Synthesis and photoluminescence of titania nanoparticle arrays templated by block-copolymer thin films.

High-density arrays of titania nanoparticles were prepared using a polystyrene-b-poly(ethylene oxide) block copolymer (PS-b-PEO) as a template and a titanium tetraisopropoxide based sol-gel precursor as titania source via a spin-coating method. The hydrophilic titania sol-gel precursor was selectively incorporated into hydrophilic PEO domains of PS-b-PEO and form titania nanoparticle arrays, due to a microphase separation between the PS block and the sol-gel/PEO phase. Field emission scanning electron microscopy (FESEM) and scanning probe microscopy (SPM) images showed that the uniformity and long-range order of the titania/PEO domains improved with increasing sol-gel precursor amount. Grazing incidence small-angle X-ray scattering (GISAXS) results indicate that the ordered structures exist over large length scales. Titania nanocrystal arrays of anatase modification were obtained by calcination at 600 degrees C for 4 h. After calcination, separated particles were observed for low and medium amounts of sol-gel precursors. Films with higher precursor amounts showed wormlike structures due to the aggregation between neighboring particles. Removal of the polymer matrix via UV treatment leads to highly ordered arrays of amorphous titania while retaining the domain size and interparticle distance initially present in the hybrid films. Photoluminescence (PL) properties were investigated for samples before and after calcination. The PL intensity increases with the increasing amount of sol-gel precursor. Bands at 412 nm were ascribed to self-trapped exitons and bands at 461 and 502 nm to oxygen vacancies, respectively. Uncalcined or UV-treated samples also showed PL properties similar to calcined samples, indicating that the local environment of the titanium atoms is similar to the environment of the crystalline anatase modification.     

Aerosol-assisted fabrication of mesoporous titania spheres with crystallized anatase structures and investigation of their photocatalitic properties

We demonstrate practical aerosol-assisted approach to synthesize spherical mesoporous titania particles with high surface areas. Scanning electron microscopy observation of the spray-dried products clearly shows spherical morphology. To remove surfactants and enhance crystallinity, the spray-dried products are calcined under various temperatures. The crystalline structures inside the particles are carefully detected by wide-angle XRD measurements. With increase of the calcination temperatures, anatase crystal growth proceeds and transformation from anatase to rutile is occurred. The effect of various calcination temperatures on the mesostructures is also studied by using N₂ adsorption desorption isotherms. The mesoporous titania particles calcined at 350, 400, and 500 °C exhibit type IV isotherms with a capillary condensation step and shows a hysteresis loop, which is a characteristic of mesoporous materials. The reduction in the surface areas and the pore volumes is confirmed by increasing the calcination temperatures, while the average pore diameters are increased gradually. This is attributed to the distortion of the mesostructures due to the grain growth of the anatase phase and the transformation to the rutile phase during the calcination process. As a preliminary experimental photocatalytic activity, oxidative decomposition of acetaldehyde under UV irradiation is examined. The mesoporous titania calcined at 400 °C shows the highest photocatalytic activity, due to both high surface area and well-developed anatase crystalline phase.     

Synthesis of nanosized TiO2/SiO2 particles using microwave processes and their photocatalytic activity on the decomposition of orange II

The nanosized titania and TiO₂/SiO₂ particles were prepared by the microwave-hydrothermal method. The effect of physical properties TTIP/TEOS ratio and calcination temperature has been investigated. The major phase of the pure TiO₂ particle is of the anatase structure, and a rutile peak was observed above 800°C. In TiO₂/SiO₂ particles, however, no significant rutile phase was observed, although the calcination temperature was 900°C. No peaks for the silica crystal phase were observed at either silica/titania ratio. The crystallite size of TiO₂/SiO₂ particles decreases as compared to pure TiO₂ at high calcination temperatures. The TiO₂/SiO₂ particles show higher activity on the photocatalytic decomposition of orange II as compared to pure TiO₂ particles.     

碳/氧化物复合物中碳层对氧化物相变的影响

碳/氧化铝(氧化钛)复合物具有独特的物理化学性质,在吸附和催化过程中有广泛应用.复合物中碳层对氧化物的相变有重要影响.在高温下通氧气焙烧碳/γ-Al2O3复合物可使γ-Al2O3迅速转变为α-Al2O3;而在惰性气氛中,碳层可显著抑制氧化铝的相变与烧结.碳/氧化钛体系中,碳层可明显提高氧化钛在惰性气氛中的热稳定性,在800℃以下碳层能有效阻止锐钛矿相向金红石相的转变;在含氧气氛中控制焙烧条件可将碳层完全除去而基本不影响氧化钛的物相组成及织构.因此,碳层可作为一种特殊的表面修饰剂,既可在高温下抑制氧化物的相变,又可避免在氧化物中引入掺杂元素.     

掺锌的TiO2纳米粉的结构相变及发光性质

采用溶胶-凝胶法制备了掺锌的TiO₂纳米粉末,并用XRD、TEM、TG和DSC等技术考察了掺入的锌对TiO₂的锐钛矿→金红石结构相变的影响.研究结果表明,锌的掺入可促进TiO₂的结构相变,使相变温度显著降低.纳米态TiO₂存在室温光致发光现象,在TiO₂的纳米粉中掺入适量的锌,可显著增强体系的发光强度.     

Surfactant mediated synthesis of spherical binary oxides photocatalytic with enhanced activity in visible light

Spherical silica and zirconia mixed titania and pure titania samples were prepared in presence of cetyltrimethylammonium bromide (CTAB) through controlled hydrolysis of corresponding metal alcoxides. Effect of surfactant amount and calcinations temperature on morphology, surface area and photocatalytic activity is studied using PXRD, SEM, FTIR, Solid state UV-vis spectroscopy and BET surface area. It is well observed that in presence of 2 mol% CTAB, uniform sized spherical oxide particles can be synthesized. However, increasing or decreasing the surfactant amount does not favor the spherical particle formation. Material synthesis in presence of CTAB not only helps in the spherical particle formation but also increases the surface area and visible light absorption. Studies on photocatalytic lead removal with respect to calcination temperature indicate that the calcination at 500 degrees C is most suitable for the best photocatalytic activity. Mixing of zirconia and silica helps in anatase phase stabilization even at 900 degrees C calcination. Accordingly low decrease in surface area even at 900 degrees C calcination is observed. Due to the phase stabilization and higher surface area binary oxide materials showed comparatively better photocatalytic activity even after calcination at 900 degrees C. So it can be concluded that present synthesis approach can produce uniform sized spherical binary oxide materials with better photocatalytic activity in visible light.     

Microcalorimetric investigation of high-surface-area mesoporous titania samples for CO2 adsorption

Mesoporous titania powders were synthesized using the triblock copolymer F127 (PEO(106)PPO(70)PEO(106)) as a surfactant template. Two different procedures (ammonia and/or low-temperature treatment at 393 K) were successfully applied to stabilize the mesoporous structure, resulting in significantly increased surface areas and pore volumes with respect to those of the untreated titania powders. Three of these samples were chosen for further investigation by adsorption microcalorimetry. These samples are characterized by high surface areas (varying between 340 and 141 m (2) g (-1)) and a varying degree of crystallization (anatase phase). The samples were compared to nanosized anatase particles treated to 873 K. The adsorption microcalorimetry was carried out using nitrogen and carbon dioxide at 77 and 303 K, respectively, to gain complementary information about the surfaces. Nitrogen at 77 K showed, for the three samples, adsorption enthalpies at low coverage of similar values, approximately -19 to -22 kJ mol (-1), indicating that the probe gas interacts with similar energetic surface sites. Two distinct energetic regions are observed, the first of which increases with increasing pretreatment temperature, which can be related to increased sample crystallinity. The adsorption of carbon dioxide at 303 K showed high adsorption enthalpies (up to approximately 65-80 kJ mol (-1)), highlighting strong interactions of the carbon dioxide with the titania surface at low pressures. Finally, the CO(2) adsorption properties of the titania samples (adsorbed amount and enthalpies of adsorption) are compared with those of other nanosized adsorbents. This comparison shows the potentiality of mesoporous titania powders for the adsorption of CO(2).     

Synthesis of bimodal porous structured TiO2 microsphere with high photocatalytic activity for water treatment

In this work bimodal structured titanium dioxide (TiO₂) microsphere has been prepared from commercial TiO₂ powder and nano-sized titania gel via sol–gel spray-coating technique. Crystallization and transformation behavior of titania gel were investigated. The results revealed that the crystallization and transformation of anatase particles were substantially affected by the concentration of solvent and calcination temperature. Anatase crystallite size of 10 nm was obtained at mole ratio of solvent/precursor 50/1 and calcination temperature of 450 °C. The prepared nano-sized titania gel was embedded within the core (commercial TiO₂, P25) during the spraying process. The prepared TiO₂ microsphere was characterized using X-ray diffractometer (XRD), scanning electron microscope (SEM), field emission electron microscope (FESEM) and micropore analysis. The photocatalytic activity was monitored by following the degradation of phenol with activity benchmarked against commercial P25 (Degussa). The increase of photocatalytic activity of TiO₂ microsphere was attributed to the nano-sized anatase crystallite which has been incorporated into the TiO₂ microsphere.     

Preparation of titania-coated polystyrene particles in mixed solvents by ammonia catalysis

A mixed-solvent method was developed to coat polystyrene (PS) spheres with smooth, homogeneous shells of amorphous titania by ammonia catalysis. The TEM images showed that, in the presence of ammonia, the thickness of titania shells could be controlled in the range of 8-65 nm by varying the concentration of titanium tetrabutoxide (TBOT) in the ethanol/acetonitrile mixed solvents with an appropriate volume ratio. The diffusion-controlled mechanism of the mixed solvents and the catalysis mechanism of ammonia were investigated. After the calcination of core-shell particles for 2 h at 500 degrees C, spherical hollow titania shells could be obtained, and the surfaces of the particles remained quite smooth and homogeneous. The XRD analysis indicated that calcination promoted the transformation of amorphous titania into an anatase phase.     

Low temperature design of titanium dioxide anatase materials decorated with cyanuric acid for formic acid photodegradation

The influence of cyanuric acid (CA) on the structural, textural, electronic, morphological properties and the photocatalytic activity of titanium dioxide materials (TNCA) were herein evaluated. TNCAs samples were prepared through the sol gel method. The novelty of this work that cyanuric acid; the so far most recalcitrant molecule, is used here as reservoir of nitrogen. The synthesis of TNCAs nanomaterials are performed at low temperature in presence of quaternary ammonium as co-catalyst for anatase growth. Samples were characterized by means of nitrogen adsorption-desorption isotherms at 77 K, X-ray diffraction (XRD), Infrared (ATR), Raman, diffuse reflectance ultraviolet-visible, photoluminescence (PL) and electron paramagnetic resonance (EPR) spectroscopies, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The photocatalytic activities of TNCAs and their free counterpart nanomaterials were then evaluated in the photocatalytic degradation of formic acid (FA) as model molecule under UV.X-ray and Raman show success of anatase phase formation at low temperature without any post-calcination. IR-ATR analysis confirms CA grafting onto TiO₂ identified by formation of vibration band between Ti and triazine. SEM mapping shows that C, O, Ti, and N are homogeneously distributed in the nanomaterial. Nitrogen adsorption-desorption measurements at 77 K show developed textural properties; the heat of N₂ adsorption seems to be affected by CA loading. PL and UV-visible spectroscopies show simultaneously (i) electron trapping by the oxygen vacancy identified by Raman spectroscopy by redshift of Eg1 mode and (ii) the hole is confined by nitrogen. Therefore, the excited electron can move from TiO₂ VB to the new sublevels initiated by the introduction of nitrogen which results in quenching of the photoluminescence intensity. The photocatalytic activity of the various TNCAs nanomaterials increases versus CA loading. The highest k_LH of TNCA2 (5 wt%) could be explained by short migration time conjugated with lower bulk recombination of the photogenerated electron hole.     

Photoluminescence of anatase and rutile TiO2 particles

Nonaqueous reactions between titanium(IV) chloride and alcohols (benzyl alcohol or n-butanol) were used for the synthesis of anatase TiO2 particles, while rutile TiO2 particles were synthesized in aqueous media by acidic hydrolysis of titanium(IV) chloride. The X-ray diffraction measurements proved the exclusive presence of either the anatase or the rutile phase in prepared samples. The photoluminescence of both kinds of particles (anatase and rutile) with several well-resolved peaks extending in the visible spectral region was observed, and the quantum yield at room temperature was found to be 0.25%. Photon energy up-conversion from colloidal anatase and rutile TiO2 particles was observed at low excitation intensities. The energy of up-converted photoluminescence spans the range of emission of normal photoluminescence. The explanation of photon energy up-conversion involves mid-gap energy levels originating from oxygen vacancies.     

Effects of Ti Addition on Alumina/Titania Composite Aerogels Synthesized by Sol–Gel Process and Supercritical Ethanol Drying

Alumina/titania composite aerogels with different titania contents were synthesized by the sol–gel process and supercritical ethanol drying. The structures and morphologies of synthesized aerogels were analyzed by X‐ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetry, and N₂ adsorption–desorption tests. Supercritical ethanol drying induced the crystallization of titania, which prompted the transformation of the structure from pseudoboehmite to γ‐Al₂O₃ . Reversely, alumina retarded the anatase‐to‐rutile transformation of titania. The content of titania significantly affected the structure and morphology of alumina/titania composite aerogels. A high content of titania (≥40%) resulted in the phase separation of titania particles, which grew to form the anatase phase octahedral particles with well‐developed facets. When the titania content was low, titania particles could be homogeneously dispersed in alumina particles to form spherical clusters with the poor crystallinity. Titania particles were in the anatase phase, and no rutile phase was formed until the temperature rose to 1000°C. In addition, titania addition resulted in a decrease in the specific surface area (SSA) of alumina aerogels because the SSA of titania was lower than that of alumina aerogels.     

Preparation and characterization of perfluorosulfonic resin/titania hybrid transparent films

Preparation and characterization of perfluorosulfonic resin/titania organic-inorganic hybrid films were presented. The transparent hybrid films were prepared by hydrothermal treatment at low temperature of a mixed solution of tetrabutyl titanate and perfluorosulfonic resin with the help of acetylacetone. The characterization was carried out by SEM,XRD,FT-IR,UV-Vis and TGA. The results showed that the perfluorosulfonic resin/titania hybrid transparent films were composed of titania particles dispersed in the perfluorosulfonic resin matrix very well and the titania was of anatase phase. Its diameter de-creased with increasing weight ratio of titania to perfluorosulfonic resin.     

The effect of F-doping and temperature on the structural and textural evolution of mesoporous TiO2 powders

Mesoporous F⁻-doped TiO₂ powders were prepared by hydrolysis of titanium tetraisopropoxide (TTIP) in a mixed NH₄F-H₂O solution. Effects of F⁻ ion content and calcination temperatures on the phase composition and porosity of mesoporous titania were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and BET surface areas. The results showed the BET surface area (S_BET) of the pure and doped powders dried at 100°C ranged from 260 to 310 m²/g as determined by nitrogen adsorption. With increasing calcination temperatures, the S_BET values of the calcined titania powders decreased due to the increase in crystalline size. The pore size distribution was bimodal with fine intra-particle pore and larger inter-particle pore as determined by nitrogen adsorption isotherms. The peak pore diameter of intra-particle pore increases with increasing F⁻ ion content. At 700°C, all the titania powders exhibit monomodal pore size distributions due to the complete collapse of the intra-particle pores. The crystallization of anatase was obviously enhanced due to F⁻-doping at 400°C and 500°C. Moreover, with increasing F⁻ ion concent, F⁻ ions not only suppressed the formation of brookite phase at low temperature, but also prevented phase transition of anatase to rutile at high temperature.     

EPR investigation of TiO2 nanoparticles with temperature-dependent properties

An in situ electron paramagnetic resonance (EPR) study has been carried out for anatase (Hombikat UV100) and rutile TiO(2) nanoparticles at liquid helium (He) temperature (4.2 K) under UV irradiation. Rutile titania was synthesized by ultrasonic irradiation with titanium tetrachloride (TiCl(4)) as the precursor. XRD and Raman results evidence the crystallinity of titania phases. The nature of trapped electrons and holes has been investigated by EPR spectroscopy under air and vacuum conditions. Illumination of TiO(2) powder (anatase and rutile) at 4.2 K resulted in the detection of electrons being trapped at Ti(4+) sites within the bulk and holes trapped at lattice oxide ions at the surface. The stability of electron traps was very sensitive to temperature in both phases of TiO(2). The annealing kinetics of the EPR detected radicals has been studied from 4.2 K to ambient temperature and also for calcined titania particles from 523 to 1273 K.     

Fabrication of Porous Titania Particles from Water-in-Oil Emulsions for the Applications of Photocatalyst

In this study, polystyrene nanospheres were synthesized by dispersion polymerization using batch-type reactor for the self-organization with precursor materials inside emulsion droplets. Mechanical homogenization was applied for the emulsification of the polymeric nanospheres and titanium diisopropoxide bis (acetylacetonate) to produce the macroporous titania particles by evaporation-driven self-assembly. Similarly, spherical titania crystallites could be synthesized via self-organization using triblock copolymer instead of polymeric latex beads after successive calcination. The morphologies of the porous particles were observed using electron microscope, and the crystallinity of the porous titania particles was analyzed by powder x-ray diffraction. As a demonstrative application, the macroporous titania microparticles with anatase phase were adopted as photocatalyst for the decomposition of Rhodamine B, and excellent catalytic performance was observed with higher rate constant compared to the result from commercial titania nanocolloid. Collectively, our macroporous titania microparticles were found to be safe catalytic materials for human body minimizing the skin toxicity since the size of the catalysts is in the micron-range.     

Preparation of Ordered Mesoporous Alumina‐Doped Titania Films with High Thermal Stability and Their Application to High‐Speed Passive‐Matrix Electrochromic Displays

Ordered mesoporous alumina‐doped titania thin films with anatase crystalline structure were prepared by using triblock copolymer Pluronic P123 as structure‐directing agent. Uniform Al doping was realized by using aluminum isopropoxide as a dopant source which can be hydrolyzed together with titanium tetraisopropoxide. Aluminum doping into the titania framework can prevent rapid crystallization to the anatase phase, thereby drastically increasing thermal stability. With increasing Al content, the crystallization temperatures tend to increase gradually. Even when the Al content doped into the framework was increased to 15 mol %, a well‐ordered mesoporous structure was obtained, and the mesostructural ordering was still maintained after calcination at 550 °C. During the calcination process, large uniaxial shrinkage occurred along the direction perpendicular to the substrate with retention of the horizontal mesoscale periodicity, whereby vertically oriented nanopillars were formed in the film. The resulting vertical porosity was successfully exploited to fabricate a high‐speed and high‐quality passive‐matrix electrochromic display by using a leuco dye. The vertical nanospace in the films can effectively prevent drifting of the leuco dye.     

Low-temperature synthesis and microstructural control of titania nano-particles

Nanocrystalline titania powders were synthesized at low temperature (⩽100°C) by a sol–gel method that achieved fine control of particle size and polymorph fraction. X-ray diffraction (XRD), transmission electron microscopy (TEM) and UV–Vis spectroscopy were used to characterize the phase assemblages, crystal size and band gap of the powders. It was demonstrated that larger, well-ordered titania crystals can be obtained by increasing aging temperature and time. These processing parameters can be adjusted to select specific polymorphs from the gel precursors with particular size and shape. The quantum size effect was observed in the size-controlled nanocrystalline titania particles, leading to a blue shift in UV absorption with decreasing in particle size. The anatase to rutile transformation, which may proceed with brookite as a transition phase, is dependent on both particle size and surface structure of the nascent crystals.     

Synthesis, characterization, and photocatalytic activity for hydrogen evolution of nanocrystalline mesoporous titania prepared by surfactant-assisted templating sol-gel process

Nanocrystalline mesoporous titania was synthesized via a combined sol-gel process with surfactant-assisted templating method, treated under various calcination conditions, and evaluated for its photocatalytic activity through photocatalytic hydrogen evolution from an aqueous methanol solution. In this synthetic method, applied surfactant template molecules functioned as both mesopore-forming and gelation-assisting agents. The resulting products were methodically characterized by TG-DTA, XRD, N₂ adsorption-desorption, diffuse reflectance UV-Vis spectra, SEM, and TEM analyses. The partial phase transformation from anatase to rutile occurred beyond calcination temperature of 600 °C and anatase-rutile transition kinetics was also investigated. The calcination conditions and crystalline phases existing in the products exerted significant effect on the photocatalytic hydrogen evolution activity. The activity of the synthesized titania treated under appropriate calcination conditions was considerably higher than that of commercial titania powders, Ishihara ST-01 and Degussa P-25. It is clearly seen that the introduction of mesopore into titania photocatalyst substantially improved the photocatalytic performance.     

含 TiO2(B) 介孔氧化钛材料的制备、特性和应用

 综述了近年来本课题组依据材料化学工程研究思想, 对含 TiO2(B)(一种比金红石和锐钛矿相结构更松散的氧化钛晶型) 介孔氧化钛材料在制备、结构和性能方面所取得的研究进展. 该介孔材料由二钛酸钾经水合、离子交换和热处理得到, 具有良好原子尺度晶格匹配界面特征的锐钛矿和 TiO2(B) 核壳结构. 研究表明, 该介孔材料在兼备高比表面积、高晶化孔壁和高热稳定性的同时, 还表现出良好的纳米颗粒担载稳定性, 在光催化、油品加氢精制、药物载体、固体酸催化和电化学电容器等方面已凸显出良好的应用潜力和推广价值. 目前该新型含 TiO2(B) 介孔氧化钛材料已经实现低成本、规模化制备.