Flow-injection spectrophotometric determination of cyanate in bioremediation processes by use of immobilised inducible cyanase

A new flow injection (FI) method for photometric monitoring of cyanate in bioremediation processes using immobilised native cyanase is described. The method is based on the catalytic reaction between cyanate and bicarbonate to produce ammonia and carbon dioxide in the presence of an inducible native cyanase, immobilised in a reactor packed with glass beads. Two degrees of purification of the biocatalyst were used-heated cell-free extract and purified extract of cyanase from Pseudomonas pseudoalcaligenes CECT 5344. The ammonia produced by the enzymatic reaction is finally monitored photometrically at 700 nm using a modification of the conventional Berthelot method. The method furnishes different calibration curves depending on the degree of purification of the cyanase, with linear ranges between 1.23 and 616.50 micromol L(-1) ( r(2)=0.9979, n=7) and between 1.07 and 308.25 micro mol L(-1) ( r(2)= 0.9992, n=7) for the heated cell-free extract and the purified cyanase extract, respectively. No statistically significant differences between the samples were found in the precision study evaluated at two cyanate concentration levels using one-way analysis of variance. A sampling frequency of 15 h(-1) was achieved. The method was used to monitor cyanate consumption in a cyanate bioremediation tank inoculated with Pseudomonas pseudoalcaligenes CECT 5344 strain. The correlation between cyanate degradation and ammonia production was tested using a conventional method. Finally, the method was applied to different samples collected from the bioremediation tank using the standard addition method; recoveries between 85.9 and 97.4% were obtained.     

Flow-injection determination of 3-hdroxybutyrate in serum with an immobilized 3-hydroxybutyrate dehydrogenase reactor and chemiluminescence detection

A flow-injection system for the determination of 3-hydroxybutyrate in serum is described. 3-Hydroxybutyrate dehydrogenase is immobilized on poly(vinyl alcohol) beads and incorporated in a flow-injection system. 1-Methoxy-5-methylphenazinium methylsulphate reacts with enzymatically generated NADH to give H₂O₂, which is detected chemiluminometrically with the reaction of luminol and hexacynoferrate(III). Serum is diluted and filtered through an ultrafiltration membrane. The system responds linearly to injected samples (80 μl) in the concentration range 0.5–300 μM; the detection limit is 0.1 μM. The within-day relative standard deviation (n = 90) for 58 μM 3-hydroxybutyrate in serum is 0.8%. The maximum throughout is 20 samples per hour. The immobilized enzyme is stable for at least 1 month.     

Thermal and thermo-mechanical degradation of poly(3-hydroxybutyrate)-based multiphase systems

The influence of fermentation residues and quaternary ammonium salts on the thermal and thermo-mechanical degradation of a biodegradable bacterial poly(3-hydroxybutyrate), PHB, was studied. The results obtained from DSC, SEC and TG analyses performed on blends reveal that ammonium cations greatly enhance the degradation leading to a dramatic decrease in PHB molecular weight. These results are confirmed by the thermo-mechanical study. Besides, we show that the presence of fermentation residues does not affect significantly the PHB thermal stability in comparison to the ammonium cations. A kinetic analysis based on the Coats and Redfern model was applied to the non-isothermal TGA data. This method completed by NMR characterizations led us to determine the most probable mechanism for PHB degradation in the presence of the ammonium salts. The results demonstrate that ammonium surfactants commonly found in commercial nanoclays (for nanocomposites' production) effectively have a catalytic effect on the PHB degradation.     

Flow methodology for methanol determination in biodiesel exploiting membrane-based extraction

A methodology based in flow analysis and membrane-based extraction has been applied to the determination of methanol in biodiesel samples. A hydrophilic membrane was used to perform the liquid-liquid extraction in the system with the organic sample fed to the donor side of the membrane and the methanol transfer to an aqueous acceptor buffer solution. The quantification of the methanol was then achieved in aqueous solution by the combined use of immobilised alcohol oxidase (AOD), soluble peroxidase and 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS). The optimization of parameters such as the type of membrane, the groove volume and configuration of the membrane unit, the appropriate organic solvent, sample injection volume, as well as immobilised packed AOD reactor was performed. Two dynamic analytical working ranges were achieved, up to 0.015% and up to 0.200% (m/m) methanol concentrations, just by changing the volume of acceptor aqueous solution. Detection limits of 0.0002% (m/m) and 0.007% (m/m) methanol were estimated, respectively. The decision limit (CCα) and the detection capacity (CCβ) were 0.206 and 0.211% (m/m), respectively. The developed methodology showed good precision, with a relative standard deviation (R.S.D.) <5.0% (n = 10). Biodiesel samples from different sources were then directly analyzed without any sample pre-treatment. Statistical evaluation showed good compliance, for a 95% confidence level, between the results obtained with the flow system and those furnished by the gas chromatography reference method. The proposed methodology turns out to be more environmental friendly and cost-effective than the reference method.     

Simultaneous kinetic determination of chlorpyrifos and carbaryl based on differential degradation processes in alkaline oxidative medium

A kinetic method for the simultaneous determination of chlorpyrifos and carbaryl is described. The method is based on the degradation of these compounds in alkaline hydrogen peroxide medium by measuring the absorbance at two different reaction times and at two different wavelengths. A homemade stopped-flow system coupled with a diode-array detector and the proportional equation method was used. Resolution was achieved over chlorpyrifos: carbaryl ratios ranging from 61 to 14, with relative errors of 4 and 3%, respectively. The method was successfully applied to the analysis of a commercial formulation.     

Miscibility and crystallinity of poly(3-hydroxybutyrate)/poly(3-hydroxybutyrate-co-3-hydroxyvalerate) blends

With the objective of developing new biodegradable materials, the miscibility and the crystallinity of blends of poly(3-hydroxybutyrate), P(3HB), and poly(3-hydroxybutyrate-co-3-hydroxyvalerate), P(3HB-co-3HV), have been studied. P(3HB) (300 kg mol⁻¹)/P(3HB-co-3HV)–10% 3HV (340 kg mol⁻¹) blends were prepared by casting in a wide range of proportions, and characterized by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FT-IR). The experimental values for the glass transition temperatures (T_g) are in good agreement with the values provided by the Fox equation, showing that the blends are miscible. It was observed that the T_g and the melting temperature (T_m) decreases with the increase in the P(3HB-co-3HV)–10% 3HV content, while the crystallization temperature (T_c) increases. FT-IR analyses confirmed the decrease on the crystallinity of P(3HB)/P(3HB-co-3HV)–10% 3HV blends with higher copolymer contents. Bands related to the crystallinity were changed, due to the copolymer content that produced miscible and less crystalline blends.     

Biosynthesis and biocompatibility of biodegradable poly(3-hydroxybutyrate-co-4-hydroxybutyrate)

Poly(3-hydroxybutyrate), PHB, and poly(3-hydroxybutyrate-co-4-hydroxybutyrate), P(3HB-co-4HB), consisting of 0-94% mole fraction of 4HB content, were produced in high content by Cupriavidus necator strain A-04. The carbon sources used for PHB production included sugars made locally in Thailand: refined sugarcane, brown sugarcane, rock sugar, toddy palm sugar and coconut palm sugar. The switching of the ratios of carbon to nitrogen, together with the ratios of fructose to 1,4-butanediol, were applied to P(3HB-co-4HB) production in fed-batch cultures. Optimal P(3HB-co-4HB) production was achieved with 112 g biomass and 73 g P(3HB-co-4HB) with 38% mole fraction of 4HB content. Next, P(3HB-co-4HB) with a 0, 5, 24, 38 and 64% mole fraction of 4HB content were purified and prepared as plastic films. The mechanical properties and biocompatibility of these films were tested and compared with commercial PHB, polystyrene (PS) and polyvinylchloride (PVC) prepared without additives. The results demonstrated that PHB had thermal and mechanical properties similar to those of commercial PHB. The P(3HB-co-4HB) polymers possessed melting temperature and glass transition temperature values higher than those reported previously. The mechanical properties were compared with those of PS and PVC. The in vitro biocompatibility was assessed using L929, human dermal fibroblast and Saos-2 human osteosarcoma cells. The cytotoxicity results and scanning electron micrographs showed that P(3HB-co-4HB) films have good surface characteristics and can promote cell attachment, proliferation and differentiation. Combined with their good mechanical properties, P(3HB-co-4HB) polymers possess potential usefulness for biomaterial applications in artificial skin tissue support and orthopedic support.     

Flow injection determination of histamine with a histamine dehydrogenase-based electrode

A flow injection analysis (FIA) system for the determination of histamine was developed using histamine dehydrogenase (HmDH)-based electrode. Histamine dehydrogenase was immobilized in an osmium-derivatized redox polymer, poly(1-vinylimidazole) complexed with Os(4,4′-dimethylbipyridine)₂Cl₂ (PVI-dmeOs), film on a glassy carbon electrode. As expected from the characteristics of this enzyme in a solution, this electrode exhibits high selectivity to histamine and is not sensitive to other primary amines including common biogenic amines, putrescine, cadaverine and tyramine. The detection limit for histamine was 100 pmol ( μl injection) at a S/N ratio of 3, and response linearity was retained up to 0.6 mM. The FIA system was successfully applied to the determination of histamine in fish samples. The performance of the FIA system is discussed and compared with a high-performance liquid chromatography (HPLC) method which is routinely used for histamine analysis.     

Flow injection kinetic spectrophotometric determination of trace amounts of Se(IV) in seawater

A simple, accurate, sensitive and selective flow injection catalytic kinetic spectrophotometric method for rapid determination of trace amounts of selenium is proposed in this paper. The proposed method is based on the accelerating effect of Se(IV) on the reaction of ethexlenediamine tetrecetic acid disodium salt (EDTA) and sodium nitrate with ammonium iron(II) sulfate hexahydrate in acidic media. The absorbance intensity was registered in this reaction solution at 440 nm. The calibration graph is linear in the range of 5 × 10⁻⁹-2 × 10⁻⁷ and 2 × 10⁻⁷-2 × 10⁻⁶ g ml⁻¹. The detection limit is 2 × 10⁻⁹ g ml⁻¹. The relative standard deviation was 3.4% for 5 × 10⁻⁸ g ml⁻¹ Se(IV) (n = 11), 2.7% for 5 × 10⁻⁷ g ml⁻¹ Se(IV) (n = 11). This method is very simple, rapid and suitable for automatic and continuous analysis. The presented system has been applied successfully to determination of Se(IV) of seawater samples.     

Multicommutation in flow analysis. Part 3. Spectrophotometric kinetic determination of creatinine in urine exploiting a novel zone sampling approach

Zone sampling performed on a single analytical channel and associated with the stopped-flow approach was proposed and applied to the spectrophotometric kinetic determination of creatinine in urine based on Jaffé's reaction. The flow network comprised microcomputer controlled three-way solenoid valves. With multicommutation, the potentialities of zone sampling and stopped-flow were expanded, and the design of the flow set up was simplified. Influence of the main related parameters such as system configuration, reagent concentrations, temperature and timing were studied. The proposed system handled about 24 samples per hour. Baseline drift was not observed during extended operation periods (8 h). Sample pretreatment was not required. Results were reproducible (R.S.D. < 3%) and in agreement with those obtained in a batch procedure.     

Structural analysis of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) fibers prepared by drawing and annealing processes

Structure of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) fibers prepared by drawing and annealing processes has been analyzed through wide-angle X-ray diffraction (WAXD), density, infrared dichroism, and birefringence measurements. There are three different types of crystalline structure in these fibers: two of these are the two types of orthorhombic with different orientation modes (the ordinary c-axis orientation (c//Z), and the preferential orientation of c-axis to the direction perpendicular to the fiber axis (c⟂Z)); and the third is pseudohexagonal. The weight fractions of the three types of crystals and amorphous phase were analyzed combining the WAXD integrated intensity and density data. The relation between crystalline orientation factors obtained separately from the WAXD measurement and the infrared dichroic ratio is also discussed. The birefringence of these fibers shows negative and positive values, depending on drawing and annealing temperatures. Considering the intrinsic birefringence and weight fraction of the c//Z, c⟂Z, and pseudohexagonal crystals, birefringence of the amorphous phase was evaluated. The amorphous birefringence shows positive values and decreases with an increase in the annealing temperature. From the analyzed fiber structure, it was speculated that the c⟂Z and pseudohexagonal crystals are preferentially formed in the drawing process irrespective of the drawing temperature.© 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2471–2482, 1998     

Flow injection analysis system for monitoring of succinic acid in biotechnological processes

In this study, a flow injection analysis (FIA) system using a cartridge of immobilized isocitrate lyase (ICL) and isocitrate dehydrogenase (ICDH) was developed to monitor the concentrations of succinic acid in biotechnological processes. The ICL and ICDH immobilized on VA-Epoxy Biosynth E3-carrier had a good operational lifetime (up to 24 h) and storage stability (up to 30 days). The FIA system with the immobilized ICL/ICDH cartridge was characterized with respect to the factors affecting the activity of the immobilized enzymes, such as pH of carrier solution, temperature, sample matrix, etc. Optimal pH value of the immobilized enzymes was slightly shifted in the alkaline range, i.e. 9.0. Some components such as 10 g l⁻¹ lactose, 3 g l⁻¹ malate and 3 g l⁻¹ oxaloacetate in sample solution had significant activating effects (more than 10%) on the response of the FIA system. But the activity of the immobilized ICL and ICDH was not largely influenced by some components like imidazole (1 mM), sodium azide (10 mM) and semicarbazide (2 g l⁻¹) added to carrier buffer solution. The FIA system with an enzyme cartridge was applied to on-line monitor the concentrations of succinic acid in a continuously stirred reactor and a fermentation process of immobilized Escherichia coli, and showed good sensitivity and reliability of the FIA system developed in this work.     

Flow injection kinetic spectrophotometric method for the determination of trace amounts of nitrite

In this work, a new, simple and sensitive flow injection catalytic kinetic spectrophotometric determination of nitrite is reported based on catalytic effect of nitrite on the redox reaction between sulfonazo III and potassium bromate in acidic media. The reaction was monitored by measuring the decrease in the absorbance of sulfunazo III at 570 nm. Various chemical (such as the effect of acidity, reagents concentrations) and instrumental parameters (flow rate, reaction coil length, injection volume and temperature) were studied and were optimized. Under the optimum conditions calibration graph was linear in the nitrite concentration ranges of 8.00 × 10⁻³-3.00 × 10⁻¹ μg/ml (with slope of 2.40) and 3.50 × 10⁻¹-1.80 μg/ml (with slope of 0.42). The detection limit was 6.00 × 10⁻³ μg/ml of nitrite, the relative standard deviation (n = 10) was 1.25% and 0.88% for 5.00 × 10⁻² and 2.00 × 10⁻¹ μg/ml of nitrite respectively. About 60 samples in 1 h can be analyzed. The interfering effects of various chemical species were studied. The method was successfully applied in the determination of nitrite in food and environmental samples.     

Kalman滤波流动注射化学发光法同时测定铂钯的研究

利用Luminol H2O2 OP Pt(Pd)化学发光新体系以及Kalman滤波化学计量学方法建立了流动注射化学发光法同时测定铂钯的新方法。方法的检出限:铂为2.2×10-8g mL、钯为2.4×10-8g mL,铂钯相对标准偏差分别为0.9%和3%。采用阳离子交换树脂静态吸附分离,消除贱金属离子的干扰。可用于贫铂矿中铂、钯的同时测定。     

Controlled biosynthesis and characterization of poly(3-hydroxybutyrate-co-3-hydroxyvalerate-co-3-hydroxyhexanoate) from mixtures of palm kernel oil and 3HV-precursors

This study investigates the biosynthesis and characterization of P(3HB-co-3HV-co-3HHx) terpolymer from mixtures of palm kernel oil and 3HV-precursors by using recombinant Cupriavidus necator PHB⁻4/pBBREE32d13. Sodium valerate and propionate have been evaluated for the generation of 3HV monomers. The feeding time of these precursors was a crucial factor that significantly affected the 3HV molar fractions, which ranged from 2 to 60 mol%. Sodium valerate was generally the better precursor in initiating the accumulation of 3HV monomers while maintaining high cell dry weight (7.9 g/L) and good PHA accumulation (79 wt%). However, the 3HHx molar fractions in the terpolymers at 72 h were consistent at about 2-7 mol%. P(3HB-co-3HV) copolymers have been known to exhibit approximately the same degree of crystallinity throughout a wide range of 3HV composition. Interestingly, in this study, terpolymers containing 58 mol% 3HB, 39 mol% 3HV and 3 mol% 3HHx showed elastomeric behavior. This study demonstrates the suitability of palm kernel oil as the main carbon source and both sodium propionate and sodium valerate as 3HV-precursors for the synthesis of novel compositions of P(3HB-co-3HV-co-3HHx) terpolymers with interesting properties.     

Simultaneous flow injection determination of calcium and fluoride in natural and borehole water with conventional ion-selective electrodes in series

An on-line automated system for the simultaneous flow injection determination of calcium and fluoride in natural and borehole water with conventional calcium-selective and fluoride-selective membrane electrodes as sensors in series is described. Samples (30 μl) are injected into a TISAB II (pH=5.50) carrier solution as an ionic strength adjustment buffer. The sample-buffer zone formed is first channeled to a fluoride-selective membrane electrode and then via the calcium-selective membrane electrode to the reference electrodes. The system is suitable for the simultaneous on-site monitoring of calcium (linear range 10⁻⁵–10⁻² mol l⁻¹ detection limit 1.94×10⁻⁶ mol l⁻¹ recovery 99.22%, RSD<0.5%) and fluoride (linear range 10⁻⁵–10⁻² mol l⁻¹ detection limit 4.83×10⁻⁶ mol l⁻¹ recovery 98.63%, RSD=0.3%) at a sampling rate of 60 samples h⁻¹.     

采用带微型预处理柱和分离柱的FIA分光光度系统同时测定硅和磷

用阳阴离子交换柱和流动注射分析组合,建立了在线预处理和预分离同时测定磷和硅的FIA方法。用本法测定了头发、淡菜、茶叶、马尾藻和大米中的硅和磷。方法的测定范围为1．0mg/L-24mg/L(PL4^3-),0.5mg/L-12mg/L(SiO3^2-),回收率：96.7%-99.0%(PO4^3-),100%-102%(SiO3^2-);RSD(PO4^3-)=1.3%,RSD(SiO3^2-)=1.8%。     

The degradation kinetics of poly(3-hydroxybutyrate) under non-aqueous and aqueous conditions

The degradation of poly(3-hydroxybutyrate), P(3HB), was determined in two conditions namely, a non-aqueous condition of chloroform-methanol mixture in the presence of either one of the two following catalysts, 4-toluenesulphonic acid and imidazole, and secondly in an aqueous condition of increasing pH. From our study, a random chain scission of PHB occurred in the non-aqueous condition while the degradation of PHB in the presence of water occurred through surface hydrolysis with no change in the molecular weight. In the surface hydrolysis of the polymer, the rate was increased with higher pH values.     

Effect of thermal degradation on rheological properties for poly(3-hydroxybutyrate)

Thermal degradation at processing temperature and the effect on the rheological properties for poly(3-hydroxybutyrate) have been studied by means of oscillatory shear modulus and capillary extrusion properties, with the aid of molecular weight measurements. Thermal history at processing temperature depresses the viscosity because of random chain scission. As a result, gross melt fracture hardly takes place with increasing the residence time in a capillary rheometer. Moreover, it was also found that the molecular weight distribution is independent of the residence time, whereas the inverse of the average molecular weight is proportional to the residence time. Prediction of average molecular weight with a constant molecular weight distribution makes it possible to calculate the flow curve following generalized Newtonian fluid equation proposed by Carreau as a function of temperature as well as the residence time.