Optical CO(2) sensor of the combination of colorimetric change of alpha-naphtholphthalein in poly(isobutyl methacrylate) and fluorescent porphyrin in polystyrene

An optical CO₂ sensor based on the overlay of the CO₂ induced absorbance change of pH indicator dye α-naphtholphthalein in poly(isobutyl methacrylate) (polyIBM) layer with the fluorescence of tetraphenylporphyrin (TPP) in polystyrene layer is developed. The observed luminescence intensity from TPP at 655 nm increased with increasing the CO₂ concentration. The ratio I₁₀₀/I₀ value of the sensing film consisting of α-naphtholphthalein in polyIBM and TPP in polystyrene layer, where I₀ and I₁₀₀ represent the detected luminescence intensities from a layer exposed to argon and CO₂ saturated conditions, respectively, that the sensitivity of the sensor, is estimated to be 192. The response and recovery times of the sensing film are less than 6.0 s for switching from argon to CO₂, and for switching from CO₂ to argon. The signal changes are fully reversible and no hysterisis is observed during the measurements. The highly sensitive optical CO₂ sensor based on fluorescence intensity changes of TPP due to the absorption change of α-naphtholphthalein in polyIBM layer with CO₂ is achieved.     

Poly(norbornene)s as matrix materials for platinum tetrakis(pentafluorophenyl)porphyrin based optical oxygen sensors

A set of poly(norbornenes) was prepared using ring opening metathesis polymerization (ROMP) and used as matrix material for the preparation of optical oxygen sensor layers based on platinum tetrakis(pentafluorophenyl)porphyrin (PtTFPP) as the sensitive dye. Different polymers were prepared and investigated in order to retrieve information on the influence of the anchor group and the side chain attached to the polymer backbone on their performance as matrix material for the dye. Bulky side groups increased the oxygen permeability through ROM polymer layers, especially when the bulky group was directly attached via an anchor group to the polymer backbone without any aliphatic spacer in between. Sensor layers made of poly(endo,exo[2.2.1]bicyclo-5-heptene-2,3-dicarboxyclic acid di-tert-butylester) and PtTFPP exhibited the highest τ₀/τ ratio and responded strongly to small amounts of oxygen.     

Preparation of luminescent Cy5 doped core-shell SFNPs and its application as a near-infrared fluorescent marker

Cy5 dye is widely used as a biomarker in the research fields of life science because of its excitation at wavelengths above 600 nm where autofluorescence of bio-matter is much reduced. However, Cy5 dye could not be encapsulate into silica directly to form stable nanoparticles by using of the traditional methods. In this paper, an improved method had been developed to prepare Cy5 dye doped core-shell silica fluorescent nanoparticles (SFNPs), employing biomolecules conjugated Cy5 as the core material and silica coating produced from the hydrolysis TEOS (tetraethyl orthosilicate) in the water-in-oil microemulsion. To obtain stable Cy5 dye doped SFNPs with core-shell structure, five kinds of biomolecules with different iso-electric point (pI) have been selected to conjugate Cy5 for preparation of core-shell SFNPs. Results demonstrated that very bright and photostable Cy5 doped core-shell SFNPs could be both prepared by use of positive polysine conjugated Cy5 or IgG conjugated Cy5 as the core material, respectively. IgG conjugated Cy5 doped core-shell SFNPs was selected as a demonstration to be characterized and applied as a near-infrared fluorescent marker in cell recognition. The results showed that Cy5 doped core-shell SFNPs prepared by conjugating with a positive biomolecules IgG as the core material were luminescent and stable. About 110 Cy5 dye molecules could be doped in one nanoparticle with size of 42 ± 5 nm. The breast cancer cells had been selectively recognized by use of the near-infrared fluorescent marker based on the Cy5-IgG doped core-shell SFNPs. And the results demonstrated that this Cy5 doped core-shell SFNPs fluorescence marker was superior to the pure Cy5 dye marker for cell recognition in photostability and detection sensitivity.     

Optical oxygen sensor based on fluorescence change of pyrene-1-butyric acid chemisorption film on an anodic oxidation aluminium plate

An optical oxygen-sensing material based on the fluorescence intensity changes of pyrene-1-butyric acid (PBA) chemisorption film has been developed and characterised. The fluorescence intensity of PBA film decreased with increase of oxygen concentration. The I₀/I₁₀₀ value of PBA film is estimated to be 6.14±0.15 and large Stern-Volmer constant (K_SV=0.028±0.13 Torr⁻¹) is obtained. After irradiation for 24 h with 150 W tungsten lamp, little changes of oxygen-sensing properties were observed. These results indicate that PBA film is highly oxygen-sensitive and photostability device. The response times of the PBA chemisorption film were 10.0 s for switching from argon to oxygen, and 53.0 s for switching from oxygen to argon. Moreover, the optical sensor based on the PBA chemisorption film was applied to the measurement of oxygen concentration in aqueous solution.     

Novel optical oxygen sensing material: metalloporphyrin dispersed in fluorinated poly(aryl ether ketone) films

A series of new fluorine-containing poly(aryl ether ketone)s (8F-PEKEK(Ar); Ar: 2-2-bis(4-hydroxyphenyl)-1,1,1,3,3,3-hexafluoropropane (6FBA), 2,2-bis(4-hydroxyphenyl)propane (BA), 2-(4-hydroxyphenyl)-2-(3-hydroxyphenyl)propane (3,4^′-BA) or 9,9^′-bis(4-hydroxyphenyl)fluorine (HF)) are synthesized and applied to the matrix of optical oxygen sensing using phosphorescence quenching of metalloporphyrins, platinum and palladium octaethylporphyrin, (PtOEP and PdOEP) by oxygen. The phosphorescence intensity of PtOEP and PdOEP in 8F-PEKEK(Ar) films decreased with increase of oxygen concentration. The ratio I₀/I₁₀₀ is used as a sensitivity of the sensing film, where I₀ and I₁₀₀ represent the detected phosphorescence intensities from a film exposed to 100% argon and 100% oxygen, respectively. For PtOEP in 8F-PEKEK(Ar) film, I₀/I₁₀₀ values are more than 20.0 and large Stern-Volmer constants more than 0.19%⁻¹ are obtained compared with PtOEP in polystyrene film. For PdOEP in 8F-PEKEK(Ar) film, on the other hand, the large I₀/I₁₀₀ values more than 143 are obtained. However, the Stern-Volmer plots of PdOEP in 8F-PEKEK(Ar) films exhibit considerable linearity at lower oxygen concentration range between 0% and 20%. These results indicate that PtOEP and PdOEP films are useful optical oxygen sensor at the oxygen concentration range between 0% and 100% and between 0% and 20%, respectively. The response times of PtOEP and PdOEP dispersed in 8F-PEKEK(Ar) films are 5.6 and 3.0 s on going from argon to oxygen and 110.1 and 160.0 s from oxygen to argon, respectively.     

Optimising oxygen-sensitivity of optical sensor using pyrene carboxylic acid by myristic acid co-chemisorption onto anodic oxidized aluminium plate

Optical oxygen-sensitivity using pyrene carboxylic acid with long alkyl chain (1-pyrenedecanoic acid and 1-pyrenedodecanoic acid) and myristic acid co-chemisorption layer was controlled by varying the molar ratio of myristic acid to pyrene carboxylic acid. The ratio I₀/I₁₀₀, where I₀ and I₁₀₀ represent the detected fluorescence intensities from a substrate exposed to 100% argon and 100% oxygen, respectively, is used as an indicator of the sensitivity of the sensing film. At a composition ratio of 1 pyrene carboxylic acid to 10 myristic acids, the I₀/I₁₀₀ attained its maximum value and then the ratio decreased with increase in the molar ratio of myristic acid to pyrene carboxylic acid. The Stern-Volmer constant (K_SV) also attained its maximum value at a composition ratio of one pyrene carboxylic acid to ten myristic acids and then the ratio decreased with increase in the molar ratio of myristic acid to pyrene carboxylic acid. The oxygen-sensitivity of optical sensor using pyrene carboxylic acid is optimized by myristic acid co-chemisorption.     

A fiber-optic evanescent wave sensor for dissolved oxygen detection based on novel hybrid fluorinated xerogels immobilized with [Ru(bpy)3]2+

We have prepared a novel fiber-optic evanescent wave sensor (FEWS) for dissolved oxygen (DO) detection. The sensor fabrication was based on coating a decladded portion of an optical fiber with a microporous coating, which was prepared from 3,3,3-trifluoropropyltrimethoxysilane and n-propyltrimethoxysilane. The fluorophores were immobilized in the porous coating and excited by the evanescent wave field produced on the core surface of the optical fiber. The sensitivity of the sensor was quantified by the ratio of the fluorescence intensities in pure deoxygenated (I ₀) and in pure oxygenated environments (I). Results show that the quenching response of DO is increased with the enhancement of the coating surface hydrophobicity using the presented hybrid fluorinated ORMOSILs. The calibration curve of I ₀/I to [O₂] is linear from 0 to 40 ppm and the detection limit is 0.05 ppm (3σ) with a short response time of 15 s for DO detection. Figure       

Optical fiber evanescent wave absorption spectrometry of nanocrystalline tin oxide thin films for selective hydrogen sensing in high temperature gas samples

SnO₂ nanocrystalline material was prepared with a sol-gel process and thin films of the nanocrystalline SnO₂ were coated on the surface of bent optical fiber cores for gas sensing. The UV/vis absorption spectrometry of the porous SnO₂ coating on the surface of the bent optical fiber core exposed to reducing gases was investigated with a fiber optical spectrometric method. The SnO₂ film causes optical absorption signal in UV region with peak absorption wavelength at around 320 nm when contacting H₂-N₂ samples at high temperatures. This SnO₂ thin film does not respond to other reducing gases, such as CO, CH₄ and other hydrocarbons, at high temperatures within the tested temperature range from 300 °C to 800 °C. The response of the sensing probe is fast (within seconds). Replenishing of the oxygen in tin oxide was demonstrated by switching the gas flow from H₂-N₂ mixture to pure nitrogen and compressed air. It takes about 20 min for the absorption signal to decrease to the baseline after the gas sample was switched to pure nitrogen, while the absorption signal decreased quickly (in 5 min) to the baseline after switching to compressed air. The adhesion of tin oxide thin films is found to be improved by pre-coating a thin layer of silica gel on the optical fiber. Adhesion increases due to increase interaction of optical fiber surface and the coated silica gel and tin oxide film. Optical absorption spectra of SnO₂ coating doped with 5 wt% MoO₃ were observed to change and red-shifted from 320 nm to 600 nm. SnO₂ thin film promoted with 1 wt% Pt was found to be sensitive to CH₄ containing gas.     

Extended detection range for an optical enzymatic glucose sensor coupling with a novel data-processing method

A new data-processing method was established and applied for optical enzymatic glucose sensing, in which oxygen and glucose were simultaneously consumed. The oxygen level remaining in the detection system, which was equal to the difference between the initial and consumed oxygen concentrations, could be measured using fluorescent oxygen indicators immobilized in the sensing layer. It was deduced that the ratio of I ₀ and I was inversely proportional to glucose concentration, where I ₀ is the maximum fluorescence intensity in various glucose solutions, and I is the fluorescence intensity at various concentrations of glucose. Using the new data-processing method, the detection range of the calibration curve method was extended from 0 to 1.2 mmol L^?1, which was enlarged about 2–3 folds over that in ordinary approaches. The prepared glucose sensor could be directly applied to detect high concentrations of glucose.     

Optical sensor for carbon dioxide combining colorimetric change of a pH indicator and a reference luminescent dye

A new optical CO₂ sensor based on the luminescence intensity change of the europium(III) complex tris(thenoyltrifluoroacetonato) europium(III) dihydrate ([Eu(tta)₃]) caused by the absorption change of various pH indicators—thymol blue, phenol red, or cresol red—with CO₂ was developed and its CO₂ sensing properties were investigated. For all the CO₂ sensors using pH indicators the observed luminescence intensity from [Eu(tta)₃] at 613 nm increased with increasing CO₂ concentration. The linear calibration method based on the plot of (I₁₀₀–I₀)/(I–I₀) versus the inverse of CO₂ concentration was suggested, where I₀ and I₁₀₀ were luminescence intensities at 613 nm of the CO₂ sensor film in 100% nitrogen and 100% gaseous CO₂. In all cases the plots showed good linearity and the correlation factors of the plots, r², were 0.991 for thymol blue, 0.990 for phenol red, and 0.998 for cresol red. The slopes of the plots (A/B) for thymol blue, phenol red, and cresol red were 2.2, 5.2, and 9.0%, respectively. The response times of the CO₂ sensor film were 4.0 s for thymol blue, 4.4 s for phenol red, and 8.8 s for cresol red for switching from nitrogen to CO₂, and the recovery times of films were 36 s for thymol blue, 39.2 s for phenol red, and 56.6 s for cresol red for switching from CO₂ to nitrogen. The signal changes were fully reversible and hysteresis was not observed during the measurements. The highly sensitive CO₂ sensor was developed using thymol blue as an indicator for the CO₂-sensing probe.     

A fluorescence ratiometric sensor for hypochlorite based on a novel dual-fluorophore response approach

A fluorescence ratiometric sensor for OCl⁻ has been developed based on a novel dual fluorophore response approach. The sensor molecule contains a coumarin fluorophore and a rhodamine fluorophore, and the two fluorophores are directly linked to an OCl⁻ recognition group. The structure of the sensor was characterized by ESI-MS, NMR, and X-ray crystallographic analysis. Upon treatment with OCl⁻, both fluorophores in the sensor responded simultaneously at two separate optical windows, with large enhancement of the fluorescence ratio (I₅₇₈/I₅₀₁) from 0.01 to 39.55. The fluorescence ratios for the sensor showed a good linearity with the concentration of OCl⁻ in the range of 0.2–40 μM and the detection limits is 0.024 μM (S N⁻¹ = 3). Investigation of reaction products indicated that the sensor reaction with OCl⁻ produced two new fluorescent molecules, which were responsible for the fluorescence changes in two optical windows. In addition, the sensor showed high selectivity to OCl⁻ over other reactive oxygen species, reactive nitrogen species, cations, and anions. The sensor has also been successfully applied to detection of OCl⁻ in natural water samples with satisfactory recovery.     

A new class of silica cross-linked micellar core-shell nanoparticles

Micellar nanoparticles made of surfactants and polymers have attracted wide attention in the materials and biomedical community for controlled drug delivery, molecular imaging, and sensing; however, their long-term stability remains a topic of intense study. Here we report a new class of robust, ultrafine silica core-shell nanoparticles formed from silica cross-linked, individual block copolymer micelles. Compared with pure polymeric micelles, the main advantage of the new core-shell nanoparticles is that they have significantly improved stability and do not break down during dilution. We also studied the drug loading and release properties of the silica cross-linked micellar particles, and we found that the new core-shell nanoparticles have a slower release rate which allows the entrapped molecules to be slowly released over a much longer period of time under the same experimental conditions. A range of functional groups can be easily incorporated through co-condensation with the silica matrix. The potential to deliver hydrophobic agents into cancer cells has been demonstrated. Because of their unique structures and properties, these novel core-shell nanoparticles could potentially provide a new nanomedicine platform for imaging, detection, and treatment, as well as novel colloidal particles and building blocks for mutlifunctional materials.     

Lifetime-based optical sensor for high-level pCO2 detection employing fluorescence resonance energy transfer

An optical sensor for the measurement of high levels of carbon dioxide in gas phase has been developed. It is based on fluorescence resonance energy transfer (FRET) between a long-lifetime ruthenium polypyridyl complex and the pH-active disazo dye Sudan III. The donor luminophore and the acceptor dye are both immobilised in a hydrophobic silica sol–gel/ethyl cellulose hybrid matrix material. Tetraoctylammonium hydroxide (TOA-OH) is used as an internal buffering system. Fluorescence lifetime is measured in the frequency domain, using low-cost phase modulation measurement technology. The use of Sudan III as an acceptor dye has enabled the sensor to have a dynamic range up to 100% carbon dioxide. The sensor displays 11.2° phase shift between the limit of detection (LOD) of 0.06 and 100% CO₂ with a resolution of better than 2%. The encapsulation in the silica/polymer hybrid material has provided the sensor with good mechanical and chemical stability. The effect of molecular oxygen, humidity and temperature on the sensor performance was studied in detail.     

Electrochemiluminescence immunosensor for ultrasensitive detection of biomarker using Ru(bpy)3-encapsulated silica nanosphere labels

Here, we describe a new approach for electrochemiluminescence (ECL) assay with Ru(bpy)₃²⁺-encapsulated silica nanoparticle (SiO₂@Ru) as labels. A water-in-oil (W/O) microemulsion method was employed for one-pot synthesis of SiO₂@Ru nanoparticles. The as-synthesized SiO₂@Ru nanoparticles have a narrow size distribution, which allows reproducible loading of Ru(bpy)₃²⁺ inside the silica shell and of α-fetoprotein antibody (anti-AFP), a model antibody, on the silica surface with glutaraldehyde as linkage. The silica shell effectively prevents leakage of Ru(bpy)₃²⁺ into the aqueous solution due to strong electrostatic interaction between the positively charged Ru(bpy)₃²⁺ and the negatively charged surface of silica. The porous structure of silica shell allowed the ion to move easily through the pore to exchange energy/electrons with the entrapped Ru(bpy)₃²⁺. The as-synthesized SiO₂@Ru can be used as a label for ultrasensitive detection of biomarkers through a sandwiched immunoassay process. The calibration range of AFP concentration was 0.05-30 ng mL⁻¹ with linear relation from 0.05 to 20 ng mL⁻¹ and a detection limit of 0.035 ng mL⁻¹ at 3σ. The resulting immunosensors possess high sensitivity and good analytical performance.     

Study of migration of active components of phosphorescent oxygen sensors for food packaging applications

A study of migration of the active components of oxygen sensors into food is presented. Six types of sensors, based on different oxygen sensitive dyes (two metalloporphyrins and one ruthenium dye), polymers (polystyrene and polysulfone) and support materials, were exposed to a number of standard ‘food simulants’ recommended by FDA/EU guidelines and then assayed for migration or sensor components and changes in oxygen calibration. Both metalloporphyrin sensor dyes leached only in olive oil and in 95% ethanol (used as a positive control), at maximum levels of 19.22 μg/dm² for PtOEPK and 113.96 μg/dm² for PtTFPP. The RuDPP dye showed maximum leaching in 95% ethanol (25.19 μg/dm²) while also migrating in an acidic aqueous simulant. Planar supports such as polyester tended to enhance the stability of the sensor. Migration of the styrene monomer from the polystyrene encapsulation medium was concluded to be low enough to be insignificant. Migration of sensor components was shown to correlate with the changes in sensor response to oxygen. Based on these results, sensor combinations were ranked on the basis of their resistance to leaching and their general stability, safety and suitability for use on a large scale in packaged foods and related food applications was proven.     

A fluorescence ratiometric nano-pH sensor based on dual-fluorophore-doped silica nanoparticles

We have synthesized dual-fluorophore-doped core-shell silica nanoparticles used as ratiometric pH sensor. The nanoparticles were prepared with a reverse microemulsion technique by simultaneously encapsulating two different fluorophores, the pH-sensitive dye fluorescein as a pH indicator and the pH-insensitive dye phenosafranine as an internal reference for fluorescence ratiometric measurement, into silica shell. The nanoparticles prevent the fluorescence dyes leaching from the silica matrix when immersed inside water. The hydrophilic silica shells were made by hydrolysing and polymerizing tetraethoxysilane (TEOS) in water-in-oil microemulsion. The fluorescence intensity ratio of the two dyes varied linearly as a function of pH in the range from 4.0 to 8.0. The sensor was also applied to measure pH of real water samples. The results are in good agreements with that using the conventional glass electrode method. The as-prepared fluorescent nanoparticles showed rapid response, excellent stability and high reproducibility as pH sensors.     

单分散、规则球形Au@SiO2核-壳纳米粒的制备及光谱研究

采用3-巯基丙基三甲氧基硅烷作为联结剂,成功将单个金纳米粒子包在氧化硅壳中,制得Au@SiO₂核壳纳米粒子;该复合纳米粒子形貌呈球形、单分散性较好,金纳米粒子位于氧化硅球的中心,无团聚的金纳米粒子包覆在氧化硅壳中。采用透射电镜(TEM)对样品的形貌进行了表征,通过能量散射X-射线能谱(EDX)分析了目标物的化学成分,并对所得核壳纳米粒子的光谱性质进行了研究。     

Highly sensitive colorimetric detection of NH3 based on Au@Ag@AgCl core-shell nanoparticles

As an important component of the atmosphere, ammonia (NH₃) plays a very important role in maintaining the balance of environment. However, it is also one of the most toxic gases that can cause damage to the human respiratory system and mucous membranes even at low concentrations. As such, development of highly sensitive and selective NH₃ sensors is of high significance for environmental monitoring and health maintenance. Herein, we have synthesized Au@Ag@AgCl core-shell nanoparticles (NPs) by oxidative etching and precipitating Au@Ag core-shell NPs using FeCl₃ and further used them as optical probes for the colorimetric detection of NH₃. The sensing mechanism is based on the fact that the etching of NH₃ on AgCl and Ag shell leads to the variations of ingredients and core-to-shell ratio of the Au@Ag@AgCl NPs, thereby inducing noticeable spectral and color changes. By replacing the outmost layer of Ag with AgCl, not only is the stability of the sensor against oxygen significantly enhanced, but also is the sensitivity of the method improved. The method exhibits good linear relationship for the detection of NH₃ from 0 to 5000 μmol/L with the limit of detection of 6.4 μmol/L. This method was successfully applied to the detection of simulated air polluted by NH₃, indicating its practical applicability for environmental monitoring. This method shows great potential for on-site NH₃ detection particularly in remote area, where a simple, fast, low-cost, and easy-to-handle method is highly desirable.     

A composite thin film optical sensor for dissolved oxygen in contaminated aqueous environments

A robust optical composite thin film dissolved oxygen sensor was fabricated by ionically trapping the dye ruthenium(II) tris(4,7-diphenyl-1,10-phenanthroline) dichloride in a blended fluoropolymer matrix consisting of Nafion^® and Aflas^®. Strong phosphorescence, which was strongly quenched by dissolved oxygen (DO), was observed when the sensor was immersed in water. The sensor was robust, optically transparent, with good mechanical properties. Fast response, of a few seconds, coupled with sensitivity of about 0.1 mg L⁻¹ (DO) over the range 0-30 mg L⁻¹ and resistance to leaching, were also exhibited by this system. The Stern-Volmer (SV) plot exhibited slight downward turning at all oxygen concentrations. A linear plot was obtained when the SV equation was modified to account for the varying sensitivity of dye molecules in the matrix to the quencher. Good long term stability was observed.     

γ-Ray induced catalytic properties of the silica nanoparticles dispersed in the aerated aqueous solution

Silica nanoparticles (NPs) dispersed in an aerated aqueous solution containing Ag⁺ were irradiated to a dose of 10 kGy using ⁶⁰Co γ-rays. The typical surface plasmon band of Ag NPs was observed around 400 nm, indicating that even in the presence of dissolved oxygen the reduction of Ag⁺ occurred by silica NPs. Transmission electron microscopy images indicated that Ag NPs formed on the surface of the silica NPs. The subtraction spectra showed broad absorption around 500 nm with the absorbance depending on the dose. The electrons generated by charge separation from silica NPs with a size of about 12 nm reduce Ag⁺ to Ag⁰ and form (Ag⁰) _n species on the silica NPs, and the type of (Ag⁰) _n species formed depended on the silica NP, and Ag⁺ contents, and the dose. In the co-presence of organic molecules on the silica NP such as rhodamine, the absorbance of the surface plasmon band of both Ag NPs and rhodamine decreased, indicating the electrons to participate in the reductive decomposition of rhodamine molecules adsorbed on the silica NP. Furthermore, in the case when the silica NPs contained fluorescein molecules, the fluorescein molecules were also decomposed, indicating that the fluorescein molecules adsorbed on the inner surface of the silica NPs. The addition of I₂ as an oxidative reagent prevented the decomposition of the fluorescein molecules, indicating that electrons are the main species emitted from irradiated silica NPs.