Preparation of oriented titanium phosphate and tin phosphate/polyaniline hybrid films by electrochemical deposition

The preparation of hybrid films of metal (Ti and Sn) phosphate nanosheets and polyaniline by simultaneous electrophoretic and electrolytic deposition was performed in an acetonitrile solvent. Emeraldine polyaniline was intercalated between the phosphate nanosheets with a monolayer arrangement. The obtained hybrid films were several tens of micrometers in thickness. The ratio of incorporated polyaniline to metal phosphate in the hybrid films reaches to around 0.45 and 0.30 at suitable concentrations of tetrabutylammonium hydroxide (TBAOH). These amounts correspond with occupancy of polyaniline in the interlayer gallery of several tens percent. Fractions of voids in a horizontal direction were around 22 and 1% in titanium phosphate/polyaniline and tin phosphate/polyaniline hybrid films, respectively. Thus, anodic electrodeposition makes it possible to form thick films of intercalation compounds of alpha-titanium and tin phosphates with polyaniline. These hybrid films were examined for redox activity. The cyclic voltammetry results of these films confirmed that the hybrid films have redox activity by polyaniline. For these voltammograms, the maximum current was observed in the tin phosphate/polyaniline hybrid deposited for 15 min. The redox activity of these hybrids possibly depends on the mesoscopic texture of the film, especially on the amount of voids in a horizontal direction.     

High-yield synthesis of few-layer graphene flakes through electrochemical expansion of graphite in propylene carbonate electrolyte

High-yield production of few-layer graphene flakes from graphite is important for the scalable synthesis and industrial application of graphene. However, high-yield exfoliation of graphite to form graphene sheets without using any oxidation process or super-strong acid is challenging. Here we demonstrate a solution route inspired by the lithium rechargeable battery for the high-yield (>70%) exfoliation of graphite into highly conductive few-layer graphene flakes (average thickness <5 layers). A negative graphite electrode can be electrochemically charged and expanded in an electrolyte of Li salts and organic solvents under high current density and exfoliated efficiently into few-layer graphene sheets with the aid of sonication. The dispersible graphene can be ink-brushed to form highly conformal coatings of conductive films (15 ohm/square at a graphene loading of <1 mg/cm(2)) on commercial paper.     

Stable G-quadruplex structure in a hydrated ion pair: cholinium cation and dihydrogen phosphate anion

A combination of cholinium cations and dihydrogen phosphate anions is indispensable for the G-quadruplex structure regardless of water content. No G-quadruplex structure was observed in most salts even containing either cholinium cations or dihydrogen phosphate anions.     

Influence of operating conditions on the retention of phosphate in water by nanofiltration

The objective of this study was to investigate the retention of phosphate anions, H₂PO₄⁻ and HPO₄²⁻, by nanofiltration. The first part of this study deals with the characterisation of the NF200 membrane used in permeation experiments with aqueous solutions of neutral organic and charged inorganic solutes. In the second part the effects of feed pressure, ionic strength, concentration and pH on the retention of phosphate anions were investigated. Results show that the membrane is negatively charged, its pore radius is around 0.5 nm and the retention order for the salts tested was R(Na₂SO₄) > R(NaCl) > R(CaCl₂). The retentions of phosphate anions are in the order of 85% for H₂PO₄⁻ and 96% for HPO₄²⁻. They are relatively high when compared to retentions of other anions with the same charge. The retentions of phosphate anions, particularly the monovalent species, depend on the chemical parameters (feed concentration, ionic strength, and pH) and applied pressure. The experimental data were analysed using the Speigler–Kedem model and the transport parameters, i.e., the reflection coefficient (σ) and solute permeability (P_s) have been determined.     

A New Category of Liquid Salt--Liquid Ionic Phosphates (LIPs)

Starting with polycationic ammonium and phosphonium salts bearing halide anions previously synthesized in our laboratory, we have prepared a new category of nonaqueous ionic liquids. These new nonaqueous ionic liquids bear either free phosphate anions or partially esterified phosphate anions as the counterions to the ammonium or phosphonium cations. We generally refer to these new species as LIPs (liquid ionic phosphates). We have developed three approaches toward the syntheses of these materials from the halide salts: one using hexafluorophosphoric acid;; a classical ion exchange method; and treatment with the free phosphorus-containing acid under vacuum. The new LIPs, although highly viscous, exhibit significantly high specific conductivities. Unlike ionic liquids bearing tetrafluoroborate of tetrachloroaluminate anions, the LIPs are unreactive toward water. Further, the LIPs bearing simple phosphate anions are soluble in water, unlike their corresponding hexafluorophosphate salts. We have also examined the UV/Vis, fluorescence, and mobility characteristics of the new LIPs.     

Proton-conducting zirconium phosphate/poly(vinyl acetate)/glycerine gel electrolytes

This work reports on a proton gel electrolyte composed of zirconium phosphate (ZP) particles suspended in a poly(vinyl acetate)/glycerine matrix. The material was studied by X-ray powder diffraction, differential scanning calorimetry, impedance spectroscopy, and spectrophotometry. It had a proton conductivity of 1–0.1 mS/cm at room temperature and remained stable and transparent up to at least 110 °C; it therefore appears suitable for uses in electrochromic devices. The structure of the ZP powder and of the gel is discussed in terms of water removal from interplanar spaces by heating or exfoliation. It is suggested that an exfoliation of the layered structure of ZP by intercalation of glycerine produces a dispersion of ZP nanoparticles in the poly(vinyl acetate)/glycerine matrix.     

Layered zirconium phosphate-supported metalloporphyrin： Synthesis and catalytic application

This paper reports a new route for the preparation of layered alpha-zirconium phosphate （α-ZrP）-supported metalloporphyrin MnTMPyP. MnTMPyP was intercalated into α-ZrP using α-ZrP.BA （i.e. pre-intercalated bultylamine was arranged by a monolayer mode in α-ZrP） as a starting material. The catalytic activity of the supported material for homovanillic acid （HVA） oxidation was investigated. The results showed a promising layered material-supported catalyst in catalytic system.     

Stimuli-responsive properties of N-isopropylacrylamide-based ultrathin hydrogel films prepared by photo-cross-linking

To develop stimuli-responsive ultrathin polymer films on a solid substrate, a novel photo-cross-linkable polymer with both temperature- and pH-responsive properties was prepared. The photoreactive 4-aminobenzophenone (BP) was introduced onto the side groups of poly(N-isopropylaclylamide-co-2-carboxyisopropylaclylamide) [poly(NIPAAm-co-CIPAAm)]. This copolymer was designed for highly random sequences of comonomers. After the formation of spin-coated polymer films on a solid substrate, UV-light irradiation started the cross-linking reaction. The spin-coating processes and stability of the polymer films were quantitatively monitored by a quartz crystal microbalance (QCM), and the thickness was estimated using an atomic force microscope (AFM). These measurements confirmed the formation of a very plain polymer film, and the film thickness was precisely controlled by the concentration of the polymer solution used for spin coating. Moreover, the obtained films showed a high stability due to the cross-liking reaction and UV irradiation. Cyclic voltammetry using potassium ferricyanide revealed that the ions could permeate the photo-cross-linked ultrathin polymer films. The permeability of the ultrathin hydrogel films was dramatically changed by varying the pH and temperature of the aqueous media. These observations suggest that the preparation of isopropylacrylamide-based stimuli-responsive ultrathin hydrogel films is possible.     

Synthesis and characterization of sol-gel zirconium phosphate with template surfactants by different methods

Long chain trimethylammonium salts can be successfully used as guest molecules to produce mesoporous layered materials when intercalated in sol-gel zirconium phosphate, an inorganic ion-exchanger. The obtained materials are very similar independently of the chain length and the synthesis method batch (B) or direct intercalation (DI). They show a good thermal stability, and a very high interlayer distance if compared with their precursor. By the thermal characterization it can be observed that the surfactant is lost in two or three steps depending on its position in the host. The layered structure with the expanded interlayer distance is maintained up to 300°C. From the IR spectra the different surfactant release models for (B) and (DI) are confirmed. This revised version was published online in July 2006 with corrections to the Cover Date.     

Deposition of polyaniline on RVC electrodes: effect of substrate thickness

Polyaniline films, obtained by either chemical or electrochemical deposition on reticulated vitreous carbon (RVC), were investigated as a function of the substrate thickness. The electrochemical properties of these RVC/Pani electrodes were assessed by cyclic voltammetry and electrochemical impedance spectroscopy (EIS), whereas the morphology of the Pani films on RVC was analyzed by scanning electron microscopy (SEM). The cyclic voltammetric results revealed that the oxidation/reduction charges for electrodeposited polyaniline decrease as the RVC thickness is increased. Conversely, the charge densities for the chemically deposited films do not present a significant dependence on the substrate thickness. Two time constants, appearing in all the EIS spectra, indicate that an ohmic drop effect within the RVC substrate affects the polymer electrodeposition and the electrochemical behavior of the obtained electrodes. Therefore, an electric equivalent circuit considering the different electrochemical environments at the outer and inner RVC surfaces was proposed to analyze the EIS data.     

Layer-by-layer deposition of rhenium-containing hyperbranched polymers and fabrication of photovoltaic cells

Multilayer thin films were prepared by the layer-by-layer (LBL) deposition method using a rhenium-containing hyperbranched polymer and poly[2-(3-thienyl)ethoxy-4-butylsulfonate] (PTEBS). The radii of gyration of the hyperbranched polymer in solutions with different salt concentrations were measured by laser light scattering. A significant decrease in molecular size was observed when sodium trifluoromethanesulfonate was used as the electrolyte. The conditions of preparing the multilayer thin films by LBL deposition were studied. The growth of the multilayer films was monitored by absorption spectroscopy and spectroscopic ellipsometry, and the surface morphologies of the resulting films were studied by atomic force microscopy. When the pH of a PTEBS solution was kept at 6 and in the presence of salt, polymer films with maximum thickness were obtained. The multilayer films were also fabricated into photovoltaic cells and their photocurrent responses were measured upon irradiation with simulated air mass (AM) 1.5 solar light. The open-circuit voltage, short-circuit current, fill factor, and power conversion efficiency of the devices were 1.2 V, 27.1 mu A cm(-2), 0.19, and 6.1x10(-3) %, respectively. The high open-circuit voltage was attributed to the difference in the HOMO level of the PTEBS donor and the LUMO level of the hyperbranched polymer acceptor. A plot of incident photon-to-electron conversion efficiency versus wavelength also suggests that the PTEBS/hyperbranched polymer junction is involved in the photosensitization process, in which a maximum was observed at approximately 420 nm. The relatively high capacitance, determined from the measured photocurrent rise and decay profiles, can be attributed to the presence of large counter anions in the polymer film.     

Modifying polymer flocculants for the removal of inorganic phosphate from water

Due to strong hydrogen bonding interactions, thiourea has been shown to have a high affinity for anions such as inorganic phosphate. The interaction between phosphate and thiourea has been used to develop technologies that can detect and even remove phosphate from water. This research investigates the use of thiourea derivatized polymer flocculants for the sequestering of inorganic phosphate from water. The study presented herein describes the development of a thiourea based monomer that was used to create a bi-functional polymer that flocculates suspended solid material as well as sorbs phosphate, removing both from water. The new polymer removed more than 60% of the phosphate from a simulated wastewater sample. The addition of a thiourea trapping group to the polymer more than doubled the amount of phosphate removed from solution compared to control polymers.     

Layered zirconium phosphate chloride dimethyl sulfoxide as a two-dimensional exchanger of anionic ligands. Part I. Substitution of chloride with inorganic monodentate ligands

Crystalline ZrPO(4)Cl(CH(3))(2)SO was prepared by direct precipitation in the presence of oxalic acid as a zirconium complexing agent. The structure of ZrPO(4)Cl(CH(3))(2)SO, refined with the Rietveld method using X-ray powder diffraction data, was confirmed to be close to that of the compound prepared using gamma-zirconium phosphate as a precursor. Chloride anions directly bonded to zirconium were found to act as weak ligands; this made possible their replacement with other monodentate anionic ligands. The preparation and a preliminary characterization of a series of inorganic derivatives obtained by topotactic replacement of Cl with OH, Br, MSO(4) (M = H, NH(4), Na), NaMoO(4), and HCrO(4) anions is reported. The possibility of replacement of chloride also with organic anions, such as alkoxides and carboxylates, and the possibility of substituting also dimethyl sulfoxide with other neutral ligands, as shown by preliminary study, makes ZrPO(4)Cl(CH(3))(2)SO a useful and very flexible precursor for materials chemistry.     

The Influence of Electrolyte Type on Kinetics of Redox Processes in the Polymer Films of Ni(II) Salen-Type Complexes

Electrodes modified with polymers derived from the complexes [Ni(salcn)], [Ni(salcn(Me))] and [Ni(salcn(Bu))] were obtained in order to study the kinetics of electrode processes occurring in polymer films, depending on the thickness of the films, the type of electrolyte and the solvent. FTIR and EQCM methods were used to determine the type of mass transported into polymer films during anode processes and the number of moles of ions and solvent. The rate of charge transport through films was determined by the cyclic voltammetry method, by the quantity cD^1/2. It was shown that the charge transport was determined by the transport of anions. The kinetics were most efficient for poly[Ni(salcn(Bu))] modified electrodes, obtained from TBAPF₆ and working in TBAClO₄ and TBABF₄. It was also shown that a solvent with a higher DN value and lower viscosity (MeCN) facilitated the transport of the charge through polymer films.     

Study of the Properties of Electrodeposited Polypyrrole Films

Experimental and theoretical methods have been used for characterization of the properties of polypyrrole films. The AFM studies show that the morphology of polypyrrole (PPy) films on polycrystalline gold electrodes at the first stages of synthesis depends on the structure of the metal surface. It was established that mobility of anions depends remarkably on the rate of electrodeposition of the polymer film. If PPy film was deposited at relatively low current density, mobility of ClO^- ₄ anion was not high enough to guarantee electroneutrality during redox cycling and cations take part in this process especially when Li⁺ cations were replaced by more mobile ⁺ cations. Semiempirical (AM1 and PM3) quantum-chemical methods were used for theoretical studies. It was established that different size and charge of the anions together with the variation in doping levels give rise to a different optimal conformation of oligopyrrole cations which, in turn, define the resulting polymer to be either all-anti (common linear chains) or all-syn (formation of helical structures) or a combination of the two.     

Study of Polypyrrole/Graphene Oxide Nanocomposite Structural and Morphological Changes Including Porosity

Polypyrrole/graphene oxide (PPy/GO) nanocomposite films were electrochemically synthesized to study their structural features. For this purpose, pyrrole monomer was exposed to oxidation in an aqueous dilute solution containing definite amounts of GO and a dopant electrolyte. Potentiostatic electropolymerization was carried out and the current-time curves were obtained for each electrodeposition test. Accordingly, a number of appropriate characterization analyses such as mercury porosimetry, TGA, SEM, XRD, Raman and FTIR spectroscopies were performed in order to investigate the composition and structure of the films. In this regard, factors such as incorporation of GO in the polymer matrix, porous layer structure and the thickness of the films were determined. The results showed that GO concentration could influence on both film thickness and its porous structure. Also, it was observed that the main factor controlling the film thickness and morphology is the potential applied.     

循环伏安法制聚(1,5-萘二胺)膜及其对紫外可见光吸收的研究

利用循环伏安法合成了1,5-萘二胺(1,5DAN)聚合物膜.从反应的介质、膜的厚度以及掺杂酸的种类等方面,讨论了制备电活性聚1,5-萘二胺(P1,5DAN)膜的影响,结果发现,在酸性水溶液中,初始的电活性比较高,但是,随着循环的继续,聚合物膜的电量损耗比较大,而在乙腈溶液中电量损耗较小;同时还发现,P1,5DAN电活性膜的厚度并不随总电量的增加而增厚;活性聚合物膜是受扩散控制,扩散系数(D)与酸根离子有关.最后,结合电化学,讨论了不同掺杂状态下的紫外可见吸收光谱(UV-Vis),并用FT-IR对所合成的聚合物作了结构表征.     

Preparation of hybrid film of polyaniline and organically pillared zirconium phosphate nanosheet by electrodeposition

α-Zirconium phosphate was chemically modified with 1,2-bis(dimethylchlorosilyl)ethane to graft organic chain, and then it was used as host material for inorganic nanosheet-polyaniline hybrid. The grafted α-zirconium phosphate was exfoliated in an acetonitrile solution with tetrabutylammonium salt and aniline. The electrodeposition in the presence of aniline was performed, and then it resulted in a formation of higher-order structure in which phosphate nanosheet was propped up by 1,2-bis(dimethylchlorosilyl)ethane with intrusion of polyaniline into the nanospace. The gravimetric capacitance of the α-zirconium phosphate without grafts and polyaniline hybrid film was around 194 F/g with the base on the amount of polyaniline mass. On the other hand, the α-zirconium phosphate nanosheet with grafts and polyaniline hybrid film provided larger capacitance of around 350 F/g in maximum. The nanospace formed by grafted phosphate nanosheet with 1,2-bis(dimethylchlorosilyl)ethane molecules gives increased amounts of polyaniline included and diffusion paths for ions.     

Protonolysis of [((i)PrO)TiMo5O18]3-: access to a family of TiMo5 Lindqvist type polyoxometalates

The tetra-n-butylammonium (TBA) salts of [((i)PrO)TiMo(5)O(18)](3-) 1 and [((i)BuO)TiMo(5)O(18)](3-) 2 were prepared by hydrolysis of mixtures of (TBA)(2)[Mo(2)O(7)], (TBA)(4)α-[Mo(8)O(26)] and Ti(OR)(4) (R = (i)Pr or (i)Bu) in acetonitrile. Treatment of (TBA)(3)1 with alcohols ROH afforded primary and tertiary alkoxide derivatives [(RO)TiMo(5)O(18)](3-) (R = Me 3, (t)Bu 4), whilst aryloxides [(ArO)TiMo(5)O(18)](3-) were prepared by reacting 1 with phenols ArOH (Ar = C(6)H(4)Me-4 5, and C(6)H(4)CHO-2 6). Oxo-bridged [(μ-O)(TiMo(5)O(18))(2)](6-)7 rather than the hydroxo derivative [(HO)TiMo(5)O(18)](3-) was obtained upon hydrolysis of 1. X-Ray crystal structures of TBA salts of anions 3-7 show that titanium is six-coordinate in all cases, although titanium sites are disordered over two trans positions in 3. Mo-O bond length alternation is observed in the Mo(4)O(4) planes of 4 and 7 and in one of the two independent anions in the structure of 3. In solution, (17)O NMR spectra are consistent with the higher anionic charge compared to [Mo(6)O(19)](2-) and reveal an order of basicity for the anions [LM'Mo(5)O(18)](3-) associated with the ability of {LM'}(3+) to donate/withdraw electron density from {Mo(5)O(18)}(6-). Protonolysis reactions of 1 and 3 were slower than for tungstate analogues and the possibility of initial protonation at TiOM (M = Mo) rather than TiOR (M = W) in a proton-assisted S(N)1 mechanism for ligand exchange in [(RO)TiM(5)O(18)](3-) is discussed.     

EPR and electronic spectroscopic studies of Keggin type undecatungstophosphocuprate(II) and undecatungstoborocuprate(II)

The coordination of Cu(II) to the Keggin type anions α-undecatungstophosphocuprate(II) and α-undecatungstoborocuprate(II) was investigated in different environments by EPR and electronic spectroscopy. This study has shown that the coordination geometry around Cu(II) in the tetrabutylammonium (TBA) salts, (TBA)₄H_x[XW₁₁CuO₃₉], with X=P or B, is square pyramidal, with copper bound to the five oxygen donor atoms of the polyoxometalate, whereas for the [XW₁₁Cu(H₂O)O₃₉]ⁿ⁻ anion, on the corresponding potassium salt, a tetragonally elongated pseudo-octahedral geometry was found. For the potassium salts, in aqueous solution, six-coordinated copper is the only form found. For the TBA salts, in nonaqueous solvents, we can observe either the presence of only one form (the six-coordinated Cu(II) species, with a solvent molecule bound to copper), or of two forms: the solvent coordinated copper anions and the five-coordinated copper [XW₁₁CuO₃₉]ⁿ⁻ anions.