Thermal investigation of silicone rubber containing imide-siloxane copolymers

Dynamic mechanical thermal analysis and isothermal thermogravimetry yield useful information on the temperature dependence of the mechanical properties and thermal stability of silicone rubbers. In the thermal mechanical relaxation spectra, only one characteristic phenomenon may be observed. Isothermal thermogravimetry reveals that the thermal degradation is a first-order reaction. The experimental results provide a possibility for the calculation of overall (apparent) reaction rate constants characteristic of the thermal decomposition process, and for the calculation of half-time values.     

Detection of compatibility of some rubber blends by DSC

The compatibility of some technically important polymer blends, namely BR/NR, NR/NBR and CR/NBR, has been investigated using the DSC method. In addition, dynamic mechanical measurements have been carried out for the NR/NBR blends over the frequency range of 10^–4 Hz –200 Hz and temperatures ranging from –70 to +70°C.The results obtained show that the three rubber blends are not compatible over the entire composition range as proven by the DSC and mechanical measurements. By analyzing the heat capacity increases at the glass transitions of the separate phases in the NR/BR blend, it was possible to suggest the presence of a limited compatibility at the boundaries of the two phases.By comparing this work with prior measurements, it was possible to conclude that the calorimetric method is a more efficient tool for the study of compatibility of polymer blends when compared to ultrasonic and viscosity methods.Furthermore, it was found that polymers that show compatibility when measured with an ultrasonic method could behave compatible, semicompatible or incompatible when analyzed by DSC. On the other hand, blends that show incompatibility by the ultrasonic method are always incompatible by the DSC method.Dedicated to Professor Wunderlich on the occasion of his 65th birthdayWe are grateful to Prof. Dr. W. Pechhold for stimulating and promoting this work and thanks due to colleagues at the Department of Applied Physics and Section of Calorimetry, Ulm University for their valuable help. Thanks are also extended to Alexander von Humboldt Foundation for supporting the residence of A. A. Yehia in Ulm, which gave the starting impulse to this work. A. Mansour. would like to thank the USAID for supplying the PL-DSC to the Chemistry Dept., Cairo University.     

含CL-20的改性双基推进剂的热行为及非等温反应动力学

用DSC和TG方法研究了含六硝基六氮杂异伍兹烷(CL-20)的改性双基推进剂在常压(0.1 MPa)和高压(4和7 MPa)下的热行为和高压下的热分解反应动力学. 结果表明, 该推进剂常压下DSC曲线有3个放热峰, 相应TG曲线有3个失重过程; 而高压下DSC曲线只有一个放热峰, 高压下放热峰的峰温随加热速率增大而升高. 高压下该推进剂放热分解反应机理和反应动力学参数受测试环境压强影响较弱, 反应机理是随机成核和随后生长, 放热分解反应的动力学方程可以表示为, 4 MPa时, dα/dt=1014.5(1-α)[-ln(1-α)]1/3e-17981.7/T; 7 MPa时, dα/dt=1014.7(1-α)·[-ln(1-α)]1/3e-18138.1/T.     

Ｎ2Ｏ5/HNO3硝化硝解taiw制备CL-20

以2,6,8,12-四乙酰基-2,4,6,8,10,12.六氮杂四环[5,5,0,03,1105,9]十二烷(TAIW)为原料,利用硝化剂N2O5在HNO3介质中硝化硝解TAIW制得CL-20.该方法可避免浓H2SO4污染,最佳反应条件为:反应温度为40℃,反应时间为1 h,n(TAIW):n(N2O5):n(HNO3)=1:4:36,产率为86.1%,纯度达到99%.产物经元素分析、核磁共振、质谱等测试技术对其结构进行了检测和表征.     

Thermal decomposition of silver cyano complex and characterization its decomposition products by ETA,DSC, DTA and TG

It was found by DTA and TG that [Phenyl₂I][Ag(CN)₂] in the solid state is chemically stable on heating in argon up to 160°C. During heating to higher temperatures it decomposes, forming volatile products such as [Phenyl]I, [Phenyl]NC and (CN)₂ [1]. After heating the sample to 500°C metallic silver resulted. The volatile and intermediate solid products were analysed by IR-spectroscopy.It was found by means of DTA and ETA that an isophase reversible transition takes place when the sample is heated and cooled, not higher than 100°C. At heating higher than 100°C the sample melts (melting pointT _m=135°C). The enthalpy melting was determined by means of DSC (H=–28 kJ·mol^–1).By means of ETA the disorder degree of the final decomposition product was estimated. The value of the activation energy of radon diffusion in the temperature range 720°–500°C equals 32.6 kJ·mol^–1.Dedicated to Prof. I. N. Bekman Moscow State University at the occasion of his 50th birthday     

Effects of functional graphene oxide on the properties of phenyl silicone rubber composites

Graphene oxide (GO) was treated with two types of surfactants, i.e., silane coupling agent (KH550) and 4,4’-diphenylmethane diisocyanate (MDI), incorporated into phenyl silicone rubber at a low concentration (≤0.2 wt%), and cured by the room temperature vulcanized method. The effects of functional graphene oxide on the dielectric behaviour, thermal conductivity, optical transmittance and mechanical properties of the composites were investigated. The results showed that the particle size changed after modification and that the modified GO dispersed well in the phenyl silicone rubber. The composites with MDI modified GO exhibited better electrical insulation and lower light loss in the ultraviolet–visible region than the composites with KH550 modified GO. However, composites filled with KH550 modified GO present better thermal conductivity.     

tudy on compatibility of imatinib mesylate with pharmaceutical excipients

Differential scanning calorimetry and thermogravimetric analysis with the support of X-ray powder diffraction and infrared spectroscopy were used as screening techniques for the compatibility testing of imatinib mesylate, with following excipients: magnesium stearate, polyvinylpyrrolidone, microcrystalline cellulose. In order to maximize the probability of interactions 1:1 (by mass) drug: excipient binary mixtures were analysed and compared to individual components. Additionally an influence of storage at temperatures of 25 and 40°C on physico-chemical stability on drug – excipient binary mixtures was investigated. The largest visible changes were observed in the DSC curves of imatinib mesylate – magnesium stearate mixtures.     

Two novel heterobimetallic metal-organic frameworks for the enhanced catalytic thermolysis and laser ignition of CL-20

The study of multiple complex catalytic mechanisms is currently one of the great scientific issues for the application of high-energy solid propellants. Two novel heterobimetallic metal-organic frameworks (MOFs), Ba₄Pb₄(CH₃CO₂)₈ [(CH₆CO₂)₄Pb](CH₃CO₂)₄ (PbBa-MOF) and Ba₂Ni(CO₂H)₆(OH₂)₄ (NiBa-MOF), were prepared via the solvothermal method, and their structures and composition were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), fourier transform infrared spectroscopy (FTIR) techniques and N₂ adsorption/desorption experiment. The thermal decomposition characteristics of the two MOFs and their catalytic performances on the hexanitro hexaazaisowurtzitane (CL-20) thermolysis were also studied by differential scanning calorimetr (DSC) and thermogravimetric-fourier transform infrared spectroscopy-mass spectrum (TG-FTIR-MS) methods. The results showed that the NiBa-MOF presented a lower initial decomposition temperature than the PbBa-MOF, and the difference of the MOFs structures affected the starting point of thermal decomposition. Compared with the pure CL-20, the thermolysis peak temperature and apparent activation energy (E_a) of the CL-20/PbBa-MOF mixture were decreased by 2.2 °C and 23.76 kJ?mol^?1, respectively. The E_a of CL-20/NiBa-MOF mixture was lower and 42.01 kJ?mol^?1, indicating the better catalytic activity of NiBa-MOF. The thermolysis catalytic mechanisms were studied by analyzing the transformation of gas products during the pyrolysis of mixtures. The effect of these two MOFs on the CL-20 thermolysis is primarily owing to the strong attraction of metal cations to electronics, bimetallic synergistic catalysis, and the release of active free radicals. Furthermore, the laser ignition and flame propagation features showed that these two MOFs reduced the minimum ignition power density and ignition delay time of the CL-20, and the flame becomes brighter and more luminous. The influence of the two MOFs on the flame bright spot of CL-20 based mixtures was described.     

Introduction of O-butyrylchitosan with a photosensitive hetero-bifunctional crosslinking reagent to silicone rubber film by radiation grafting and its blood compatibility

Based on an in vitro test for an improvement of the blood compatibility of silicone rubber (SR) films by grafting O-butyrylchitosan (OBCS), OBCS was covalently immobilized onto SR film surface using the photosensitive hetero-bifunctional crosslinking reagent, 4-azidobenzoic acid, which was previously bonded to OBCS by reaction between an acid group of the crosslinking reagent and a free amino group of OBCS. Surface properties of SR film were investigated by attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), electron spectroscopy for chemical analysis (ESCA) and the water contact angle measurements. The blood compatibility of SR film was evaluated by platelet rich plasma (PRP) contacting experiments and the results were observed by scanning electron microscopy (SEM). The state of platelet adhesion was described. The suitable modifications could be carried out to tailor SR films biomaterial to meet the specific needs of different biomedical applications. These results suggest that the blood compatible of SR films/OBCS films show their suitability as potential biomaterials.     

Physico-chemical measurements of CL-20 for environmental applications. Comparison with RDX and HMX

CL-20 is a polycyclic energetic nitramine, which may soon replace the monocyclic nitramines RDX and HMX, because of its superior explosive performance. Therefore, to predict its environmental fate, analytical and physico-chemical data must be made available. An HPLC technique was thus developed to measure CL-20 in soil samples based on the US Environmental Protection Agency method 8330. We found that the soil water content and aging (21 days) had no effect on the recoveries (>92%) of CL-20, provided that the extracts were kept acidic (pH 3). The aqueous solubility of CL-20 was poor (3.6 mg l(-1) at 25 degrees C) and increased with temperature to reach 18.5 mg l(-1) at 60 degrees C. The octanol-water partition coefficient of CL-20 (log KOW = 1.92) was higher than that of RDX (log KOW = 0.90) and HMX (log KOW = 0.16), indicating its higher affinity to organic matter. Finally, CL-20 was found to decompose in non-acidified water upon contact with glass containers to give NO2- (2 equiv.), N2O (2 equiv.), and HCOO- (2 equiv.). The experimental findings suggest that CL-20 should be less persistent in the environment than RDX and HMX.     

Investigation of the hydrothermal stability of cross-linked liquid silicone rubber (LSR)

We investigate the hydrothermal stability of cross-linked liquid silicone rubber (LSR) in water at 100 °C up to period of two years. Optical microscopy of cross-sections of the exposed samples reveal that only the outer 100 μm of the surface layer is affected after two years. However, the surface chemistry of the material after prolonged exposure becomes significantly modified, as monitored by X-ray photoelectron spectroscopy (XPS) and attenuated total reflectance Fourier transform infrared (ATR-FTIR), which probes depths of 10 nm and 1 μm, respectively. In addition, changes to the bulk physical properties of the rubber samples, prior to and after the exposure, were investigated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Micro-hardness analysis showed that surface roughness of the two year exposed sample increased from 60 (IRHD) to 75 (IRHD). Furthermore, the volume change (%) measurement showed a significant decrease in the course of exposure at prolonged time. The results provide the experimental basis for development of LSR materials suitable for numerous technical applications.     

Thermal decomposition and indirect structural determination of rare earth element picrates with the dtso ligand

The complexes [Ln(pic)₃(DTSO)₃] (Ln=La, Lu and Y; pic=picrate; DTSO=1,3-dithiane-1-oxide) were synthesized and characterized. Indirect structural determination by far infrared spectroscopy is presented. Results from thermal decomposition of these complexes by TG/DTG and DSC techniques are reported. This revised version was published online in August 2006 with corrections to the Cover Date.     

Synthesis,characterization of Nafion-functionalized MCM-41 and its catalytic application in preparation of CL-20 via HNO3 electrolyte involved nitration of TAIW

Hybrid organic–inorganic MCM-41 (Mobil Composition of Matter No. 41) silicas functionalized with Nafion (perfluoroalkylsulfonic acid analogous) were prepared and characterized by Fourier Transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and N₂ adsorption analysis. The Brønsted acidity was determined by UV spectrophotometer. The prepared catalyst (SA/MCM-41) exhibited high catalytic activity in the nitration of TAIW (tetraacetylhexaazaisowurtzitan) aiming at synthesizing CL-20 (hexanitrohexaazaisowurtzitane), with the yield up to 93%. The leaching problem was not observed after several runs, demonstrating that the catalyst could be recycled and reused without losing activity.     

Thermal behaviour, compatibility study and decomposition kinetics of glimepiride under isothermal and non-isothermal conditions

In the present work, the thermal decomposition of glimepiride (sulfonylurea hypoglycemic agent) was studied using differential scanning calorimetry (DSC) and thermogravimetry/derivative thermogravimetry (TG/DTG). Isothermal and non-isothermal methods were employed to determine kinetic data of decomposition process. The physical chemical properties and compatibilities of several commonly used pharmaceutical excipients (glycolate starch, microcrystalline cellulose, stearate, lactose and Plasdone®) with glimepiride were evaluated using thermoanalytical methods. The 1:1 physical mixtures of these excipients with glimepiride showed physical interaction of the drug with Mg stearate, lactose and Plasdone®. On the other hand, IR results did not evidence any chemical modifications. From isothermal experiments, activation energy (E _a) can be obtained from slope of lnt vs. 1/T at a constant conversion level. The average value of this energy was 123 kJ mol^–1. For non-isothermal method E _a can be obtained from plot of logarithms of heating rates, as a function of inverse of temperature, resulting a value of 157 and 150 kJ mol^–1, respectively, in air and N₂ atmosphere, from the first stage of thermal decomposition.     

Synthesis of platinum acetylide complexes and their application in curing silicone rubber by hydrosilylation

Eight platinum acetylide complexes have been synthesized and characterized. The catalytic properties of these complexes in curing silicone rubber by hydrosilylation have been tested. Among the complexes tested, trans‐Pt(PPh₃)₂[―C≡CC(CH₃)₂OSi(CH₃)₃] ₂ (2), trans‐Pt(PPh₃)₂[―C≡CC(CH₃)₂OSi(CH₂CH₃)₃]₂ (3), trans‐Pt(PPh₃)₂[―C≡CC(CH₃)₂OSiPh(CH₃)₂]₂ (4), trans‐Pt(PPh₃)₂[―C≡C(C₆H₁₀)OSi(CH₃)₃]₂ (6), trans‐Pt(PPh₃)₂[―C≡C(C₆H₁₀)OSi(CH₂CH₃)₃]₂ (7), and trans‐Pt(PPh₃)₂[―C≡C(C₆H₁₀)OSiPh(CH₃)₂]₂ (8) exhibited sufficiently long pot‐lives (15 days) at room temperature and short silicone rubber curing times of 10–35 min at 100°C or 1–5 min at 120°C. Copyright © 2012 John Wiley & Sons, Ltd.     

水分子对α相CL-20热分解机理影响的分子动力学研究

研究六硝基六氮杂异伍兹烷(CL-20)晶体不同晶型在不同温度下的反应机理, 对于深入认识含能材料在极端条件下的冲击起爆、冲击点火和爆轰过程等具有重要意义. 基于反应力场, 研究水分子在纯α相CL-20及其水合物的晶体结构中数量随时间的变换, 分析水分子对两种体系的初始分解和第二阶段的分解路径的影响. 计算结果表明: CL-20 分子的初始分解路径与水分子无关, 第二阶段的分解反应与水分子有关. 在低温(T<1500 K)下, 水分子对两种体系没有影响, 二者的初始分解路径均为N-NO₂键生成NO₂自由基; 在1500 K≤T≤2500 K时, 水分子作为反应物或与NO₂、、OH自由基等组成催化体系, 生成O₂、H₂O₂等产物, 加速水合物体系在高温下的第二阶段反应, 使得高温下水合物体系的化学反应速率和反应生成的NO₂自由基的数量比纯CL-20体系的化学反应速率和反应生成的NO₂自由基的数量大; 在T>2500 K时, 水分子的催化反应抑制CL-20初始分解反应, 使得在3000 K时纯CL-20体系的反应速率大于水合物体系中CL-20的反应速率.     

Prediction of CL-20 chemical degradation pathways,theoretical and experimental evidence for dependence on competing modes of reaction

Highest occupied and lowest unoccupied molecular orbital energies, formation energies, bond lengths and FTIR spectra all suggest competing CL-20 degradation mechanisms. This second of two studies investigates recalcitrant, toxic, aromatic CL-20 intermediates that absorb from 370 to 430?nm. Our earlier study (Struct. Chem., 15, 2004) revealed that these intermediates were formed at high OH^? concentrations via the chemically preferred pathway of breaking the C–C bond between the two cyclopentanes, thereby eliminating nitro groups, forming conjugated π bonds, and resulting in a pyrazine three-ring aromatic intermediate. In attempting to find and make dominant a more benign CL-20 transformation pathway, this current research validates hydroxylation results from both studies and examines CL-20 transformations via photo-induced free radical reactions. This article discusses CL-20 competing modes of degradation revealed through: computational calculation; UV/VIS and SF spectroscopy following alkaline hydrolysis; and photochemical irradiation to degrade CL-20 and its byproducts at their respective wavelengths of maximum absorption.     

Investigation of photo‐oxidative effect on morphology and degradation of mechanical and physical properties of nano CaCO3 silicone rubber composites

Photo‐oxidative degradation of treated and untreated nano CaCO₃: silicone rubber composite was studied under accelerated UV irradiation (≥290 nm) at different time intervals. Prolonged exposure to UV leads to a progressive decrease in mechanical and physical properties along with the change in behavior of filler‐matrix interaction. This was due to decrease in cross‐linking density with increase in mobility of rubber chains. Meanwhile, synthesized nano CaCO₃ was modified with stearic acid for uniform dispersion in rubber matrix. The increase in carbonyl (>CO), hydroxyl (? OH), CO₂, and alkene functional groups on the UV exposed surface of treated and untreated nano CaCO₃: silicone rubber composites at different time intervals was studied using Fourier transform infrared (FTIR) spectroscopy. The change in morphological behavior of filler‐matrix interaction after UV exposure was studied using SEM. Overall, the study showed that the treated nano CaCO₃: silicone composites were affected more by UV exposure than untreated nano CaCO₃: silicone composites and pristine composite after UV exposure. This effect was due to peeling of stearic acid from the surface of CaCO₃, which makes the rubber chains slippery and thus separation of filler and rubber chains takes place with initiation of fast‐degradation. Copyright © 2011 John Wiley & Sons, Ltd.     

烷基咪唑离子液体CnmimCl(n=4, 6, 8)对CL-20重结晶的影响

六硝基六氮杂异戊兹烷(CL-20)是高能量密度材料的典型代表之一。重结晶制备高品质CL-20的一个重要难题是晶体微观结构的调控。本文通过在CL-20重结晶过程中加入微量离子液体作为晶形控制剂,探究离子液体浓度、种类和添加方式(加入溶剂或者反溶剂)对CL-20晶体微观结构的影响规律。结果表明：通过改变离子液体的添加方式、种类和浓度,能够实现CL-20晶体尺寸和晶体形貌的调控。热分析结果表明：离子液体的加入可以使ε到γ晶型转变温度提前多达12.6℃;重结晶CL-20的分解峰温和热稳定性提高,放热量增加,最高可达1344 J·g^-1。溶剂中1-己基-3-甲基咪唑氯盐(DmimCl)的加入,能够结晶出没有尖锐棱边和角的类八面体形CL-20晶体,晶粒细小,分解峰温均提高了6℃以上,放热量均在1100 J·g^-1以上,是较理想的晶形控制剂。