Analytical evaluation of a cup-horn sonoreactor used for ultrasound-assisted extraction of trace metals from troublesome matrices

In this work, a sample preparation method based on ultrasound-assisted extraction of trace metals from a variety of biological and environmental matrices using a cup-horn sonoreactor is described. Diluted acids (HNO₃, HCl and HF) and oxidants (H₂O₂) were tried for extraction, the extracts being directly analyzed by electrothermal-atomic absorption spectrometry. The cup-horn sonoreactor combines the advantages of probe and bath sonicators, allowing a variety of conditions to be used for metal extraction from troublesome matrices. This system facilitates the use of HF to destroy the silicate lattice, application of simultaneous treatments of up to six samples and short treatment times. Quantitative metal recoveries are achieved from different matrices (animal and vegetal tissues, soil, sediment, fly ash, sewage sludge) under a set of extraction conditions ranging from the use of 3 min sonication time and 3% volume/volume HNO₃ for some animal tissues to 40 min sonication time along with 5% volume/volume HNO₃ + 20% volume/volume HF for sediment. Vegetal matter required the use of 5% volume/volume HNO₃ + 5% volume/volume HF for extraction of some elements.     

Determination of organophosphorous pesticides in water using in-syringe ultrasound-assisted emulsification and gas chromatography with electron-capture detection

An in-syringe ultrasound-assisted emulsification microextraction (USAEME) was developed for the extraction of organophosphorus pesticides (OPPs) from water samples. The OPPs subsequently analyzed gas chromatography (GC) using a microelectron capture detector (μECD). Ultrasound radiation was applied to accelerate the emulsification of μL-level low-density organic solvent in aqueous solutions to enhance the microextraction efficiency of OPPs in the sample preparation for GC-μECD. Parameters affecting the efficiency of USAEME, such as the extraction solvent, solvent volume, pH, salt-addition, and extraction time were thoroughly investigated. Based on experimental results, OPPs were extracted from a 5 mL aqueous sample by the addition of 20 μL toluene as the extraction solvent, followed by ultrasonication for 30 s, and then centrifugation for 3 min at 3200 rpm, offered the best extraction efficiency. Detections were linear in the concentration of 0.01–1 μg/L with detection limits between 1 ng/L and 2 ng/L for OPPs. Enrichment factors ranged from 330 to 699. Three spiked aqueous samples were analyzed, and recovery ranged from 90.1% to 104.7% for farm-field water, and 90.1% to 101.8% for industrial wastewater. The proposed method provides a simple, rapid, sensitive, inexpensive, and eco-friendly process for determining OPPs in water samples.     

Dynamic versus static ultrasonic sample treatment for the solid-liquid pre-concentration of mercury from human urine

Dynamic and static ultrasonic procedures involving ultrasonic bath and tandem focused ultrasound (i.e. two probes were used in the same sample treatment) have been assessed in order to implement a reliable solid-liquid back extraction of mercury from commercial resins (dowex and chelex-100), previously used to concentrate Hg(II) from treated urine. The urine had been previously treated with an advanced oxidation process provided by the conjunction of potassium permanganate, hydrochloric acid and high intensity focused ultrasound, which allowed that organic matter degradation was achieved in less than 3 min. 95 ± 10% of mercury in the certified urine and 97 ± 6% of the spiked methyl-mercury was recovered with the dowex resin plus the static ultrasonic procedure, whilst 96 ± 11% of the spiked mercury was recovered with the dowex resin plus the dynamic procedure, for which ultrasonication was not necessary. The Hg pre-concentration factor used in this work was 8 (20 mL of urine to 2.5 mL of acid), but different volume ratios can be used in order to increase this factor.     

High-throughput salting-out assisted liquid/liquid extraction with acetonitrile for the simultaneous determination of simvastatin and simvastatin acid in human plasma with liquid chromatography

Simvastatin (SS) is an effective cholesterol-lowering medicine, and is hydrolyzed to simvastatin acid (SSA) after oral administration. Due to SS and SSA inter-conversion and its pH and temperature dependence, SS and SSA quantitation is analytically challenging. Here we report a high-throughput salting-out assisted liquid/liquid extraction (SALLE) method with acetonitrile and mass spectrometry compatible salts for simultaneous LC-MS/MS analysis of SS and SSA. The sample preparation of a 96-well plate using SALLE was completed within 20 min, and the SALLE extract was diluted and injected into an LC-MS/MS system with a cycle time of 2.0 min/sample. The seamless interface of SALLE and LC-MS eliminated drying down step and thus potential sample exposure to room or higher temperature. The stability of SS and SSA in various concentration ratios in plasma was evaluated at room and low (4 °C) temperature and the low temperature (4 °C) was found necessary to maintain sample integrity. The short sample preparation time along with controlled temperature (2-4 °C) and acidity (pH 4.5) throughout sample preparation minimized the conversion of SS → SSA to ≤0.10% and the conversion of SSA → SS to 0.00% The method was validated with a lower limit of quantitation (LLOQ) of 0.094 ng mL⁻¹ for both SS and SSA and a sample volume of 100 μL. The method was used for a bioequivalence study with 4048 samples. Incurred sample reproducibility (ISR) analysis of 362 samples from the study exceeded ISR requirement with 99% re-analysis results within 100 ± 20% of the original analysis results.     

Ultrasonic energy as a tool in the sample treatment for polymer characterization through matrix-assisted laser desorption ionization time-of-flight mass spectrometry

Different ultrasonic devices including ultrasonic bath with dual frequency, sonoreactor and ultrasonic probe, were tested for their viability in the sample treatment for polymer characterization by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry analysis. The effect of sonication frequency (35 kHz, 40 kHz and 130 kHz), sonication amplitude, and sonication time on the polymer's number-average molecular weight (M_n) and weight-average molecular weight (M_w) were investigated. The effect of those variables in the molecular mass distribution of three polymer standards, poly(styrene) 2000 Da and 10,000 Da and poly(ethylene glycol) 1000 Da, was evaluated. In addition, the influence of ultrasonic energy on the sample treatment as a function of the matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI) matrix was also studied through two common standard matrices, dithranol and 2,5-dihydroxybenzoic acid. The results obtained show that the ultrasonic bath at 35 kHz is the best option for the purpose of fast sample treatment for polymer characterization. The M_n and M_w values obtained for this ultrasonic device and for the three polymers tested using dithranol as MALDI matrix, were not statistically different from the ones acquired with vortex mixing and also were in concordance with the values recommended by the polymer manufacturers.     

Ultrasound-assisted emulsification microextraction with simultaneous derivatization coupled to fibre optics-based cuvetteless UV-vis micro-spectrophotometry for formaldehyde determination in cosmetic samples

In this work, ultrasound-assisted emulsification microextraction in combination with fibre optics-based cuvetteless UV-vis micro-spectrophotometry has been proposed as a novel method for the determination of formaldehyde in water-based cosmetics such as shampoo, conditioner and shower gel. The use of a powerful cup-horn sonoreactor allows simultaneous extraction and derivatization of the samples without any pre-treatment. The type and volume of organic extractant solvent, need for a disperser solvent, sonication conditions (sonication time and amplitude), ionic strength and centrifuging time have been carefully studied. Matrix effects were also evaluated. The European official method for quantification of formaldehyde in cosmetic products was used for comparison purposes. An important improvement in sensitivity and sample throughput as well as miniaturization was achieved. A limit of detection of 0.02 μg g⁻¹ of formaldehyde and a repeatability expressed as relative standard deviation of 5.9% were obtained.     

Ultrasonic microdialysis coupled with capillary electrophoresis electrochemiluminescence study the interaction between trimetazidine dihydrochloride and human serum albumin

The paper describes a homemade ultrasonic microdialysis device coupled with capillary electrophoresis electrochemiluminescence (CE-ECL) for studying the interaction between human serum albumin (HSA) and trimetazidine dihydrochloride (TMZ). The time required for equilibrium by ultrasonic microdialysis was 45 min, which was far less than that by traditional dialysis (240 min). It took 80 min to achieve the required combination equilibrium by normal incubation and only 20 min by ultrasonic. Compared with traditional dialysis, the use of ultrasonic microdialysis simplified experimental procedures, shortened experimental time and saved consumption of sample. A simple, sensitive and selective determination of TMZ was developed using CE-ECL and the parameters that affected ECL intensity were optimized. Under the optimized conditions, the linear range of TMZ was from 0.075 to 80 μmol/L (r² = 0.9974). The detection limit was 26 nmol/L with RSD of 2.8%. The number of binding sites and binding constant were 1.54 and 15.17 L/mol, respectively.     

Accessing DNA by low voltage alternating current Joule effect heating

A DNA release sample preparation method based on the use of low voltage alternating currents (LVACs) to generate Joule effect heating (JEH) is reported. This is a simple cell disruption strategy that offers internal, homogenous, rapid and low power consumption heating for the access of analytical grade DNA in seconds.A 100 μL JEH microreactor with a parallel and symmetric two electrode arrangement for uniform field generation was fabricated by machining and used to characterise JEH and DNA release from human epithelia, yeast (Saccharomyces cerevisiae) and Gram-positive bacteria (Enterococcus faecium) cell types. A 1 kHz sinusoidal low voltage (e.g. 10 Vrms) alternating current was used to reduce electrode:sample interactions. Following 96 °C JEH treatment, effective DNA release was identified by PicoGreen^® quantification for all three cell types. The JEH treated sample material was further successfully used, without purification, as a PCR template. Exposure to JEH-mediated 96 °C temperatures for a 1 s duration was used to provide PCR-grade DNA template material from S. cerevisiae and E. faecium cells, and a 10 s duration was used for human epithelia cells. However, prolonged (>1 min) exposure to 96 °C JEH-mediated temperatures resulted in diminished DNA returns and the production of components that interfered with the PCR reaction.Further miniaturisation of the LVAC JEH cell by microfabrication was considered, and a JEH microreactor designs were evaluated by FLOTHERM v3.2 thermal modelling. Thermal isolation, using a free-standing cavity structure was identified as an excellent means to enable rapid heating (220 °C s⁻¹) with low power consumption (0.2 W).     

A simple microextraction and preconcentration approach based on a mixed matrix membrane

A simple adsorption/desorption procedure using a mixed matrix membrane (MMM) as extraction medium is demonstrated as a new miniaturized sample pretreatment and preconcentration technique. Reversed-phase particles namely polymeric bonded octadecyl (C₁₈) was incorporated through dispersion in a cellulose triacetate (CTA) polymer matrix to form a C₁₈-MMM. Non-steroidal anti-inflammatory drugs (NSAIDs) namely diclofenac, mefenamic acid and ibuprofen present in the environmental water samples were selected as targeted model analytes. The extraction setup is simple by dipping a small piece of C₁₈-MMM (7 mm × 7 mm) in a stirred 10 mL sample solution for analyte adsorption process. The entrapped analyte within the membrane was then desorbed into 100 μL of methanol by ultrasonication prior to high performance liquid chromatography (HPLC) analysis. Each membrane was discarded after single use to avoid any analyte carry-over effect. Several important parameters, such as effect of sample pH, salting-out effect, sample volume, extraction time, desorption solvent and desorption time were comprehensively optimized. The C₁₈-MMM demonstrated high affinity for NSAIDs spiked in tap and river water with relative recoveries ranging from 92 to 100% and good reproducibility with relative standard deviations between 1.1 and 5.5% (n = 9). The overall results obtained were found comparable against conventional solid phase extraction (SPE) using cartridge packed with identical C₁₈ adsorbent.     

Headspace liquid-phase microextraction of trihalomethanes in drinking water and their gas chromatographic determination

In the present work, a novel method for the determination of trihalomethanes (THMs) such as chloroform, dichlorobromomethane, chlorodibromomethane and bromoform in drinking water has been described. It is based on coupling headspace liquid-phase microextraction (HS-LPME) with gas chromatography-electron capture detector (GC-ECD). A microdrop of organic solvent at the tip of a commercial microsyringe was used to extract analytes from aqueous samples. Three organic solvents—xylene, ethylene glycol and 1-octanol—were compared and 1-octanol was the most sensitive solvent for the analytes. Extraction conditions such as headspace volume, extraction time, stirring rate, content of NaCl and extraction temperature were found to have significant influence on extraction efficiency. The optimized conditions were 15 ml headspace volume in a 40 ml vial, 10 min extraction time and 800 rpm stirring rate at 20 °C with 0.3 g ml⁻¹ NaCl. The linear range was 1-100 μg l⁻¹ for THMs. The limits of detection (LODs) ranged from 0.15 μg l⁻¹ (for dichlorobromomethane and chlorodibromomethane) to 0.4 μg l⁻¹ (for chloroform); and relative standard deviations (RSD) for most of THMs at the 10 μg l⁻¹ level were below 10%. Real samples collected from tap water and well water were successfully analyzed using the proposed method. The recovery of spiked water samples was from 101 to 112%.     

Fast analysis of multiple pesticide residues in apple juice using dispersive liquid–liquid microextraction and multidimensional gas chromatography–mass spectrometry

A method for the rapid trace analysis of 24 residual pesticides in apple juice by multidimensional gas chromatography–mass spectrometry (MD-GC/MS) using dispersive liquid–liquid microextraction (DLLME) was developed and optimized. Several parameters of the extraction procedure such as type and volume of extraction solvent, type and volume of dispersive solvent and salt addition were evaluated to achieve the highest yield and to attain the lowest detection limits. The DLLME procedure optimized consists in the formation of a cloudy solution promoted by the fast addition to the sample (5 ml) of a mixture of carbon tetrachloride (extraction solvent, 100 μl) and acetone (dispersive solvent, 400 μl). The tiny droplets formed and dispersed among the aqueous sample solution are further joined and sedimented (85 μl) in the bottom of the conical test tube by centrifugation. Once extracted, all the 24 pesticides were directly injected and separated by a dual GC column system, comprising a short wide-bore DB-5 capillary column with low film thickness connected by a Deans switch system to a second chromatographic narrower column, with identical stationary phase. The instrumental setting used, in combination with carefully optimized operational fast GC and MS parameters, markedly decreased the retention times of the targeted analytes. The total chromatographic run was 8 min. Mean recoveries for apple juice spiked at three concentrations ranged from 60% to 105% and the intra-repeatability ranged from 1% to 21%. The limits of detection of the 24 pesticides ranged from 0.06 to 2.20 μg/L. In 2 of a total of 28 analysed samples were found residues of captan, although at levels below the maximum limit legal established.     

Tandem focused ultrasound (TFU) combined with fast furnace analysis as an improved methodology for total mercury determination in human urine by electrothermal-atomic absorption spectrometry

A new sample preparation procedure based on tandem (that is, different diameter probe sonicators used in the same sample treatment) focused ultrasound (TFU) for mercury separation, preconcentration and back-extraction in aqueous solution from human urine has been developed. The urine is first oxidized with KMnO₄/HCl/focused ultrasound (6 mm probe). Secondly, the mercury is extracted and preconcentrated with dithizone and cyclohexane. Finally, the mercury is back-extracted and preconcentrated again with the aid of focused ultrasound (3 mm probe). The procedure allows determining mercury by electrothermal atomic absorption spectrometry with fast furnace analysis and calibration against aqueous standards. Matrix modification is provided by the chemicals used in the sample treatment. The procedure is accomplished with low sample volume (8.5 ml). Low volume and low concentration reagents are used. The sample treatment is rapid (less than 3 min per sample) and avoids the use of organic phase in the graphite furnace. The preconcentration factor used in this work was 14. The limit of detection and the limit of quantification in urine were, respectively, 0.27 and 0.9 μg l⁻¹. The relative standard deviation of aqueous standards (n=10) was 4% for a concentration of 100 μg l⁻¹ and 5% for a concentration of 400 μg l⁻¹. Recoveries from spiked urine with inorganic mercury, methyl-mercury, phenyl-mercury and diphenyl-mercury ranged from 86 to 98%.     

Study of the factors affecting the performance of microextraction by packed sorbent (MEPS) using liquid scintillation counter and liquid chromatography-tandem mass spectrometry

Microextraction by packed sorbent (MEPS) is a new technique for sample preparation that can be connected on-line with LC or GC. In MEPS, approximately 1-2 mg of the solid packing material is inserted into a syringe (100-250 μL) as a plug. Sample preparation takes place on the packed bed. The bed can be packed or coated to provide selective and suitable sampling conditions. The new method is very promising for extraction of drugs and metabolites from biological samples.In this paper, some factors affecting the performance of MEPS such as recovery, carry-over, leakage, washing volume and elution volume were studied using C18 and hydroxylated polystyrene-divinylbenzene copolymer (ENV+) as sorbents. Radioactively labelled bupivacaine in plasma samples was used as test analyte. For the extraction of this drug, using methanol/water 95:5 (v/v) (0.25% ammonium hydroxide) was used as elution solvent. The analyte response increased with increasing the elution volume and it was linear upp up to 100 μL utilizing liquid scintillation counter. Further, for concentrating the sample, we found that MEPS may be used such that the sample can be drawn through the needle, up and down, several times. The analyte leakage increases as the volume washing increases, though higher washing volumes may also result in cleaner extracts. To eliminate analyte carry-over, the sorbents were washed first with 3 × 250 μL elution solution and then with 3 × 250 μL washing solution. In addition, the reproducibility measurements show relatively good relative standard deviation (RSD) % values concerning analyte recovery and analyte leakage. The present study provides an understanding of basic aspects when optimizing methods for MEPS. In this study, MEPS was used off-line with liquid scintillation counter and on-line with LC-MS/MS.     

An improved clean sonoreactor-based method for protein identification by mass spectrometry-based techniques

A new clean fast (8 min) method for in-solution protein digestion without detergent or urea for protein identification by peptide mass fingerprint and mass spectrometry-based techniques is proposed. The new method avoids the use of time consuming desalting procedures entailing the following four steps done under the effect of an ultrasonic field provided by a sonoreactor: denaturation (1 min) in a mixed solution of water:acetonitrile 1/1 (v/v); protein reduction (1 min); protein alkylation (1 min); and protein digestion (5 min). Five proteins with masses comprised between 14.4 kDa and 97 kDa and the protein split-soret cytochrome c from D. desulfuricans ATCC27774, were successfully identified with this procedure. No differences were found in the sequence coverage or in the number of peptides matched when the new clean method was compared to another one using urea. Twofold better signal-to-noise ratios were obtained in the MALDI spectra from protein samples prepared with the new method when comparing it with a method using urea. The new digestion method avoids the need to remove salt content and increases throughput (six samples at once) while reducing sample loss and contamination from sample handling.     

High-performance liquid chromatographic-UV detection analysis of ceftiofur and its active metabolite desfuroylceftiofur in horse plasma and synovial fluid after regional intravenous perfusion and systemic intravenous injection of ceftiofur sodium

A method was optimalised for the quantitative determination of ceftiofur and its active metabolite desfuroylceftiofur in horse plasma and synovial fluid.The principle of the method was that bound desfuroylceftiofur is first released by dithioerythritol, a reducing agent, followed by the derivatization of the free sulfhydryl group with iodoacetamide. The stable derivative—desfuroylceftiofuracetamide—was then further purified using an Oasis HLB solid-phase extraction column. Chromatography was performed using a PLRP-S polymeric column (100 Å, d_p: 5 μm,  mm i.d.), with a mixture of 0.1% trifluoro acetic acid in water and acetonitrile as the mobile phase. Gradient elution was performed. The flow-rate was 0.4 ml/min and the UV detector was set at a wavelength of 266 nm. The method was validated in plasma and synovial fluid (linearity, precision, trueness, LOQ, LOD, specificity, susceptibility to interferences). Calibration graphs were prepared over a concentration range of 0-20 μg/ml and good linearity was achieved (r≥0.99, g≤10%). A limit of quantification of 0.5 μg/ml was obtained for ceftiofur in both matrices. Limits of detection were 0.36 and 0.27 μg/ml for ceftiofur in plasma and synovial fluid, respectively. The results of the within-run and between-run precision and the trueness fell within the ranges specified.The main advantage of our method, compared to previously reported methods, was that the sample preparation procedure was less time consuming, resulting in a higher sample throughput (up to 40 samples a day). In addition, the analysis cost was reduced due to the consumption of a lower amount of solvents and reagents and of only one solid-phase extraction column per sample. The method was successfully applied during a pharmacokinetic study in horses after the administration of ceftiofur sodium via regional intravenous perfusion and systemic intravenous injection.     

Nano-electromembrane extraction

The present work has for the first time described nano-electromembrane extraction (nano-EME). In nano-EME, five basic drugs substances were extracted as model analytes from 200 μL acidified sample solution, through a supported liquid membrane (SLM) of 2-nitrophenyl octyl ether (NPOE), and into approximately 8 nL phosphate buffer (pH 2.7) as acceptor phase. The driving force for the extraction was an electrical potential sustained over the SLM. The acceptor phase was located inside a fused silica capillary, and this capillary was also used for the final analysis of the acceptor phase by capillary electrophoresis (CE). In that way the sample preparation performed by nano-EME was coupled directly with a CE separation. Separation performance of 42,000–193,000 theoretical plates could easily be obtained by this direct sample preparation and injection technique that both provided enrichment as well as extraction selectivity. Compared with conventional EME, the acceptor phase volume in nano-EME was down-scaled by a factor of more than 1000. This resulted in a very high enrichment capacity. With loperamide as an example, an enrichment factor exceeding 500 was obtained in only 5 min of extraction. This corresponded to 100-times enrichment per minute of nano-EME. Nano-EME was found to be a very soft extraction technique, and about 99.2–99.9% of the analytes remained in the sample volume of 200 μL. The SLM could be reused for more than 200 nano-EME extractions, and memory effects in the membrane were avoided by effective electro-assisted cleaning, where the electrical potential was actively used to clean the membrane.     

Ultrasound-assisted emulsification microextraction method based on applying low density organic solvents followed by gas chromatography analysis for the determination of polycyclic aromatic hydrocarbons in water samples

In this study, a fast, simple and efficient ultrasound-assisted emulsification microextraction (USAEME) method was successfully developed based on applying low density organic solvents. Fourteen microliters of toluene was injected slowly into a 12 mL home-designed centrifuge glass vial containing an aqueous sample that was located inside the ultrasonic water bath. The formed emulsion was centrifuged and 2 μL of separated toluene (about 4 μL) was injected into a gas chromatographic system equipped with a flame ionization detector (GC-FID) for analysis. Some polycyclic aromatic hydrocarbons (PAHs) were selected as model compounds for developing the method and evaluating its performance and to compare the efficiency of the proposed method with previously reported techniques. Several factors influencing the emulsification, extraction and collection efficiency such as the nature and volume of organic solvent, emulsification–extraction temperature, ionic strength and equilibrium and centrifugation times were investigated and optimized. Under the optimum conditions, preconcentration factors (PFs) in a range of 1776–2714 were obtained. The performance of the proposed method was studied in terms of linear dynamic range (LDRs from 0.05 to 100 μg L⁻¹), linearity (R² ≥ 0.994), precision (repeatability: RSD% ≤ 7.9, reproducibility: RSD% ≤ 14.6) and extraction percents (59.2–90.5%). Limits of detection (LODs) in the range of 0.02–0.05 μg L⁻¹ were obtained for different PAHs. The applicability of the proposed method was evaluated by the extraction and determination of PAHs from several natural water samples.     

An electrochemical assay for the determination of Se (IV) in a sequential injection lab-on-valve system

A sequential injection lab-on-valve (LOV) unit, integrating a miniaturized electrochemical flow cell (EFC), has been constructed for the determination of trace amounts of Se (IV) by employing cathodic stripping voltammetry (CSV) technique. The procedure is carried out on a mercury film coated glassy carbon electrode. The analyte solution and electrolyte solution were continuously aspirated and merged in the holding coil (HC) by using a single syringe pump, which were afterwards pushed into the EFC, where the peak current was generated during the subsequent deposition/stripping procedure and measured as the basis of quantification. Assay parameters were optimized in order to achieve the best analytical performance, including mercury film preparation, supporting electrolyte composition, deposition potential and deposition time, and flow variables in the LOV. By loading a sample volume of 500 μL, a linear calibration graph was derived within 1-600 μg L⁻¹, and a detection limit (3б) of 0.11 μg L⁻¹ was achieved along with a sampling frequency of 20 h⁻¹. By integrating the EFC into the LOV unit, the assembling system not only minimized the sample/reagent consumption and waste generation, but also enhanced the sampling frequency. The work itself extended the applications of electrochemical detection techniques and provided a good platform for Se (IV) electrochemical analysis.     

Ultrasound assisted extraction of phenolic compounds from grapes

A new ultrasound-assisted extraction method was developed for the determination of phenolic compounds present in grapes. Several extraction variables including extraction temperature (0–75 °C), output amplitude (20, 50 and 100%), duty cycle (0.2 s, 0.6 s and 1 s), the quantity of sample (0.5–2 g), and the total extraction time (3–15 min) were evaluated. One of the most widely used extraction methods of polyphenol extraction has been used as reference method. Three parameters were compared: total amount of phenolic compounds, total amount of anthocyanins and total amount of tannic components. The resulting method produced similar or higher recoveries for these three parameters; however a much shorter extraction time was needed: 6 min (ultrasound assisted extraction method) instead of 60 min (reference method).     

Liquid-phase microextraction in a microfluidic-chip – High enrichment and sample clean-up from small sample volumes based on three-phase extraction

In this work, a microfluidic-chip based system for liquid-phase microextraction (LPME-chip) was developed. Sample solutions were pumped into the LPME-chip with a micro-syringe pump at a flow rate of 3–4 μL min⁻¹. Inside the LPME chip, the sample was in direct contact with a supported liquid membrane (SLM) composed of 0.2 μL dodecyl acetate immobilized in the pores of a flat membrane of polypropylene (25 μm thickness). On the other side of the SLM, the acceptor phase was present. The acceptor phase was either pumped at 1 μL min⁻¹ during extraction or kept stagnant (stop-flow). Amitriptyline, methadone, haloperidol, loperamide, and pethidine were selected as model analytes, and they were extracted from alkaline sample solution, through the SLM, and into 10 mM HCl or 100 mM HCOOH functioning as acceptor phase. Subsequently, the acceptor phase was either analyzed off-line by capillary electrophoresis for exact quantification, or on-line by UV detection or electrospray ionization mass spectrometry for time profiling of concentrations. The LPME-chip was found to be highly effective, and extraction efficiencies were in the range of 52–91%. When the flow of acceptor phase was turned off during extraction (stop-flow), analyte enrichment increased linearly with the extraction time. After 10 min as an example, amitriptyline was enriched by a factor of 42 from only 30 μL sample solution, and after 120 min amitriptyline was enriched by a factor of 500 from 320 μL sample solution. This suggested that the LPME-chip has great potentials for very efficient analyte enrichments from limited sample volumes in the future.