Preparation of SiO2@polystyrene@polypyrrole sandwich composites and hollow polypyrrole capsules with movable SiO2 spheres inside

In this paper, we describe a flexible method for preparing conducting building blocks: SiO2@polystyrene@polypyrrole sandwich multilayer composites and hollow polypyrrole (PPy) capsules with movable SiO2 spheres inside. First, SiO2@polystyrene (PS) core/shell composites were synthesized, and then SiO2@PS@PPy sandwich multilayer composites were prepared by chemical polymerization of pyrrole monomer on the surface of SiO2@PS composites. Furthermore, hollow polypyrrole capsules with movable SiO2 spheres inside were obtained after removal of the middle PS layer. The diameter of sandwich multilayer composites could easily be controlled by adjusting the dosage of pyrrole monomer. The conductivities of composites increased with the increase of PPy content. After the insulating PS layer was selectively etched, the conductivities of hollow capsules with movable SiO2 spheres inside were much higher than those of the corresponding sandwich multilayer composites.     

壳层可控导电聚吡咯/聚苯乙烯复合微球及聚吡咯中空微胶囊的制备

在导电聚合物含量较小时,含核壳结构的导电聚合物复合粒子就可以具有和本体相当的导电率,且加工性好,近年来这种核壳结构微粒的制备已引起了科学家们的广泛关注．Armes等[制备了导电聚吡咯、导电聚苯胺包覆聚苯乙烯的核壳结构胶体粒子及聚苯胺和二氧化硅的纳米复合物．刘正平等用改进的方法在粒径为116nm的单分散聚苯乙烯乳胶粒子上包覆聚吡咯,     

钛酸四丁酯水解制备聚苯乙烯/二氧化钛核壳粒子及空心二氧化钛微球

通过无皂乳液聚合方法制备了阳离子型及阴离子型聚苯乙烯(PSt)乳胶粒,并对后者用γ-氨丙基三乙氧基硅烷(KH550)进行了表面改性制得了乳胶粒表面载正电荷的乳液.在乙醇与水的混合溶剂中,分别使用以上3种PSt乳胶粒为核加入钛酸四丁酯制备了核壳型PSt/TiO2复合粒子.结果显示,仅在使用经KH550改性的阴离子PSt乳...     

Stable thin films and hollow spheres composing chiral polyaniline composites

Chiral polyaniline composite (CPAC) thin films were fabricated by self-assembly using diazoresin (DR) and CPAC. The weak linkage between the DR and CPAC of the film will convert to covalent bonds under UV irradiation or heating, and the thin film becomes very stable toward polar solvents and electrolyte aqueous solutions. Core-shell particles with stable DR/CPAC shell and polystyrene (PS) core can be prepared by similar methods. After the PS core is removed by chemical etching, stable DR/CPAC hollow spheres were obtained. Circular dichroism spectra and cyclic voltammetry measurements show that the DR/CPAC thin films are chirally active and possess good electrochemical stability.     

Polymerizable Molecular Silsesquioxane Cage Armored Hybrid Microcapsules with In Situ Shell Functionalization

We prepared core–shell polymer–silsesquioxane hybrid microcapsules from cage‐like methacryloxypropyl silsesquioxanes (CMSQs) and styrene (St). The presence of CMSQ can moderately reduce the interfacial tension between St and water and help to emulsify the monomer prior to polymerization. Dynamic light scattering (DLS) and TEM analysis demonstrated that uniform core–shell latex particles were achieved. The polymer latex particles were subsequently transformed into well‐defined hollow nanospheres by removing the polystyrene (PS) core with 1:1 ethanol/cyclohexane. High‐resolution TEM and nitrogen adsorption–desorption analysis showed that the final nanospheres possessed hollow cavities and had porous shells; the pore size was approximately 2–3 nm. The nanospheres exhibited large surface areas (up to 486 m² g^?1) and preferential adsorption, and they demonstrated the highest reported methylene blue adsorption capacity (95.1 mg g^?1). Moreover, the uniform distribution of the methacryloyl moiety on the hollow nanospheres endowed them with more potential properties. These results could provide a new benchmark for preparing hollow microspheres by a facile one‐step template‐free method for various applications.     

金纳米棒@碳中空胶囊的制备及催化性能

以聚吡咯为碳壳前驱体制备了金纳米棒镶嵌于碳壳内的中空胶囊.先合成羧基修饰的聚苯乙烯微球和十六烷基三甲基溴化铵稳定的金纳米棒; 再利用二者之间的静电力将金纳米棒组装在聚苯乙烯微球表面; 最后, 通过氧化聚合将聚吡咯壳包覆在聚苯乙烯@金纳米棒复合物的表面.在氮气保护下经高温煅烧, 聚吡咯壳被碳化为碳壳的同时聚苯乙烯微球分解, 从而制得金纳米棒@碳中空胶囊.在煅烧过程中, 由于碳壳的保护, 金纳米棒很好地保持了“棒状”形貌.通过调节吡咯单体的浓度, 可以控制聚吡咯壳和碳壳的厚度.金纳米棒@碳中空胶囊在以NaBH₄为还原剂还原亚甲基蓝的反应中表现出良好的催化活性.     

Magnetic Fe2O3-polystyrene/PPy core/shell particles: bioreactivity and self-assembly

This paper describes the synthesis of new magnetic, reactive polystyrene/polypyrrole core/shell latex particles. The core consists of a polystyrene microsphere containing gamma-Fe2O3 superparamagnetic nanoparticles (PSmag), and the shell is made of reactive N-carboxylic acid-functionalized polypyrrole (PPyCOOH). These PSmag-PPyCOOH latex particles, average diameter 220 nm, were prepared by copolymerization of pyrrole (Py) and the active carboxyl-functionalized pyrrole (PyCOOH) in the presence of PSmag particles. PNVP was used as a steric stabilizer. The functionalized polypyrrole-coated PSmag particles were characterized in terms of their particle size, surface morphology, chemical composition, and electrochemical and magnetic properties using transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry, and SQUID magnetometry. Activation of the particle surface carboxyl groups was achieved using 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide (EDC) and N-hydroxysuccinimide (NHS), which helps transform the carboxyl groups into activated ester groups (NSE). The activated particles, PSmag-PPyNSE, were further evaluated as bioadsorbents of biotin used as a model biomolecule. It was shown that biotin was immobilized at the surface of the PSmag-PPyNSE particles by forming interfacial amide groups. The assemblies of PSmag-PPyCOOH particles on glass plates were further investigated. When no magnetic field is applied, the particles assemble into 3D colloidal crystals. In contrast, under a magnetic field, one-particle-thick chains gathered in hedgehog-like architectures are obtained. Furthermore, PSmag-PPyCOOH coated ITO electrodes were shown to be electroactive and electrochemically stable, thus offering potentialities for creating novel high-specific-area materials for biosensing devices where the conducting polymer component would act as the transducer through its conductive properties.     

Photochemical preparation of CdS hollow microspheres at room temperature and their use in visible-light photocatalysis

CdS hollow microspheres have been successfully prepared by a photochemical preparation technology at room temperature, using polystyrene latex particles as templates, CdSO₄ as cadmium source and Na₂S₂O₃ as both sulphur source and photo-initiator. The process involved the deposition of CdS nanoparticles on the surface of polystyrene latex particles under the irradiation of an 8 W UV lamp and the subsequent removal of the latex particles by dispersing in dichloromethane. Photochemical reactions at the sphere/solution interface should be responsible for the formation of hollow spheres. The as-prepared products were characterized by X-ray diffraction, transmission electron microscopy and scanning electron microscopy. Such hollow spheres could be used in photocatalysis and showed high photocatalytic activities in photodegradation of methyl blue (MB) in the presence of H₂O₂. The method is green, simple, universal and can be extended to prepare other sulphide and oxide hollow spheres.     

Cagelike polymer microspheres with hollow core/porous shell structures

Submicron‐scaled cagelike polymer microspheres with hollow core/porous shell were synthesized by self‐assembling of sulfonated polystyrene (PS) latex particles at monomer droplets interface. The swelling of the PS latex particles by the oil phase provided a driving force to develop the hollow core. The latex particles also served as porogen that would disengage automatically during polymerization. Influential factors that control the morphology of the microspheres, including the reserving time of emulsions, polymerization rate, and the Hildebrand solubility parameter and polarity of the oil phase, were studied. A variety of monomers were polymerized into microspheres with hollow core/porous shell structure and microspheres with different diameters and pore sizes were obtained. The polymer microspheres were characterized by scanning electron microscopy, transmission electron microscopy, optical microscopy, and Fourier transform infrared spectroscopy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 933–941, 2007     

亚微米级聚苯乙烯/聚硅氧烷核壳粒子的制备及其应用

以乳液聚合制备的聚苯乙烯乳液为种子,加入甲基三甲氧基硅烷(MTMS)水解溶液进行缩聚反应,合成亚微米级聚苯乙烯/聚硅氧烷核壳粒子,并以此作为光散射剂添加至聚甲基丙烯酸甲酯(PMMA)树脂中,制备了光散射材料;考察了亚微米级核壳粒子添加在PMMA树脂中的分散性。结果表明:经过双螺杆剪切作用的挤出加工后,可以实现核壳粒子在PMMA树脂中的良好分散。核壳粒子可以大幅度提高PMMA的雾度,当聚苯乙烯/聚硅氧烷核壳粒子(NS82)的含量为1%时,制得的PMMA样片(厚度为2 mm)的雾度为89%,透光率为69%,有效光散射系数为61%。     

Electrochemical preparation of distinct polyaniline nanostructures by surface charge control of polystyrene nanoparticle templates

A family of nanostructured polyaniline (PANI) materials including polystyrene (PS)/PANI core/shell particles, PANI hollow spheres, PANI/PS nanocomposite and nanoporous PANI, were conveniently prepared by surface charge control of PS nanoparticle templates which resulted in different polymer growth mechanisms when PANI was electropolymerized around the templates.     

Impact modification of thermoplastics by methyl methacrylate and styrene-grafted natural rubber latexes

The preparation and characterization of polymer blends with structured natural rubber (NR)-based latex particles are presented. By a semicontinuous emulsion polymerization process, a natural rubber latex (prevulcanized or not) was coated with a shell of crosslinked polymethylmethacrylate (PMMA) or polystyrene (PS). Furthermore, core–shell latexes based on a natural rubber/crosslinked PS latex semi-interpenetrating network were synthesized in a batch process. These structured particles were incorporated as impact modifiers into a brittle polymer matrix using a Werner & Pfleiderer twin screw extruder. The mechanical properties of PS and PMMA blends with a series of the prepared latexes were investigated. In the case of PMMA blends, relatively simple core (NR)–shell (crosslinked PMMA) particles improved the mechanical properties of PMMA most effectively. An intermediate PS layer between the core and the shell or a natural rubber core with PS subinclusions allowed the E-modulus to be adjusted. The situation was different with the PS blends. Only core–shell particles based on NR-crosslinked PS latex semi-interpenetrating networks could effectively toughen PS. It appears that microdomains in the rubber phase allowed a modification of the crazing behavior. These inclusions were observed inside the NR particles by transmission electron microscopy. Transmission electron photomicrographs of PS and PMMA blends also revealed intact and well-dispersed particles. Scanning electron microscopy of fracture surfaces allowed us to distinguish PS blends reinforced with latex semi-interpenetrating network-based particles from blends with all other types of particles.     

Facile preparation of monodisperse hollow cross‐linked chitosan microspheres

We have successfully prepared biocompatible and biodegradable hollow microspheres using carboxyl‐functionalized polystyrene particles as core template and the chitosan cross‐linked with glutaraldehyde as the shell. The monodisperse carboxyl‐functionalized polystyrene particles were made by emulsifier‐free emulsion polymerization. The structure, morphology, and constitution of the carboxyl‐functionalized polystyrene particles were characterized by FTIR, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X‐ray photoelectron spectroscopy (XPS). The structure, morphology, and formation process of the hollow cross‐linked chitosan microspheres were characterized by FTIR, SEM, and TEM. The results revealed that the latex particles were removed by exposed to solvent and the microspheres exhibited the hollow structure. This work confirmed that the hollow microspheres were accomplished by fabricating on the basis of chemical cross‐linking on the surface of the carboxyl‐functionalized polystyrene particles and then removing off the cores of particles. Moreover, with the increase of carboxyl‐functionalization degree at the surface of latexes and the increase of cross‐linking period, the thicker and firmer monodisperse hollow microspheres were obtained. In addition, a water‐soluble drug, salicylic acid, encapsulated in the microcapsules slowly released at pH 1.2. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 228–237, 2008     

Preparation and characterization of core-shell polystyrene/polychloromethylstyrene and hollow polychloromethylstyrene micrometer-sized particles of narrow-size distribution

Polystyrene core microspheres of narrow-size distribution were prepared by dispersion polymerization of styrene in a mixture of ethanol and 2-methoxy ethanol. Polystyrene/polychloromethylstyrene and polystyrene/poly(chloromethylstyrene-divinylbenzene) core-shell microspheres of narrow-size distribution were prepared by seeded emulsion polymerization of chloromethylstyrene or chloromethylstyrene and divinylbenzene in the presence of the polystyrene core microspheres at 71 °C. Core-shell particles with different properties (size, surface morphology, and composition) have been prepared by changing various parameters belonging to the emulsion polymerization process, e.g., volume of the chloromethylstyrene and the volume ratio of chloromethylstyrene to divinylbenzene. Dissolution of the polystyrene core of the polystyrene/poly(chloromethylstyrene-divinylbenzene) core-shell particles resulted in the formation of crosslinked hollow polychloromethylstyrene microspheres, broken crosslinked polychloromethylstyrene shells, or particles containing voids, depending on the composition of the polystyrene/poly(chloromethylstyrene-divinylbenzene) particles.     

Micelles of poly(styrene-b-2-vinylpyridine-b-ethylene oxide) with blended polystyrene core and their application to the synthesis of hollow silica nanospheres

Core-shell-corona (CSC) micelles of asymmetric triblock copolymer, poly(styrene-b-2-vinylpyridine-b-ethylene oxide) (PS-PVP-PEO), containing polystyrene homopolymer (homo-PS) in the core were successfully prepared in aqueous media. The influence of homo-PS contents over the formation of the micelles was investigated thoroughly by various techniques such as dynamic light scattering (DLS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and fluorescence spectroscopy. It was found that the size of the PS core of the micelle was increased by the addition of homo-PS as observed by DLS and TEM techniques. The SEM and TEM measurements confirm the spherical morphology of the micelles and enlargement of PS core over the addition of homo-PS. The increase in the PS core volume of the PS-PVP-PEO micelles is attributed to the insertion of homo-PS in the PS core. The micelles have also been demonstrated as facile soft templates for synthesis of hollow silica nanospheres. The average diameter of the spherical hollow particles could be tuned between 30.6 and 38.8 nm with cavity sizes ranging from 20.7 to 28.5 nm using tetramethoxysilane as silica precursors under mild acidic conditions. The facile synthesis of hollow silica using the CSC micelles with different homo-PS contents indicates that the hollow void size can be controlled within a range of several nanometers.     

Is latex surface charge an important parameter for foam stabilization?

We describe the facile production of highly stable foams stabilized solely by cationic polystyrene latex particles. Three model polystyrene latexes were synthesized using either a cationic 2,2'-azobis(2-diisobutyramidine) dihydrochloride (AIBA) or an anionic ammonium persulfate (APS) radical initiator: a 724 +/- 81 nm charge-stabilized cationic polystyrene latex [AIBA-PS], an 800 +/- 138 nm sterically stabilized cationic latex prepared using a poly(ethylene glycol) monomethacrylate macromonomer [PEGMA-AIBA-PS], and a 904 +/- 131 nm charge-stabilized anionic polystyrene latex [APS-PS], respectively. The effect of particle surface charge, latex concentration, and solution pH on foam stability was studied in detail. The PEGMA-AIBA-PS latex proved to be the best foam stabilizer even at relatively low latex concentrations (3.0 wt %), with long-term foam stabilities being obtained after drying. The AIBA-PS latex also produced stable foams, albeit only at higher latex concentrations. However, the APS-PS latex proved to be an ineffective foam stabilizer. This is believed to be primarily due to the anionic surface character of this latter latex, which prevents its adsorption at the anionic air-water interface. This hypothesis is supported by the observation that the AIBA-PS latex no longer acts as an effective foam stabilizer above its isoelectric point (pH 7.04). Scanning electron microscopy studies revealed the formation of well-defined latex bilayers within dried foams, which indicates that the wet air bubbles are stabilized by latex monolayers prior to drying. However, little or no long-range ordering of the latex particles was observed on the surface of the bubbles, which is presumably related to the latex polydispersity.     

Sustained release control via photo-cross-linking of polyelectrolyte layer-by-layer hollow capsules

We describe the formation and permeability of polyelectrolyte multilayer hollow-shell capsules by photo-cross-linking and controlled-release (fluorescence) studies. The hollow shells were prepared by alternate layer-by-layer (LbL) adsorption of photo-cross-linkable benzophenone modified poly(allylamine hydrochloride) and poly(sodium 4-styrenesulfonate) on polystyrene particles, followed by removing the core with tetrahydrofuran. Zeta potential measurements, fourier transform infrared spectroscopy, and transmission electron microscopy were used to verify the LbL process integrity. A model drug, rhodamine B (RB), was successfully loaded into the polyelectrolyte hollow capsules. The release kinetics of RB was investigated using fluorescence spectroscopy. The permeability of RB through the hollow shells was effectively controlled based on UV irradiation time. It was shown that the release of RB molecules can be controlled by the degree of cross-linking induced in the multilayer.     

Highly stable and biocompatible nafion-based capsules with controlled permeability for low-molecular-weight species

Biocompatible hollow capsules have been formed by electrostatic layer-by-layer self-assembly of a perfluorinated ionomer (Nafion) in alternation with ferric ions onto polystyrene latex particles or organic microcrystals, followed by dissolution of the cores by tetrahydrofuran or dimethylformamide. The stepwise growth of multilayers was followed by UV-visible spectroscopy and microelectrophoresis. The formation of hollow capsules was verified by confocal laser scanning microscopy and scanning force microscopy. The hollow Fe3+/Nafion capsules displayed high stability over a wide range of pH values and at high temperature. Fluorescein transport through the Fe3+/Nafion capsule wall was studied by means of photochemical bleaching and recovery (PBR) of the capsule interior. A diffusion model is suggested to calculate the diffusion coefficient for low-molecular-weight species, which was determined to be in the order of 10(-12) cm2s. The permeability can be manipulated by changing the wall thickness of the capsules.     

侧链偶氮聚电解质在胶体微球表面的静电层层自组装和微胶囊制作

将侧链偶氮聚电解质应用于聚苯乙烯胶体微球表面的静电层层自组装,得到了偶氮聚电解质和聚二烯丙基二甲基氯化铵多层膜覆盖的核壳微球.实验表明,组装后偶氮苯基团发生了一定程度的解聚集,得到的胶体微球可表现出明显的光色效应.研究进一步采用含肉桂酸酯的光敏聚电解质作为交联的保护壳层,并通过光交联反应使表面层发生交联固化反应.将上述具有核壳结构的胶体球溶解去除聚苯乙烯内核后,得到了含光响应聚电解质的空心微胶囊.     

Dual latex/surfactant templating of hollow spherical silica particles with ordered mesoporous shells

Hollow spherical silica particles with hexagonally ordered mesoporous shells are synthesized with the dual use of cetyltrimethylammonium bromide (CTAB) and unmodified polystyrene latex microspheres as templates in concentrated aqueous ammonia. In most of the hollow mesoporous particles, cylindrical pores run parallel to the hollow core due to interactions of CTAB/silica aggregates with the latices. Effects on the product structure of the CTAB:latex ratio, the amount of aqueous ammonia, and the latex size are studied. Hollow particles with hexagonally patterned mesoporous shells are obtained at moderate CTAB:latex ratios. Too little CTAB causes silica shell growth without surfactant templating, and too much induces nucleation of new mesoporous silica particles without latex cores. The concentration of ammonia must be large to induce co-assembly of CTAB, silica, and latex into dispersed particles. The results are consistent with the formation of particles by addition of CTAB/silica aggregates to the surface of latex microspheres. When the size and number density of the latex microspheres are changed, the size of the hollow core and the shell thickness can be controlled. However, if the microspheres are too small (50 nm in this case), agglomerated particles with many hollow voids are obtained, most likely due to colloidal instability.