Effects of current densities on the formation of LiCoO<Subscript>2</Subscript>/graphite lithium ion battery

The activation characteristics and the effects of current densities on the formation of a separate LiCoO₂ and graphite electrode were investigated and the behavior also was compared with that of the full LiCoO₂/graphite batteries using various electrochemical techniques. The results showed that the formation current densities obviously influenced the electrochemical impedance spectrum of Li/graphite, LiCoO₂/Li, and LiCoO₂/graphite cells. The electrolyte was reduced on the surface of graphite anode between 2.5 and 3.6 V to form a preliminary solid electrolyte interphase (SEI) film of anode during the formation of the LiCoO₂/graphite batteries. The electrolyte was oxidized from 3.95 V vs Li⁺/Li on the surface of LiCoO₂ to form a SEI film of cathode. A highly conducting SEI film could be formed gradually on the surface of graphite anode, whereas the SEI film of LiCoO₂ cathode had high resistance. The LiCoO₂ cathode could be activated completely at the first cycle, while the activation of the graphite anode needed several cycles. The columbic efficiency of the first cycle increased, but that of the second decreased with the increase in the formation current of LiCoO₂/graphite batteries. The formation current influenced the cycling performance of batteries, especially the high-temperature cycling performance. Therefore, the batteries should be activated with proper current densities to ensure an excellent formation of SEI film on the anode surface.     

Kinetics of Na|CF<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> and Li|CF<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> systems

Properties of CF _x /Li and CF _x /Na cells were examined while using galvanostatic charging/discharging, electrochemical impedance spectroscopy and scanning electron microscopy (SEM). The capacity during the first cycle was as high as ca. 1000 mAh g^?1. Such an electrode is suitable for primary CF _x /Li and CF _x /Na batteries. SEM images of CF _x cathode showed that during discharging it was transformed into amorphous carbon and LiF or NaF crystals (of diameter of ca. 5–20 μm). These systems (C?+?LiF or C?+?NaF) cannot be reversibly converted back into CF _x /Li or CF _x /Na, respectively. Exchange current densities are between 10^?7 Acm^?2 and 10^?9 Acm^?2 when working with LiPF₆ and NaPF₆ electrolytes (1.12?×?10^?7 Acm^?2 and 6.82?×?10^?9 Acm^?2, respectively). Those values are low and indicate that the charge transfer process may be the rate-determining step. Activation energies for the charge transfer process were 57 and 72 kJ mol^?1 for CF _x /LiPF₆ and CF _x /NaPF₆ systems, respectively. Higher activation energy barrier for the CF/Na⁺?+?e^??→?C?+?NaF reaction results in lower observed exchange current density in comparison to the system with lithium ions.     

Yields of Hydrogen and Hydrogen Peroxide from Argon–Water Vapor in Dielectric Barrier Discharge

Controlled chemical transformation of water vapor in dielectric barrier discharge (DBD) of argon into hydrogen and hydrogen peroxide for its usability as in situ or ex situ H₂ and H₂O₂ source are reported. Online analysis of the product gas mixture by conventional wet-chemical colorimetric method using buffered KI absorber solution revealed typical H₂O₂ G-value = 6.4 × 10^?3 µmol J^?1 (G-value defines as the number of molecules produced/consumed per 100 eV of energy; in SI unit G-value is expressed in µmol J^?1) in the absence of ozone. On the other hand, H₂ in product mixture analyzed in gas chromatograph-thermal conductivity detector (GC-TCD) with argon carrier revealed its G-value = 0.134 µmol J^?1. Enhancements in products’ yields were explored by varying gas residence time inside the plasma zone, and applied voltage and frequency on the dielectric surfaces. Employing a double-DBD reactor, at applied high voltage ~2.5 kV mm^?1 @50 Hz and gas residence time ~20 s resulted in the highest yields of H₂O₂. However, the H₂ yield increased continuously with increase in gas residence time. On the other hand, the single-dielectric barrier surface reactors were more efficient for high and exclusive generation of ex situ H₂ (e.g. maximum 1260 ppm; G-value typically 0.498 µmol J^?1).     

Highly efficient mesoporous WO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/KIT-6 catalysts for oxidative desulfurization of dibenzothiophene with hydrogen peroxide

Oxidative desulfurization (ODS) of organic compounds containing sulfur element from a model oil was performed using tungsten oxide catalysts supported on mesoporous silica with cubic Ia3d mesostructure, well-defined mesopores (7.2 nm), high surface area (719 m²/g), and three-dimensional pore network (WO _x /KIT-6). The prepared WO _x /KIT-6 catalysts (5–20 wt% WO _x ) were characterized by X-ray diffraction analysis, N₂ sorption measurements, electron microscopy, H₂-temperature programmed reduction, Raman spectroscopy, and thermogravimetric analysis. Among the mesoporous catalysts, 10 wt% WO _x /KIT-6 exhibited the best catalytic performance. Sulfur-containing organic compounds, such as dibenzothiophene, 4,6-dimethyldibenzothiophene, and benzothiophene, were completely (100 %) removed from the model oil over 10 wt% WO _x /KIT-6 catalyst in 2 h. In addition, the catalyst could be reused several times with only slight decrease in catalytic activity.     

Two New One-Dimensional Chain-Like Compounds Constructed from the Sandwich-Type Polyoxotungstate Clusters

Two new one-dimensional chain-like compounds, K₄Na₄[Mn₂(H₂O)₈Mn₄(H₂O)₂(GeW₉O₃₄)₂] · 20.5H₂O (1) and K₂Na₄Cu₂(H₂O)₁₂[Cu(H₂O)₂Cu₄(H₂O)₂(SiW₉O₃₄)₂] · 15H₂O (2), constructed from the sandwich-type clusters, have been obtained by the routine synthetic reactions in aqueous solutions, and their structures were determined by X-ray single crystal diffraction analysis. The crystal data is following: for 1, space group, monoclinic, P _21/n, a = 16.693(3) Å, b = 14.935(3) Å, c = 20.090(4) Å, β = 92.23(3)°, V = 5004.7(17) ų, Z = 2; For 2, space group, triclinic, P _?1, a = 11.744(2) Å, b = 13.415(3) Å, c = 17.609(4) Å, α = 73.08(3)°, β = 82.68(3)°, γ = 65.18(3)°, V = 2409.1(8) ų, Z = 1. The crystal structure of 1 shows a 1D ladder-like chain, built up of the sandwich anions [Mn₄(H₂O)₂(GeW₉O₃₄)₂]^12? and the Mn²⁺ ions. Compound 2 is a polymeric chain, composed of the Cu-substituted sandwich-type anions [Cu₄(H₂O)₂(SiW₉O₃₄)₂]^12? linked by the Cu(H₂O)₄ clusters. These extended materials based on the sandwich-type polyoxoanions are rarely reported in the POM chemistry.     

Enhanced lithium-ion intercalation and conduction of transparent tantalum oxide films by lithium addition with an atmospheric pressure plasma jet

An investigation is conducted on enhancing lithium-ion intercalation and conduction performance of transparent organo tantalum oxide (TaO _y C _z ) films, by addition of lithium via a fast co-synthesis onto 40 Ω/□ flexible polyethylene terephthalate/indium tin oxide substrates at the short exposed durations of 33–34 s, using an atmospheric pressure plasma jet (APPJ) at various mixed concentrations of tantalum ethoxide [Ta(OC₂H₅)₅] and lithium tert-butoxide [(CH₃)₃COLi] precursors. Transparent organo-lithiated tantalum oxide (Li _x TaO _y C _z ) films expose noteworthy Li⁺ ion intercalation and conduction performance for 200 cycles of reversible Li⁺ ion intercalation and deintercalation in a 1 M LiClO₄-propylene carbonate electrolyte, by switching measurements with a potential sweep from ?1.25 to 1.25 V at a scan rate of 50 mV/s and a potential step at ?1.25 and 1.25 V, even after being bent 360° around a 2.5-cm diameter rod for 1000 cycles. The Li⁺ ionic diffusion coefficient and conductivity of 6.2?×?10^?10 cm²/s and 6.0?×?10^?11 S/cm for TaO _y C _z films are greatly progressed of up to 9.6?×?10^?10 cm²/s and 7.8?×?10^?9 S/cm for Li _x TaO _y C _z films by co-synthesis with an APPJ.     

Effect of Ag addition on crystallization kinetics and thermal stability of As–Se chalcogenide glasses

Chalcogenide glasses of (As₅₀Se₅₀)_100?xAg_x (0 ≤ x ≤ 25) were prepared using the melt quenching technique under non-isothermal conditions. Differential scanning calorimetry curves measured at different heating rates (5 ≤ β ≤ 40 K min^?1) are used to characterize the as-quenched samples. The thermal stability was monitored through the calculation of the temperature difference T _c ? T _g, stability parameter S and crystallization rate factor K _p. The glass-forming ability (GFA) was investigated on the basis of Hurby parameter H _r which is a strong indicator of GFA. In addition, the activation energy of glass transition E _t, activation energy of crystallization E _c and Avrami exponent n of the studied compositions were determined. The mechanism of crystallization was found to be a combination of two- and three-dimensional crystal growth.     

Coordination Chemistry of the Magic Inorganic Building Block {Fe<Superscript>II</Superscript>[Mo<Subscript>6</Subscript>P<Subscript>4</Subscript>O<Subscript>31</Subscript>]<Subscript>2</Subscript>}: Hydrothermal Synthesis and Crystal Structure of a New Reduced Ferrous Molybdophosphate

A new reduced ferrous molybdophosphate composite solid of the formula, [(C₁₀H₁₄N₂)H]₄[Fe^II ₁₀Mo^V ₂₄(H₂PO₄)₄(HPO₄)₁₂(PO₄)₄(H₂O)₁₆(OH)₁₆O₄₄]·12H₂O, has been synthesized from a reaction mixture of MoO₃, FeSO₄·7H₂O, C₂H₂O₄·2H₂O, nicotine, H₃PO₄, and H₂O under hydrothermal conditions. The crystal data: monoclinic, space group C2/m, a = 24.4349(124), b = 12.9935(66), c = 14.7281(74) Å, β = 104.87(1) Å, V = 4520(4) Å³, Z = 2, R ₁  = 0.0874, wR ₂  = 0.2179. The structure is built from the building blocks of the formula, {Fe^II[Mo₆P₄O₃₁]₂}, consisting of a network of MO₆ (M = Fe, Mo) octahedral and PO₄ tetrahedral linked through their vertices. The connectivity of the building blocks with two pairs of face-sharing dinuclear Fe(II) clusters of the formula of [Fe^II ₂(H₂O)₄O₅] on which a phosphate group is hanging gives rise to one-dimensional chains with eight-membered apertures. The remarkable hydrogen bonded interactions between the chains form a unique and interesting framework with three-dimensional intersecting tunnels where the protonated nicotine molecules as structuring templates and crystallization water molecules are situated.     

Low Concentration Sulfolane-Based Electrolyte for High Voltage Lithium Metal Batteries

Electrolyte engineering is crucial for the commercialization of lithium metal batteries. Here, lithium metal is stabilized in the highly reactive sulfolane-based electrolyte under low concentration (0.25 M) for the first time. Inorganic-polymer hybrid solid electrolyte interphase (SEI) with high ionic conductivity, low bonding with lithium and high flexibility enables dense chunky lithium deposition and high plating/stripping efficiency. Low concentration electrolyte (LCE) also enables excellent cycling stability of LiNi_0.5Co_0.2Mn_0.3O₂ (NCM523)/Li cells at 1 C (90.7 % retention after 500 cycles) and 0.3 C (83.3 % retention after 1000 cycles). With a low N/P ratio (≈2), the capacity retention for NCM523/Li cells can achieve 94.3 % after 100 cycles at 0.3 C. Exploring the LCE is of paramount significance because it provides more possibilities of the lithium salt selections, especially reviving some lithium salts that are excluded before due to their low solubility. More importantly, LCE has the significant advantage of commercialization due to its cost-effectiveness.     

Synthesis and characterization of Sr<Subscript>0.75</Subscript>Y<Subscript>0.25</Subscript>Co<Subscript>0.9</Subscript>Ru<Subscript>0.1</Subscript>O<Subscript>3−<Emphasis Type="Italic">δ</Emphasis></Subscript> perovskite as a solid oxide fuel cell cathode material

The oxygen-deficient Sr_0.75Y_0.25Co_0.9Ru_0.1O_3?δ (SYCR) cathode is systematically evaluated for the application of solid oxide fuel cells. X-ray diffraction analysis indicates that SYCR presents a tetragonal structure with space group of I4/mmm (139). In the measured high oxygen partial pressure (pO₂) region (0.01–0.21 atm), the conductivity increases with increasing pO₂ because of the oxygen vacancy annihilation and hole creation, relating to a general p-type semiconducting mechanism. To get an insight into the rate-limiting step of SYCR cathode, behaviors of individual polarization resistance (R ₁ and R ₂) are investigated in different pO₂. The obtained fitting results reveal that R ₁ is nearly independent on the pO₂, while R ₂ presents a (pO₂)^?0.5 dependence. At 800 °C, SYCR cathode exhibits an R _p value of 0.14 Ω cm², moreover, when using the wet hydrogen (～ 3% H₂O) as fuel and ambient air as oxidant, the maximum power density of single cell Ni-YSZ (yttria-stabilized zirconia)|YSZ|SYCR reaches 452.9 W cm^?2.     

Synthesis,structural, and electrochemical properties of NaCo(PO<Subscript>3</Subscript>)<Subscript>3</Subscript> cathode for sodium-ion batteries

A new Co-base sodium metaphosphate compound, NaCo(PO₃)₃, has been synthesized here by solid-state method. The crystal structure is refined by the Rietveld method, and the results reveal that NaCo(PO₃)₃ has an orthorhombic structure with the space group of P2 ₁ 2 ₁ 2 ₁ and lattice parameters of a = 14.2453(2) Å, b = 14.2306(1) Å, and c = 14.2603(2) Å. Its typical morphology and chemical composition are confirmed by scanning electron microscopy (SEM) and energy-dispersive spectrometry (EDS). The valence states of all elements and the internal/external vibrational modes of NaCoP₃O₉ compound are measured by X-ray photoelectron and vibrational spectrum, where a typical feature of the (PO₃)^? polyanion group is observed. Meanwhile, the electrochemical properties of NaCo(PO₃)₃ cathode for sodium-ion batteries are also elevated and an initial discharge capacity of 33.8 mAh/g can be obtained at 0.05 C within 1.5–4.2 V. After 20 cycles, a discharge capacity of 26.7 mAh/g can be obtained and a well-kept oxidation–reduction plateau is still observed for NaCo(PO₃)₃ cathode, indicating the good reversibility of this metaphosphate electrode.     

Synthesis,crystal structure of new linear trinuclear isovalence Co(II)([Co<Subscript>3</Subscript>(H–L)<Subscript>2</Subscript>(L)<Subscript>2</Subscript>]), and visualizing intermolecular interactions with Hirshfeld surface method

S-allyl-β-N-[(2-hydroxyphenyl)methylene]hyrazinecarbodithioate) (1, H₂L), the Schiff base of dithiocarbazate with unsaturated allyl substitution, can act as a new tridentate SNO ligand H₂–L and react with cobalt(II) nitrate hexahydrate to form the novel linear trinuclear isovalence Co(II) complex, [Co₃(H–L)₂(L)₂] 2C₂H₅OH (2). The compounds were characterized by elemental analysis, infrared, and ultraviolet spectroscopy. Compound 2 was also characterized by single-crystal X-ray analysis and crystallizes in the orthorhombic space group, Pbcn, with a = 30.643(1) Å, b = 9.118(4) Å, c = 19.017(7) Å, α = β = γ = 90°, V = 5312.95 Å³, Z = 4, and R ₁ = 0.0790, (wR ₂) = 0.1223. The six-coordinate central Co(II) atom is bonded to two deprotonated metal-containing ligands. The terminal Co(II) atoms are in a square planar SNON four-coordinate environment and connected to the central Co(II) by N-atoms from the ligand backbone. For quantifying the intermolecular interactions in crystal lattice, the new d _norm surface and the breakdown of fingerprint plots have been used for visualizing and exploring the compound 2.     

New organic–inorganic hybrid structure based on paradodecatungstate clusters and imidazolium cations

An organic–inorganic hybrid material based on paradodecatungstate anions and imidazolium cations, Na₂(HIm)₈(H₂W₁₂O₄₂)·10H₂O (HIm: imidazolium), has been synthesized under mildly acidic conditions. This compound was characterized by single-crystal X-ray diffraction, IR and UV–visible spectroscopies, and thermogravimetric and differential thermal analyses. The compound crystallizes in the triclinic P-1 space group with a = 11.6945(8) Å, b = 12.4782(6) Å, c = 14.0952(9) Å, α = 106.041(3)°, β = 109.338(2)°, γ = 100.249(3)°, V = 1781.0(3) Å³, and Z = 2. The crystal structure exhibits an infinite 1D inorganic structure built from [H₂W₁₂O₄₂]^10? clusters and sodium cations; adjacent chains are further joined up by hydrogen-bonding interactions between protonated imidazole cations, water molecules, and polyoxoanions, to form a 3D supramolecular architecture.     

Comparative study of Co/TiO<Subscript>2</Subscript>, Co–Mn/TiO<Subscript>2</Subscript> and Co–Mn/Ti–Ce catalysts for oxidation of elemental mercury in flue gas

The Co–Mn/Ti–Ce catalyst prepared by sol–gel and impregnation method was evaluated for catalytic oxidation of Hg⁰ in the simulated flue gas compared with Co/TiO₂ and Co–Mn/TiO₂. The results showed that Co–Mn/Ti–Ce catalyst exhibited higher catalytic activity (around 93% Hg⁰ removal efficiency in the temperature of 150 °C with 6% O₂, 400 ppm NO, 200 ppm SO₂ and 3% H₂O) than Co/TiO₂ and Co–Mn/TiO₂. Based on the characterization results of N₂ adsorption–desorption, XRD, UV–Vis, XPS, H₂-TPR and Hg-TPD, it could be concluded that the lower band gap, better reducibility and mercury adsorption capability and the presence of Co³⁺/Co²⁺, Mn⁴⁺/Mn³⁺ and Ce⁴⁺/Ce³⁺ redox couples as well as surface oxygen species contributed to the excellent Hg⁰ oxidation removal performance. In addition, well dispersion of active components and a synergetic effect among Co, Mn and Ce species might improve the activity further. A Mars–Maessen mechanism is thought to be involved in the Hg⁰ oxidation. The lattice oxygen derived from MnO _x or CoO _x would react with adsorbed Hg⁰ to form HgO and the consumption of lattice oxygen could be replenished by O₂. For Co–Mn/Ti–Ce, MnO _x?1 could be alternatively reoxidized by the lattice oxygen derived from adjacent CoO _x and CeO _x which is beneficial to the Hg⁰ oxidation.     

Synthesis and characterization of high-dimensional structure based on paradodecatungstate clusters and sodium–aminoacetic acid complex subunits

An organic–inorganic hybrid material based on paradodecatungstate building blocks and sodium–aminoacetic acid complex subunits,{Na₁₀(H₃N–CH₂–COO)₂[H₂W₁₂O₄₂]}·28H₂O (1), have been synthesized under mildly acidic conditions. This compound was characterized by single-crystal X-ray diffraction, elemental analysis, IR and UV–visible spectroscopies, and cyclic voltammetry. The compound crystallizes in the triclinic space group P-1 with a = 11.879(2) Å, b = 12.706(2) Å, c = 13.067(2) Å, α = 74.11(3)°, β = 79.71(3)°, γ = 65.95(3)°, V = 1727.2(5) Å³, and Z = 1. The crystal structure consists of infinite 2D layers constructed from [H₂W₁₂O₄₂]^10? clusters and sodium–aminoacetic acid complexes; adjacent layers are further joined by the complex units and sodium cations to yield a three-dimensional network.     

Chemical Composition,Physical Properties and Populating Mechanism of Some O(I) States for a DC Discharge in Oxygen with Water Cathode

This paper reports the results of the experimental study of parameters for a DC oxygen discharge with water cathode in the pressure range of 0.1–1 bar and the discharge current of 40 mA. The radius of positive column, the cathode voltage drop, the cathode current density and the electric field strength were measured. Rotational temperatures of N₂ (C³Π_u, V = 0) and OH (A²Σ, V = 0) and absolute line intensities of atomic oxygen with wave length of 845 and 777 nm were determined as well. Plasma composition modeling was carried out by the combined solution of the Boltzmann equation for electrons, the equations of vibrational kinetics for ground states of N₂, O₂, H₂O molecules, and the equations of chemical kinetics, and the plasma conductivity equation. Calculations were carried out taking into consideration the discharge radial heterogeneity and using experimental values of E/N and gas temperatures. The main particles being formed in plasma were shown to be ^·OH, H₂O₂, O(³P), O₂(a¹Δ_g), O₂(b¹Σ _g ⁺ ), H(¹S). On the basis of this calculation and experimental values of line intensities, the populating mechanism of (3p ³P) level of atomic oxygen was discussed. The comparison of some properties of discharges in O₂, N₂ and air was done.     

Synthesis,crystal structure of a new tetranuclear Ni<Stack><Subscript>2</Subscript><Superscript>II</Superscript></Stack>Cu<Stack><Subscript>2</Subscript><Superscript>II</Superscript></Stack> complex containing a macrocyclic ligand

The first inorg/organic hybrid complex incorporating the macrocyclic oxamide, of formula [(NiL)₂Cu₂(μ-NSC)₂(NSC)₂] (1), (NiL, H₂L = 2, 3-dioxo-5,6,14,15-dibenzo-1,4,8,12-tetraazacyclo-pentadeca-7,13-dien), have been synthesized and structurally characterized. The crystals crystallize in the triclinic system, space group P-1, for (1) a = 8.319(3) Å, b = 10.434(4) Å, c = 14.166(5) Å, a = 107.030(5)°, β  =  91.257(5)°, γ = 107.623(5)°. The complex involved both bridging N, S-ligand, and oxamide ligand, C–H?S interactions and NCS → Ni weak coordination interactions making the complex superamolecular.     

Self-Assembly,Crystal Structure and Analysis of Intermolecular Interactions of the Supramolecular Compound Based on Hexamolybdochromate(III), Sulfate and Piperazine

A new supramolecular compound based on Anderson-B hexamolybdochromate, (H₂Pz)₃[Cr(OH)₆Mo₆O₁₈H](SO₄)₂·12H₂O (1) (Pz = piperazine) was synthesized and characterized by elemental analysis, IR spectroscopy, and single-crystal X-ray diffraction (Mo Kα). The compound crystallizes in monoclinic system, P21/c space group with a = 13.5708(6) Å, b = 17.3711(8) Å, c = 22.2387(9) Å, β = 110.631(2)°; V = 4906.3(4) Å³, Z = 4, D _c  = 2.290 g/cm³, F(000) = 3364.0; μ = 1.905, S = 1.033. The final R = 0.0398 and wR = 0.0971. The H₂pz²⁺ ions and sulfate anions in 1 are arranged through hydrogen bonds into a hexagonal network in [202] plane and hexamolybdochromates anions (CrMo₆) fill in the hexagonal vacancies. The networks stack in such a way that each anion links two sulfate ions from adjacent networks via hydrogen bonds with short (CrMo₆)O···OSO₃ distances of 2.637–2.697 Å. A lot of hydrogen bonds are formed between water molecules, sulfate, H₂pz²⁺ ions and CrMo₆ anions, which are the dominating force constructing the supramolecular structure. Hirshfeld surface analysis of 1 gives us the details of intermolecular interactions in the crystals of 1 in a visual manner and shows that the CrMo₆ anion acts as a stronger hydrogen bond donor than as an acceptor.     

Gas-phase conversion of the U(VI), Sr,Mo, and Zr compounds in nitrating atmosphere

The gas-phase conversion of U₃O₈, MoO₃, SrO, and their mechanical mixtures, and also of ZrO₂ into water-soluble compounds in the atmosphere of (NO _x  + vapor H₂O) or HNO₃ (vapor) was studied. In the course of gas-phase conversion, U₃O₈ and SrO transform into water-soluble compounds (nitrates, hydroxonitrates), whereas MoO₃ and ZrO₂ undergo no changes. The principal possibility of separating U from Mo and Zr by gas-phase conversion of the oxides in the atmosphere of (NO _x  + vapor H₂O) or HNO₃ (vapor) was demonstrated.     

Synthesis and characterization of a new monophosphate (C<Subscript>6</Subscript>H<Subscript>16</Subscript>N<Subscript>2</Subscript>)(H<Subscript>2</Subscript>PO<Subscript>4</Subscript>)<Subscript>2</Subscript>

Chemical preparation, crystal structure, and NMR spectroscopy of a new trans-2,5-dimethylpiperazinium monophosphate are given. This new compound crystallizes in the triclinic system, with the space group P-1 and the following parameters: a = 6.5033(3), b = 7.6942(4), c = 8.1473(5) Å, α = 114.997(3), β = 92.341(3), γ = 113.136(3), V = 329.14(3) ų, Z = 1, and D_x = 1.565 g cm^?3. The crystal structure has been determined and refined to R = 0.030 and R _w(F ²) = 0.032 using 1558 independent reflections. The structure can be described as infinite [H₂PO₄] _n ^n? chains with (C₆H₁₆N₂)²⁺ organic cations anchored between adjacent polyanions to form columns of anions and cations running along the b axis. This compound has also been investigated by IR, thermal, and solid-state, ¹³C and ³¹P MAS NMR spectroscopies and Ab initio calculations.