Cobalt-doped BiVO<Subscript>4</Subscript> (Co-BiVO<Subscript>4</Subscript>) as a visible-light-driven photocatalyst for the degradation of malachite green and inactivation of harmful microorganisms in wastewater

Co-doped BiVO₄, a visible-light-responsive photocatalytic semiconductor, was synthesized using a microwave hydrothermal method. The doped sample exhibited much higher photocatalytic activity for malachite green degradation under visible light irradiation than undoped BiVO₄. Similarly, improved inactivation efficiency toward Escherichia coli and Chlamydomonas pulsatilla (green tide) were observed with Co-doped BiVO₄. The degradation of malachite green by Co-doped BiVO₄ reaches 99% within 90 min irradiation to visible light. Similarly, the inactivation of Escherichia coli reaches 81.3% in 5 h and Chlamydomonas pulsatilla reaches 65.6% in 1 h irradiation to visible light. The enhanced photoactivity is believed to be due to the increment of the visible light absorption range by narrowing the band gap energy. In addition, the highly exposed reactive (010) facets can efficiently capture the photoinduced electrons, promote charge separation, and reduce recombination probability. Thus, these findings provide mechanistic insight into the effectiveness of Co-doped BiVO₄ semiconductors for the treatment of wastewater that contains industrial effluents and microorganisms.     

Fabrication and characterisation of a mixed oxide-covered mesh electrode composed of NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript> and its capability of generating hydroxyl radicals during the oxygen evolution reaction in electrolyte-free water

A mixed oxide-covered mesh electrode composed of NiCo₂O₄ (MOME-NiCo₂O₄) was prepared on a stainless-steel substrate using thermal decomposition (slow-cooling rate method). Surface, bulk and electrochemical properties of MOME were studied using different techniques, namely scanning electron microscopy (SEM), X-ray diffraction (XRD), cyclic voltammetry (CV) with determination of the electrochemical porosity (?) and morphology factor (φ) parameters, quasi-stationary polarisation curves (PC) and electrochemical impedance spectroscopy (EIS). SEM images revealed a good coverage of the metallic wires by a compact oxide layer (absence of cracks). XRD analysis confirmed the formation of the spinel NiCo₂O₄ with the presence of NiO. The ‘in situ’ surface parameters denoted as ? and φ exhibited values of 0.39 and 0.33, respectively, revealing that the electrochemically active surface area is mainly confined to the ‘outer/external’ surface regions of the oxide layer. The PC was characterised by two Tafel slopes distributed in the low (b ₁ = 46 mV dec^?1) and high (b ₂ = 59 mV dec^?1) overpotential domains. The corresponding apparent exchange current densities were j ₀₍₁₎ = (3.43 ± 0.11) × 10^?6 A cm^?2 and j ₀₍₂₎ = (6.70 ± 0.08) × 10^?6 A cm^?2, respectively. The EIS study accomplished in the low-overpotential domain revealed a Tafel slope (b ₁) of 51 mV dec^?1. According to the spin-trapping reaction using N,N-dimethyl-p-nitrosoaniline (RNO), the MOME-NiCo₂O₄ electrode exhibited good performance for the generation of weakly adsorbed hydroxyl radicals (HO^?) during the OER in electrolyte-free water.     

Synthesis and characterization of a new monophosphate (C<Subscript>6</Subscript>H<Subscript>16</Subscript>N<Subscript>2</Subscript>)(H<Subscript>2</Subscript>PO<Subscript>4</Subscript>)<Subscript>2</Subscript>

Chemical preparation, crystal structure, and NMR spectroscopy of a new trans-2,5-dimethylpiperazinium monophosphate are given. This new compound crystallizes in the triclinic system, with the space group P-1 and the following parameters: a = 6.5033(3), b = 7.6942(4), c = 8.1473(5) Å, α = 114.997(3), β = 92.341(3), γ = 113.136(3), V = 329.14(3) ų, Z = 1, and D_x = 1.565 g cm^?3. The crystal structure has been determined and refined to R = 0.030 and R _w(F ²) = 0.032 using 1558 independent reflections. The structure can be described as infinite [H₂PO₄] _n ^n? chains with (C₆H₁₆N₂)²⁺ organic cations anchored between adjacent polyanions to form columns of anions and cations running along the b axis. This compound has also been investigated by IR, thermal, and solid-state, ¹³C and ³¹P MAS NMR spectroscopies and Ab initio calculations.     

Kinetics of Li-ion transfer reaction at LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>, LiCoO<Subscript>2</Subscript>, and LiFePO<Subscript>4</Subscript> cathodes

Kinetics of LiFePO₄, LiMn₂O₄, and LiCoO₂ cathodes operating in 1 M LIPF₆ solution in a mixture of ethylene carbonate and dimethyl carbonate was deduced from impedance spectra taken at different temperatures. The most striking difference of electrochemical impedance spectroscopy (EIS) curves is the impedance magnitude: tens of ohms in the case of LiFePO₄, hundreds of ohms for LiMn₂O₄, and thousands of ohms for LiCoO₂. Charge transfer resistances (R _ct) for lithiation/delitiation processes estimated from the deconvolution procedure were 6.0 Ω (LiFePO₄), 55.4 Ω (LiCoO₂), and 88.5 Ω (LiMn₂O₄), respectively. Exchange current density for all the three tested cathodes was found to be comparable (0.55–1·10^?2 mAcm^?2, T = 298 K). Corresponding activation energies for the charge transfer process, \( {E}_{ct}^{\#} \), differed considerably: 66.3, 48.9, and 17.0 kJmol^?1 for LiMn₂O₄, LiCoO₂, and LiFePO₄, respectively. Consequently, temperature variation may have a substantial influence on exchange current densities (j _o) in the case of LiMn₂O₄ and LiCoO₂ cathodes.     

Study of variation in thermophysical properties of RE<Subscript>6</Subscript>UO<Subscript>12</Subscript>(s) along the lanthanide series

The novel ligand N,N,N′′′′,N′′′′-tetrabutyl-N′′′,N′′′-(N″,N″-diethyl)-ethidene bisdiglycolamide (TBEE-BisDGA) and other eight analogous extractants have been synthesized and characterized by NMR and HRMS. The solvent extraction of Th⁴⁺, UO₂ ²⁺ and Eu³⁺ from nitric acid solution using the above BisDGA extractants was investigated in 1-dodecanol at 30 ± 1 °C. The extractants exhibited higher affinity toward Th⁴⁺ than UO₂ ²⁺ and Eu³⁺ in the present system. The maximum value of separation factor SF _Th(IV)/U(VI) and SF _{Th(IV)/Eu(III)} is 78.5 and 53.3 respectively for TBEE-BisDGA, 88.1 and 69.5 respectively in the case of TB ^i-PE-BisDGA at 3 M HNO₃ solution.     

Coordination Chemistry of the Magic Inorganic Building Block {Fe<Superscript>II</Superscript>[Mo<Subscript>6</Subscript>P<Subscript>4</Subscript>O<Subscript>31</Subscript>]<Subscript>2</Subscript>}: Hydrothermal Synthesis and Crystal Structure of a New Reduced Ferrous Molybdophosphate

A new reduced ferrous molybdophosphate composite solid of the formula, [(C₁₀H₁₄N₂)H]₄[Fe^II ₁₀Mo^V ₂₄(H₂PO₄)₄(HPO₄)₁₂(PO₄)₄(H₂O)₁₆(OH)₁₆O₄₄]·12H₂O, has been synthesized from a reaction mixture of MoO₃, FeSO₄·7H₂O, C₂H₂O₄·2H₂O, nicotine, H₃PO₄, and H₂O under hydrothermal conditions. The crystal data: monoclinic, space group C2/m, a = 24.4349(124), b = 12.9935(66), c = 14.7281(74) Å, β = 104.87(1) Å, V = 4520(4) Å³, Z = 2, R ₁  = 0.0874, wR ₂  = 0.2179. The structure is built from the building blocks of the formula, {Fe^II[Mo₆P₄O₃₁]₂}, consisting of a network of MO₆ (M = Fe, Mo) octahedral and PO₄ tetrahedral linked through their vertices. The connectivity of the building blocks with two pairs of face-sharing dinuclear Fe(II) clusters of the formula of [Fe^II ₂(H₂O)₄O₅] on which a phosphate group is hanging gives rise to one-dimensional chains with eight-membered apertures. The remarkable hydrogen bonded interactions between the chains form a unique and interesting framework with three-dimensional intersecting tunnels where the protonated nicotine molecules as structuring templates and crystallization water molecules are situated.     

<Emphasis Type="Italic">cis</Emphasis>-Dioxomolybdenum(VI) complexes of sterically encumbered phenol-based tetradentate N<Subscript>2</Subscript>O<Subscript>2</Subscript> ligands: Structural,spectroscopic, and electrochemical studies

Two cis-dioxomolybdenum(VI) complexes [MoO₂L] (L: L ¹, 2 and L: L ², 3) in a phenol-based sterically encumbered N₂O₂ ligand environment have been synthesized, and their crystallographic characterizations are reported. The orange crystals of 2 are monoclinic, space group P2₁/a with unit cell dimensions as a=16.2407(17) Å, b=7.2857(8) Å, c=18.400(2) Å, β=98.002(9)°, Z=4, and d _cal=1.486 g cm^?3. The light orange crystals of 3, however, are orthorhombic, space group, Pbcn, with unit cell dimensions a=8.3110(12) Å, b=12.637(3) Å, c=34.673(5) Å, Z=4, and d _cal=1.187 g cm^?3. The structures were refined by a full-matrix least-squares procedure on F ² to a final R=0.046 (0.055 for 3) using 4944 (3677) all independent data. In both the cases, the Mo atom exists in a distorted octahedral geometry defined by a N₂O₄ donor set, which features a cis-Mo(–O)₂ and a trans-Mo(OPh)₂ arrangement. Compound 2 undergoes a quasireversible one-electron reduction at ?1.3 V vs Ag/AgCl reference due to Mo^VIO₂/Mo^VO₂ electron transfer and thus providing a rare example of steric solution to the comproportionation–dimerization problem encountered frequently in the development of valid biomimetic models for the active sites of oxomolybdenum enzymes.     

Electrochemical sensor using graphene/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> nanosheets functionalized with garlic extract for the detection of lead ion

Based on the modulated electronic properties of Fe₃O₄-graphene (Fe₃O₄/GN composite) as well as the outstanding complexation between Pb²⁺ and natural substances garlic extract (GE), a novel electrochemical sensor for the determination of Pb²⁺ in wastewater was prepared by immobilization of Fe₃O₄/GN composite integrated with GE onto the surface of glassy carbon electrode (GCE). Fe₃O₄/GN composite was employed as an electrochemical active probe for enhancing electrical response by facilitating charge transfer while GE was used to improve the selectivity and sensitivity of the proposed sensor to Pb²⁺ assay. The electrochemical sensing performance toward Pb²⁺ was appraised by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and square wave voltammetry (SWV). Under the optimized condition, the sensor exhibited two dynamic linear ranges (LDR) including 0.001 to 0.5 nM and 0.5 to 1000 nM with excellent low detection limit (LOD) of 0.0123 pM (S/N =?3) and quantification limit (LOQ) of 0.41 pM (S/N =?10). Meanwhile, it displayed remarkable stability, reproducibility (RSD of 3.61%, n =?3), and selectivity toward the assay for the 100-fold higher concentration of other heavy metal ions. Furthermore, the novel sensor has been successfully employed to detect Pb²⁺ from real water samples with satisfactory results.     

Red water treatment by photodegradation process in presence of modified TiO<Subscript>2</Subscript> nanoparticles and validation of treatment efficiency by MLR technique

An active photocatalyst under sunlight irradiation was proposed for treatment of red water of TNT production process. The nanoparticles of TiO₂/S_0.05,Zn_0.05 were prepared by the sol–gel method and were verified by XRD pattern, TEM image, EDXS analysis, BET analysis and DRS spectra. The proposed photocatalyst showed the surface area of 146 m² g^?1, anatase and rutile phases and band-gap energy of 2.92 eV. The prepared nanoparticles were used as photocatalyst in treatment of red water under UV lamp and sun irradiations. The photodegradation process was optimized in conditions of 5 g L^?1 of photocatalyst, irradiation time of 4 h and dilution times of 1000 of real samples. The treatment efficiency of 76 and 69 % and rate constants of 0.368 and 0.319 h^?1 were obtained under UV and sun irradiations, respectively. The multiple linear regression as a statistic technique was used for study of validation and verification of four factors of mole fraction of S dopant, the irradiation intensity of UV lamp, the dose of photocatalyst and dilution times on samples as predictor’s on the treatment efficiency of red water as the response variable. The output of MLR showed the obtained P values <0.05 in confidence level of 95 % for all of the variables. Thus, the null hypothesis is rejected, and a meaningful addition is observed in the model because changes in the predictor’s value are related to changes in the response variable.     

Synthesis,structural, and electrochemical properties of NaCo(PO<Subscript>3</Subscript>)<Subscript>3</Subscript> cathode for sodium-ion batteries

A new Co-base sodium metaphosphate compound, NaCo(PO₃)₃, has been synthesized here by solid-state method. The crystal structure is refined by the Rietveld method, and the results reveal that NaCo(PO₃)₃ has an orthorhombic structure with the space group of P2 ₁ 2 ₁ 2 ₁ and lattice parameters of a = 14.2453(2) Å, b = 14.2306(1) Å, and c = 14.2603(2) Å. Its typical morphology and chemical composition are confirmed by scanning electron microscopy (SEM) and energy-dispersive spectrometry (EDS). The valence states of all elements and the internal/external vibrational modes of NaCoP₃O₉ compound are measured by X-ray photoelectron and vibrational spectrum, where a typical feature of the (PO₃)^? polyanion group is observed. Meanwhile, the electrochemical properties of NaCo(PO₃)₃ cathode for sodium-ion batteries are also elevated and an initial discharge capacity of 33.8 mAh/g can be obtained at 0.05 C within 1.5–4.2 V. After 20 cycles, a discharge capacity of 26.7 mAh/g can be obtained and a well-kept oxidation–reduction plateau is still observed for NaCo(PO₃)₃ cathode, indicating the good reversibility of this metaphosphate electrode.     

Thermal properties,phase transitions,vibrational and reorientational dynamics of [Mn(NH<Subscript>3</Subscript>)<Subscript>6</Subscript>](NO<Subscript>3</Subscript>)<Subscript>2</Subscript>

[Mn(NH₃)₆](NO₃)₂ crystallizes in the cubic, fluorite (C1) type crystal lattice structure (Fm \( \overline{3} \) m) with a = 11.0056 Å and Z = 4. Two phase transitions of the first-order type were detected. The first registered on DSC curves as a large anomaly at T _C1 ^h  = 207.8 K and T _C1 ^c  = 207.2 K, and the second registered as a smaller anomaly at T _C2 ^h  = 184.4 K and T _C2 ^c  = 160.8 K (where the upper indexes h and c denote heating and cooling of the sample, respectively). The temperature dependence of the full width at half maximum of the band associated with the δ_s(HNH)F_1u mode suggests that the NH₃ ligands in the high temperature and intermediate phase reorientate quickly with correlation times in the order of several picoseconds and with activation energy of 9.9 kJ mol^?1. In the phase transition at T _C2 ^c probably only a some of the NH₃ ligands stop their reorientation, while the remainders continue to reorientate quickly with activation energy of 7.7 kJ mol^?1. Thermal decomposition of the investigated compound starts at 305 K and continues up to 525 K in four main stages (I–IV). In stage I, ²/₆ of all NH₃ ligands were seceded. Stages II and III are connected with an abruption of the next ²/₆ and ¹/₆ of total NH₃, respectively, and [Mn(NH₃)](NO₃)₂ is formed. The last molecule of NH₃ per formula unit is freed at stage IV together with the simultaneous thermal decomposition of the resulting Mn(NO₃)₂ leading to the formation of gaseous products (O₂, H₂O, N₂ and nitrogen oxides) and solid MnO₂.     

Hydrogen bonding and structural complexity in the Cu<Subscript>5</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>(OH)<Subscript>4</Subscript> polymorphs (pseudomalachite,ludjibaite, reichenbachite): combined experimental and theoretical study

Hydrogen bonding in the Cu₅(PO₄)₂(OH)₄ polymorphs pseudomalachite, ludjibaite and reichenbachite has been studied by low-temperature single-crystal X-ray diffraction (XRD; pseudomalachite) and solid-state density functional theory (DFT; pseudomalachite, ludjibaite, reichenbachite) calculations. Pseudomalachite at 100 K is monoclinic, P2₁/c, a = 4.4436(4), b = 5.7320(5), c = 16.9300(15) Å, β = 91.008(8)°, V = 431.15(7) ų and Z = 2. The structure has been refined to R ₁ = 0.025 for 1383 unique observed reflections with |F _o| ≥ 4σ_F. DFT calculations were done with the CRYSTAL14 software package. For pseudomalachite, the difference between the calculated and experimental H sites does not exceed 0.152 Å. Structural configurations around hydroxyl groups in all three polymorphs show many similarities. Each OH5 group is involved in a three-center (bifurcated) hydrogen bond with the H···A distances in the range of 2.141–2.460 Å and the D–H···A angles in the range of 122.41°–139.30°, whereas each OH6 group forms a four-center (trifurcated) bond (H···A = 2.093–2.593 Å; D–H···A = 122.79°–137.71°). The crystal structures of the Cu₅(PO₄)₂(OH)₄ polymorphs are based on three-dimensional frameworks of Cu and P polyhedra. The copper-centered octahedra share edges to form two-dimensional layers parallel to (100) in all three structures. The layers have square voids above and beneath PO₄ tetrahedra that link adjacent layers by sharing O atoms with two CuO₆ octahedra each. From the topological point of view, none of the polymorphs can be obtained from another by a displacive transformation, and therefore pseudomalachite, ludjibaite and reichenbachite can be viewed as combinatorial polymorphs. According to information-based structural complexity considerations, the three phases are very similar in their configurational entropies and preferential crystallization of one phase over another cannot be entropy driven and is probably governed by other mechanisms that may involve such factors as structures of prenucleation clusters, chemical admixtures, etc.     

Physical and photoelectrochemical characterizations of SrWO<Subscript>4</Subscript> prepared by thermal decomposition. Application to the photo electro-oxidation of ibuprofen

We have reported the semi conducting and photoelectrochemical properties of SrWO₄ prepared by chemical route. The phase purity is confirmed by X-ray diffraction and the oxide is characterized by scanning electron microscopy, diffuse reflectance, and electrochemical impedance spectroscopy. SrWO₄ crystallizes in the scheelite structure with an average crystallite size of 378 ± 6 nm. The Raman spectrum gives an intense peak at 920 cm^?1 assigned to A _g mode while the infrared analysis confirms the hexagonal coordination of tungsten. The UV-visible spectroscopy shows an indirect optical transition at 2.60 eV. SrWO₄ exhibits n-type conduction by oxygen deficiency, confirmed by the chrono-amperometry and the intensity potential J(E) curve shows a small hysteresis. The Mott-Schottky plot gives electrons density of 5.72 × 10¹⁸ cm^?3 and a flat band potential of 0.27 V_SCE, indicating that the conduction band derives mainly from W⁶⁺: 6s orbital. The electrochemical impedance spectroscopy (EIS), measured in the range (1–10⁵ Hz), shows the predominance of the bulk contribution with a dark impedance of 38 kΩ cm². As application, the ibuprofen is degraded by electrocatalysis on SrWO₄ with a conversion rate of 42%. An improvement up to 77% has been obtained by electrophotocatalysis under UV light; the conversion follows a first order kinetic with a rate constant of 2.32 × 10^?4 min^?1.     

Structural investigation of [Au(en)<Subscript>2</Subscript>]Cl(ReO<Subscript>4</Subscript>)<Subscript>2</Subscript> and [Au(en)<Subscript>2</Subscript>](ReO<Subscript>4</Subscript>)<Subscript>3</Subscript> complexes

Novel complex salts [Au(en)₂]Cl(ReO₄)₂ (I) and [Au(en)₂](ReO₄)₃ (II), en = ethylenediamine, are obtained. Their crystal structures are determined by single crystal X-ray diffraction. Complex I crystallizes in the triclinic crystal system: a = 6.2172(7) Å, b = 7.1644(8) Å, c = 8.8829(8) Å, α = 96.605(4)°, β = 110.000(4)°, γ = 97.802(4)°, P-1 space group, Z = 1, d _x = 3.905 g/cm³; complex II crystallizes in the monoclinic crystal system: a = 15.244(2) Å, b = 7.6809(8) Å, c = 9.3476(12) Å, β = 127.004(3)°, C2 space group, Z = 4, d _x = 4.057 g/cm³.     

Synthesis and magnetic properties of quasi-unidimensional oxide Sr<Subscript>6.3</Subscript>Rh<Subscript>2.35</Subscript>Mn<Subscript>2.35</Subscript>O<Subscript>15</Subscript>

Attempts of the synthesis in air of complex oxides Sr₃RhMnO_x and Sr₄Rh_1.5Mn_1.5O_x resulted in revealing formation of a new oxide phase Sr_6.3Rh_2.35Mn_2.35O₉ related to quasi-unidimensional family A_3n+3m A′ _n B_3m+n O_9m+6n at n = 1 and m = 1. Its structural characteristics and magnetic properties are studied. X-ray data of the obtained phase is indicated on the basis of trigonal cell (spatial group P321) with the parameters: a 9.6239(4) Å; c ₁ 4.1130(4) Å, c ₂ 2.4946(2) Å. Manganese and rhodium exist in the compound as the cations Mn⁴⁺, Rh³⁺ and Rh⁴⁺, as follows from the data of measuring of magnetic susceptibility in the range 2–300 K.     

Crystal structure of KPb<Subscript>2</Subscript>Cl<Subscript>5</Subscript> and KPb<Subscript>2</Subscript>Br<Subscript>5</Subscript>

The KPb₂Cl₅ and KPb₂Br₅ crystals are monoclinic (P2₁/c) with a microtwinned structure. X-ray analysis of chloride resulted in the parameters a = 8.854(2) Å, b = 7.927(2) Å, c = 12.485(3) Å; β = 90.05(3)°, d_calc = 4.78(1) g/cm³ (STOE STADI4, MoK_α, 2θ_max = 80°), R₁ = 0.0702 for 4094 F ≥ 4 σ(F) reflections. For bromide, a = 9.256(2) Å, b = 8.365(2) Å, c = 13.025(3) Å; β = 90.00(3)°, d_calc = 5.62(1) g/cm³ (Bruker P4, MoK_α, 2θ_max = 70°), R₁ = 0.0692 for 3076 F ≥ 4 (F) reflections.     

Crystal structure of osmium selenobromide OsSe<Subscript>2</Subscript>Br<Subscript>12</Subscript>

The crystal structure of the compound OsSe₂Br₁₂ obtained by the reaction of OsBr₄ with SeBr₄ or Se in liquid bromine at 100°C was studied by X-ray powder diffraction. The structure of osmium selenobromide corresponds to a specific type: space group C2/m, a = 14.0464(2) Å, b = 11.05398(14) Å, c = 6.50340(9) Å, β = 112.2645(11)°, Z = 2; R _B = 0.03946, R _wp = 0.05403, χ² = 4.261 for 479 reflections and 53 refinement parameters. The X-ray diffraction analysis confirmed the earlier assumption concerning the cation-anion structure of the compound representing a packing of nearly regular [OsBr₆]^2? octahedra as anionic complexes and deficient [:SeBr₃]⁺ tetrahedra as cationic complexes in which the missing vertex is occupied by the lone electron pair of selenium.     

Synthesis and X-ray investigation of Rb<Subscript>2</Subscript>[Pd(NO<Subscript>3</Subscript>)<Subscript>4</Subscript>] and Cs<Subscript>2</Subscript>[Pd(NO<Subscript>3</Subscript>)<Subscript>4</Subscript>]

Powder and single crystal X-ray diffraction studies have been performed for anhydrous nitrate complexes Rb₂[Pd(NO₃)₄] (I) and Cs₂[Pd(NO₃)₄] (II). Crystal data for I: a = 7.843(1) Å, b = 7.970(1) Å, c = 9.725(1) Å; β = 100.39(1)°, V = 597.9(1) Å ³, space group P2₁/c, Z = 2, d _calc = 2.918 g/cm³; for II: a = 10.309(2) Å, b = 10.426(2) Å, c = 11.839(2) Å; β = 108.17(3)°, V = 1209.0(4) ų, space group P2₁/c, Z = 4, d ^calc = 3.408 g/cm³. The structures are formed by isolated [Pd(NO₃)₄]^2? complex anions and alkali metal cations. The plane-square environment of the Pd atom is formed from the oxygen atoms of the monodentate nitrate groups. The geometrical characteristics of the complex anions are analyzed. Compound II has a short contact Pd...Cs 3.252 Å.     

Crystal structures of <Emphasis Type="Italic">trans</Emphasis>-[Re<Subscript>6</Subscript>S<Subscript>8</Subscript>(CN)<Subscript>2</Subscript>L<Subscript>4</Subscript>] complexes,L = pyridine or 4-methylpyridine

The structures of three novel octahedral rhenium cluster compounds [Re₆S₈(CN)₂(py)₄]·H₂O (1), [Re₆S₈(CN)₂(4-Mepy)₄] (2), [Re₆S₈(CN)₂(4-Mepy)₄]·4-Mepy (3) (py = pyridine, 4-Mepy = 4-methylpyridine) are determined by X-ray crystallography. Crystal data are: C2/m space group, a = 14.813(1) Å, b = 14.772(1) Å, c = 9.2122(6) Å, β = 119.085(2)°, V = 1761.7(2) ų, d _x = 3.318 g/cm³, R = 0.0585 (1); I4₁/amd space group, a = 16.0018(3) Å, c = 14.7186(5) Å, V = 3768.81(16) ų, d _x = 3.169 g/cm³, R = 0.0489 (2); P2₁/c space group, a = 9.0452(4) Å, b = 15.8065(7) Å, c = 15.2951(6) Å, β = 103.700(2)°, V = 2124.57(16) ų, d _x = 2.957 g/cm³, R = 0.0245 (3). Molecular cluster complexes interact via π-π stacking affording 3D frameworks in 1 and 2 and chains in 3.     

Sn-doped Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode materials for lithium-ion batteries with enhanced electrochemical performance

Sn-doped Li-rich layered oxides of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ have been synthesized via a sol-gel method, and their microstructure and electrochemical performance have been studied. The addition of Sn⁴⁺ ions has no distinct influence on the crystal structure of the materials. After doped with an appropriate amount of Sn⁴⁺, the electrochemical performance of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ cathode materials is significantly enhanced. The optimal electrochemical performance is obtained at x = 0.01. The Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode delivers a high initial discharge capacity of 268.9 mAh g^?1 with an initial coulombic efficiency of 76.5% and a reversible capacity of 199.8 mAh g^?1 at 0.1 C with capacity retention of 75.2% after 100 cycles. In addition, the Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode exhibits the superior rate capability with discharge capacities of 239.8, 198.6, 164.4, 133.4, and 88.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively, which are much higher than those of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ (196.2, 153.5, 117.5, 92.7, and 43.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively). The substitution of Sn⁴⁺ for Mn⁴⁺ enlarges the Li⁺ diffusion channels due to its larger ionic radius compared to Mn⁴⁺ and enhances the structural stability of Li-rich oxides, leading to the improved electrochemical performance in the Sn-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ cathode materials.