Characterization of an electrochemical mercury sensor using alternating current,cyclic, square wave and differential pulse voltammetry

Here we report the characterization of an electrochemical mercury (Hg²⁺) sensor constructed with a methylene blue (MB)-modified and thymine-containing linear DNA probe. Similar to the linear probe electrochemical DNA sensor, the resultant sensor behaved as a “signal-off” sensor in alternating current voltammetry and cyclic voltammetry. However, depending on the applied frequency or pulse width, the sensor can behave as either a “signal-off” or “signal-on” sensor in square wave voltammetry (SWV) and differential pulse voltammetry (DPV). In SWV, the sensor showed “signal-on” behavior at low frequencies and “signal-off” behavior at high frequencies. In DPV, the sensor showed “signal-off” behavior at short pulse widths and “signal-on” behavior at long pulse widths. Independent of the sensor interrogation technique, the limit of detection was found to be 10 nM, with a linear dynamic range between 10 nM and 500 nM. In addition, the sensor responded to Hg²⁺ rather rapidly; majority of the signal change occurred in <20 min. Overall, the sensor retains all the characteristics of this class of sensors; it is reagentless, reusable, sensitive, specific and selective. This study also highlights the feasibility of using a MB-modified probe for real-time sensing of Hg²⁺, which has not been previously reported. More importantly, the observed “switching” behavior in SWV and DPV is potentially generalizable and should be applicable to most sensors in this class of dynamics-based electrochemical biosensors.     

A new chemiluminescence probe for singlet oxygen based on tetrathiafulvalene-anthracene dyad capable of performing detection in water/alcohol solution

A new tetrathiafulvalene-anthracene dyad 1 with two “tetraethylene glycol” units was synthesized and characterized. Strong chemiluminescence was observed upon reaction of dyad 1 with singlet oxygen (¹O₂), and this reaction shows fairly good selectivity toward ¹O₂ over other reactive oxygen species. Due to the introduction of two hydrophilic “tetraethylene glycol” units, the detection of ¹O₂ with dyad 1 can be performed in alcohol/water solution, which is relatively a mild medium when compared with water/tetrahydrofuran solution required by other tetrathiafulvalene-anthracene dyads. Dyad 1 may have a wider use for detection of ¹O₂ in biological systems.     

An ultrasensitive chemiluminescence immunosensor for PSA based on the enzyme encapsulated liposome

A highly sensitive chemiluminescence immunosensor for the detection of prostate-specific antigen (PSA) was developed based on a novel amplification procedure with the application of enzyme encapsulated liposome. Horseradish peroxidase (HRP) encapsulated and antibody-modified liposome acts as the carrier of a large number of markers and specific recognition label for the amplified detection of PSA. In the detection of PSA, the analyte was first bound to the specific capture antibody immobilized on the microwell plates, and then sandwiched by the antibody-modified liposomes encapsulating HRP. The encapsulated markers, HRP molecules were released by the lysis of the specifically bound liposomes in the microwell with Triton X-100 solution. Then, the analyte PSA could be determined via the chemiluminescence signal of HRP-catalyzed luminol/peroxide/enhancer system. The “sandwich-type” immunoassay provides the amplification route for the PSA detection in ultratrace levels. The CL emission intensity exhibits dynamic correlation to PSA concentration in the range from 0.74 pg/ml to 0.74 μg/ml with readily achievable detection limit of 0.7 pg/ml.     

An aptameric molecular beacon-based “Signal-on” approach for rapid determination of rHuEPO-α

The aim of this work is to describe the first example of aptameric molecular beacon (MB)-based probe for the detection of recombinant human erythropoietin (rHuEPO-α) in physiological buffer, using a novel 35 nt ssDNA aptamer (807-35 nt) originally isolated by Systematic Evolution of Ligands by Exponential enrichment (SELEX) technique in our laboratory. Both “Signal-on” and “Signal-off” MB modes were developed, respectively, in which the conformational alteration of aptamer before and after binding to rHuEPO-α can be demonstrated in terms of the correspondingly fluorescent changes. Comparing with “Signal-off” mode, “Signal-on” mode provided higher sensitivity, while with the addition of target rHuEPO-α, quenching between fluorescent 807-35 nt aptamer (F-Apt) and a short quencher-labeled complementary sequence (QDNA) was disturbed by the specific binding between rHuEPO-α and F-Apt. QDNA was thus loosened and released from F-Apt, leading to a consequently full fluorescent restoration. Systematic optimization of parameters in “Signal-on” mode were carried out, the choice of QDNA length, the hybridization site of a small supplementary DNA (SDNA) stabilizer, and the existence of Mg²⁺ cation played essential roles for the performance characterization. A convenient and sensitive determination of rHuEPO-α with a LOD of 0.4 nM was achieved.     

Integrated microfluidic devices

“With the fundamentals of microscale flow and species transport well developed, the recent trend in microfluidics has been to work towards the development of integrated devices which incorporate multiple fluidic, electronic and mechanical components or chemical processes onto a single chip sized substrate. Along with this has been a major push towards portability and therefore a decreased reliance on external infrastructure (such as detection sensors, heaters or voltage sources).” In this review we provide an in-depth look at the “state-of-the-art” in integrated microfludic devices for a broad range of application areas from on-chip DNA analysis, immunoassays and cytometry to advances in integrated detection technologies for and miniaturized fuel processing devices. In each area a few representative devices are examined with the intent of introducing the operating procedure, construction materials and manufacturing technique, as well as any unique and interesting features.     

Near-infrared spectroscopy applications in pharmaceutical analysis

Near-infrared (NIR) spectroscopy is a fast and non-destructive analytical technique that offers many advantages for a broad range of industrial applications. In this work, we reviewed recent developments in the pharmaceutical domain where it can be applied from raw material identification to final product release. The characteristics of NIR allow the technique to be implemented as a process analytical technology (PAT). Moreover, recent instrumental developments open the perspectives of numerous applications in the NIR imaging area. After “Introduction”, according to their subject, the applications are discussed in the parts “Identification”, “Water content”, “Assay” and “Other applications”.     

Highly selective in situ metal ion determination by hybrid electrochemical "adsorption-desorption" and colorimetric methods

A novel and facile hybrid analytical method coupling electrochemical “adsorption–desorption” and colorimetric analyses was developed to detect heavy metal ions in turbid water samples. The target metal ions were deposited onto an electrode inserted into the original sample, which was referred to as the “adsorption” process. After changing the medium, the concentrated target metal ions were dissolved in a new, clean buffer (blank buffer), which was referred to as the “desorption” process. The concentrations of the target metal ions were measured by colorimetric analyses after the addition of specific indicator amounts. We demonstrated the applicability of this method by detecting Cd²⁺, Pb²⁺ and Cu²⁺ with co-depositing Bi³⁺ on portable screen-printed electrodes (SPEs). A good correlation (correlation coefficient of R = 0.997) was observed between concentrations ranging from 1 to 200 μM and absorbance values. After the multiple “desorption” process, the even better detection limits as low as 10, 10 and 100 nM were achieved for Cd²⁺, Pb²⁺ and Cu²⁺, respectively. The practicality of this hybrid method was confirmed by the detection of Cd²⁺, Pb²⁺ and Cu²⁺ in wastewater samples, and these results were in agreement with inductively coupled plasma atomic emission spectroscopy (ICP-AES). Overall, this hybrid method provides a simple, selective and effective technique for environmental pollutant analyses.     

Chemiluminescence as a condition monitoring method for thermal aging and lifetime prediction of an HTPB elastomer

Chemiluminescence (CL) has been applied as a condition monitoring technique to assess aging related changes in a hydroxyl-terminated-polybutadiene based polyurethane elastomer. Initial thermal aging of this polymer was conducted between 110 and 50 °C. Two CL methods were applied to examine the degradative changes that had occurred in these aged samples: isothermal “wear-out” experiments under oxygen yielding initial CL intensity and “wear-out” time data, and temperature ramp experiments under inert conditions as a measure of previously accumulated hydroperoxides or other reactive species. The sensitivities of these CL features to prior aging exposure of the polymer were evaluated on the basis of qualifying this method as a quick screening technique for quantification of degradation levels. Both the techniques yielded data representing the aging trends in this material via correlation with mechanical property changes. Initial CL rates from the isothermal experiments are the most sensitive and suitable approach for documenting material changes during the early part of thermal aging.     

An exonuclease-assisted amplification electrochemical aptasensor of thrombin coupling “signal on/off” strategy

In this work, a dual-signaling electrochemical aptasensor based on exonuclease-catalyzed target recycling was developed for thrombin detection. The proposed aptasensor coupled “signal-on” and “signal-off” strategies. As to the construction of the aptasensor, ferrocene (Fc) labeled thrombin binding aptamer (TBA) could perfectly hybridize with the methylene blue (MB) modified thiolated capture DNA to form double-stranded structure, hence emerged two different electrochemical signals. In the presence of thrombin, TBA could form a G-quadruplex structure with thrombin, leading to the dissociation of TBA from the duplex DNA and capture DNA formed hairpin structure. Exonuclease could selectively digest single-stranded TBA in G-quadruplex structure and released thrombin to realize target recycling. As a consequence, the electrochemical signal of MB enhanced significantly, which realized “signal on” strategy, meanwhile, the deoxidization peak current of Fc decreased distinctly, which realized “signal off” strategy. The employment of exonuclease and superposition of two signals significantly improved the sensitivity of the aptasensor. In this way, an aptasensor with high sensitivity, good stability and selectivity for quantitative detection of thrombin was constructed, which exhibited a good linear range from 5 pM to 50 nM with a detection limit of 0.9 pM (defined as S/N = 3). In addition, this design strategy could be applied to the detection of other proteins and small molecules.     

Synthesis and physico-chemical characterization of Au/TiO2 nanostructures formed by novel “cold” and “hot” nanosoldering of Au and TiO2 nanoparticles dispersed in water

A novel approach to synthesize Au/TiO₂ nanostructures with interesting optical properties is presented and discussed. It is based on the nanoparticle “cold” or “hot” nanosoldering occurring when two water suspensions of Au and TiO₂ nanoparticles are merely mixed at room temperature or laser irradiated after mixing.Thanks to the high fraction and mutual reactivity of surface species, immediately after the mixing process, the encounters between Au and TiO₂ nanoparticles in liquid phase are enough for “cold” nanosoldering of gold nanoparticles onto TiO₂ nanoparticles to occur. The optical characterizations show that this fast process (timescale less than 1 min) is followed by a slower process, attributable to some change of the Au nanoparticles. This latter process is significantly accelerated by the 532 nm laser light illumination. The structural and optical properties of “cold” and “hot” nanosoldered Au-TiO₂ nanoparticles were investigated by TEM, UV-vis and fluorescence spectroscopies.Interesting optical limiting response was detected at laser fluences above 0.8 J/cm². The nature of the nonlinear effect was investigated by the Z-scan technique, determining both the nonlinear absorption coefficient and the refraction index. Such interesting non-linear optical properties are worth to be tailored for specific applications.     

Fabricating a reversible and regenerable electrochemical biosensor for quantitative detection of antibody by using “triplex-stem” DNA molecular switch

A reversible and regenerable electrochemical biosensor is fabricated for quantitative detection of antibody based on “triplex-stem” molecular switches. A hairpin-shaped oligonucleotide (hairpin DNA) labeled with ferrocene (Fc) at the 3′-end is fixed on the gold electrode serving as a signal transduction probe. Its hairpin structure leads Fc close to the surface of gold electrode and produces a strong current signal (on-state). A single-strand oligonucleotide modified with two digoxin molecules on the two arm segments (capture DNA) interact with hairpin DNA with the help of Ag⁺ ions. The “triplex-stem” DNA forms, which separates Fc from the electrode and reduces the electrochemical signal (off-state). Binding of digoxin antibody to digoxin releases capture DNA from the hairpin DNA, creating an effective “off-on” current signal switch. The stability of the “triplex-stem” structure of hairpin/capture DNA is critical to the signal switch and the sensitivity of the method, which can be adjusted conveniently and efficiently by changing Ag⁺ concentrations. Based on the “off-on” current signal switch, this biosensor is used to detect digoxin antibody sensitively in blood serum. The linear range is 1.0–500 pg with a correlation coefficient of 0.996, and the detection limit is 0.4 pg. Also, this biosensor shows excellent reversibility and reproducibility, which are significant requirements for practical biosensor applications.     

High sensitive and label-free colorimetric DNA detection based on nicking endonuclease-assisted activation of DNAzymes

Horseradish peroxidase mimicking DNAzyme (HRP-DNAzyme) attracts growing interest as an amplifying label for biorecognition and biosensing events, especially for DNA detection. However, in the traditional designs, one target molecule can only generate one HRP-DNAzyme, which limits the signal enhancement and thus its sensitivity. In this article, we propose an amplified and label-free colorimetric DNA detection strategy based on nicking endonuclease (NEase)-assisted activation of HRP-DNAzymes (NEAA-DNAzymes). This new strategy relies on the hairpin-DNAzyme probe and NEase-assisted target recycling. In the hairpin-DNAzyme probe, the HRP-DNAzyme sequence is protected in a “caged” inactive structure, whereas the loop region includes the target complementary sequence. Upon hybridization with target, the beacon is opened, resulting in the activation of the HRP-DNAzyme. Meanwhile, upon formation of the duplex, the NEase recognizes a specific nucleotide sequence and cleaves the hairpin-DNAzyme probe into two fragments. After nicking, the fragments of the hairpin-DNAzyme probe spontaneously dissociate from the target DNA. Amplification is accomplished by another hairpin-DNAzyme probe hybridizing to the released intact target to continue the strand-scission cycle, which results in activation of numerous DNAzymes. The activated HRP-DNAzymes generate colorimetric or chemiluminescence readout signals, thus providing the amplified detection of DNA. The detection limit of the colorimetric method is 10 pmol/L, which are three orders of magnitude lower than that without NEase. In addition, the detection limit of the chemiluminescence method is 0.2 pmol/L. Meanwhile, this strategy also exhibits high discrimination ability even against single-base mismatch.     

The economics of residue analysis

Since the onset of residue analysis some 40 years ago, much attention has been paid to several analytical aspects [e.g., the fight to achieve lower limits of detection (LODs), the gain in specificity, and quality assurance]. In recent years, “omic approaches” have also been introduced to accomplish these purposes. However, when reviewing the literature, one “omic” of residue analysis is not represented: the economic.Residue analysis covers a broad working area, including banned (group A) substances and registered veterinary drugs (group B). Some 40 years ago, only thin-layer chromatography and gas chromatography with electron-capture detection were used for A substances, in combination with laborious sample clean-up and thus small sample throughput. The nominal or money price of such an analysis remained relatively stable from 1970 to 2010. However, the operational costs of analysis increased considerably over the years, in particular, personnel and equipment costs. But, higher operational costs were countered by much greater sample throughput, although this phenomenon remains limited.For B substances, the strategy of screening with microbiological inhibition tests at a very low price competes with sophisticated ultra-high-performance liquid chromatography with (high-resolution) mass spectrometry systems, where the number of analytes/run can theoretically reach 122,500.The question that we address in this contribution from an economics point of view is: “How do laboratories keep the balance between price of analysis, specificity, LOD, number of analytes, quantification and quality assurance?”     

Label-free genotyping of cytochrome P450 2D6*10 using ligation-mediated strand displacement amplification with DNAzyme-based chemiluminescence detection

Genotyping of cytochrome P450 monooxygenase 2D6*10 (CYP2D6*10) plays an important role in pharmacogenomics, especially in clinical drug therapy of Asian populations. This work reported a novel label-free technique for genotyping of CYP2D6*10 based on ligation-mediated strand displacement amplification (SDA) with DNAzyme-based chemiluminescence detection. Discrimination of single-base mismatch is firstly accomplished using DNA ligase to generate a ligation product. The ligated product then initiates a SDA reaction to produce aptamer sequences against hemin, which can be probed by chemiluminescence detection. The proposed strategy is used for the assay of CYP2D6*10 target and the genomic DNA. The results reveal that the proposed technique displays chemiluminescence responses in linear correlation to the concentrations of DNA target within the range from 1 pM to 1 nM. A detection limit of 0.1 pM and a signal-to-background ratio of 57 are achieved. Besides such high sensitivity, the proposed CYP2D6*10 genotyping strategy also offers superb selectivity, great robustness, low cost and simplified operations due to its label-free, homogeneous, and chemiluminescence-based detection format. These advantages suggest this technique may hold considerable potential for clinical CYP2D6*10 genotyping and association studies.     

The effects of annealing in inert atmospheres and of oxygen concentration on chemiluminescence from polypropylene

It has been shown that heating polypropylene powder under a nitrogen atmosphere leads to the significant prolongation of the oxidation induction time measured by chemiluminescence in oxygen at 130 and 140 °C. While heating in nitrogen from 0 to 4 h at 140 °C leads to the linear increase of oxidation induction time, the maximum chemiluminescence intensity I_stat increases with the time of sample annealing until 2 h; then it starts to decay. The different and sometime unknown thermal history of the sample may thus explain the scatter of induction times of oxidation observed with different PPs whether they be pure or stabilised. Maximum chemiluminescence intensity plotted vs. concentration of oxygen in the surrounding atmosphere at 130 and 140 °C also increases linearly; however, this does not correspond with very small reduction of oxidation induction time. The four-parametric “master equations” used in our earlier papers were applied to fit the chemiluminescence runs both in oxygen and in nitrogen. The equation operates with the rate constants of hydroperoxide decomposition and oxidation spreading but at the same time, it takes into account the possible effect of oxidation products on decomposition of hydroperoxides.     

Gold immunochromatographic strips for enhanced detection of Avian influenza and Newcastle disease viruses

A new technique that uses gold immunochromatographic strips enhances the detection sensitivity by inducing the clustering of additional gold nanoparticles (AuNPs) around the immunogold particles immobilized on nitrocellulose strips. The additional AuNPs provide an intense signal that can be detected by the naked eye. The AuNPs were synthesized and conjugated to monoclonal antibodies using self-assembly. Other antibodies were immobilized in a defined detection zone on the nitrocellulose membrane. The detection principle is based on a “sandwich” immunoreaction, where gold-labeled antibodies serve as signal vehicles. To improve the sensitivity of the strips, we use a mixture of 1% HAuCl₄ and 10 mmol L⁻¹ NH₂OH·HCl to “enlarge” the gold nanoparticles. The detecting limits of Avian influenza virus (AIV) and Newcastle disease virus (NDV) are significantly increased. Compared with commercial test strips, this method is 100-fold more sensitive. This method is easy to perform and can be carried out on-site in test laboratories.     

Aptamer/quantum dot-based simultaneous electrochemical detection of multiple small molecules

A novel strategy for “signal on” and sensitive one-spot simultaneous detection of multiple small molecular analytes based on electrochemically encoded barcode quantum dot (QD) tags is described. The target analytes, adenosine triphosphate (ATP) and cocaine, respectively, are sandwiched between the corresponding set of surface-immobilized primary binding aptamers and the secondary binding aptamer/QD bioconjugates. The captured QDs yield distinct electrochemical signatures after acid dissolution, whose position and size reflect the identity and level, respectively, of the corresponding target analytes. Due to the inherent amplification feature of the QD labels and the “signal on” detection scheme, as well as the sensitive monitoring of the metal ions released upon acid dissolution of the QD labels, low detection limits of 30 nM and 50 nM were obtained for ATP and cocaine, respectively, in our assays. Our multi-analyte sensing system also shows high specificity to target analytes and promising applicability to complex sample matrix, which makes the proposed assay protocol an attractive route for screening of small molecules in clinical diagnosis.     

An electronic tongue for gliadins semi-quantitative detection in foodstuffs

An all-solid-state potentiometric electronic tongue with 36 polymeric membranes has been used for the first time to detect gliadins, which are primarily responsible for gluten intolerance in people suffering from celiac disease. A linear discriminant model, based on the signals of 11 polymeric membranes, selected from the 36 above using a stepwise procedure, was used to semi-quantitatively classify samples of a “Gluten-free” foodstuff (baby milked flour), previously contaminated with known amounts of gliadins (<10, 20-50 or >50 mg/kg), as “Gluten-free”, “Low-Gluten content” or “Gluten-containing”. For this food matrix, the device had sensitivity towards gliadins of 1-2 mg/kg and overall sensitivity and specificity of 77% and 78%, respectively. Moreover, the device never identified an ethanolic extract containing gliadins as “Gluten-free”. Finally, the system also allowed distinguishing “Gluten-free” and “Gluten-containing” foodstuffs (15 foods, including breads, flours, baby milked flours, cookies and breakfast cereals) with an overall sensitivity and specificity greater than 83%, using the signals of only 4 selected polymeric membranes (selected using a stepwise procedure). Since only one “Gluten-containing” foodstuff was misclassified as “Gluten-free”, the device could be used as a preliminary tool for quality control of foods for celiac patients.     

Improved compatibility of liquid chromatography with electrospray tandem mass spectrometry for tracing occurrence of barbital homologous residues in animal tissues

This work describes a liquid chromatography–tandem mass spectrometry (LC–MS/MS) procedure for multiplex screening, ultratrace quantification and reliable confirmation of barbital series residues in animal-derived food matrices. The method is developed based on a distinct dependency of the electrospray ionization (ESI) response of nine structural homologues on LC eluent properties and gas-phase ion chemistry during the ESI process. The “wrong-way-round” negative ionization aspect has been explored to optimize the compatibility of the hyphenated LC–MS/MS technique, which facilitates detection limits at 30–100-fold lower than 0.01 ppm without derivatization or post-column basification step. A mobile phase using methanol modified with 0.01% acetic acid is adopted to achieve an approximately 2–9-fold increase in signal-to-noise ratio over the results under suboptimal conditions. There is no significant differential matrix effects or deuterium isotope effects on chromatographic retention and ESI responsiveness at all levels across the different analyte–matrix pairs. Mean recoveries ranged from 79.6% (barbital) to 108% (secobarbital) at fortified levels of 0.5–20 ng/g within relative standard deviations less than 11%. Between-run repeatability and within-laboratory reproducibility were 3–11% and 5–13%, respectively. An ion ratio criterion for valid detection limit data for simultaneous screening of homologous multiresidues in complex sample matrices is proposed. The satisfactory applicability of the newly described procedure to 43 real samples including pork, poultry meat, swine liver, fish tissue and shrimp muscle demonstrated the LC–MS/MS technique with facile sample handling can serve as an attractive alternative analytical method accepted for regulatory purpose.     

Part two: Analytical optimisation of a procedure for lead detection in milk by means of bismuth-modified screen-printed electrodes

This work reports the optimisation of a new analytical method for lead ion detection in milk; the electrochemical detection scheme is based on the method that was described in Part I [1]. It features the use of a disposable, environmentally friendly bismuth film electrode to replace the traditionally used (toxic) mercury one while here we report an arduous development of sample treatment so that the simple device can be applied as a screening tool in many settings. For this purpose, a milk pre-treatment procedure by means of wet digestion with HCl, HClO₄, and H₂O₂ combined with an ultrasonic treatment was developed. The detection of lead ions in treated milk was then carried out using a disposable screen-printed electrode modified with Nafion^® and an “in situ” bismuth film, with the analysis being performed in anodic stripping voltammetry mode. The analytical method developed allows the detection of milk contaminated with lead ions at a concentration of 20 μg Kg⁻¹ (legal limit) and it can be proposed as a screening method for routine analysis of lead ions in milk with the advantage of employing inexpensive and portable instrumentation. Moreover, dedicated software supported by a portable instrument introduces procedures that are essential to avoid distortion from ambient lead contamination and also makes it possible for an unskilled operator to carry out each step of the analysis.