been critically estimated in the context of the stringent requirements for toxic cyanide environmental monitoring. AgSCN/Ag₂S, Ag₂S, Ag_2+δSe, Ag_2+δSe_1−xTe_x (0 < δ < 0.25 and x ≈ 0.13), Ag₂Se and Ag₂Se_1−xTe_x electroplated membranes were selected for the present performance-based comparative study in order to obtain a feedback information about the effect of membrane composition. Both silver selenide and Te-doped silver selenide membranes, irrespective of their stoichiometry with respect to silver, exhibit the lowest detection limit for CN⁻ (52 ppb) with linear double-Nernstian response down to 130 ppb. The type of chalcogene anion in the membrane composition proves to exert dominant effect on the general performance characteristics of the newly developed FIPDs. The silver stoichiometry (intrinsic defects factor) and the inclusion of Te-dopant (extrinsic defects factor) have more pronounced effect on the profile of the output signal and exert moderate control on the detectors selectivity and baseline stability. This new generation of CN⁻—ion-selective membranes for FIPDs exhibits high selectivity against the common interferents present in cyanide effluents such as SCN⁻, S₂O₃²⁻, Cl⁻ and do not get poisoned in the presence of S²⁻. Moreover, their long-term stability and signal reproducibility, which make redundant the regular day-to-day calibration, coupled with the cost-effective technology for membranes preparation and easy re-generation make them attractive candidates for incorporation into automated in-field devices for in situ cyanide toxic species monitoring.     

Sulfonated poly(ether ether ketone) as an alternative charged material to poly(vinyl chloride) in the design of ion-selective electrodes

To date, poly(vinyl chloride) (PVC) is the most used polymer in the design of ion selective electrode (ISE) membranes. This paper is focused on the use of sulfonated poly(ether ether ketone) (SPEEK) as an alternative material to PVC for the design of ISEs. SPEEK of the desired degree of sulfonation is synthesized from poly(ether ether ketone) (PEEK). An NH₄⁺-ISE has been chosen as a model electrode to study the efficiency of SPEEK as polymer matrix of the membrane. The material was evaluated in ionophore free ion exchanger membranes as well as in ion-selective electrodes membranes containing nonactine as ionophore. Analytical performance parameters of the prepared electrodes were evaluated. The electrodes show a slope between 50 and 60 mV dec⁻¹ depending on both the calibration medium and the membrane composition. A linear range of response between 10⁻⁴ and 1.0 M and a lifetime of 1-2 months were obtained. The interferences of cations such us Ca²⁺, Na⁺, Li⁺ and K⁺ over the prepared ISEs are studied as well. Although the plasticizer in the SPEEK based membrane matrix is not necessary, its presence improves the sensibility. This makes SPEEK a good potential choice over alternative membrane matrices reported in the literature and a promising platform for the establishment of membrane components.     

Flow injection potentiometric determination of clobutinol hydrochloride

New clobutinol (Clob) ion-selective polyvinyl chloride (PVC) membrane electrodes, based on the ion-associates of Clob with phosphotungstic acid or phosphomolybdic acid were prepared using dibutyl phthalate as plasticizing solvent. The electrodes were characterized in terms of membrane composition, temperature and pH. The sensors showed a near-Nernstian response over the concentration ranges (6.31 × 10⁻⁶)-(1.00 × 10⁻²) and (5.01 × 10⁻⁵)-(1.00 × 10⁻²) M in the case of clobutinol-phosphotungstate ((Clob)₃-PT) applying batch and flow injection (FI) analysis, respectively, and (1.58 × 10⁻⁵)-(1.00 × 10⁻²) and (5.01 × 10⁻⁵)-(1.00 × 10⁻²) M in case of clobutinol-phosphomolybdate ((Clob)₃-PM) for batch and FI analysis systems, respectively. The electrodes were successfully applied for the potentiometric determination of ClobCl in pharmaceutical preparation and urine in steady state and flow injection conditions. The electrodes exhibit good selectivity for Clob with respect to a large number of inorganic cations, sugars and amino acids.     

A highly selective mercury electrode based on a diamine donor ligand

(H₂NCHMeCH₂NH₂)(H₂O)₂HgCl₂ (I) was synthesised, characterised and used for the fabrication of a potentiometric sensor for Hg²⁺ metal ions. Membrane having I as electroactive material, sodium tetraphenyl borate (NaTPB) as an anion excluder, dibutylamine (DBA) as plasticizer in PVC matrix in the percentage ratio of 10:3:150:150 (I:NaTPB:DBA:PVC) (w/w) exhibits a linear response to Hg²⁺ ions in a concentration range of 1.25 × 10⁻⁵ to 1.0 × 10⁻¹ M having a detection limit of 8.9 × 10⁻⁶ with a slope of 25 ± 0.1 mV over the pH range 6.6-9.3. Selectivity coefficients for Hg(II) relative to a number of interfering ions were investigated. The electrode is highly selective for Hg²⁺ ions over a large number of mono-, bi-, and trivalent cations. Normal interferents like Ag⁺ and Cd²⁺ do not interfere in the working of the electrode. The electrode has also been used successfully in mixtures having a 10% (v/v) methanol and acetone content without showing any considerable change in working concentration range or slope. These electrodes have been found to be chemically inert showing a fast response time of 10 s and were used over a period of 4 months with good reproducibility (s = ±0.2). The electrode was used for determination of mercury in binary mixtures with 100% recovery and thus the proposed sensor can be used for real sample analysis.     

Construction of novel simple phosphate screen-printed and carbon paste ion-selective electrodes

The construction and performance characteristics of different phosphate ion-selective electrodes are described. Three types of electrodes are demonstrated, namely screen-printed, carbon paste and the conventional PVC membrane electrodes. The cited electrodes are based on bisthiourea ionophores and show a considerable selectivity towards hydrogenphosphate with Nernstian slopes depending on the type of the electrode and the ionophore used. Matrix compositions of each electrode are optimised on the basis of effects of type and concentration of the ionophore as well as influence of the selected plasticizers. The screen-printed electrodes work satisfactorily in the concentration range 10⁻⁵ to 10⁻² mol L⁻¹ with anionic Nernstian compliance (32.8 mV/decade activity) and detection limit 4.0 × 10⁻⁶ mol L⁻¹. The screen-printed electrodes show fast response time of about 2.2 s and exhibit adequate shelf-life (4 months). The fabricated electrodes can be also successfully used in the potentiometric titration of HPO₄²⁻ with Ba²⁺.     

Schiff bases as cadmium(II) selective ionophores in polymeric membrane electrodes

The construction and performance characteristics of polymeric membrane electrodes based on two neutral ionophores, N,N′-[bis(pyridin-2-yl)formylidene]butane-1,4-diamine (S₁) and N-(2-pyridinylmethylene)-1,2-benzenediamine (S₂) for quantification of cadmium ions, are described. The influences of membrane compositions on the potentiometric response of the electrodes have been found to substantially improve the performance characteristics. The best performance was obtained with the electrode having a membrane composition (w/w) of (S₁) (2.15%):PVC (32.2%):o-NPOE (64.5%):KTpClPB (1.07%). The proposed electrode exhibits Nernstian response in the concentration range of 7.9 × 10⁻⁸ to 1.0 × 10⁻¹ M Cd²⁺ with limit of detection 5.0 × 10⁻⁸ M, performs satisfactorily over wide pH range (2.0-8.0) with a fast response time (10 s). The sensor has been found to work satisfactorily in partially non-aqueous media up to 30% (v/v) content of methanol, ethanol and acetonitrile and could be used for a period of 2 months. The analytical usefulness of the proposed electrode has been evaluated by its application in the determination of cadmium in real samples. The practical utility of the membrane electrode has also been observed in the presence of surfactants.     

Ultrasensitive determination of DNA sequences by flow injection chemiluminescence using silver ions as labels

We presented a new strategy for ultrasensitive detection of DNA sequences based on the novel detection probe which was labeled with Ag⁺ using metallothionein (MT) as a bridge. The assay relied on a sandwich-type DNA hybridization in which the DNA targets were first hybridized to the captured oligonucleotide probes immobilized on Fe₃O₄@Au composite magnetic nanoparticles (MNPs), and then the Ag⁺-modified detection probes were used to monitor the presence of the specific DNA targets. After being anchored on the hybrids, Ag⁺ was released down through acidic treatment and sensitively determined by a coupling flow injection–chemiluminescent reaction system (Ag⁺–Mn²⁺–K₂S₂O₈–H₃PO₄–luminol) (FI–CL). The experiment results showed that the CL intensities increased linearly with the concentrations of DNA targets in the range from 10 to 500 pmol L⁻¹ with a detection limit of 3.3 pmol L⁻¹. The high sensitivity in this work may be ascribed to the high molar ratio of Ag⁺–MT, the sensitive determination of Ag⁺ by the coupling FI–CL reaction system and the perfect magnetic separation based on Fe₃O₄@Au composite MNPs. Moreover, the proposed strategy exhibited excellent selectivity against the mismatched DNA sequences and could be applied to real samples analysis.     

Polymeric membrane electrodes with enhanced fluoride selectivity using Zr(IV)-porphyrins functioning as neutral carriers

Poly(vinyl chloride) polymeric membranes plasticized with o-NPOE (o-nitrophenyl octyl ether) or DOS (dibutyl sebacate) and containing Zr(IV)-octaethyl(OEP)- or Zr(IV)-tetraphenylporphyrins (TPP) along with lipophilic cationic additives (tridodecylmethylammonium chloride; TDMACl) are examined potentiometrically and optically with respect to their response toward fluoride. It is shown that these zirconium porphyrins can function as neutral anion carriers within the organic membranes of the electrodes. Spectrophotometric measurements of thin polymeric films indicate that the presence of lipophilic cationic sites in the form of TDMA⁺ and use of lower dielectric constant plasticizer (DOS) prevents formation of metalloporphyrin dimers in the organic polymer phase, which have been observed previously in polymeric membranes formulated with the same Zr(IV) porphyrins but with lipophilic anion site additives. By preventing dimer formation, rapid and Nernstian potentiometric response of the corresponding membrane electrodes toward fluoride ion is observed. Indeed, electrodes prepared with PVC/DOS membranes containing Zr(IV)-OEP and 15 mol% of TDMACl (relative to the ionophore) exhibit fast (t₉₅<15 s) and reversible response toward fluoride. The slope of calibration plots are near-Nernstian (−59.9 mV per decade). Such electrodes display the following selectivity pattern: ClO₄⁻>SCN⁻>F⁻>NO₃⁻>Br⁻>Cl⁻, which differs significantly from the classical Hofmeister series, with greatly enhanced potentiometric selectivity toward fluoride. The data presented herein, coupled with results from a previous study, confirm that Zr(IV) porphyrins can serve as either charged or neutral type anion carriers with respect to their enhanced interactions with fluoride when used as ionophores to prepare liquid-polymeric membrane electrodes, and that the nature of membrane additives and plasticizer dictates the response mechanism at play for given membrane formulations.     

Linear polyamines as carriers in thiocyanate-selective membrane electrodes

The polyamines, octyl-[2-(2-octylamino-ethylamino)-ethyl]-amine (L¹) and octyl-{2-[2-(2-octylamino-ethylamino)-ethylamino]-ethyl}-amine (L²), have been used as anion ionophores in PVC-based membrane ion-selective electrodes. Different electrodes were prepared containing L¹, or L², and o-nitrophenyl octyl ether (NPOE) or bis(2-ethylhexyl)sebacate (DOS) as plasticizers. The response of the electrodes was tested in two different buffers, HEPES-KOH (pH 7) and MES-KOH (pH 5.6). Electrodes containing L¹ and L² with NPOE (E1 and E2, respectively) showed a Nernstian response for thiocyanate with a good response time. The detection limit, linear range and slope for electrode E1 were 3.8 × 10⁻⁶ mol dm⁻³, 1 × 10⁻⁵ to 1 × 10⁻¹ mol dm⁻³ and −57.2 mV decade⁻¹ at pH 5.6 and 4.47 × 10⁻⁶ mol dm⁻³, 1.95 × 10⁻⁵ to 1 × 10⁻¹ mol dm⁻³ and −58.1 mV decade⁻¹ at pH 7.0. For electrode E2 the detection limit, linear range and slope found were 2.63 × 10⁻⁶ mol dm⁻³, 7.94 × 10⁻⁶ to 1 × 10⁻¹ mol dm⁻³ and −58.5 mV decade⁻¹ at pH 5.6 and 1.23 × 10⁻⁵ mol dm⁻³, 7.95 × 10⁻⁵ to 1 × 10⁻¹ mol dm⁻³ and −46.0 mV decade⁻¹ at pH 7. In contrast, electrodes containing DOS as plasticizers gave only response at pH 5.6 (detection limit, linear range and slope at pH 5.6 were 3.16 × 10⁻⁵ mol dm⁻³, 1 × 10⁻⁴ to 1 × 10⁻¹ mol dm⁻³ and −52.6 mV decade⁻¹). Selectivity coefficients for different anions with respect to thiocyanate were calculated. The electrode E2 at pH 5.6 was also used for the determination of SCN⁻ by potentiometric titrations with Ag⁺ ions with good results. The electrode E2 was also used to determine concentrations of thiocyanate in biological samples.