PANI Conductivity: A Dependence of the Chemical Synthesis Temperature

Summary: This work evaluated the influence of the synthesis temperature on the polyaniline (PANI) properties obtained by in-situ polymerization onto a poly (terephthalate) (PET) substrate. The residual mass of these syntheses was dried under vacuum, obtaining PANI powders for each temperature investigated. PANI/PET thin films and PANI powders were characterized by atomic force microscopy (AFM), field emission scanning electron microscopy (FEG-SEM), X-ray diffraction (XRD), ultraviolet-visible spectroscopy (UV-Vis) and four-point probe techniques. The UV-Vis results showed that the synthesized PANI presents the emeraldine oxidation state. By means of XRD technique, it was possible to verify that the PANI powders present crystalline form. The AFM and FEG-SEM techniques showed that the decrease in PANI/PET and PANI powders electrical conductivity with increasing of the synthesis temperature is related to the polymeric aggregates morphology.     

A comparative study of the polyaniline thin films produced by the cluster beam deposition and laser ablation methods

Polyaniline (PANI) thin films have been prepared by applying the novel neutral and ionized cluster beam deposition (NCBD and ICBD) methods and the pulsed laser deposition (PLD) technique to the PANI samples of half-oxidized emeraldine base (EB-PANI) and protoemeraldine base forms in a high-vacuum condition. Characterization of the oxidation states and structural changes of pristine and doped thin films has been performed by Fourier transform infrared spectroscopy, ultraviolet-visible spectroscopy, and x-ray photoelectron spectroscopy. Spectroscopic measurements demonstrate that the dominant structure of NCBD and ICBD thin films corresponds to the reduced leucoemeraldine base state, whereas the chemical composition of PLD thin films depends critically on the laser fluence and the molecular weight of PANI target. The congruent deposition is only obtained for the PLD films deposited by the laser-induced decomposition of the low-molecular-weight targets in the low to intermediate fluence regime (below 100 mJ/cm2 with a pulse duration of 7 ns). The surface morphology examined by atomic force microscopy measurements shows that the cluster and laser beams are effective in producing smooth, uniform polymeric thin films. After I2 and HCl doping, the electrical conductivities of the NCBD, ICBD, and particularly PLD thin films are increased significantly. The higher conductivity of PLD films is ascribed to higher amounts of quinoid di-imine doping sites in the EB-PANI state, and the overall structure-conductivity characteristics are consistent with the spectroscopic observations.     

Formation of polyaniline/Pt nanoparticle composite films and their electrocatalytic properties

Polyaniline (PANI) thin films modified with platinum nanoparticles have been prepared by several methods, characterised and assessed in terms of electrocatalytic properties. These composite materials have been prepared by the in situ reduction of a platinum salt (K₂PtCl₄) by PANI, in a variety of solvents, resulting in the formation of platinum nanoparticles and clusters of different sizes. The further deposition of platinum clusters at spin cast thin films of PANI/Pt composites from a neutral aqueous solution of K₂PtCl₄ has also been demonstrated. Thin-film electrodes prepared from these materials have been investigated for their electrocatalytic activity by studying hydrazine oxidation and dichromate reduction. The properties of the composite materials have been determined using UV–visible spectroscopy, atomic force microscopy and transmission electron microscopy. The nature of the material formed is strongly dependent on the solvent used to dissolve PANI, the method of preparation of the PANI/Pt solution and the composition of the spin cast thin film before subsequent deposition of platinum from the aqueous solution of K₂PtCl₄.Dedicated to Professor Dr. Alan Bond on the occasion of his 60th birthday.     

Development and application of patterned conducting polymer thin films as chemoresponsive and electrochemically responsive optical diffraction gratings

We describe the preparation of two-dimensionally patterned polyaniline (PANI) thin films via microtransfer molding and electropolymerization techniques. This procedure yields reproducible conducting polymer patterns with excellent feature periodicity, making them useful as diffraction gratings. The fabricated polymer gratings were characterized via tapping-mode atomic force microscopy. Spectroelectrochemistry was used to characterize the optical properties associated with various intrinsic PANI redox states. In accordance with the Kramers–Kronig relation for change-in-absorptivity and change-in-index-of-refraction, electrochemically induced changes in refractive index (detected via changes in diffraction efficiency) were observed to coincide with electrochemically-induced changes in the PANI electronic absorption spectrum. In addition, the higher oxidation states of PANI and the associated changes in refractive index proved accessible via chemical oxidation. Beyond the novelty of a chemically-switchable transmission grating, the response of this system points to the possibility of developing diffraction-based chemical sensing schemes.     

Enhanced Thermoelectric Properties of Polyaniline Nanofilms Induced by Self‐Assembled Supramolecules

Polyaniline (PANI) is one of the most promising candidates for flexible organic thermoelectric (TE) applications owing to its relatively low cost and high stability. Herein, the self‐assembled supramolecule (SAS) (3,6‐dioctyldecyloxy‐1,4‐benzenedicarboxylic acid) was used as an additive and was introduced into PANI films as a template. Raman spectroscopy, X‐ray diffraction, and conductive atomic force microscopy analyses demonstrated that the highly ordered chain structure of PANI was achieved by chemical interactions between PANI and the SAS. Moreover, the ordered regions in the PANI‐SAS film increased with a decrease in the film thickness. Consequently, the TE properties of PANI‐SAS films were not only much higher than those of PANI films, but they also increased with a decrease in film thickness. The maximum TE power factor of the PANI‐SAS film reached 31 μW m^?1 K^?2, which is approximately six times higher than the power factor of a PANI film with a similar thickness. This work offers a promising way to prepare PANI thin films with enhanced TE properties.     

Well-dispersed multi-walled carbon nanotube/polyaniline composite films

Multi-walled carbon nanotube (MWNT)/polyaniline (PANI) composite films with good uniformity and dispersion were prepared by electrochemical polymerization of aniline containing well-dispersed MWNTs. The results of transmission electron microscopy (TEM) show that aniline can be used to solve MWNTs via formation of donor–acceptor complexes. Scanning electron microscopy (SEM), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) revealed that the well arrangement of PANI-coated MWNTs in these films facilitated improved electron and ion transfer relative to pure PANI films and this may be due to the strong interaction between MWNTs and PANI.     

Selective Formation of Polyaniline Confined in the Nanopores of a Metal–Organic Framework for Supercapacitors

In this study, a strategy that can result in the polyaniline (PANI) solely confined within the nanopores of a metal–organic framework (MOF) without forming obvious bulk PANI between MOF crystals is developed. A water-stable zirconium-based MOF, UiO-66-NH₂, is selected as the MOF material. The polymerization of aniline is initiated in the acidic suspension of UiO-66-NH₂ nanocrystals in the presence of excess poly(sodium 4-styrenesulfonate) (PSS). Since the pore size of UiO-66-NH₂ is too small to enable the insertion of the bulky PSS, the quick formation of pore-confined solid PANI and the slower formation of well dispersed PANI:PSS occur within the MOF crystals and in the bulk solution, respectively. By taking advantage of the resulting homogeneous PANI:PSS polymer solution, the bulk PANI:PSS can be removed from the PANI/UiO-66-NH₂ solid by successive washing the sample with fresh acidic solutions through centrifugation. As this is the first time reporting the PANI solely confined in the pores of a MOF, as a demonstration, the obtained PANI/UiO-66-NH₂ composite material is applied as the electrode material for supercapacitors. The PANI/UiO-66-NH₂ thin films exhibit a pseudocapacitive electrochemical characteristic, and their resulting electrochemical activity and charge-storage capacities are remarkably higher than those of the bulk PANI thin films.     

Effects of polymerization media on the nanoscale conductivity and current-voltage characteristics of chemically synthesized polyaniline films

A current sensing atomic force microscope (CS-AFM) was used to probe the conducting homogeneity and band structures of fully doped polyaniline (PANI) films prepared from in situ chemical polymerization/deposition of aniline on indium tin oxide in various inorganic acids. The charge transport properties of PANI films depend on the film thickness as well as polymerization medium. Fluctuations in conductivity are observed on all acid-doped PANI films and the conducting homogeneity was dependent on the film thickness: the conductivity of thick film is more uniform. The current-voltage (I-V) characteristics of all thick (>200 nm) films displayed a metal-like behavior and conductivity as high as 40 S/cm was detected in high conducting regions of film thicker than 400 nm. Whereas thin (<120 nm) films revealed insulating, semiconducting, and semimetal conducting, wide distribution in conductivity and interband distances (estimated from the I-V ordI/dV-V curves) was found. The interband distances is 0-1.35, 0-1.0, and 0-0.78 eV for thin PANI film prepared from HCl(aq), HClO(4)(aq), and H2SO4(aq), respectively. PANI film (260 nm) prepared from H2SO4(aq) revealed fiberlike morphology, and compared to PANI films prepared from HCl(aq) and HClO4(aq) with similar thickness, it has higher average nanoscale conductivity but lower bulk conductivity. This result could be direct evidence which supports that the bulk conductivity of PANI depended on the carriers hopping between the conducting domains.     

Polyaniline nanostructure electrode: morphological control by a hybrid template

Journal of Solid State Electrochemistry - We report here a novel approach to the template-assisted electrochemical synthesis of vertically aligned polyaniline (PANI) nanostructure surface arrays....     

Development of an optical ammonia sensor based on polyaniline/epoxy resin (SU-8) composite

Polyaniline (PANI)/glycidyl ether of bisphenol A (SU-8) composite film is elaborated in order to detect ammonia gas. These composite films are characterized by ultraviolet-visible (UV-vis) spectroscopy, Fourier transformed infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). The sensitivity to ammonia is measured by optical absorption changes. The ammonia sensing properties of PANI/SU-8 composite films are studied, and then are compared to pure PANI films elaborated by chemical way. Experimental results show that the PANI/SU-8 optical sensor has simultaneously a rapid response to ammonia gas and regenerates easily, that is advantageous compared to pure PANI films.     

Two liquid adsorptive entrapment of a pluronic polymer into the surface of polyaniline films

Pluronic triblock copolymers were entrapped on the surface of polyaniline (PANI) films by first immersing the latter in N-methylpyrrolidinone (NMP) solutions of one of the Pluronics for a short time. This softened the surface of the films and allowed the Pluronic molecules to entangle with PANI segments of the swollen film on the surface. Further, the films were taken out from the NMP solution and dipped into water, which is a nonsolvent for PANI. The rapid surface deswelling of PANI by the water resulted in the entrapment of the Pluronic on its surface, with the hydrophilic blocks toward water and the hydrophobic block imbedded in the PANI films. The modified PANI obtained was examined by X-ray photoelectron spectroscopy, water droplets contact angles, scanning electron microscopy, and wide angle X-ray diffraction. The surface of the Pluronic entrapped PANI films became more hydrophilic than the hydrophobic PANI films and decreased the amount of bovine serum albumin protein adsorbed on them. This means that, by reducing the biofouling, the life of the modified polyaniline film can be extended when the latter is employed as a biosensor.     

The Electrochemical Properties of Nanocomposite Films Obtained by Chemical In Situ Polymerization of Aniline and Carbon Nanostructures

Interactions between the π bonds in the aromatic rings of polyaniline (PANI) with carbon nanostructures (CNs) facilitate charge transfer between the two components. Different types of phenyleneamine‐terminated CNs, including carbon nano‐onions (CNOs) and single‐walled and multi‐walled carbon nanotubes (SWNTs and MWNTs, respectively), were prepared as templates, and the CN/PANI nanocomposites were easily prepared with uniform core–shell structures. By varying the ratio of the aniline monomers relative to the CNs in the in situ chemical polymerization process, the thickness of the PANI layers was effectively controlled. The morphological and electrical properties of the nanocomposite were determined and compared. The thickness and structure of the PANI films on the CNs were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), and infrared spectroscopy. TEM and SEM revealed that the composite films consisted of nanoporous networks of CNs coated with polymeric aniline. The electrochemical properties of the composites were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. These studies showed that the CN/PANI composite films had lower resistance than pure polymeric films of PANI, and the presence of CNs much improved the mechanical stability. The specific electrochemical capacitance of the CNO/PANI composite films was significantly larger than for pure PANI.     

单分散P(St-BA-AN)/PANI核壳结构复合微球的制备与电性能

以苯乙烯(St)、丙烯酸丁酯(BA)和丙烯腈(AN)为单体, 采用乳液聚合的方法制备出单分散苯乙烯-丙烯酸丁酯-丙烯腈三元共聚物[P(St-BA-AN)]种子微球, 再在该种子微球表面包覆聚苯胺(PANI), 制得P(St-BA-AN)/PANI核壳结构复合微球. 采用扫描电镜(SEM)、透射电镜(TEM)、傅里叶变换红外透射光谱(FTIR)和漫反射光谱等测试手段对所制备的种子微球和复合微球的形态、结构和形成机理进行了研究, 并用四探针法测定了核壳结构复合物的导电性. 研究结果表明, 通过改变种子乳液共聚物的组成和加入苯胺的量及氧化剂的量等条件可调控复合微球的电导率. 与P(St-BA)/PANI核壳结构复合微球相比, 在核组成中引入了氰基的P(St-BA-AN)/PANI核壳结构复合微球的电导率明显提高, 当加入苯胺的量为P(St-BA-AN)种子微球与苯胺单体总质量分数的40%时, 其电导率可达到0.71 S/cm. 红外光谱结果证实了P(St-BA-AN)种子微球中的氰基和壳层中聚苯胺的胺基之间存在某种相互作用, 导致核壳结构复合物电导率的提高.     

Investigations on silver/polyaniline electrodes for electrochemical supercapacitors

Polyaniline (PANI) and silver doped polyaniline (Ag/PANI) thin films were deposited on stainless steel substrates by a dip coating technique. To study the effect of doping concentration of Ag on the specific capacitance of PANI the concentration of Ag was varied from 0.3 to 1.2 weight percent. Fourier transform-infrared and Fourier transform-Raman spectroscopy, and energy dispersion X-ray techniques were used for the phase identification and determination of the doping content in the PANI films, respectively. The surface morphology of the films was examined by Field Emission Scanning Electron Microscopy, which revealed a nanofiber like structure for PANI and nanofibers with bright spots of Ag particles for the Ag/PANI films. There was decrease in the room temperature electrical resistivity of the Ag/PANI films of the order of 10(2) with increasing Ag concentration. The supercapacitive behavior of the electrodes was tested in a three electrode system using 1.0 M H(2)SO(4) electrolyte. The specific capacitance increased from 285 F g(-1) (for PANI) to 512 F g(-1) for Ag/PANI at 0.9 weight percent doping of Ag, owing to the synergic effect of PANI and silver nanoparticles. This work demonstrates a simple strategy of improving the specific capacitance of polymer electrodes and may also be easily adopted for other dopants.     

Effect of matrix domination in PANI interpolymer complexes with polyamidosulfonic acids

Various polyaniline (PANI) interpolymer complexes with polyacids in the form of molecular solutions were synthesized by chemical oxidative polymerization of aniline in the presence of water-soluble poly-(2-acrylamido-2-methyl-1-propanesulfonic acid) (flexible backbone), poly-p,p′-(2,2′-disulfoacid)-diphenylene-terephthalamide (t-PASA, rigid backbone), and their mixtures in different ratios. The complexes were characterized by UV-Vis-near infrared spectroscopy in solutions; also, the films’ drop-casts from these solutions were investigated by cyclic voltammetry, spectroelectrochemical, direct current (DC) conductivity, and atomic force microscopy (AFM) measurements. It was shown that the nature of polyacid affects the shape of spectra and the dynamics of their changes. The character of spectral changes during the matrix synthesis of PANI in the presence of mixtures of the rigid-chain and flexible-chain matrixes and the study of spectral properties of the obtained PANI solutions demonstrates the existence of the rigid-matrix domination effect in the process of formation of PANI interpolymer complexes. Spectral properties of the obtained PANI complexes with the mixtures of flexible-chain and rigid-chain polyacids of different ratios (3:1, 1:1, 1:3, and 1:6) are very similar to those ones for the complex with rigid-chain t-PASA. At the same time, there is a correlation between the electrical conductivity and morphology of the films of PANI complexes and their composition, the conductivity passing through a minimum for the complexes with the polyacid mixtures (6:1, 3:1, and 1:1).     

Polyaniline-coated carbon particles and their electrode behavior in organic carbonate electrolyte

In an attempt to increase the interface stability of carbon used in Li-ion batteries, a thin conducting polyaniline (PANI) film was fabricated on the surface of carbon by in situ chemical polymerization. The chemical and electrochemical properties of the composite material were characterized using X-ray diffraction, Raman spectroscopy, scanning electron microscope, cyclic voltammetry, and electrochemical impedance spectroscopy. It was confirmed that the PANI film has an obvious effect on the morphology and the electrochemical performance of carbon. The results could be attributed to the electronic and electrochemical activity of the conducting PANI films.     

Controllable deposition of a platinum nanoparticle ensemble on a polyaniline/graphene hybrid as a novel electrode material for electrochemical sensing

We demonstrate for the first time an interfacial polymerization method for the synthesis of high-quality polyaniline-modified graphene nanosheets (PANI/GNs), which represents a novel type of graphene/polymer heterostructure. The interfacial polymerization at a liquid-liquid interface allows PANI to grow uniformly on the surface of the GNs. An ultra-high loading of Pt nanoparticles was then controllably deposited on the surface of the PANI/GNs to form a Pt/PANI/GNs hybrid. The obtained composites were characterized by scanning electron microscopy, transmission electron microscopy, energy-dispersive spectrometry, X-ray diffraction, X-ray photoelectron spectroscopy, and thermogravimetric analysis. The Pt/PANI/GNs hybrid shows excellent electrocatalytic activity toward methanol oxidation and oxygen reduction. H(2)O(2) and glucose were used as two representative analytes to demonstrate the sensing performance of a Pt/PANI/GNs-modified electrode. It is found that this sensing element shows high sensitivity and a low detection limit for H(2)O(2) and glucose. The results demonstrate that the Pt/PANI/GNs hybrid may be an attractive and advanced electrode material with potential applications in the construction of electrochemical sensors and biosensors.     

Ag+掺杂聚苯胺的制备及其电容特性研究

以苯胺为单体,采用界面聚合法合成了不同浓度的Ag⁺掺杂的聚苯胺(PANI/Ag⁺),使用傅里叶变换红外光谱（FT-IR）、X射线衍射（XRD）和场发射扫描电镜（SEM）等手段对其结构和形貌进行了分析和表征. 在0.5 mol•L^-1 Na₂SO₄电解液中,通过循环伏安（CV）、恒流充放电（CP）以及电化学阻抗（EIS）等技术研究了其电化学性能. 结果表明,当电流密度为5 mA•cm^-2时,PANI/0.12mol•L^-1 Ag⁺的比电容达529 F•g^-1,循环1000次后比电容保持51%,相对于无Ag⁺掺杂的PANI,表现出更优良的电化学电容特性.     

恒电位脉冲法制备聚苯胺薄膜及其表征

采用恒电位脉冲法制备聚苯胺薄膜, 利用扫描电子显微镜(SEM)、红外光谱(IR)、X射线衍射(XRD)及荧光光谱对所制备的薄膜进行比较与表征. 分别考察了循环周期、占空比及脉冲时间对薄膜形貌的影响. SEM形貌分析结果表明, 随着占空比的减小, 聚苯胺薄膜表面颗粒细化; 随循环周期的增加, 聚苯胺薄膜由片层结构转变为纵向生长的颗粒状结构. 荧光光谱分析结果表明, 聚苯胺薄膜具有光致发光性能, 发射峰位置约520 nm, 且发光强度随占空比的增大而增强. 电化学性能测试结果表明, 恒电位脉冲电位法制备的聚苯胺薄膜具有良好的电容特性.     

Nanofibrous polyaniline thin film prepared by plasma‐induced polymerization technique for detection of NO2 gas

A nanofibrous polyaniline (PANI) thin film was fabricated using plasma‐induced polymerization method and explored its application in the fabrication of NO₂ gas sensor. The effects of substrate position, pressure, and the number of plasma pulses on the PANI film growth rate were monitored and an optimum condition for the PANI thin film preparation was established. The resulting PANI film was characterized with UV–visible spectrophotometer, FTIR, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The PANI thin film possessed nanofibers with a diameter ranging from 15 to 20 nm. The NO₂ gas sensing behavior was studied by measuring the change in electrical conductivity of PANI film with respect to NO₂ gas concentration and exposure time. The optimized sensor exhibited a sensitivity factor of 206 with a response time of 23 sec. The NO₂ gas sensor using nanofibrous PANI thin film as sensing probe showed a linear current response to the NO₂ gas concentration in the range of 10–100 ppm. Copyright © 2009 John Wiley & Sons, Ltd.