A novel fused-silica capillary dropping mercury electrode with long drop-time and its application on determination of critical micelle concentration

A novel long drop time mercury electrode has been constructed from common fused-silica capillary (50 μm I.D., 360 μm E.D.). Proposed device provides reproducible mercury drops with typical lifetime 40-120 s. The electrode was used for a set of electrocapillary measurements aimed at determination of critical micelle concentration of anionic surfactants by a convection controlled drop-time technique. A critical micelle concentration of sodium dodecyl sulfate 5.6 ± 0.4 mmol L⁻¹ and 4.3 ± 0.4 mmol L⁻¹ were obtained in 1 mmol L⁻¹ and 5 mmol L⁻¹ phosphate buffer (pH 7.0), respectively. The values were comparable to those obtained from conductometric measurements under the same conditions (7.0 ± 0.1 mmol L⁻¹ and 5.2 ± 0.1 mmol L⁻¹, respectively) and the difference was explained in accordance with theory of hemi-micelle formation.     

Determination of phosphoamino acids by micellar electrokinetic capillary chromatography with laser-induced fluorescence detection

A micellar electrokinetic capillary chromatography (MEKC) method with laser-induced fluorescence detection (LIF) was developed for analyzing three phosphoamino acids including phosphotyrosine (P-Tyr), phosphoserine (P-Ser), and phosphothreonine (P-Thr). 3-(2-Furoyl)quinoline-2-carboxaldehyde (FQ), a fluorogenic dye, was employed for derivatization of these phosphoamino acids. Results indicated that the complete baseline resolution of each phosphoamino acid was obtained within 10 min, using 20 mmol l⁻¹ sodium borate buffer (pH 9.35) containing 20 mmol l⁻¹sodium deoxycholate (SDC) and 10 mmol l⁻¹ Brij35. Other common amino acids, especially Glu and Asp, did not disturb the assay of these phosphoamino acids. There was a linear relationship between the peak area for analyte and its concentration, with correlation coefficients in the range of 0.9966-0.9996. The concentration detection limits (signal-to-noise = 3) for P-Tyr, P-Ser, and P-Thr were 10, 40, and 75 nmol l⁻¹, respectively. The developed method was successfully applied for determining phosphoamino acids in the hydrolysis sample of a phosphorylated protein kinase.     

Simple and fast spectrophotometric determination of H(2)O(2) in photo-Fenton reactions using metavanadate

This work proposes a spectrophotometric method for the determination of hydrogen peroxide during photodegradation reactions. The method is based on the reaction of H₂O₂ with amonium metavanadate in acidic medium, which results in the formation of a red-orange color peroxovanadium cation, with maximum absorbance at 450 nm. The method was optimized using the multivariate analysis providing the minimum concentration of vanadate (6.2 mmol L⁻¹) for the maximum absorbance signal. Under these conditions, the detection limit is 143 μmol L⁻¹. The reaction product showed to be very stable for samples of peroxide concentrations up to 3 mmol L⁻¹ at room temperature during 180 h. For higher concentrations however, samples must be kept refrigerated (4 °C) or diluted. The method showed no interference of Cl⁻ (0.2-1.3 mmol L⁻¹), NO₃⁻ (0.3-1.0 mmol L⁻¹), Fe³⁺ (0.2-1.2 mmol L⁻¹) and 2,4-dichlorophenol (DCP) (0.2-1.0 mmol L⁻¹). When compared to iodometric titration, the vanadate method showed a good agreament. The method was applied for the evaluation of peroxide consumption during photo-Fenton degradation of 2,4-dichlorophenol using blacklight irradiation.     

Simultaneous Analysis of Isoniazid and Its Impurities by CZE

An alternative methodology for simultaneous determination of isoniazid, isonicotinic acid, 4-cyanopyridine, ethyl isonicotinate and isonicotinamide by capillary zone electrophoresis, within an analysis time of 11 min, is proposed. An electrolyte composed by 50 mmol L⁻¹ of acetic acid/sodium acetate buffer and 12.5 mmol L⁻¹ of Cu²⁺, an analyte dilution in 1 mmol L⁻¹ of Brij 35 and 12.5 mmol L⁻¹ of Cu²⁺ and +20 kV voltage were optimized. After evaluating some figures of merit, such as linearity, precision, recovery and quantification limit, the method was successfully applied to the isoniazid analysis in tablets. The contents found were 99.3 mg of isoniazid and 0.3 mg of isonicotinic acid, corresponding to 0.3 % of impurity regarding the content of the active ingredient in the pharmaceutical formulation.

     

Studying the distribution pattern of selenium in nut proteins with information obtained from SEC-UV-ICP-MS and CE-ICP-MS

In this work, size exclusion chromatography (SEC) with UV and inductively coupled plasma mass spectrometry (ICP-MS) detection was used to study the association of selenium to proteins present in Brazil nuts (Bertholletia excelsa) under five different extraction conditions. As expected, better solubilization of proteins was observed using 0.05 mol L⁻¹ sodium hydroxide and 1% sodium dodecylsulfate (SDS) in Tris/HCl buffer (0.05 mol L⁻¹, pH 8) as compared to 0.05 mol L⁻¹ HCl, 0.05 mol L⁻¹ Tris/HCl or hot water (60 °C). Due to non-destructive character of Tris-SDS treatment, this was applied for studying molecular weight (MW) distribution patterns of selenium-containing nut proteins. Three different SEC columns were used for obtaining complete MW distribution of selenium: Superdex 75, Superdex Peptide, and Superdex 200 were tested with 50 mmol L⁻¹ Tris buffer (pH 8), 150 mmol L⁻¹ ammonium bicarbonate buffer (pH 7.8), phosphate (pH 7.5), and CAPS (pH 10.0) mobile phases. Using Superdex 200 column, the elution of at least three MW fractions was observed with UV detection (200-10 kDa) and ICP-MS chromatogram showed the co-elution of selenium with the two earlier fractions. The apparent MWs of these selenium-containing fractions were respectively about 107 and 50 kDa, as evaluated from the column calibration. For further characterization of individual selenium species, the defatted nuts were hydrolyzed with proteinase K and analyzed by capillary electrophoresis (CE) with ICP-MS detection. The suitability of CE for the separation of selenite, selenate, selenocystine and selenomethionine in the presence of the nut sample matrix is demonstrated. Complete separation of the above mentioned selenium species was obtained within a migration time of 7 min. In the analysis of nut extracts with CE-ICP-MS, selenium was found to be present mainly as selenomethionine.     

Analysis of microcystins by capillary zone electrophoresis coupling with electrospray ionization mass spectrometry

In this paper, a rapid and effective method based on capillary zone electrophoresis (CZE) coupled with electrospray ionization mass spectrometry (ESI-MS) was established for the trace analysis of microcystin (MC) isomers in crude algae sample. The experimental conditions including the composition, acidity and concentration of buffer, separation voltage, injection time, and MS detection parameters were investigated in detail. A capillary separation system was as follows: a uncoated fused-silica capillary tube (50 μm i.d. × 90 cm), 40 mmol L⁻¹ ammonium acetate solution (pH 9.86) as running buffer, 25 kV as separation voltage, 20 kV × 3 s water first and 20 kV × 20 s for sample injection. Mass analysis was performed in ESI source, with sheath gas temperature 150 °C, sheath gas pressure 10 psi, and sheath gas flow 6 L min⁻¹. And sheath liquid was 7.5 mmol L⁻¹ acetic acid in 50% isopropanol-water (3 μL min⁻¹). Protonation and ammonium adduct molecular ions m/z 506.9 (MC-LR) and 532.0 (MC-YR) were used for the quantification of MCs. Under these conditions, two MCs were baseline separated within 9 min, the calibration curves were obtained in the range of 0.11-10.0 μg mL⁻¹ and 0.16-10.5 μg mL⁻¹ for MC-LR and MC-YR, respectively. Meanwhile, limits of detection were 0.05 and 0.08 μg mL⁻¹ for MC-LR and MC-YR, respectively. The recoveries for the two MCs were in the range of 95.8-108%. The developed approach had been successfully applied to the analysis of MCs in crude algae samples.     

Development of a D-amino acids electrochemical sensor based on immobilization of thermostable D-proline dehydrogenase within agar gel membrane

A novel biosensor for determination of d-amino acids (DAAs) in biological samples by using an electrode based on immobilization of a thermostable d-Proline dehydrogenase (d-Pro DH) within an agar gel membrane was developed. The electrode was simply prepared by spin-coating the agar solution with the d-Pro DH on a glassy carbon (GC) electrode.An electrocatalytic oxidation current of 2,6-dichloroindophenol (DCIP) was observed at −100 mV vs. Ag/AgCl with the addition of 5 and 20 mmol L⁻¹d-proline. The current response and its relative standard deviation were 0.15 μA and 7.6% (n = 3), respectively, when it was measured in a pH 8.0 phosphate buffer solution containing 10 mmol L⁻¹d-proline and 0.5 mmol L⁻¹ DCIP at 50 °C. The current response of d-proline increased with increase of the temperature of the sample solution up to 70 °C. The electrocatalytic response at the d-Pro DH/agar immobilized electrode subsequently maintained for 80 days. Finally, the d-Pro DH/agar immobilized electrode was applied to determination of DAAs in a human urine sample. The determined value of DAAs in the human urine and its R.S.D. were 1.39 ± 0.12 mmol L⁻¹ and 8.9% (n = 3), respectively.     

Micellar electrokinetic biofluid analysis of biogenic amines using on-line sample concentration and UV laser-induced native fluorescence detection

A simple and sensitive sweeping micellar electrokinetic chromatography method coupled with UV laser-induced native fluorescence detection has been developed for quantitative analysis of biogenic amines in biofluids. The background electrolyte comprised 30 mmol L⁻¹ phosphoric acid and 20 mmol L⁻¹ sodium dodecyl sulfate. The concentration limits of detection of analytes using sweeping-micellar electrokinetic chromatography (sweeping-MEKC) were in the range 7–100 nmol L⁻¹, which were 250–3600-fold improvement for dopamine, DOPA and epinephrine compared with conventional capillary zone electrophoresis. An improvement of approximately 20-fold was observed for all analytes compared with typical micellar electrokinetic chromatography conditions. Baseline separation was achieved for the all analytes within 12 min and migration-time and peak-area repeatability were better than RSD 0.35% and 5.68%, respectively. The developed method was applied to measure the biogenic amines in biofluids extracted from wheat phloem sap, human plasma and human urine.     

Implementing stepwise solvent elution in sequential injection chromatography for fluorimetric determination of intracellular free amino acids in the microalgae Tetraselmis gracilis

The concept of sequential injection chromatography (SIC) was exploited to automate the fluorimetric determination of amino acids after pre-column derivatization with o-phthaldialdehyde (OPA) in presence of 2-mercaptoethanol (2MCE) using a reverse phase monolithic C₁₈ stationary phase. The method is low-priced and based on five steps of isocratic elutions. The first step employs the mixture methanol: tetrahydrofuran: 10 mmol L⁻¹ phosphate buffer (pH 7.2) at the volumetric ratio of 8:1:91; the other steps use methanol: 10 mmol L⁻¹ phosphate buffer (pH 7.2) at volumetric ratios of 20:80, 35:65, 50:50 and 65:35. At a flow rate of 10 μL s⁻¹ a 25 mm long-column was able to separate aspartic acid (Asp), glutamic acid (Glu), asparagine (Asn), serine (Ser), glutamine (Gln), glycine (Gly), threonine (Thr), citruline (Ctr), arginine (Arg), alanine (Ala), tyrosine (Tyr), phenylalanine (Phe), ornithine (Orn) and lysine (Lys) with resolution >1.2 as well as methionine (Met) and valine (Val) with resolution of 0.6. Under these conditions isoleucine (Ile) and leucine (Leu) co-eluted. The entire cycle of amino acids derivatization, chromatographic separation and column conditioning at the end of separation lasted 25 min. At a flow rate of 40 μL s⁻¹ such time was reduced to 10 min at the cost of resolution worsening for the pairs Ctr/Arg and Orn/Lys. The detection limits varied from 0.092 μmol L⁻¹ for Tyr to 0.51 μmol L⁻¹ for Orn. The method was successfully applied to the determination of intracellular free amino acids in the green alga Tetraselmis gracilis during a period of seven days of cultivation. Samples spiked with known amounts of amino acids resulted in recoveries between 94 and 112%.     

A sensitive post-column photochemical derivatization/fluorimetric detection system for HPLC determination of bisphosphonates

A new reversed-phase ion-pair high-performance liquid chromatographic (HPLC) method has been developed for the determination of the following bisphosphonic acids: alendronic acid (ALEN), etidronic acid (ETID), ibandronic acid (IBAN) and risedronic acid (RISE). Separation was achieved on a C₁₈ column using a mixture of 50 mmol L⁻¹ borate buffer pH 9.0 containing 0.25 mmol L⁻¹ tetrabutylammonium chloride and 0.5 mmol L⁻¹ EDTA and acetonitrile (97:3) as the mobile phase. The sensitive detection of the above bisphosphonic acids was based on their oxidation to orthophosphate by the on-line peroxydisulfate-assisted photolysis followed by post-column reaction with molybdate to yield phosphomolybdate. This subsequently reacted with thiamine to generate thiochrome and, finally, the fluorescence of thiochrome was measured at 440 nm with excitation at 375 nm. The developed method is precise with a mean relative standard deviation of 1.3%, sensitive (with a detection limit at the nmol L⁻¹ level), accurate, specific, rapid (analysis time approximately 13 min) and inexpensive because to the low cost of the reagents. The assay was applied to the analysis of the four bisphosphonic acids in commercial dosage formulations, in which the excipients did not interfere with the determination. The method was also applied to the determination of etidronate, risedronate and ibandronate in human urine. Sample preparation involves precipitation of the analytes from urine along with endogenous phosphates such as calcium salts by addition of calcium chloride at alkaline pH and dissolution of the precipitate in 0.05 mol L⁻¹ ethylene glycol-bis(β-aminoethyl ether)-N,N,N′,N′-tetraacetic acid.     

Sulfonylcalix[4]arenetetrasulfonate as pre-column chelating reagent for selective determination of aluminum(III), iron(III), and titanium(IV) by ion-pair reversed-phase high-performance liquid chromatography with spectrophotometric detection

Sulfonylcalix[4]arenetetrasulfonate (SO₂CAS) has been examined as a pre-column chelating reagent for ultratrace determination of metal ions by ion-pair reversed-phase high-performance liquid chromatography with spectrophotometric detection. Metal ions were converted into the SO₂CAS chelates in an acetic buffer solution (pH 4.7). The chelates were injected onto a n-octadecylsilanized silica-type Chromolith™ Performance RP-18e column and were eluted using a methanol (50 wt.%)-water eluent (pH 5.6) containing tetra-n-butylammonium bromide (7.0 mmol kg⁻¹), acetate buffer (5.0 mmol kg⁻¹), and disodium ethylendiamine-N,N,N′,N′-tetraacetate (0.10 mmol kg⁻¹). Under the conditions used, Al(III), Fe(III), and Ti(IV) were selectively detected among 21 kinds of metal ions [Al(III), Ba(II), Be(II), Ca(II), Cd(II), Co(II), Cr(III), Cu(II), Fe(III), Ga(III), Hf(IV), In(III), Mg(II), Mn(II), Mo(VI), Ni(II), Pb(II), Ti(IV), V(V), Zn(II), and Zr(IV)]. The detection limits on a 3σ blank basis were 8.8 nmol dm⁻³ (0.24 ng cm⁻³) for Al(III), 7.6 nmol dm⁻³ (0.42 ng cm⁻³) for Fe(III), and 17 nmol dm⁻³ (0.80 ng cm⁻³) for Ti(IV). The practical applicability of the proposed method was checked using river and tap water samples.     

Highly sensitive catalytic determination of molybdenum

A novel, highly sensitive, selective, and simple kinetic method was developed for the determination of Mo(VI) based on its catalytic effect on the oxidation of 1-amino-2-naphthol-4-sulfonic acid (ANSA) with H₂O₂. The reaction was followed spectrophotometrically by tracing the oxidized product at 465 nm after 30 min of mixing the reagents. The optimum reaction conditions were: 10 mmol l⁻¹ ANSA, 50 mmol l⁻¹ H₂O₂, 100 mmol l⁻¹ acetate buffer of pH 5.0 ± 0.05 and at 40 °C. Addition of 200 μg ml⁻¹ diethylenetriaminepentaacetic acid (DTPA) conferred high selectivity for the proposed method. Following the recommended procedure, Mo(VI) could be determined with a linear calibration graph up to 2.5 ng ml⁻¹ and a detection limit, based on the 3S_b-criterion, of 0.027 ng ml⁻¹. The unique sensitivity and selectivity of the implemented method allowed its direct application to the determination of Mo(VI) in natural and industrial waste water. The method was validated by comparison with the standard ETAAS method. Moreover, published catalytic-spectrophotometric methods for the determination of molybdenum were reviewed.     

Zwitterionic hydrophilic interaction chromatography coupled with post-column derivatization for the analysis of glutathione in wine samples

In this study the development, validation and application of a new chromatographic method for the determination of glutathione (GSH) in wine samples is presented. The separation of the GSH was carried out using a sulfobetaine-based hydrophilic interaction chromatography (HILIC) analytical column whereas its detection was carried out spectrofluorimetrically (λ_ext/λ_em = 340/455 nm) after post-column derivatization with o-phthalaldehyde. GSH was separated efficiently from matrix endogenous compounds of wines by using a mobile phase of 15 mmol L⁻¹ CH₃COONH₄ (pH = 2.5)/CH₃CN, 35/65% (v/v). The parameters of the post-column reaction (pH, amount concentration of the reagent and buffer solution, flow rate, length of the reaction coil) were investigated. The linear determination range for GSH was 0.25–5.0 μmol L⁻¹ and the LOD was 19 nmol L⁻¹. No matrix effect was observed, while the accuracy was evaluated with recovery experiments and was ranged between 89% and 108%.     

A novel ion-pairing chromatographic method for the simultaneous determination of both nicarbazin components in feed additives: chemometric tools for improving the optimization and validation

The development, optimization and validation of an ion-pairing high performance liquid chromatography method for the simultaneous determination of both nicarbazin (NIC) components: 4,4′-dinitrocarbanilide (DNC) and 2-hydroxy-4,6-dimethylpyrimidine (HDP) in bulk materials and feed additives are described. An experimental design was used for the optimization of the chromatographic system. Four variables, including mobile phase composition and oven temperature, were analyzed through a central composite design exploring their contribution to analyte separation. Five responses: peak resolutions, HDP capacity factor, HDP tailing and analysis time, were modelled by using the response surface methodology and were optimized simultaneously by implementing the desirability function. The optimum conditions resulted in a mobile phase consisting of 10.0 mmol L⁻¹ of 1-heptanesulfonate, 20.0 mmol L⁻¹ of sodium acetate, pH = 3.30 buffer and acetonitrile in a gradient system at a flow rate of 1.00 mL min⁻¹. Column was an INERSTIL ODS-3 (4.6 mm × 150 mm, 5 μm particle size) at 40.0 °C. Detection was performed at 300 nm by a diode array detector. The validation results of the method indicated a high selectivity and good precision characteristics, with RSD less than 1.0% for both components, both in intra and inter-assay precision studies. Linearity was proved for a range of 32.0-50.0 μg mL⁻¹ of NIC in sample solution. The recovery, studied at three different fortification levels, varied from 98.0 to 101.4 for HDP and from 99.1 to 100.2 for DNC. The applicability of the method was demonstrated by determining DNC and HDP content in raw materials and commercial formulations used for coccidiosis prevention. Assays results on real samples showed that considerable differences in molecular ratio DNC:HDP exist among them.     

A luminescence-based probe for sensitive detection of hydrogen peroxide in seconds

Here, we present a fast and simple hydrogen peroxide assay that is based on time-resolved fluorescence. The emission intensity of a complex consisting of terbium ions (Tb³⁺) and phthalic acid (PA) in HEPES buffer is quenched in the presence of H₂O₂ and this quenching is concentration-dependent. The novel PATb assay detects hydrogen peroxide at a pH range from 7.5 to 8.5 and with a detection limit of 150 nmol L⁻¹ at pH 8.5. The total assay time is less than 1 min. The linear range of the assay can be adapted by a pH adjustment of the aqueous buffer and covers a concentration range from 310 nmol L⁻¹ to 2.56 mmol L⁻¹ in total which encompasses four orders of magnitude. The assay is compatible with high concentrations of all 47 tested inorganic and organic compounds. The PATb assay was applied to quantify H₂O₂ in polluted river water samples. In conclusion, this fast and easy-to-use assay detects H₂O₂ with high sensitivity and precision.     

Development and validation of a stability-indicating RP-HPLC method for the determination of paracetamol with dantrolene or/and cetirizine and pseudoephedrine in two pharmaceutical dosage forms

A stability-indicating reversed-phase high-performance liquid chromatography (RP-HPLC) method has been developed which can separate and accurately quantitate paracetamol, dantrolene, cetirizine and pseudoephedrine. The method was successfully validated for the purpose of conducting stability studies of the four analytes in quality control (QC) laboratories. The stability-indicating capability of the method was demonstrated by adequate separation of these four analytes from all the degradant peaks. A gradient mobile phase system consisting of (A) 50 mmol L⁻¹ sodium dihydrogen phosphate, 5 mmol L⁻¹ heptane sulfonic acid sodium salt, pH 4.2 and (B) acetonitrile was used with Discovery reversed-phase HS C₁₈ analytical column (250 mm × 4.6 mm i.d., 5 μm particle size). Quantitation was achieved with UV detection at 214 nm, based on peak area.The proposed method was validated and successfully applied for the analysis of pharmaceutical formulations and laboratory-prepared mixtures containing the two multicomponent combinations.     

A potential high-throughput method for the determination of lipase activity by potentiometric flow injection titrations

Potentiometric FIA titrations were performed to determine enzyme activities of lipase type B from Candida antarctica, CAL-B. Two substrates, triacetin and tributyrin were hydrolyzed in phosphate buffer solutions, and the concentration change of the base component of the buffer was titrated in a carrier solution containing hydrochloric acid and potassium chloride. The system was calibrated with butyric acid and acetic acid, respectively. FIA titration peaks were evaluated with respect to peak height and peak area. Butyric acid and acetic acid could be titrated in the buffer solution from 3 × 10⁻³ mol L⁻¹ to 0.1 mol L⁻¹. The detection limit of enzyme activity was determined to be 0.07 U mL⁻¹ (15 min reaction time) and the minimum activity was calculated to be 0.035 units corresponding to 35 nmol min⁻¹. The specific activities of lipase B for the hydrolysis of tributyrin and triacetin were determined as 16 ± 2 U mg⁻¹ and 2 ± 0.2 U mg⁻¹ (per mg commercial lipase preparation), respectively.     

Catalytic-adsorptive stripping voltammetric determination of ultra-trace iridium(III). Application to fresh- and sea-water

An extremely sensitive stripping voltammetric procedure for ultra-trace determination of iridium(III) is reported. The method is based on the interfacial accumulation of the iridium(III)-CTAB complex onto the glassy carbon electrode, followed by the catalytic reduction of the adsorbed complex in the presence of bromate. 0.3 mol L⁻¹ acetate buffer pH 4.7 + 6.9 × 10⁻² mol L⁻¹ NaBrO₃ + 2.7 × 10⁻⁵ mol L⁻¹ cetyltrimethylammonium bromide (CTAB) + 0.2 mol L⁻¹ KCl was employed as the supporting electrolyte.The analytical procedure was verified by the analysis of the standard reference materials: Sea Water BCR-CRM 403 and Fresh Water NIST-SRM 1643d.The accuracy, expressed as relative error e%, was satisfactory, being lower than 6%, while precision as repeatability, expressed as relative standard deviation s_r%, was generally lower than 5%. The limit of detection was of the order of 2-3 ng L⁻¹.Once set up on the standard reference materials, the analytical procedure was transferred and applied to superficial water sampled in proximity to superhighway and in the Po river mouth area.     

Direct electrochemistry with enhanced electrocatalytic activity of hemoglobin in hybrid modified electrodes composed of graphene and multi-walled carbon nanotubes

A graphene (GR) and multi-walled carbon nanotubes (MWCNT) hybrid was prepared and modified on a 1-hexylpyridinium hexafluorophosphate based carbon ionic liquid electrode (CILE). Hemoglobin (Hb) was immobilized on GR-MWCNT/CILE surface with Nafion as the film forming material and the modified electrode was denoted as Nafion/Hb-GR-MWCNT/CILE. Spectroscopic results revealed that Hb molecules retained its native structure in the GR-MWCNT hybird. Electrochemical behaviors of Hb were carefully investigated by cyclic voltammetry with a pair of well-defined redox peaks obtained, which indicated that direct electron transfer of Hb was realized in the hybrid modified electrode. The result could be attributed to the synergistic effects of GR-MWCNT hybrid with enlarged surface area and improved conductivity through the formation of a three-dimensional network. Electrochemical parameters of the immobilized Hb on the electrode surface were further calculated with the results of the electron transfer number (n) as 1.03, the charge transfer coefficient (a) as 0.58 and the electron-transfer rate constant (k_s) as 0.97 s⁻¹. The Hb modified electrode showed good electrocatalytic ability toward the reduction of different substrates such as trichloroacetic acid in the concentration range from 0.05 to 38.0 mmol L⁻¹ with a detection limit of 0.0153 mmol L⁻¹ (3σ), H₂O₂ in the concentration range from 0.1 to 516.0 mmol L⁻¹ with a detection limit of 34.9 nmol/L (3σ) and NaNO₂ in the concentration range from 0.5 to 650.0 mmol L⁻¹ with a detection limit of 0.282 μmol L⁻¹ (3σ). So the proposed electrode had the potential application in the third-generation electrochemical biosensors without mediator.     

Development of a flow system for the determination of cadmium in fuel alcohol using vermicompost as biosorbent and flame atomic absorption spectrometry

In this study a method for the determination of cadmium in fuel alcohol using solid-phase extraction with a flow injection analysis system and detection by flame atomic absorption spectrometry was developed. The sorbent material used was a vermicompost commonly used as a garden fertilizer. The chemical and flow variables of the on-line preconcentration system were optimized by means of a full factorial design. The selected factors were: sorbent mass, sample pH, buffer concentration and sample flow rate. The optimum extraction conditions were obtained using sample pH in the range of 7.3-8.3 buffered with tris(hydroxymethyl)aminomethane at 50 mmol L⁻¹, a sample flow rate of 4.5 mL min⁻¹ and 160 mg of sorbent mass. With the optimized conditions, the preconcentration factor, limit of detection and sample throughput were estimated as 32 (for preconcentration of 10 mL sample), 1.7 μg L⁻¹ and 20 samples per hour, respectively. The analytical curve was linear from 5 up to at least 50 μg L⁻¹, with a correlation coefficient of 0.998 and a relative standard deviation of 2.4% (35 μg L⁻¹, n = 7). The developed method was successfully applied to spiked fuel alcohol, and accuracy was assessed through recovery tests, with recovery ranging from 94% to 100%.