介孔SBA-15的形貌控制合成及负载染料后其光学性能研究

采用水热-组装法、溶剂挥发法等材料合成方法制备了不同形貌(粉末棒状、单块、薄膜)负载染料的介孔SBA-15复合材料, 并开展光学性质研究. 通过TEM, XRD, N₂吸附-脱附表征证明所合成的各种形貌SBA-15材料均具有规则有序介孔结构, 组装染料后复合材料的形貌及结构保持完整|Uv-vis, PL表征表明染料在SBA-15孔道中呈单分散状态, 负载染料后的复合材料具有发光特性.     

"面包圈"状高有序度大孔径介孔分子筛SBA-15的合成

介孔材料因其高度有序的大孔径、较佳的催化吸附性能、良好的电磁性质及易于剪裁而引起人们极大的兴趣[1～9].人们已相继合成了介孔氧化硅薄膜[3,10]、球[12]、空心球[4,13]和纤维[12～15]等,并设法控制中孔材料晶体外貌[3～9,15～21].最近,我们报道了利用多相组装和无机晶体(如NaCl,LiCl)作大孔结构导向剂的方法[16],合成了人造"珊瑚"状介-大孔氧化硅膜[13].Lin等[17]用共表面活性剂法在丁醇存在下合成了多组有序结构的介孔氧化硅空心球; Shio等[21]在完全溶解的硅酸钠和阳离子表面活性剂溶液中,合成了细棒状介孔氧化硅粉末.本文报道一种控制介孔材料颗粒外貌和形状的新方法,即共溶剂法,并以此法合成了高有序度、大孔径、 "面包圈"状介孔氧化硅SBA-15.这种新材料有望在微加工、催化、生物分离、电子器件的矿化、色谱载体等方面得到应用[1～9].     

有序介孔二氧化硅对正丁醛的吸附性能

合成了一系列具有不同孔结构与性质的有序介孔二氧化硅材料SBA-15、MCM-41、SBA-16、KIT-6, 同时通过改变水热温度制备了不同孔径大小的SBA-15, 并利用小角X射线散射、透射电镜、扫描电镜和氮气吸附-脱附等手段, 对其介孔结构进行了表征. 以正丁醛为探针分子, 考察了其对有机醛的吸附, 并与Y-沸石的吸附性能做了对比. 结果表明, 材料的介孔比表面积与其对正丁醛的吸附量成正比, 吸附等温线符合Langmuir 模型, 属于单层吸附, 具有最大介孔比表面积的MCM-41对正丁醛的吸附量最大(484 mg·g^-1). 最后将SBA-15添加到卷烟滤嘴中, 实验结果表明, SBA-15能显著降低卷烟烟气中巴豆醛的释放量.     

大粒径介孔氧化硅微球的优化合成及表征

以非离子型嵌段共聚物为模板剂、正硅酸乙酯为硅源,制备了一种比表面积为712m2·g-1、孔径6.93nm、孔容1.06cm3·g-1、粒径10μm的介孔SBA-15微球,采用扫描电镜考察了各种合成条件对介孔氧化硅微球形貌的影响,对SBA-15介孔微球的合成条件优化和形成机理进行了研究和探讨。结果表明:介孔氧化硅微球的生长可以看作一个由微小溶胶粒子发生渐进聚沉、成长为较大溶胶粒子的过程;共表面活性剂和无机盐的引入对介孔微球的形成具有辅助作用;合成体系的酸度和晶化阶段之前的陈化条件是介孔微球形成的关键所在。在共聚物的盐酸溶液(1mol·L-1)中,不添加共表面活性剂和无机盐,仅控制陈化条件于35℃静置24h,100℃水热处理24h,可得到大粒径的介孔SBA-15微球。     

有序介孔二氧化硅对正丁醛的吸附性能

合成了一系列具有不同孔结构与性质的有序介孔二氧化硅材料SBA-15、MCM-41、SBA-16、KIT-6,同时通过改变水热温度制备了不同孔径大小的SBA-15,并利用小角X射线散射、透射电镜、扫描电镜和氮气吸附-脱附等手段,对其介孔结构进行了表征.以正丁醛为探针分子,考察了其对有机醛的吸附,并与Y-沸石的吸附性能做了对比.结果表明,材料的介孔比表面积与其对正丁醛的吸附量成正比,吸附等温线符合Langmuir模型,属于单层吸附,具有最大介孔比表面积的MCM-41对正丁醛的吸附量最大(484 mg·g-1).最后将SBA-15添加到卷烟滤嘴中,实验结果表明,SBA-15能显著降低卷烟烟气中巴豆醛的释放量.     

有序介孔炭的合成及液相有机大分子吸附性能研究

分别采用有序介孔氧化硅SBA-15和NaY分子筛为硬模板合成了系列有序介孔炭OMC和微孔炭CFY. N₂静态吸附测试表明, 所合成的介孔炭具有丰富的介孔结构和集中的介孔分布. 以亚甲基蓝为探针分子, 研究其在有序介孔炭OMC和微孔炭CFY上的吸附行为. 研究结果表明, 有序介孔炭中大于3.5 nm的大介孔孔容是决定亚甲基蓝吸附容量和吸附速率的关键因素. 吸附动力学理论研究表明, 准二级动力学方程可以很好地描述亚甲基蓝分子在介孔炭上吸附动力学行为.     

镁热还原法制备有序介孔Si/C锂离子电池负极材料及其电化学性能

以SBA-15为前驱体,在660 ℃下通过镁热还原反应得到介孔硅材料,并对其进行碳包覆处理,成功地制备了有序介孔Si/C（OMP-Si/C）复合材料。该OMP-Si/C材料保留了SBA-15模板的有序蜂窝孔道,并且形成具有高堆积密度的莲藕链束结构。文中还提出了一个SBA-15镁热还原液态环境反应模型,探讨了660 ℃下硅的高度有序介孔与莲藕链束结构的形成机理。利用X射线衍射（XRD）仪、扫描电子显微镜（SEM）、透射电子显微镜（TEM）、氮气吸脱附法及拉曼光谱对样品物相和微观形貌进行了表征。这种高度有序介孔Si/C复合材料具有优异的电化学性能,展现出其在第二代锂电池负极材料领域中的潜在应用价值。     

新型有机-无机杂化碱性介孔材料的合成——空间位阻对催化性能的影响

通过直接合成方法制备了2个二级胺功能化的SBA-15型有机-无机杂化碱性介孔材料. 粉末X射线衍射分析、氮气吸附-脱附和透射电镜表征表明, 合成的材料保持了SBA-15的有序介孔孔道结构, 而热重、红外光谱和元素分析表明有机功能团被成功引入. 在对硝基苯甲醛和丙酮的羟醛缩合反应中, 相对于一级胺功能化的材料, 二级胺功能化的SBA-15展示了极大改进的催化活性, 这可能是由于具有更大空间位阻效应的有机功能团的引入导致了碱性胺中心催化活性增强.     

介孔分子筛SBA-15作为高效液相色谱固定相分离维生素E

以三嵌段共聚物P123聚环氧乙烷-聚环氧丙烷-聚环氧乙烷(PEO-PPO-PEO)为模板,在强酸性(1.6mol/L HCl)条件下,水热合成了棒状二维六方有序介孔材料SBA-15.粒径棒长约1～1.5μm,直径为400～500nm,平均孔径5.8nm,BET比表面积799㎡/g.并用合成的SBA-15作为正相高效液相...     

有机/无机复合介孔膜的合成及其生物酶吸附行为研究

以正硅酸四乙酯(TEOS)为硅源、三嵌段共聚物(F127)为表面活性剂, 聚碳酸酯膜为硬模板, 并采用抽滤法在聚碳酸酯膜内的亚微米级孔道中组装介孔氧化硅从而制备出有机(聚碳酸酯)/无机(介孔氧化硅)复合介孔膜. 通过扫描电镜、能量分散光谱以及透射电镜等实验表征了该有机/无机复合介孔膜的组成、结构及形貌. 研究结果表明: 通过该方法可以在聚碳酸酯膜内孔道中形成长度为9 μm、直径为200 nm的一维氧化硅棒状材料, 且该棒状材料具有无序蠕虫状和有序体心立方的混合介孔结构, 有序体心立方介孔的平均孔径约为8.5 nm. 另外, 初步考察了该复合介孔膜对生物酶的物理吸附行为, 结果表明其对肌红蛋白酶的单位吸附负载量为5.85 mg/g.     

Synthesis, characterization and catalytic behavior of functionalized mesoporous SBA-15 with various organo-silanes

Mesoporous silica SBA-15 has been synthesized and functionalized by one-step synthesis method to widen their various application possibilities. In this study, phenyltrimethoxysilane (PTMS), 3-mercaptopropyltrimethoxysilane (MPTMS) and trimethoxypropylsilane (TMPS) were used as silane precursors for the functionalization, and after treated with HCl solution, their catalytic activities were evaluated in the lactic acid-methanol esterification. The presence of anchoring of functional groups on SBA-15 was proved by XRD, FT-IR, BET surface area and pore size distributions. Good catalytic activity was observed especially for SBA-15-SO(3)H-MPTMS, and the catalytic activity order was determined as follows: SBA-15-SO(3)H-MPTMS>SBA-15-TMPS>SBA-15-PTMS, which is directly associated with the surface area, pore size and pore volume. As compared with homogeneous catalyst, SBA-15-SO(3)H-MPTMS heterogeneous catalyst shows remarkable performance, such as separation, recovery and reusability.     

Rapid synthesis of SBA-15 rods with variable lengths, widths, and tunable large pores

Dispersed SBA-15 rods have been synthesized with varying lengths, widths, and pore sizes in a low-temperature synthesis in the presence of heptane and NH(4)F. The pore size of the material can systematically be varied between 11 and 17 nm using different hydrothermal treatment times and/or temperatures. The particle length (400-600 nm) and width (100-400 nm) were tuned by varying the HCl concentration. All the synthesized materials possess a large surface area of 400-600 m(2)/g and a pore volume of 1.05-1.30 cm(3). A mechanism for the effect of the HCl concentration on the particle morphology is suggested. Furthermore, it is shown that the reaction time can be decreased to 1 h, with well-retained pore size and morphology. This work has resulted in SBA-15 rods with the largest pore size reported for this morphology.     

Controlled drug release from bifunctionalized mesoporous silica

Serial of trimethylsilyl-carboxyl bifunctionalized SBA-15 (TMS/COOH/SBA-15) have been studied as carriers for controlled release of drug famotidine (Famo). To load Famo with large capacity, SBA-15 with high content of carboxyl groups was successfully synthesized by one-pot synthesis under the assistance of KCl. The mesostructure of carboxyl functionalized SBA-15 (COOH/SBA-15) could still be kept even though the content of carboxyl groups was up to 57.2%. Increasing carboxyl content could effectively enhance the loading capacity of Famo. Compared with pure SBA-15, into which Famo could be hardly adsorbed, the largest drug loading capacity of COOH/SBA-15 could achieve 396.9 mg/g. The release of Famo from mesoporous silica was studied in simulated intestine fluid (SIF, pH=7.4). For COOH/SBA-15, the release rate of Famo decreased with narrowing pore size. After grafting TMS groups on the surface of COOH/SBA-15 with hexamethyldisilazane, the release of Famo was greatly delayed with the increasing content of TMS groups.     

Thermogravimetry applied to characterization of SBA-15 nanostructured material

Nanoporous silica with narrow pore size distribution has attracted increasing attention as a novel material for separations and reactions involving large molecules. SBA-15 has been synthesized in an acidic medium using a triblock copolymer as template. In this work, the SBA-15 was synthesized by the hydrothermal treatment at 373 K for 48 h, of a gel with the following overall molar composition: 1.0TEOS:0.017P123:5.7HCl:193H₂O, where TEOS is tetraethyl orthosilicate and P123 is poly(ethylene oxide, propylene oxide and 1,4-dioxane). The obtained material was characterized by thermogravimetry, X-ray diffraction, infrared spectroscopy and BET surface area. A kinetic study using the model free model was accomplished in the stage of decomposition of the template (P123). The obtained value of the apparent activation energy was ca. 131 kJ mol^–1.     

SBA-15固载脯氨酸催化剂的制备及其在不对称Mannich反应中的应用

以4-羟基-L-脯氨酸为原料合成了脯氨酸衍生物,并将其固载于介孔SBA-15分子筛上制备了Pro/SBA-15催化剂.用X射线衍射、N2吸附-脱附、扫描电镜和红外光谱等手段对Pro/SBA-15催化剂进行了表征,并考察了催化剂在不对称Mannich反应中的催化性能.结果表明,固载脯氨酸不影响SBA-15的有序介孔结构,只是其孔径、孔体积和BET比表面积有所减小,在不对称Mannich反应中具有较高的催化活性和对映选择性.与均相催化相比,以对硝基苯甲醛为反应物时可得到较高的分离收率(80%)和中等的对映选择性(ee=60%).催化剂通过简单分离后可重复使用4次以上,其催化性能基本保持不变.     

长度可控杆状SBA-15的合成简

以三嵌段共聚物P123为结构导向剂,天然高聚物壳聚糖为添加剂,合成出分散性较好的杆状结构SBA-15. 通过调节体系中壳聚糖的含量,可以实现对产物形貌的控制,即从颗粒到短杆状,最后到长杆状. 壳聚糖的加入不仅使SBA-15的介孔结构更加长程有序,同时也提高了其比表面积和孔容,其最高值分别达到1157 m2/g和1.53 cm3/g.     

Ag/SBA-15表面催化过程的现场SERS研究

以三嵌段共聚物P₁₂₃为模板剂, 正硅酸乙酯为硅源, 水热合成了介孔分子筛SBA-15, 通过对SBA-15内外表面修饰, 使用银氨溶液和硝酸银溶液作为金属源合成Ag/SBA-15, 透射电镜(TEM)研究表明在SBA-15孔道内较好地分散了颗粒状和棒状的Ag纳米粒子. 以苯硫酚作为探针分子, 研究了负载Ag纳米粒子的SBA-15的SERS效应, 结果表明Ag/SBA-15具有良好的SERS活性. 另外, 该材料对催化硼氢化钠还原对硝基苯酚具有良好的催化效果, 通过结合现场SERS技术, 研究了该催化过程的机理.     

长度可控杆状SBA-15的合成

以三嵌段共聚物P123为结构导向剂, 天然高聚物壳聚糖为添加剂, 合成出分散性较好的杆状结构SBA-15. 通过调节体系中壳聚糖的含量, 可以实现对产物形貌的控制, 即从颗粒到短杆状, 最后到长杆状. 壳聚糖的加入不仅使SBA-15的介孔结构更加长程有序, 同时也提高了其比表面积和孔容, 其最高值分别达到1157 m²/g和1.53 cm³/g.     

Static and dynamic sorption study of heavy metal ions on amino-functionalized SBA-15

Amino-functionalized SBA-15 mesoporous silica (SBA-15-NN) was synthesized using the normal grafting procedure of SBA-15 with [3-(2-Aminoethyl) aminopropyl] trimethoxysilane. Under optimal conditions, SBA-15-NN exhibited a higher adsorption capacity toward metal ions than SBA-15 in static adsorption. The results showed that the flow rate of 2?mL?min^?1 might be the optimum flow rate in dynamic adsorption, and the higher initial metal ion concentration is favorable for the adsorption of Zn(II), Co(II), and Ni(II) onto SBA-15-NN. The results indicated that SBA-15-NN could effectively remove multiple metal ions from aqueous solution as a good adsorption material.     

高分散TiO_2/SBA-15的制备及光催化性能

提出了一种制备高分散TiO2/SBA-15光催化剂的新方法.以钛酸四正丁酯(TB)和羧基改性的SBA-15(COOH/SBA-15)为原料,利用COOH/SBA-15表面上高分散的羧基与TB的配合作用将TB锚定,经过溶剂热及焙烧处理制得TiO2/SBA-15光催化剂.采用粉末X射线衍射(XRD),N2吸脱附,傅里叶变换红外光谱(FT-IR),透射电镜(TEM)等对所得催化剂进行了表征.结果表明:所得TiO2/SBA-15光催化剂为高结晶度的锐钛矿晶型,TiO2均匀地分散在SBA-15表面,TiO2/SBA-15光催化剂保持较好的介孔特征结构,具有较大比表面积.以降解罗丹明B(RhB)为探针反应,考察了所得TiO2/SBA-15光催化剂的光催化性能.与后处理浸渍法制备的光催化剂相比,本文制备的TiO2/SBA-15光催化剂表现出了更加优越的光催化性能.