Mobility of important toxic analytes in urban dust and simulated air filters determined by sequential extraction and GFAAS/ICP-OES methods

The modified BCR three-step sequential extraction procedure has been applied to homogenized urban dust samples and to simulated air filters loaded with the prepared urban dust via the wet deposition procedure. This work has been focused on comparative study of the distribution of trace elements in both samples and evaluation of the factors influencing the reliability of results with respect to the proposed extraction procedure. Extracted chemical fractions were analyzed by ICP-OES and GFAAS depending on the concentration levels of investigated trace elements As, Cd, Cr, Mn, Ni, and Pb, selected according to their adverse effect on the human health. Statistically evaluated results indicate significant differences between the extracted portions of analytes in urban dust and simulated air filters, where the mobility of some analytes in simulated air filters was higher than that in urban dust samples. The impact of surfactant Triton X-100 (0.05 vol. %) on the extraction procedure was also investigated. Presented at the XVIIIth Slovak Spectroscopic Conference, Spišská Nová Ves, 15–18 October 2006.     

Up‐and‐down shaker‐assisted ionic liquid‐based dispersive liquid—liquid microextraction of benzophenone‐type ultraviolet filters

Sun protection is an important part of our lives. UV filters are widely used to absorb solar radiation in sunscreens. However, excess UV filters constitute persistent groups of organic micropollutants present in the environment. An environmentally friendly ionic‐liquid‐based up‐and‐down shaker‐assisted dispersive liquid?liquid microextraction device combined with ultra‐performance liquid chromatography coupled with photodiode‐array detection has been developed to preconcentrate three UV filters (benzophenone, 2‐hydroxy‐4‐methoxybenzophenone, 2,2′‐dihydroxy‐4‐methoxybenzophenone) from field water samples. In this method, the optimal conditions for the proposed extraction method were: 40 μL [C₈MIM][PF₆] as extraction solvent and 200 μL methanol as disperser solvent were used to extract the UV filters. After up‐and‐down shaking for 3 min, the aqueous solution was centrifuged at 5000 rpm speed, then using microtube to collect the settled extraction solvent and using ultra‐performance liquid chromatography for further analysis. Quantification results indicated that the linear range was 2–1000 ng/mL. The LOD of this method was in the range 0.2–1.3 ng/mL with r² ≥ 0.9993. The relative recovery in studies of different types of field water samples was in the range 92–120%, and the RSD was 2.3–7.1%. The proposed method was also applied to the analysis of field samples.     

A comparison of direct thermal desorption with solvent extraction for gas chromatography-mass spectrometry analysis of semivolatile organic compounds in diesel particulate matter

Direct thermal desorption-gas chromatography-mass spectrometry (DTD-GC-MS) is a technique that is finding application in the characterisation of the semivolatile organic carbon fraction of ambient and combustion source particulate matter (PM) collected on filters. In this study, three DTD-GC-MS methods were assessed and compared to a conventional solvent extraction method for analysis of a mixture of target analytes in solution and of diesel PM collected on quartz filters. The target analytes included n-alkanes, hopanes, steranes and polycyclic aromatic hydrocarbons. This study showed that while the three DTD-GC-MS methods were generally comparable to the solvent extraction method, (1) the choice of calibration strategy and calibration materials has a significant impact on the measured accuracy of a method; (2) very large variations were seen in all methods for the more volatile compounds such as C₁₀ to C₁₃ n-alkanes and naphthalene; (3) accuracy, defined as difference from the known concentration of a liquid sample, ranged from 5% to 32%; (4) precision, defined as the relative standard deviation, ranged from 4% to 16%. The average difference of DTD-GC-MS results from the solvent extraction results for the diesel PM filters ranged from 20% to 40%. This difference was driven by the large number of target analytes present at relatively low concentrations (<25 pg/mm²) and their corresponding higher variability. Differences in performance among the compound classes were noted. Minimum detection limits for the DTD-GC-MS methods were on the order of 0.1 to 1 pg/mm² and were as good as or better than those obtained for the solvent extraction method.     

Association Behavior of 4-Acylpyrazolone Derivative and Tertiary Amine of High Molecular Weight in Antagonistic Synergistic Extraction of Palladium

To find an effective extraction and removal method for palladium(II), which is one of the main fission products from an acidic nuclear spent fuel solution, the extraction behavior of palladium(II) from a nitric acid medium by an acidic chelating extractant, 1-phenyl-3-methyl-4-trifluoroacetylpyrazolone-5-one (HPMTP) and a tertiary amine of high molecular weight, tri-n-octylamine (TOA), has been studied by spectrophotometry. A noticeable antagonistic extraction effect was observed in the extraction system under the given conditions. To understand this phenomenon, a preliminary investigation was performed to explain the mechanism of this reaction. According to the theory of corresponding solutions (TCS), the association reaction between HPMTP and TOA is proposed in the organic phase. An associated species, HPMTP·TOA, formed through hydrogen bonding in a chloroform medium might be the main reason why an antagonistic extraction effect occurred. The association constant between HPMTP and TOA was calculated to be 2.86±0.05.     

Determination of organic UV filters in water by stir bar sorptive extraction and direct analysis in real-time mass spectrometry

A screening method for analyzing environmental waters contaminated with UV filters using direct analysis in real-time mass spectrometry (DART-MS) was developed. To demonstrate the suitability of DART-MS a test set of seven organic UV filters, namely benzophenone-3 (BP-3), ethylhexyl dimethyl p-aminobenzoate (OD-PABA), 4-t-butyl-4′-methoxydibenzoylmethane (BM-DBM), homomethyl salicylate (HMS), 2-(ethylhexyl) salicylate (EHS), octocrylene (OC), and 4-methylbenzylidene camphor (4-MBC), was defined. In the first step, standard solutions of the analytes prepared in methanol were investigated in order to determine optimum parameters for the DART-MS. Because of the very low concentrations of UV filters expected in environmental water samples, a pre-concentration step using stir bar sorptive extraction was performed. DART-MS allows the direct, simple and rapid semi-quantitative analysis of the analytes enriched on the surface of the polydimethylsiloxane-coated stir bars. The optimized method provided calibration curves with correlation coefficients R > 0.959, repeatability from 5% (for 4-MBC) to 30% (for BM-DBM) relative standard deviation and limits of detection lower than 40 ng L⁻¹ for all analytes. Finally, real lake water samples from locations with typical leisure activities were analyzed. Results obtained with the developed DART-MS method were cross-checked by confirmatory analysis using thermodesorption gas chromatography mass spectrometry (TD-GC-MS). Thereby, it could be demonstrated that both analytical methods provide comparable concentrations for the UV filters in the lake water samples.     

Methodological study of extraction procedures applied to urban particulate matter

The modified BCR three-step sequential extraction procedure has been applied to two different samples of urban particulate matters (PM). The distribution of selected trace elements As, Cd, Cr, Mn, Ni, Pb, Zn was investigated and, in a comparative study, the presence of common organic air filters in extraction procedures was evaluated. Analytes in separate fractions were determined by ICP-OES and GFAAS, respectively, depending on concentration levels. While, due to air filters, a significant increase of some analytes mobility in individual fractions has been observed in case of the jet-milled PM (tunnel Letna), but in case of the PKC sample such effect was not found. The analyte impurities built in some filters has been tested, and the impact on the reliability of analyte results has been discussed. The arsenic species occurrence and their stability in presence of air filters (size 47 mm) were investigated in both urban PM samples as well, using HPLC-ICP-MS technique. Water soluble and by three-step BCR procedure extractable arsenic forms are shown in chromatograms     

Chemometrics assisted dispersive liquid–liquid microextraction for quantification of seven UV filters in urine samples by HPLC‐DAD

In the present study, dispersive liquid–liquid microextraction followed by high performance liquid chromatography‐diode array detection has been developed as simple, rapid, accurate, and efficient sample preparation method for simultaneous determination of seven organic UV filters in urine samples. The influence of the main effects as well as their interactions was studied through a 2^(6–2) fractional factorial design. The candidate parameters were: type and volume of dispersant and extraction solvents, sample pH, and salt concentration. Under final optimal conditions, the analytes were extracted from 5 mL of samples by addition of 0.5 mL of acetonitrile (dispersing solvent) containing 70 μL of carbon tetrachloride (extraction solvent), without modifying the pH of the solution and applying the (+1) level of salt concentration (10% w/v NaCl). The assay was linear (R² > 0.997), relative recoveries ranged from 86.9 up to 97.3% and the LOQs between 3 and 45 ng mL^?1 were obtained. The intra‐ and interday RSDs were lower than 5 and 8% at the middle point of the linear range, respectively. The proposed method was successfully applied to different volunteer urine samples and it was shown that the extraction efficiency was not affected by the type of urine samples.     

Coencapsulation of Butyl‐Methoxydibenzoylmethane and Octocrylene into Lipid Nanocarriers: UV Performance,Photostability and in vitro Release

The coencapsulation of two UV filters, butyl‐methoxydibenzoylmethane (BMDBM) and octocrylene (OCT), into lipid nanocarriers was explored to develop stable cosmetic formulations with broad‐spectrum photoprotection and slow release properties. Different types of nanocarriers in various concentrations of the two UV filters were tested to find the combination with the best absorption and release properties. Solid lipid nanoparticles (SLNs) and nanostructured lipid carriers (NLCs) have been the two types of lipid nanocarriers used. The NLCs were based on either medium chain triglycerides (MCT) or squalene (Sq). The following physicochemical properties of the nanocarriers have been evaluated: particle size, morphology, zeta potential (ZP), entrapment efficiency, loading capacity, and thermal behavior. The nanocarriers have been formulated into creams containing low amounts of UV filters (2.5% BMDBM and 1% OCT). The best photoprotection results were obtained with the cream based on NLCs prepared with MCT, having a sun protection factor (SPF) of 17.2 and an erythemal UVA protection factor (EUVA–PF) of 50.8. The photostability of the encapsulated BMDBM filter was confirmed by subjecting the nanocarriers‐based creams to in vitro irradiation. The prolonged UV‐protection efficacy was coupled with a slow in vitro release of the synthetic UV filters, which followed the Higuchi release model.     

Recycling of Palladium and Selected Metal Ions from Simulated Spent Catalysis Waste Solution Using Novel Dithiodiglycolamides Derivatives

The present study focusing on design and evaluation of series of eight new structurally related dithiodiglycolamides (DTDGA) as a novel promising solvent extraction reagents. The influence of the nature of the alkyl chain on the distribution ratio of Pd(II) was investigated. Both N, N-di-hexyl-N′, N′-di-octyldithiodiglycolamide (DHDODTDGA) and N, N-di(2-ethylhexyl)-N′, N′-dioctyldithiodiglycolamide (DEHDODTDGA) were chosen and applied to perform the selective recovery and separation of Pd(II) from certain commonly associated elements such as Pt(IV), Rh(III), Fe(III), Cr(II), Mn(II), Zr(II), and Ni(II) contained in hydrochloric acid solutions using n-dodecane as diluent. A systematic investigation has been carried to understand the extraction behavior of Pd(II) using the synthesized extradant. The extraction equilibrium of Pd(II) was obtained within 3–4 min. The investigated extractants showed quantitative extraction of Pd(II) at ～ 4 M HCl. The main extracted species of Pd(II) at 3.5 M HCl is Pd.DTDGA and IR spectra of the extracted species have been also studied. The other investigated metals ions were found poorly extracted under the same extraction contortions. Quantitative back-extraction of Pd(II) in the organic phase was obtained in single contact using thiourea solution. The obtained results make the novel synthesized ligands a promising candidates for selective recovery and separation of Pd(II) from spent catalyst dissolver (SSCD) solution.

     

Comparison of Extraction Techniques and Surfactants for the Isolation of Total Polyphenols and Phlorotannins from the Brown Algae Lobophora variegata

Abstract

Surfactant-mediated extraction (SME), pressurized liquid extraction (PLE), and enzyme-assisted extraction (EAE) have been compared to improve the isolation of phlorotannins from the brown algae Lobophora variegata. Enzymatic treatment with Alcalase 2.4?L FG, Carezyme 4500?L, protease from Streptomyces griseus, pectinase from Aspergillus niger, Celluclast 1.5?L, protease from Bacillus licheniformis; surfactant extraction with triacetin and guaiacol and PLE with ethanol:water as extracting solvent, have been studied in terms of total phenolic content by the Folin–Ciocalteu method and total phlorotannin content using the DMBA assay. The results showed that SME yields the highest amount of phenols and phlorotannins by using food grade guaiacol as the surfactant. An extraction protocol was developed to maximize the amount of extract obtained from L. variegata. The effects of various parameters such as the type of surfactant, efficacy of surfactant, and optimum pH, on the extraction efficiency of polyphenols were examined. The simultaneous use of the enzyme and surfactant was also investigated. However, a synergistic effect between the enzymes and the surfactant for the extraction of polyphenols has not been observed. Considering total phenols and total phlorotannins in the extract, the extraction yield were obtained for total phenols as SME?>?EAE?>?PLE and for total phlorotannins as SME?>?PLE?>?EAE.     

Unprecedented Inversion of Selectivity and Extraordinary Difference in the Complexation of Trivalent f Elements by Diastereomers of a Methylated Diglycolamide

When considering f elements, solvent extraction is primarily used for the removal of lanthanides from ore and their recycling, as well as for the separation of actinides from used nuclear fuel. Understanding the complexation mechanism of metal ions with organic extractants, particularly the influence of their molecular structure on complex formation is of fundamental importance. Herein, we report an extraordinary (up to two orders of magnitude) change in the extraction efficiency of f elements with two diastereomers of dimethyl tetraoctyl diglycolamide (Me₂-TODGA), which only differ in the orientation of a single methyl group. Solvent extraction techniques, extended X-ray absorption fine structure (EXAFS) measurements, and density functional theory (DFT) based ab initio calculations were used to understand their complex structures and to explain their complexation mechanism. We show that the huge differences observed in extraction selectivity results from a small change in the complexation of nitrate counter-ions caused by the different orientation of one methyl group in the backbone of the extractant. The obtained results give a significant new insight into metal–ligand complexation mechanisms, which will promote the development of more efficient separation techniques.     

Optimization of extraction process and characterization of water-soluble polysaccharide (Galactomannan) from Algerian biomass; Citrullus colocynthis seeds

In this work, the optimization of extraction of polysaccharides from Citrullus colocynthis curd polysaccharides (CCPs) is investigated by using the analysis of variance. For this aim, a chemical extraction method has been developed in order to be able to isolate CCPs at high level of purity. The extraction was performed by using boiling water at different extraction times (30, 60 and 120?min), extraction temperatures (50, 75 and 100°C), and a material ratio (30, 60 and 100?g/ml), for maximum polysaccharide extraction. The 3-D response surface plot and the contour plot derived from the mathematical models are used to determine the optimal conditions. The optimum extraction conditions are as follows: extraction temperature 100°C, extraction time 120?min and the ratio of water 30?ml/g. Under these conditions, the experimental final mass is 210.6?mg which is very close to the predicted value (209.46?mg) with a regression coefficient of 94.01%. In addition, the existence of the polysaccharide has been confirmed by the characterization of the galactomannan obtained from C. colocynthisis obtained by Fourier transform infrared-attenuated total reflection, IR-Raman spectroscopy and X-ray diffraction.     

Photostability and phytotoxicity of selected sunscreen agents and their degradation mixtures in water

The study on the photostability of six UV filters in aqueous solution was combined with investigations on the phytotoxicity of the produced degradation mixtures. During the exposure to artificial sunlight over 72 h, the degradation of three of the UV filters evaluated was observed with half-lives between 20 and 59 h. The structural changes of iso-amylmethoxy-cinnamate (IAMC), ethylhexyl-methoxy-cinnamate (EHMC), and 4-methylbenzyliden camphor (4-MBC) occurred during irradiation were consistent with isomerisation and polymerization (IAMC and EHMC) whereas 2-ethylhexyl-4-(dimethylamino)benzoate (OD-PABA) was degraded. The analysis of the UV filters and their degradation products was performed by stir bar sorptive extraction (SBSE) followed by thermodesorption–gas chromatography–mass spectrometry (TD-GC-MS) or liquid desorption–liquid chromatography–mass spectrometry (LD-LC-MS). The phytotoxicological potential of the UV filters was examined in vitro by evaluating reproduction inhibition of the chlorophyte microalgae Scenedesmus vacuolatus. Excess toxicity was calculated by comparing experimental derived median efficiencies after log-logistic modeling to predict effects assuming narcotic mode of action. Benzophenone-3 (BP-3) showed 43-fold higher toxicity than theoretically predicted and a more specific mode of action was assumed. The other UV filters tested indicated toxicity in the range of modeled narcosis. For IAMC, EHMC, and OD-PABA the phytotoxicity of their photodegradation mixtures was followed over time. Phytotoxicity decreased directly with the reduction of the parent substance from the solution. Five of the tested UV filters do not represent a risk at least for algae. Octocrylen and 4-MBC were found to be photostable but few toxic to algae. EHMC, IAMC, and OD-PABA were fast degraded during UV radiation and the phytotoxicity of the corresponding degradation mixtures was low and decreased onward during exposure. Thus, for the UV filters studied, it could be confirmed that sunlight can account noticeably for decontamination and detoxification of contaminated water. However, due to its potential accumulation in combination with a specific mode of action, BP-3 may imply probable environmental risks at least to algae. This study emphasizes the need of a combined chemical and toxicological evaluation for a reliable risk assessment concerning degradation processes exemplified here for UV-protecting agents.     

Determination of UV filters in packaging by focused ultrasonic solid-liquid extraction and liquid chromatography

A focused ultrasonic solid-liquid extraction (FUSLE) and high performance liquid chromatography (HPLC) with a diode array detector (DAD) is proposed for the determination of ten fat-soluble UV filters in packaging. FUSLE technique is relatively new and has been used for the extraction of a few analytes; such as polycyclic aromatic hydrocarbons and other organic pollutants. In this work, it has been demonstrated that FUSLE is a useful, fast and simple extraction methodology for UV filters because the complete extraction was carried out with just 6ml of tetrahydrofuran and in only one cycle of 30s. The developed method has been validated and applied to the analysis of polyethylene-based multilayer packaging samples. The FUSLE-based method allows the sensitive detection of most of the UV-filters in polyethylene, with limits of detection between 0.4 and 8.5ngmg(-1) (except for BDM). Intra and inter-day relative standard deviation values were below 5 and 14%, respectively, except for MBP. In addition, the proposed method was more efficient than tetrahydrofuran extraction under reflux for 2.5h for all the analytes except for EMT and BDM. Therefore, the developed method can be used to establish the absorption capability of different types of packaging and this information will be very useful in packaging selection.     

Precise and Sensitive Water Soluble Ion Extraction Method for Aerosol Samples Collected on Polytetrafluoroethylene Filters

Abstract

The widely used aerosol collection filters composed of polytetrafluoroethylene (Teflon) present a problem in the extraction of water soluble ions from the collection surface due to the hydrophobic nature of the Teflon. A method is presented for the extraction and analysis of water soluble ions from Teflon aerosol filters which is efficient and sensitive. This method uses a direct application of ethanol to the filter surface to decrease the surface tension of the filter and allow a dilute HC10, solution to contact the collection surface and extract any water soluble ions. This study compares this extraction method with other extraction methods currently being used. The results obtained from the extraction of water soluble ions from the Teflon filters were also compared to the results obtained from quartz filters collected on a colocated high volume sampler. From these studies, it is concluded that the hydrophobic nature of the Teflon filters makes the complete dissolution of water soluble ions exceptionally difficult and that the prewetting of the Teflon filters with ethanol minimizes dissolution and extraction problems.     

Development of new polar monolithic coatings for stir bar sorptive extraction

Polar vinyl monomers have been used for the synthesis of several polymer monoliths, to serve as novel coatings for stir bar sorptive extraction; the monovinyl monomers 2‐hydroxyethyl methacrylate (HEMA) and poly(ethylene glycol) monomethacrylate) (PEGMA) were copolymerized with (apolar) divinylbenzene (DVB) and/or pentaerythritol triacrylate (PETRA), both of which are cross‐linking agents. After the optimization of the most important synthesis parameters, which included the ratio between total monomers and porogen, the nature of the porogen, and the monomer ratios, inter alia, three mechanically stable, polar monolithic coatings for stir bar sorptive extraction were obtained that were based on poly(HEMA‐co‐DVB), poly(HEMA‐co‐PETRA), and poly(PEGMA‐co‐PETRA). Thereafter, and in order to evaluate the hydrophilicity of the resulting monoliths, they were applied as materials in the stir bar sorptive extraction of a group of emerging pollutants with a wide range of polarities. The results showed that both the poly(HEMA‐co‐DVB) and poly(PEGMA‐co‐PETRA) materials could be used to extract both polar and nonpolar compounds by stir bar sorptive extraction, in an effective manner. Taking into account the desired chemical and morphological properties, as well as the extraction efficiencies, the poly(PEGMA‐co‐PETRA) material seemed to be a particularly promising monolith for application as a novel coating in stir bar sorptive extraction.     

Radiochemical extraction of mercury(II) from acidic chloride solutions using dialkylsulphides

The liquid-liquid extraction behavior of Hg(II) from aqueous acidic chloride solutions has been investigated by tracer techniques using dialkylsulphides (R₂S) namely, dibutylsulphide (DBS) and dioctylsulphide (DOS) as extractants. These extraction data have been analyzed by both graphical and theoretical methods by taking into account complexation of the metal ion in the aqueous phase with inorganic ligands and all plausible complexes extracted into the organic phase. The results clearly indicate that Hg(II) is extracted into xylene as HgCl₂ ^. nDBS/nDOS (where n = 2 and 3). The equilibrium constants of the extracted complexes have been deduced by non-linear regression analysis. The separation possibilities of Hg(II) from other metal ions viz. Ca(II), Mg(II), Ba(II) and Fe((III), which are present in the industrial wastes of the chlor-alkali industry has also been discussed.     

Systematic study of the extraction of metals using N-benzoyl-N-phenylhydroxylamine

The extraction of Y, La, Ce(III), Gd, Th, Fe(III), Co(II), Cu, Zn, Cd, Hg, In and Tl (I=0.1;T=20±2°C) with N-benzoyl-N-phenylhydroxylamine (N-BPHA) in chloroform has been studied in order to determine the composition, and the extraction and two-phase stability constants of the extracted chelates. The dissociation constant of N-BPHA in aqueous solution has also been determined.     

Orthogonal array design for the optimization of ionic liquid-based dispersive liquid-liquid microextraction of benzophenone-type UV filters

In the present study, dispersive liquid-liquid microextraction (DLLME) using an ionic liquid (IL) as the extractant was successfully developed to extract four benzophenone-type UV filters from the different water matrices. Orthogonal array experimental design (OAD), based on five factors and four levels (L(16)(4(5))), was employed to optimize IL-dispersive liquid-liquid microextraction procedure. The five factors included pH of sample solution, the volume of IL and methanol addition, extraction time and the amount of salt added. The optimal extraction condition was as follows. Sample solution was at a pH of 2.63 in the presence of 60 mg/mL sodium chloride; 30 μL IL and 15 μL methanol were used as extractant and disperser solvent, respectively; extraction was achieved by vortexing for 4 min. Using high-performance liquid chromatography-UV analysis, the limits of detection of the target analytes ranged between 1.9 and 6.4 ng/mL. The linear ranges were between 10 or 20 ng/mL and 1000 ng/mL. This procedure afforded a convenient, fast and cost-saving operation with high extraction efficiency for the model analytes. Spiked waters from two rivers and one lake were examined by the developed method. For the swimming pool water, the standard addition method was employed to determine the actual concentrations of the UV filters.     

Development of a micro-mixer-settler for nuclear solvent extraction

Nuclear solvent extraction was traditionally performed with packed columns, pulse columns, mixer-settlers and centrifugal extractors. However for rapid separations at micro-flow level, micro mixer-settlers were desired and in the past, few of them were actually designed and operated in nuclear solvent extraction research. In the current era of micro-reactor and microchannel devices, there is a renewed interest for micro-mixer-settlers for costly solvents and specialty solutes where small flow-rate is not an issue. In this article, development of a simple but effective micro-mixer-settler for nuclear solvent extraction is reported. The developed unit was tested with 30% TBP/n-dodecane/nitric acid system and in both the regimes of mass transfer c → d (mass transfer from continuous phase to dispersed phase, also written as c → d) and d → c (mass transfer from dispersed phase to continuous phase, also written as d → c) nearly 100% efficiency was observed in extraction as well as stripping modes of operation.