Analytical methodology for sampling and analysing eight siloxanes and trimethylsilanol in biogas from different wastewater treatment plants in Europe

Siloxanes and trimethylsilanol belong to a family of organic silicone compounds that are currently used extensively in industry. Those that are prone to volatilisation become minor compounds in biogas adversely affecting energetic applications. However, non-standard analytical methodologies are available to analyse biogas-based gaseous matrixes. To this end, different sampling techniques (adsorbent tubes, impingers and tedlar bags) were compared using two different configurations: sampling directly from the biogas source or from a 200 L tedlar bag filled with biogas and homogenised. No significant differences were apparent between the two sampling configurations. The adsorbent tubes performed better than the tedlar bags and impingers, particularly for quantifying low concentrations. A method for the speciation of silicon compounds in biogas was developed using gas chromatography coupled with mass spectrometry working in dual scan/single ion monitoring mode. The optimised conditions could separate and quantify eight siloxane compounds (L₂, L₃, L₄, L₅, D₃, D₄, D₅ and D₆) and trimethylsilanol within fourteen minutes. Biogas from five waste water treatment plants located in Spain, France and England was sampled and analysed using the developed methodology. The siloxane concentrations in the biogas samples were influenced by the anaerobic digestion temperature, as well as the nature and composition of the sewage inlet. Siloxanes D₄ and D₅ were the most abundant, ranging in concentration from 1.5 to 10.1 and 10.8 to 124.0 mg Nm⁻³, respectively, and exceeding the tolerance limit of most energy conversion systems.     

Improvement of the analysis of the biochemical oxygen demand (BOD) of Mediterranean seawater by seeding control

Biochemical oxygen demand (BOD) is a useful parameter for assessing the biodegradability of dissolved organic matter in water. At the same time, this parameter is used to evaluate the efficiency with which certain processes remove biodegradable natural organic matter (NOM). However, the values of BOD in seawater are very low (around 2 mg O₂ L⁻¹) and the methods used for its analysis are poorly developed. The increasing attention given to seawater desalination in the Mediterranean environment, and related phenomena such as reverse osmosis membrane biofouling, have stimulated interest in seawater BOD close to the Spanish coast. In this study the BOD analysis protocol was refined by introduction of a new step in which a critical quantity of autochthonous microorganisms, measured as adenosine triphosphate, is added. For the samples analyzed, this improvement allowed us to obtain reliable and replicable BOD measurements, standardized with solutions of glucose-glutamic acid and acetate. After 7 days of analysis duration, more than 80% of ultimate BOD is achieved, which in the case of easily biodegradable compounds represents nearly a 60% of the theoretical oxygen demand. BOD₇ obtained from the Mediterranean Sea found to be 2.0 ± 0.3 mg O₂ L⁻¹ but this value decreased with seawater storage time due to the rapid consumption of labile compounds. No significant differences were found between two samples points located on the Spanish coast, since their organic matter content was similar. Finally, the determination of seawater BOD without the use of inoculum may lead to an underestimation of BOD.     

An experimental approach for the development of direct-absorption sampling method for determination of trimethylsilanol and volatile methylsiloxanes by the GC-MS technique in landfill gas

This paper reports on an absorption method used for the determination of six target volatile methylsiloxanes and trimethylsilanol existing in raw biogas samples by means of a special and portable sampling train system. After biogas sampling (no accurate pump needed), the samples obtained were analysed by gas chromatography-mass spectrometry (GC-MS). The optimisation of the used solvent was carried out, and acetone was selected as the preferred liquid medium for trapping the siloxanes. The results clearly showed that using pure acetone and a mixture of acetone and water (97/3% = v/v) ensures very good solvation of silicon-contained molecules; thus the sampling procedure was more accurate. Replicate samples showed that the relative standard deviation of the method was less than 5.7% and 6.3% for methylsiloxanes as well as less than 2.1% and 2.4% for trimethylsilanol analysed 24 and 72 hours after sampling, respectively. Furthermore, limits of detection were determined theoretically and experimentally. The limits of detection for siloxanes and trimethylsilanol were in the range 0.04–0.11 mg/Nm³ and 0.08–0.12 mg/Nm³, respectively. The limit of quantification for trimethylsilanol was 0.1 mg/Nm³, whereas the limit for siloxanes ranged from 0.1 to 0.13 mg/Nm³. Finally, raw biogas samples were successfully analysed by the developed method. Trimethylsilanol and methylsiloxanes were found in the concentrations of 34.5 mg/Nm³ and 1.7–20 mg/Nm³ in the analysed raw biogas, respectively.     

Theoretical study of the thermochemistry and the kinetics of the SFxCl (x = 0-5) series

A systematic thermodynamic and kinetic study of the entire SF_xCl (x = 0-5) series has been carried out. High-level quantum chemical composite methods have been employed to derive enthalpy of formation values from calculated atomization and isodesmic energies. The resulting values for the SCl, SFCl, SF₂Cl(C₁), SF₃Cl(C_s), SF₄Cl(C_s) and SF₅Cl molecules are 28.0, −36.0, −64.2, −134.3, −158.2 and −237.1 kcal mol⁻¹. A comparison with previous experimental and theoretical values is presented. Statistical adiabatic channel model/classical trajectory, SACM/CT, calculations of selected complex-forming and recombination reactions of F and Cl atoms with radicals of the series have been performed between 200 and 500 K. The reported rate coefficients span over the normal range of about 6 × 10⁻¹² and 5 × 10⁻¹¹ cm³ molecule⁻¹ s⁻¹ expected for this type of barrierless reactions.     

Significant fluorescence enhancement by supramolecular complex formation between berberine chloride and cucurbit(n=7)uril and its analytical application

The supramolecular interaction of cucurbit(n = 7)uril (Q[7]) with berberine chloride (BER) has been studied in aqueous solution at pH 2.0 and room temperature by spectro-fluorimetry. The association constant of the complex was 2.07 × 10⁶ L mol⁻¹ calculated by using a nonlinear least squares method. ¹H NMR spectra confirmed that a 1:1 stable complex is formed between Q[7] and BER. This work proposes a possible interaction mode, in which the guest BER is incorporated inside the hydrophobic cavity of the host Q[7] via the isoquinoline ring part of the guest molecule. Based on a significant enhancement of the fluorescence intensity of this supramolecular complex, a spectrofluorimetric method with high sensitivity and selectivity has been developed for the determination of BER in aqueous solution in the presence of Q[7]. The linear range of the method was from 7.43 to 11.2 × 10³ ng mL⁻¹with the detection limit 4.2 ng mL⁻¹. There was no interference from the compounds normally used in tablets, serum or urine constituents. The proposed method was applied to the determination of BER in tablets, serum and urine samples with satisfactory results and good consistency with those obtained by the pharmacopoeia method. This shows that it has promising potential for therapeutic drug monitoring and pharmokinetics and for clinical application.     

Siloxanes in Biogas: Approaches of Sampling Procedure and GC-MS Method Determination

A new approach of siloxane sampling based on impinger, micro-impinger, adsorption on active carbon, and direct TedlarBag methods followed by gas chromatography-mass spectrometry (GC-MS) was developed for the analysis of three linear (L2–L4) and four cyclic (D3–D5) volatile methyl siloxanes (VMSs). Three kinds of organic liquid-medium characterized by different polarities, namely acetone, methanol, and d-decane as siloxanes trap were arranged in the experiment which is widely discussed below. Thus, the GC-MS equipped with SUPELCOWAX-10 capillary column was employed to perform monitoring of VMS content in the analyzed biogas samples originating from landfill, wastewater treatment plants, and agriculture biogas plants. In all samples that have undergone the analysis, cyclic and linear VMSs were found in quantities exceeding 107.9 and 3.8 mg/m³, respectively. Significant differences between siloxanes concentrations depending on biogas origin were observed. Moreover, the high range of linearity (0.1 to 70.06 mg/m³), low LoD (0.01 mg/m³), low LoQ (0.04 mg/m³), and high recovery (244.1%) indicate that the procedure and can be applied in sensitive analyses of silica biogas contaminants. In addition to the above, the impinger method of sampling performed better than active-carbon Tube and TedlarBag, particularly for quantifying low concentrations of siloxanes. Overall, the evaluation of sampling methods for biogas collection simplified the analytical procedure by reducing the procedural steps, avoiding the use of solvents, as well as demonstrated its applicability for the testing of biogas quality.     

Quantum chemistry studies on the Ru-M interactions and the P NMR in [Ru(CO)3(Ph2Ppy)2(MCl2)] (M = Zn, Cd, Hg)

To study the Ru-M interactions and their effects on ³¹P NMR, complexes [Ru(CO)₃(Ph₂Ppy)₂] (py = pyridine) (1) and [Ru(CO)₃(Ph₂Ppy)₂MCl₂] (M = Zn, 2; Cd, 3; Hg, 4) were calculated by density functional theory (DFT) PBE0 method. Moreover, the PBE0-GIAO method was employed to calculate the ³¹P chemical shifts in complexes. The calculated ³¹P chemical shifts in 1-3 follow 2 > 3 > 1 which are consistent to experimental results, proving that PBE0-GIAO method adopted in this study is reasonable. This method is employed to predict the ³¹P chemical shift in designed complex 4. Compared with 1, the ³¹P chemical shifts in 2-4 vary resulting from adjacent Ru-M interactions. The Ru → M or Ru ← M charge-transfer interactions in 2-4 are revealed by second-order perturbation theory. The strength order of Ru → M interactions is the same as that of the P-Ru → M delocalization with Zn > Cd > Hg, which coincides with the order of ³¹P NMR chemical shifts. The interaction of Ru → M, corresponding to the delocalization from 4d orbital of Ru to s valence orbital of M²⁺, results in the delocalization of P-Ru → M, which decreases the electron density of P nucleus and causes the downfield ³¹P chemical shifts. Except 2, the back-donation effect of Ru ← M, arising from the delocalization from s valence orbital of M²⁺ to the valence orbital of Ru, is against the P-Ru → M delocalization and results in the upfield ³¹P chemical shifts in 4. Meanwhile, the binding energies indicate that complex 4 is stable and can be synthesized experimentally. However, as complex [Ru(CO)₃(Ph₂Ppy)₂HgCl]⁺5 is more stable than 4, the reaction of 1 with HgCl₂ only gave 5 experimentally.     

Comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry combined with solid phase microextraction as a powerful tool for quantification of ethyl carbamate in fortified wines. The case study of Madeira wine

An analytical methodology based on headspace solid phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography—time-of-flight mass spectrometry (GC × GC–ToFMS) was developed for the identification and quantification of the toxic contaminant ethyl carbamate (EC) directly in fortified wines. The method performance was assessed for dry/medium dry and sweet/medium sweet model wines, and for quantification purposes, calibration plots were performed for both matrices using the ion extraction chromatography (IEC) mode (m/z 62). Good linearity was obtained with a regression coefficient (r²) higher than 0.981. A good precision was attained (R.S.D. <20%) and low detection limits (LOD) were achieved for dry (4.31 μg/L) and sweet (2.75 μg/L) model wines. The quantification limits (LOQ) and recovery for dry wines were 14.38 μg/L and 88.6%, whereas for sweet wines were 9.16 μg/L and 99.4%, respectively. The higher performance was attainted with sweet model wine, as increasing of glucose content improves the volatile compound in headspace, and a better linearity, recovery and precision were achieved. The analytical methodology was applied to analyse 20 fortified Madeira wines including different types of wine (dry, medium dry, sweet, and medium sweet) obtained from several harvests in Madeira Island (Portugal). The EC levels ranged from 54.1 μg/L (medium dry) to 162.5 μg/L (medium sweet).     

Theoretical insight into stereodynamics of the O(D) + H2 (v = 0–3, j = 0) → OH + H reaction: A quasiclassical trajectory (QCT) study

In this work, the reaction O(¹D) + H₂ → OH + H has been theoretically studied using the quasiclassical trajectory (QCT) method developed by Han and co-workers. All the quasiclassical trajectory calculations are performed on the DK (Dobbyn and Knowles) potential energy surface (PES). The vector correlation information on the reaction O(¹D) + H₂ → OH + H has been obtained. It has been demonstrated that the product alignment is sensitive to the reactant vibrational quantum number (v) at collision energy of 19 kcal/mol. Moreover, with increasing the value of v, backward scattering becomes weaker and forward scattering becomes stronger.     

A new generation of cyanide ion-selective membranes for flow injection application: part II. Comparative study of cyanide flow-injection detectors based on thin electroplated silver chalcogenide membranes

Using induced cathodic electrodeposition a number of silver chalcogenide thin layer membranes of non-trivial composition have been synthesized and their performance as ion-selective flow-injection potentiometric detectors (FIPDs) for free cyanide has been critically estimated in the context of the stringent requirements for toxic cyanide environmental monitoring. AgSCN/Ag₂S, Ag₂S, Ag_2+δSe, Ag_2+δSe_1−xTe_x (0 < δ < 0.25 and x ≈ 0.13), Ag₂Se and Ag₂Se_1−xTe_x electroplated membranes were selected for the present performance-based comparative study in order to obtain a feedback information about the effect of membrane composition. Both silver selenide and Te-doped silver selenide membranes, irrespective of their stoichiometry with respect to silver, exhibit the lowest detection limit for CN⁻ (52 ppb) with linear double-Nernstian response down to 130 ppb. The type of chalcogene anion in the membrane composition proves to exert dominant effect on the general performance characteristics of the newly developed FIPDs. The silver stoichiometry (intrinsic defects factor) and the inclusion of Te-dopant (extrinsic defects factor) have more pronounced effect on the profile of the output signal and exert moderate control on the detectors selectivity and baseline stability. This new generation of CN⁻—ion-selective membranes for FIPDs exhibits high selectivity against the common interferents present in cyanide effluents such as SCN⁻, S₂O₃²⁻, Cl⁻ and do not get poisoned in the presence of S²⁻. Moreover, their long-term stability and signal reproducibility, which make redundant the regular day-to-day calibration, coupled with the cost-effective technology for membranes preparation and easy re-generation make them attractive candidates for incorporation into automated in-field devices for in situ cyanide toxic species monitoring.     

Design of single chain magnets through cyanide-bearing six-coordinate complexes

The design and preparation of stable cyanide-bearing six-coordinate complexes of formula [M^III(L)(CN)_x]^{(x + l − m)−} (M = trivalent transition metal ion and L = polydentate blocking ligand) are summarized here. Their use as ligands towards either fully hydrated metal ions or coordinatively unsaturated preformed species, to afford a wide variety of low-dimensional metal assemblies whose nuclearity, dimensionality and magnetic properties can be tuned, is also reviewed. Special emphasis is put on the appropriate choice of the end-cap ligand L whose denticity determines the number of coordinated cyanide groups in the mononuclear precursors. Among the different new spin topologies obtained through this rational synthetic strategy, ferromagnetically coupled 4,2-ribbon like bimetallic chains which exhibit slow magnetic relaxation and hysteresis effects (chain as magnets) are one of the most appealing and constitute the heart of the present contribution.     

Theoretical investigation on H2 elimination reactions of germylenoid H2GeLiF with RH (R = F, OH, and NH2)

The H₂ elimination reactions of the germylenoid H₂GeLiF with RH (R = F, OH, NH₂) have been studied by using the DFT B3LYP and QCISD methods. The calculated results indicate that all the mechanisms of the three reactions are identical to each other and under the same condition the H₂ elimination reactions should occur easily in the order of H-F > H-OH > H-NH₂. In THF solvent the H₂ elimination reactions get more difficult than in gas phase. Compared with the insertion reactions of H₂GeLiF with RH (R = F, OH, NH₂), the H₂ elimination reactions have the lower activation barriers and should be more favorable.     

Vibrational spectra and structural parameters of some XNCO and XOCN (X = H, F, Cl, Br) molecules

Ab initio calculations with full electron correlation by the perturbation method to second order and hybrid density functional theory calculations by the B3LYP method utilizing the 6-31G(d), 6-311+G(d, p), and 6-311+G(2d, 2p) basis sets have been carried out for the XNCO and XOCN (X = H, F, Cl, Br) molecules. From these calculations, force constants, vibrational frequencies, infrared intensities, Raman activities, depolarization ratios, and structural parameters have been determined and compared to the experimental quantities when available. By combining previously reported rotational constants for HNCO, ClNCO and BrNCO with the ab initio MP2/6-311+G(d, p) predicted structural values, adjusted r₀ parameters have been obtained. The r₀ values for BrNCO are: r(BrN) = 1.857(5); r(NC) = 1.228(5); r(CO) = 1.161(5) Å; BrNC = 117.5(5) and NCO = 172.3(5)°. For ClNCO the determined r₀ parameters are in excellent agreement with the previously determine r_s values, whereas those for HNCO the HNC angle is larger with a value of 126.3(5)° compared to the previous reported value of 123.9(17)°. However, considering the relatively large uncertainty in the value given initially the two results are in near agreement. Structural parameters are also estimated for FNCO and XOCN (X = H, F, Cl, Br). The centrifugal distortion constants have been calculated and are compared to the experimentally (XNCO: X = H, Cl, Br) determined values. Predicted values for the barriers of linearity are given for both the XNCO (X = H, F, Cl, Br) molecules and the results were compared to the corresponding isothiocyanate molecules. The predicted frequencies for the fundamentals of the XNCO molecules compare favorably to the experimental values but some of the predicted intensities differ significantly from those in the observed spectra. The two OCN bends for HOCN have been assigned and the frequencies for the two corresponding fundamentals of DOCN are predicted.     

The acetyl CoA synthase paradigm for hybrid bio-organometallics: Quantitative measures for resin-bound Ni-Rh complexes

The active site of Acetyl CoA Synthase utilizes a square planar NiN₂S₂ complex in the form of Ni^II(CGC)²⁻ (CGC = the cysteine-glycine-cysteine tripeptide motif within the protein) to serve as a bidentate sulfur-donor ligand to chelate a second, catalytically active Ni atom responsible for the C-C and C-S coupling reactions for the production of Acetyl CoA. Metalloenzymes, such as this, which house stable catalytic complexes within intricately designed pockets accessible by solvent channels, have inspired design of resin-bound complexes. Through the use of TentaGel S-RAM^® resin beads, the O-Ni(CGC)²⁻ ligand has been synthesized and derivatized with the Rh^I(CO)₂ moiety. The identification of the adduct on these resin beads is afforded by attenuated total reflectance FTIR spectroscopy in the ν(CO) region and compared to solution analogues. The goal of this study is to establish a quantitative measure of the loading of nickel and rhodium on the tripeptide modified resin beads, O-(CGC). The extent of CGC derivatization was determined by Fmoc cleavage of the Fmoc protected O-(CGC). Nickel and rhodium loading were determined by Neutron Activation Analysis. This work provides evidence that the TentaGel S-RAM^® resin beads greatly decrease the air sensitivity of the Ni-Rh complex as compared to the unsupported solution phase analogue. The derivatized beads have also been studied for their ability to withstand a number of physical stresses, i.e., for leaching.     

Capillary electrophoresis procedure for the simultaneous analysis and stoichiometry determination of a drug and its counter-ion by using dual-opposite end injection and contactless conductivity detection: Application to labetalol hydrochloride

In this work, a capillary electrophoresis (CE) procedure was developed for the simultaneous determination of a pharmaceutical drug and its counter-ion, namely labetalol hydrochloride. For this purpose, an uncoated fused-silica capillary, a low conductivity background electrolyte (BGE) and a capacitively coupled contactless conductivity detector (C⁴D) were employed. This detection system is highly sensitive and enables detection of inorganic as well as organic ions unlike with direct UV detection. Moreover, to be able to simultaneously analyze the cationic drug (labetalol⁺) and its anionic counter-ion (Cl⁻) in the same electrophoretic run without the need of a coated capillary, a dual-opposite end injection was performed. In this technique, the sample is hydrodynamically injected into both ends of the capillary. This method is simple and easy to perform since the different injection steps are automated by the CE software.This novel CE-C⁴D procedure with dual-opposite end injection has been successfully validated and applied for the analysis of chloride content in an adrenergic antagonist (labetalol hydrochloride). Thus, the hereby developed method has been shown to enable fast (analysis time < 10 min), precise (repeatability of migration times < 0.7% and of corrected-peak areas < 3.3%; n = 6) and rugged analyses for the simultaneous determination of a pharmaceutical drug and its counter-ion.     

Catalytic adsorptive stripping voltammetry versus electrothermal atomic absorption spectrometry in the determination of trace cobalt and chromium in human urine

Two methods of the determination of cobalt and chromium in human urine of non-occupationally exposed populations—highly sensitive catalytic adsorptive stripping voltammetry (CAdSV) and electrothermal atomic absorption spectrometry (ET-AAS)—are evaluated and compared. The CAdSV methods are based on adsorptive accumulation of a cobalt-nioxime (1,2-cyclohexanedione dioxime) or a chromium-DTPA (diethylenetriammine-N,N,N′,N″,N″-pentaacetic acid) complexes on a hanging mercury drop electrode, followed by a stripping voltammetric measurement of the catalytic reduction current of the adsorbed complex in the presence of sodium nitrite in case of cobalt or in the presence of sodium nitrate in case of chromium determination. In the CAdSV procedure UV-photolysis was used for the sample pre-treatment; the ET-AAS determination did not require any separate preliminary decomposition of the analyte urine samples. The accuracy of the procedures was checked by the analysis of commercially available quality control urine samples. The detection limits (3σ) were 0.13 μg l⁻¹ for Co and 0.18 μg l⁻¹ for Cr in ET-AAS determination and 0.007 μg l⁻¹ for Co and 0.002 μg l⁻¹ for Cr in CAdSV measurements. Precision (R.S.D.) was less than 5% for both methods. The study has shown that the CAdSV is a more reliable and sensitive technique for the determination of very low cobalt and chromium contents in urine, the detection of which is not possible when using the AAS technique.     

Complex formation equilibria between Ag(I) and thioureas in n-propanol

Complex formation equilibria between Ag(I) and thiourea or N-alkyl-substituted thioureas have been investigated in n-propanol by potentiometry at 10 °C intervals from 5 to 50 °C. Stepwise formation of tris-coordinated AgL_n (n = 1-3) complexes has been found for the majority of the ligands. ΔH and ΔS values for the complex formation reactions have been evaluated from the dependence of ln β_n on temperature. The alkyl-substituents affect the ligand affinities in different ways in relation with the coordination level n.The reactions are exothermic with few exceptions. Enthalpy favoured complex formation with negative dependence of ΔG on temperature (ΔS > 0) have been found.The enthalpy and entropy changes for the stepwise complex formation equilibria are correlated by two linear compensative relationships with the same isoequilibrium temperature 50-51 °C.     

Synthesis, vacuum ultraviolet and near ultraviolet-excited luminescent properties of GdCaAl3O7: RE (RE=Eu, Tb)

Vacuum ultraviolet (VUV) excitation and photoluminescent (PL) properties of Eu³⁺ and Tb³⁺ ion-doped aluminate phosphors, GdCaAl₃O₇:Eu³⁺ and GdCaAl₃O₇:Tb³⁺ have been investigated. X-ray diffraction (XRD) patterns indicate that the phosphor GdCaAl₃O₇ forms without impurity phase at 900 °C. Field emission scanning electron microscopy (FE-SEM) images show that the particle size of the phosphor is less than 3 μm. Upon excitation with VUV irradiation, the phosphors show a strong emission at around 619 nm corresponding to the forced electric dipole ⁵D₀→⁷F₂ transition of Eu³⁺, and at around 545 nm corresponding to the ⁵D₄→⁷F₅ transition of Tb³⁺. The results reveal that both GdCaAl₃O₇:RE³⁺ (RE=Eu, Tb) are potential candidates as red and green phosphors, respectively, for use in plasma display panel (PDP).     

Flow system to gas capture from a nebulized solution

The use of aerosol produced in a nebulization chamber is proposed as an alternative to gas sample capture in flow systems. This paper describes the coupling of a sampling interface with a flow system, for in situ gas monitoring. Aspects related with the behavior of aerosol formation and gas solubilization in liquid drops are discussed. The method is applied to the determination of residual lime in acidic soils. Aliquots of 5.0 ml of 1.0 mol l⁻¹ HCl were mixed with soil samples (1 g). The CO₂ released from these samples was captured by a nebulized aerosol and determined conductivity. The analytical curve from 1.0×10⁻² to 5.0×10⁻² mol kg⁻¹ CaCO₃ was ploted applying the matrix matching approach. This proposition, allowed an increase in the sensibility with detection limit of 6.0×10⁻³ mol kg⁻¹. The precision was good (R.S.D. <3%) for an analytical frequency of 22 determinations per hour. A fair agreement, at 95% confidence level, was found between the results from the proposed method and certified values of the investigated samples.     

Advantages of using a modified orthogonal sampling configuration originally designed for LC-ESI-MS to couple CE and MS for the determination of antioxidant phenolic compounds found in virgin olive oil

A ThermoFinnigan sheath liquid flow capillary electrophoresis-mass spectrometry system designed for coupling via a co-axial interface was coupled through an adapted via an alternative, commercially available interface for orthogonal sampling. The affordable, reversible structural alterations made in the commercial LC-MS interface resulted in improved analytical performance.The results of a conventional capillary electrophoresis (CE) method using a commercial co-axial source to determine antioxidant phenolic acids present in virgin olive oil, were compared with those obtained by using a modified orthogonal sampling position. In both cases, separations were done using a 10 mM ammonium acetate/ammonium hydroxide buffer solution at pH 10.0 and a constant applied voltage of 25 kV. The operating variables for the mass spectrometry interface were re-optimized for the modified orthogonal orientation. This allowed the sheath liquid, sheath gas flow rates and capillary voltage to be lowered with respect to the co-axial coupling configuration. In addition, the orthogonal sampling position provided a higher selectivity by effect of ion sampling excluding larger droplets—with an increased momentum along the axis—which were drained through the sink at the bottom of the ion source. Also, the new configuration facilitated sample ionization, improved electrospray stability and led to stronger signals as a result.The new system was validated in terms of precision (repeatability), linearity, and limits of detection and quantification. A comparison of the validation data with the results previously obtained by using a commercial co-axial configuration revealed the adapted orthogonal sampling position to provide better repeatability in both migration times and relative peak areas (<1% and 7% respectively with n = 15 replicates), a good linear range (with levels in the microgram-per-litre region) and lower limits of detection—especially for the compounds detected with the lowest sensitivity when co-axial ESI was used, as HFA, GEN, FER and VAN finding LOD among 24-3.0 μg L⁻¹ respectively.