Acetamide/SO2Cl2 as an efficient reagent for Friedel–Craft’s acylation of aromatic compounds under ultrasonic and microwave conditions

Acetamide/SO₂Cl₂ reagent has been developed for effective Friedel–Craft’s acylation of aromatic compounds. Acylation of aromatic compounds with acetamide/SO₂Cl₂ was much more effective and faster than analogous (acetamide/SOCl₂) and (acetamide/POCl₃) reagents even under conventional conditions. However, microwave and ultrasonic assisted reactions afforded high yields of products in very short reaction times (30–40 min under sonication and 3–4 min under microwave assisted conditions).     

Cr2O3-modified ZnO thick film resistors as LPG sensors

Thick films of pure ZnO were obtained by screen-printing technique. Surface functionalized ZnO thick films by Cr₂O₃ were obtained by dipping pure ZnO thick films into 0.01 M aqueous solution of chromium trioxide (CrO₃). The dipped films were fired at 500 °C for 30 min. Upon firing, the CrO₃ would reduce to Cr₂O₃. Cr₂O₃-activated (0.47 mass%) ZnO thick films resulted in LPG sensor. Upon exposure to 100 ppm LPG, the barrier height between Cr₂O₃ and ZnO grains decreases markedly, leading to a drastic decrease in resistance. The sensor was found to sense LPG at 350 °C and no cross sensitivity was observed to other hazardous, polluting and inflammable gases. The quick response (∼18 s) and fast recovery (∼42 s) are the main features of this sensor. The effects of microstructures and dopant concentrations on the gas sensing performance of the sensor were studied and discussed.     

Identification of control parameters for the sulfur gas storability with bag sampling methods

Air samples containing sulfur compounds are often collected and stored in sample bags prior to analysis. The storage stability of six gaseous sulfur compounds (H₂S, CH₃SH, DMS, CS₂, DMDS and SO₂) was compared between two different bag materials (polyvinyl fluoride (PVF) and polyester aluminum (PEA)) at five initial concentrations (1, 10, 100, 1000, and 10,000 ppb). The response factors (RF) of these samples were determined after storage periods of 0, 1, and 3 days by gas chromatography–pulsed flame photometric detector (GC–PFPD) combined with an air server (AS)/thermal desorber (TD) system. Although concentration reduction occurred more rapidly from samples of the high concentration standards (1000 and 10,000 ppb), such trends were not evident in their low concentration counterparts (1, 10, and 100 ppb). As such, temporal changes in RF values and the associated loss rates of most sulfur gases were greatly affected by their initial concentration levels. Moreover, the storability of oxidized sulfur compound (SO₂) was greatly distinguished from that of reduced sulfur compounds (RSCs), as the former almost disappeared in the PVF bag even after one day. The results of our study confirm that storability of gaseous sulfur species is affected interactively by such variables as initial gas concentration level, bag material type, and oxidation status with the associated reactivity.     

One-step immobilization of tris(2,2'-bipyridyl)ruthenium(II) via vapor-surface sol-gel deposition towards solid-state electrochemiluminescence detection

A novel method for immobilization of tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃Cl₂) on electrode surfaces based on the vapor-surface sol-gel deposition strategy is first demonstrated in this paper. Ru(bpy)₃Cl₂ immobilized sol-gel (Ru(bpy)₃Cl₂/sol-gel) films were characterized by UV-vis spectroscopy and field-emitted scanning electron microscopy (FE-SEM). These results showed that Ru(bpy)₃Cl₂ was successfully incorporated into the silica sol-gel film. It was found that many irregular Ru(bpy)₃Cl₂/sol-gel clusters were formed on surfaces through one deposition and thick sol-gel films were observed after further deposition. Electrochemical properties and electrochemiluminescence (ECL) behaviors of Ru(bpy)₃Cl₂/sol-gel films could be easily adjusted by deposition numbers and time. At last, the Ru(bpy)₃Cl₂/sol-gel film modified electrode was used for solid-state ECL detection of tripropylamine. The linear range was from 5.8 × 10⁻⁸ to 2.4 × 10⁻⁴ M with the detection limit of 5 nM, which was three orders of magnitude lower than that from pure Nafion-modified electrodes. The ECL sensor also exhibited high stability, and still remained 92% response after being stored in air for 35 days. This method for immobilization of Ru(bpy)₃Cl₂ is simple, convenient and low-cost relative to others, so it shows promising applications in solid-state ECL detection.     

Thermodynamic representation of the NaCl + Na2SO4 + H2O system with electrolyte NRTL model

A comprehensive thermodynamic model based on the electrolyte NRTL (eNRTL) activity coefficient equation is developed for the NaCl + H₂O binary, the Na₂SO₄ + H₂O binary and the NaCl + Na₂SO₄ + H₂O ternary. The NRTL binary parameters for pairs H₂O-(Na⁺, Cl⁻) and H₂O-(Na⁺, SO₄²⁻), and the aqueous phase infinite dilution heat capacity parameters for ions Cl⁻ and SO₄²⁻ are regressed from fitting experimental data on mean ionic activity coefficient, heat capacity, liquid enthalpy and dissolution enthalpy for the NaCl + H₂O binary and the Na₂SO₄ + H₂O binary with electrolyte concentrations up to saturation and temperature up to 473.15 K. The Gibbs energy of formation, enthalpy of formation and heat capacity parameters for solids NaCl_(s), NaCl·2H₂O_(s), Na₂SO_4(s) and Na₂SO₄·10H₂O_(s) are obtained by fitting experimental data on solubilities of NaCl and Na₂SO₄ in water. The NRTL binary parameters for the (Na⁺, Cl⁻)-(Na⁺, SO₄²⁻) pair are regressed from fitting experimental data on dissolution enthalpies and solubilities for the NaCl + Na₂SO₄ + H₂O ternary.     

Determination of water-soluble inorganic and organic species in atmospheric fine particulate matter

The use of ion chromatography (IC) in conjunction with ultrasonic extraction is described for the routine analysis of water-soluble major inorganic ions and organic acids in atmospheric fine particles (PM_2.5). Both the extraction method and the IC analysis were validated using NIST SRM 1648 (urban particulate matter). In addition, the reliability of the IC method was established by intercomparison of results obtained with those from suitable alternative analytical techniques (atomic absorption spectrometry (AAS), proton-induced X-ray emission (PIXE) spectrometry, and UV-Visible spectrophotometry). The validated IC method was successfully applied for field monitoring of PM_2.5 particles collected in Singapore over an extended period of time. The IC analysis revealed that the concentrations of individual ions were in the order, SO₄²⁻ > NH₄⁺ > NO₃⁻ > Na⁺ > K⁺ > Cl⁻, respectively. Among the major ionic components, SO₄²⁻ contributed 50% to the measured water-soluble aerosol mass followed by NH₄⁺ (16.5%) and NO₃⁻ (9.0%). The cations Na⁺, K⁺, Mg²⁺, and Ca²⁺ accounted for 24% of the total water-soluble mass. The IC analysis was performed to quantify the organic acids, which typically account for a small fraction of water-soluble organic compounds in PM_2.5. Oxalate was found to be the dominant species among the organic acids measured in this work.     

Infrared spectroscopy of SO2 clusters in rare gas matrices revisited: Assignment of species in Ar matrix

We have observed infrared spectra of the SO₂ clusters in rare gas matrices (Ar, Kr, Xe). The spectral dependence on temperature and concentration led us to the firm assignment of the SO₂ dimer in Kr and Xe, the result of which was used to reassign dimeric vibrational transitions in Ar that have been controversial for more than ten years.     

A new generation of cyanide ion-selective membranes for flow injection application: part II. Comparative study of cyanide flow-injection detectors based on thin electroplated silver chalcogenide membranes

Using induced cathodic electrodeposition a number of silver chalcogenide thin layer membranes of non-trivial composition have been synthesized and their performance as ion-selective flow-injection potentiometric detectors (FIPDs) for free cyanide has been critically estimated in the context of the stringent requirements for toxic cyanide environmental monitoring. AgSCN/Ag₂S, Ag₂S, Ag_2+δSe, Ag_2+δSe_1−xTe_x (0 < δ < 0.25 and x ≈ 0.13), Ag₂Se and Ag₂Se_1−xTe_x electroplated membranes were selected for the present performance-based comparative study in order to obtain a feedback information about the effect of membrane composition. Both silver selenide and Te-doped silver selenide membranes, irrespective of their stoichiometry with respect to silver, exhibit the lowest detection limit for CN⁻ (52 ppb) with linear double-Nernstian response down to 130 ppb. The type of chalcogene anion in the membrane composition proves to exert dominant effect on the general performance characteristics of the newly developed FIPDs. The silver stoichiometry (intrinsic defects factor) and the inclusion of Te-dopant (extrinsic defects factor) have more pronounced effect on the profile of the output signal and exert moderate control on the detectors selectivity and baseline stability. This new generation of CN⁻—ion-selective membranes for FIPDs exhibits high selectivity against the common interferents present in cyanide effluents such as SCN⁻, S₂O₃²⁻, Cl⁻ and do not get poisoned in the presence of S²⁻. Moreover, their long-term stability and signal reproducibility, which make redundant the regular day-to-day calibration, coupled with the cost-effective technology for membranes preparation and easy re-generation make them attractive candidates for incorporation into automated in-field devices for in situ cyanide toxic species monitoring.     

A monitor for atmospheric sulphur dioxide,based on enrichment of SO2 by a polydispersive water aerosol

A monitor for continuous analysis of sulphur dioxide in the atmosphere at the ppb v/v level (1 ppb v/v = 2.62 g/m³ SO₂) is described. The apparatus operates on the principle of equilibrium accumulation of sulphur dioxide from the air by a polydispersive water aerosol which continuously transfers SO₂ from an air-flow of l/min into microlitre volumes of water condensate. High sensitivity (1 ppb v/v), low relative error (± 5% at 4 ppb v/v SO₂), high selectivity (CO₂ does not interfere at a concentration of 2 × 10³ ppm v/v, interference by NO _x and H₂S is acceptably low), and low response delay (10 s) are provided by a compact coupling of the enrichment procedure with conductivity detection of SO₂ in the film of water aerosol condensate formed directly on the wire-gauze sensor. The reliability of the method has been studied under simulated conditions, with spectrophotometric method as reference. The analyser is computer-controlled, and the detector response is processed on-line and displayed (as g/m³) in real-time on a screen or is transmitted telemetrically to a control centre. It is portable and suitable for use in both stationary and moving locations.The paper is dedicated to the 65th anniversary of the birthday of Prof. Josef F. K. Huber     

Advantages of the Ns group in the reactions of N-SO2R inosines with benzylamine and with NH3

The reactivity of N¹-alkylsulfonyl- and N¹-arylsulfonyl-2′,3′,5′-tri-O-acetylinosine with benzylamine and with ¹⁵NH₃, regarding the attack on C2, has been shown to be in the order CF₃SO₂ (Tf) > 2,4-(NO₂)₂C₆H₃SO₂ (DNs) ? 4-NO₂C₆H₄SO₂ (pNs) ≈ C₆F₅SO₂ (PFBs) > 2-NO₂C₆H₄SO₂ (Ns) ? CH₃SO₂ (Ms) > 4-CH₃C₆H₄SO₂ (Ts) > 2,4,6-(CH₃)₃C₆H₂SO₂ (Mts). In spite of its intermediate reactivity, the Ns group is the most appropriate, since in this case the formation of by-products is minimised during the ring-opening and ring-closing steps of the process. Another advantage of the Ns group is thus disclosed.     

Carbon nanotube networks as gas sensors for NO2 detection

Networks of different carbon nanotube (CNT) materials were investigated as resistive gas sensors for NO₂ detection. Sensor films were fabricated by airbrushing dispersions of double-walled and multi-walled CNTs (DWNTs and MWNTs, respectively) on alumina substrates. Sensors were characterized by resistance measurements from 25 to 250 °C in air atmosphere in order to find the optimum detection temperature. Our results indicate that CNT networks were sensitive to NO₂ concentrations as low as 0.1 ppm. All tested sensors provided significantly lower response to interfering gases such as H₂, NH₃, toluene and octane. We demonstrate that the measured sensitivity upon exposure to NO₂ strongly depends on the employed CNT material. The highest sensitivity values were obtained at temperatures ranging between 100 and 200 °C. The best sensor performance, in terms of recovery time, was however achieved at 250 °C. Issues related to the gas detection mechanisms, as well as to CNT network thermal stability in detection experiments performed in air at high operation temperatures are also discussed.     

Flux syntheses of La-doped NaTaO3 and its photocatalytic activity

The La-doped (2%) NaTaO₃ perovskite-type solid was synthesized in high purity and homogeneity within a molten Na₂SO₄/K₂SO₄ (1:1 molar ratio) flux in much shortened reaction times, 0.5-1.0 h, compared to conventional solid-state techniques. The particle morphologies were investigated by scanning electron microscopy and were irregular block-shaped with dimensions of 500-100 nm and smaller surface features. The bulk particle sizes were found to decrease with increasing amounts of flux used in the synthesis, from 1:1 (NaTaO₃:flux), 1:2 to 1:3 for a reaction duration of 1 h. Photocatalytic activities of the NaTaO₃ products were measured in an aqueous methanol solution to be 535-1115 μmol H₂ h⁻¹ g⁻¹, and which increased with increasing particle sizes and decreasing amounts of flux used in the synthesis. These rates were up to ×2 greater than that measured for a conventionally prepared La-doped (2%) NaTaO₃ sample, which is currently one of the most efficient UV-photocatalysts known.     

Application of copper sulfate pentahydrate as an ammonia removal reagent for the determination of trace impurities in ammonia by gas chromatography

Rapid analysis of trace permanent gas impurities in high purity ammonia gas for the microelectronics industry is described, using a gas chromatograph equipped with a phtoionization detector. Our system incorporates a reactive precolumn in combination with the analytical column to remove the ammonia matrix peak that otherwise would complicate the measurements due to baseline fluctuations and loss of analytes. The performance of 21 precolumn candidate materials was evaluated. Copper sulfate pentahydrate (CuSO₄·5H₂O) was shown to selectively react with ammonia at room temperature and atmospheric column pressures, without affecting the hydrogen, oxygen, nitrogen, methane or carbon monoxide peak areas. To prevent loss of trace carbon dioxide, an additional boron trioxide reactant layer was inserted above the copper sulfate pentahydrate bed in the reactive precolumn. Using the combined materials, calibration curves for carbon dioxide proved to be equivalent in both ammonia and helium matrix gases. These curves were equivalent in both matrix gases. The quantitative performance of the system was also evaluated. Peak repeatabilities, based on eight injections, were in the range of 4.1–8.2% relative standard deviation; and detection limits were 6.9 ppb for H₂, 1.8 ppb for O₂, 1.6 ppb for N₂, 6.4 ppb for CH₄, 13 ppb for CO, and 5.4 ppb for CO₂.     

Effect of surface fluorination and conductive additives on the electrochemical behavior of lithium titanate (Li4/3Ti5/3O4) for lithium ion battery

Effect of surface fluorination and conductive additives on the charge/discharge behavior of lithium titanate (Li_4/3Ti_5/3O₄) has been investigated using F₂ gas and vapor grown carbon fiber (VGCF). Surface fluorination of Li_4/3Ti_5/3O₄ was made using F₂ gas (3 × 10⁴ Pa) at 25-150 °C for 2 min. Charge capacities of Li_4/3Ti_5/3O₄ samples fluorinated at 70 °C and 100 °C were larger than those for original sample at high current densities of 300 and 600 mA/g. Optimum fluorination temperatures of Li_4/3Ti_5/3O₄ were 70 °C and 100 °C. Fibrous VGCF with a large surface area (17.7 m²/g) increased the utilization of available capacity of Li_4/3Ti_5/3O₄ probably because it provided the better electrical contact than acetylene black (AB) between Li_4/3Ti_5/3O₄ particles and nickel current collector.     

Tunable separation of anions and cations by column switching in ion chromatography

A convenient ion chromatography method has been proposed for the routine and simple determination of anions (Cl⁻, SO₄²⁻ and NO₃⁻) and/or cations (Na⁺, NH₄⁺, K⁺, Mg²⁺ and Ca²⁺) using a single pump, a single eluent and a single detector. The present system used cation-exchange and anion-exchange columns connected in series via two 6-port switching valves or a single 10-port valve. The connection order of the ion-exchange columns could be varied by switching the valve(s). The present system therefore allowed the separation of either cations or anions in a single chromatographic run. While one ion-exchange column is being operated, the other ion-exchange column is being conditioned, i.e., the columns are always ready for analysis at any time. When 2.4 mM 5-sulfosalicylic acid was used as the eluent, the three anions and the five cations could be separated on the anion-exchange column and cation-exchange column, respectively. In order to obtain the separations of the target ions, the injection valve was placed between the two columns. Complete separations of the above anions or cations were demonstrated within 10 min each. The detection limits at S/N = 3 were 19-50 ppb (μg/l) for cations and 10-14 ppb for anions. The relative standard deviations of the analyte ions were less than 1.1, 2.9 and 2.8% for retention time, peak area and peak height, respectively. This proposed technique was applied to the determination of common anions and cations in river water samples.     

Zirconium-catalyzed methylalumination of heterosubstituted arylethynes: Factors affecting the regio-, stereo-, and chemoselectivities

The Zr-catalyzed methylalumination of heterosubstituted arylethynes containing O, S, Cl, and Si can proceed in high yields (>70%) and in a highly regio- and stereoselective manner (?98-99%), although SO₂Ph, Br, and Cl in a benzylic position present serious chemoselectivity-related problems. The low regioselectivity of 60% initially observed with o-ethynylphenol (1a) has been elevated to ?98% through the use of either a catalytic amount of Zr(ebi)Cl₂ or Zr(2-Me-Ind)₂Cl₂ or, more conveniently, the stoichiometric amount of ZrCp₂Cl₂, ZrCp₂MeCl, or ZrCp₂Me₂ in conjunction with the use of a deficient amount (0.9 molar equiv.) of I₂ for subsequent iodinolysis.     

Ab initio and density functional theory study of the enthalpies of formation of F2SOx and FClSOx (x=1, 2)

Enthalpies of formation of F₂SO, F₂SO₂, FClSO and FClSO₂ molecules have been determined using ab initio molecular orbital theory and density functional theory (DFT) calculations. Different DFT approaches and levels of the Gaussian-3 and the complete basis set (CBS) ab initio model chemistries have been employed to calculate enthalpies of formation from both total atomization energies and isodesmic reaction schemes. The best values at 298 K for F₂SO, F₂SO₂, FClSO and FClSO₂ as derived from an average of G3, G3B3, CBS-Q and CBS-QB3 isodesmic energies are −140.6, −181.1, −92.6 and −132.3 kcal mol⁻¹, respectively. The results obtained suggest that the accumulated small component errors found in the DFT-based methods are significantly reduced at the ab initio levels employed. Structural properties, harmonic vibrational frequencies, mode assignations and infrared intensities derived from B3LYP and mPW1PW91 functional with the 6-311+G(3df) basis set are presented.     

Palladium-catalyzed cross-coupling reaction of alkynylzincs with benzylic electrophiles

The reaction of alkynylzinc bromides with benzyl bromides or chlorides in the presence of a catalytic amount of Pd(DPEphos)Cl₂ in THF at 23 °C cleanly produces the corresponding benzylated alkynes in 73-97% yields. With 10⁻³ mol % of Pd(DPEphos)Cl₂, the maximum turnover number of 7.1 × 10⁴ has been observed for the formation of PhCCCH₂Ph.     

Sol-gel synthesis of mesoporous CaCu3Ti4O12 thin films and their gas sensing response

A new sol-gel synthesis procedure of stable calcium copper titanate (CaCu₃Ti₄O₁₂—CCTO) precursor sols for the fabrication of porous films was developed. The composition of the sol was selected in order to avoid the precipitation of undesired phases; ethanol was used as solvent, acetic acid as modifier and poly(ethyleneglycol) as a linker agent. Films deposited by spin-coating onto oxidized silicon substrates were annealed at 700 °C. The main phase present in the samples, as detected by X-ray diffraction and Raman spectroscopy, was CaCu₃Ti₄O₁₂. Scanning electron microscopy analysis showed that mesoporous structures, with thicknesses between 200 and 400 nm, were developed as a result of the processing conditions. The films were tested regarding their sensibility towards oxygen and nitrogen at atmospheric pressure using working temperatures from 200 to 290 °C. The samples exhibited n-type conductivity, high sensitivity and short response times. These characteristics indicate that CCTO mesoporous structures obtained by sol-gel are suitable for application in gas sensing.