CeO2-ZrO2包覆石墨粉增强铝基复合材料的制备与耐蚀性能

采用非均匀成核法,在机械搅拌条件下通过硝酸亚铈和氧氯化锆水解生成无定形氧化铈、氧化锆对石墨进行表面包覆,利用扫描电镜、 X射线衍射和XPS对所得样品进行了表征,通过搅拌铸造法制备了氧化铈/锆包覆石墨颗粒增强铝基复合材料,并对复合材料耐蚀性能进行了初步研究. SEM和XPS表明,氧化铈/锆在石墨表面形成了均匀、致密的纳米级包覆层,氧化铈/锆通过与铝液的反应性润湿提高了石墨颗粒与铝液的润湿性,阻止了石墨与铝发生化学反应. 测试结果表明,氧化物的包覆基本抵消了由于石墨的添加而降低复合材料的腐蚀电位,也降低了腐蚀电流(两个数量级).     

La2O3对Mo5Si3/MoSi2复合材料的改性研究

通过粉末冶金方法制备了Mo5Si3/MoSi2和La2O3/Mo5Si3/MoSi2复合材料,探讨了其烧结工艺.检测了其密度、维氏硬度、抗弯强度和断裂韧性,运用X射线衍射仪和扫描电镜（SEM）研究了La2O3对Mo5Si3/MoSi2复合材料显微结构和力学性能的改性影响.结果表明,La2O3/Mo5Si3/MoSi2复合材料的合理烧结温度为1600 ℃,比MoSi2材料提高了100 ℃; 稀土氧化物的加入细化了晶粒,且明显提高了材料的致密度、维氏硬度和抗弯强度; 其强化机制为细晶强化和弥散强化; 韧化机制为细晶韧化、裂纹偏转、裂纹分支和微桥接.     

聚合物/量子点纳米复合材料的制备

量子点具有优异的光电性能,聚合物具有性质稳定、质轻、可加工性好等优点;将聚合物和量子点复合可综合两者的优点,同时还可使量子点的稳定性得以大幅度提高。得到的聚合物/量子点纳米复合材料应用领域广;其制备方法主要有简单易操作的直接分散法、在聚合物中原位生成量子点的原位生成法、在有量子点存在的聚合场所引发有机单体聚合的原位聚合法、层-层组装法以及在量子点表面直接修饰聚合物的表面直接修饰法。本文就这些制备方法进行了概要综述,并对各种方法的特点进行了总结。     

壳聚糖-铝氧化物复合材料的制备、表征及吸附性能

以壳聚糖和异丙醇铝为原料通过化学键合法制备了壳聚糖-铝氧化物复合材料,通过FTIR、SEM、TG等方法对其进行了表征,考察了其对水溶液中Cu3+的吸附性能.结果表明,在制备的复合材料中,铝与壳聚糖发生了键合作用,无机铝氧化物均匀分散在壳聚糖中,复合材料的热稳定性得到显著提高;与壳聚糖及壳聚糖和Al2O3的混合材料相比,复合材料对Cu2+的吸附性能明显改善,其中吸附率比壳聚糖提高了13%,吸附量可达146mg/g.     

镍基蒙脱土/聚苯胺纳米复合材料的制备与表征

首先通过化学氧化法合成了导电聚苯胺,再将聚苯胺引入镍基蒙脱土层间,合成了镍基蒙脱土/聚苯胺纳米复合材料,并用FTIR、XRD、TEM对其结构进行了表征与分析。结果表明,聚苯胺已进入蒙脱土层间,并使蒙脱土片层间距增大。测定了复合前后材料的电导率并对其进行了合理的解释。     

树脂基稀土-铁系超磁致伸缩复合材料的制备与压应力效应研究

采用粉末粘结-磁场成型法制备了树脂基稀土-铁系超磁致伸缩复合材料(Giant magnetostrictive particle composite,GMPC),并对样品在不同压应力下的磁致伸缩系数进行了测量,当样品中的TeDyFe合金颗粒尺寸为0~200μm、质量分数为90%时,其磁致伸缩系数于外加磁场达到266 kA.m-1时即已趋近饱和,饱和磁致伸缩系数达623×10-6;当施加在样品纵向方向上的预压应力为5 MPa时,此时样品的饱和磁致伸缩系数最高,为662×10-6,比未加预压应力时样品的饱和磁致伸缩系数高39×10-6,表明所制得的实验样品具有一定的压应力效应,并且压应力效应在较低压力下起积极作用,在较大压力下则产生消极作用。     

铝基复合材料中不同形态碳分析方法的研究

本文研究铝基复合材料中碳元素不同存在形式（总碳、游离碳、碳化硅）的检测方法。 采用高频感应燃烧红外法测定总碳（2.00%～6.00%）,酸溶过滤分离-高频红外法测定游离碳（0.10%～1.50%）,重量法测定碳化硅(1%～35%)的含量。以上三个方法的精密度试验RSD%（n=8）最大分别为4.2%、1.2%、0.51%,测定游离碳和碳化硅(SiC)样品的加标回收率分别是98.5%～100.2%,99%～101%。 这三种方法都快速、可靠,已应用于铝基复合材料的实际分析工作中。     

MoS_2纳米片及其增强环氧树脂基复合材料的制备与性能研究

以液相分散法为基础制备了MoS2纳米片悬浮液.对该悬浮液进行了吸光性能和荧光性能表征;结果显示悬浮液荧光信号明显增强;同时得到增加超声时间、降低离心转速、采用粒径较大的块状粉末和加入球磨工艺这些因素是可以提高悬浮液的吸光度的优化工艺条件.采用微区荧光测试测得了单个MoS2纳米片的荧光光谱,其主峰位置在652 nm,对应的带隙能量是1.9 e V;还对单个纳米片进行退火处理,其荧光信号在退火后有所增强.对MoS2纳米片进行了AFM和SEM表征显示大部分纳米片的平面尺寸在几百纳米,厚度约为几纳米.另外,将MoS2纳米片悬浮液与E51环氧树脂混合,制备了MoS2纳米片增强环氧树脂基复合材料.对该复合材料进行了荧光性能和拉伸性能测试.结果显示复合材料的荧光信号也明显增强;且经退火后,因为复合材料内部残余热应力的关系,该复合材料的荧光信号的峰值位置出现移动.同时,该复合材料的韧性也有提升.     

以除尘灰分离碳粉制备活性炭的新方法研究

利用除尘灰分离碳粉作原料,采用添加适量化学药品KOH的方法制备颗粒活性炭。研究了随着KOH加入量的变化,活性炭性能和对苯的吸附量的变化规律,以及KOH的加入量对活性炭的微晶结构和表面形貌产生的影响。并探讨了添加剂在活性炭制备的炭化和活化阶段的产生的影响。实验结果表明在KOH加入量为1.5%时,碘吸附值、比表面积和对苯的吸附量达到最高值,KOH过量反而对吸附性能有负面影响。     

PU/MOMMT纳米复合材料的制备与研究

纳米复合材料由于其纳米尺寸效应，表面效应以及纳米粒子与基体界面间强的相互作用，具有优于相同组分常规复合材料的力学、热学等性能，引起了人们的广泛关注。用纳米材料改性聚合物，制备纳米复合材料是获得高性能高分子复合材料的重要方法。1998年以来，Pinnavaia等首先制备了聚氨酯，蒙脱土（PU／MMT）纳米复合材料，研究了有机蒙脱土在聚醚中的分散性。其后Chen等将聚羟基己内酯/蒙脱土（PCL／MMT）纳米复合材料加入到PCL和二苯基甲烷-4，4＇-二异氰酸酯（MDI）合成的预聚体与1，4-丁二醇扩链反应后的溶液中，制备了PU／MMT纳米复合材料。少量PCL／MMT的引入可使复合材料的综合性能大幅提高。     

A Sequential Extraction Method Measures the Toxic Metal Content in Fly Ash from a Municipal Solid Waste Incinerator

The purpose of this research was to develop an optimized pretreatment procedure for toxic metals (Pb, Cd, Zn and Cu) content in fly ash from a municipal waste incinerator. In addition, modified sequential extraction procedures were used to characterize the chemical composition of the fly ash samples. The sequential extraction resolved the fly ash elements into the following chemical forms: soluble, exchangeable, carbonate, oxide, organic, and silicate compounds. Certified reference city waste incineration ash (BCR.176) was used as target ash samples. A H₂O₂+HNO₃+HF mixed acid digestion solution with a low temperature evaporation procedure was selected as optimal for the fly ash digestion. The digested solution was analyzed by inductively coupled plasma mass spectrometry (ICP‐MS), which effectively determined the concentrations of the toxic metal elements in BCR.176. Except for Cd, the recovery of Pb, Zn, and Cu under H₂O₂+HNO₃+HF digestion and their sequential extraction procedures were higher than 95%. The relative standard deviations (RSD) for recoveries of the four elements were within 10%. Furthermore, the sequential extraction procedure's results provided information on the potential mobility of the studied elements. Most of the Cd was bound to water‐soluble and carbonate material in the fly ash samples. Most of the Pb, Zn, and Cu was released to carbonates and bound to organic matter in the fly ash samples.     

HRGC-LRMS测定垃圾焚烧炉布袋飞灰中的二噁英类物质

利用高分辨气相色谱-低分辨质谱(HRGC-LRMS)测定了某垃圾焚烧厂布袋飞灰中的二(口恶)英类物质,结果表明对于测定二(口恶)英类浓度相对较高的垃圾飞灰而言,采用HRGC-LRMS是一种可行的方法,回收率在74％～114％之间。该飞灰样品中以二(口恶)英为主,呋喃的含量相对较低,二(口恶)英／呋喃值为4.6,二(口恶)英类物质总量为211.7ng／g,折算到毒性当量为0.69ngI-TEQ／g。     

Energy Recovery from Municipal Solid Waste in Small Communities

The heating values of municipal solid waste generated in three towns with a population of less than 50 000, situated in Galicia (Spain), were measured with a static bomb calorimeter. Samples of raw refuse were burnt either as received or after sorting of the different combustible components. A study was made of samples from controlled and uncontrolled landfills. The calorific values were compared with those corresponding to a commercial residual derived fuel in order to study the possibility of using municipal solid waste as a source of recovered energy. This revised version was published online in July 2006 with corrections to the Cover Date.     

Overall Kinetics of Heat Treatment of Municipal Solid Waste

A mathematical model of the overall kinetics of heat treatment of municipal solid waste was developed. The model considers the main initial substances and products of the reaction of municipal solid waste treatment at high temperatures (1300–1500°C) in a tubular flow reactor.     

Plasma-Assisted Treatment of Municipal Solid Waste: A Scenario Analysis

Small-scale thermal treatment of municipal solid waste (MSW) was investigated using mass and energy balances based on the assumption of thermodynamic equilibrium. A typical average MSW composition from the literature was used as basis for modelling of a one ton per day waste gasification facility (plant). Syngas production by pyrolysis, stoichiometric O₂ addition and auto-thermal (gasification with oxygen and/or air where no external heat input is required) combustion were considered. These cases were evaluated for production of electricity only, and steam. From purely thermodynamic considerations, it was observed that auto-thermal oxygen gasification produces the most electricity (47.00 kWe) and oxygen plasma gasification produces a positive net amount (4.07 kWe) on a 1 ton per day scale. Although auto-thermal air gasification also produces a net positive amount, the calorific value of the syngas is too low to fuel an internal combustion engine. As expected, the amount of steam generated by the different scenarios is high due to higher process efficiencies. The close-coupled auto-thermal oxygen process proved to be the most efficient. The cost of additional oxygen generation was however not taken into account, and may change the picture significantly.     

利用粉煤灰合成低硅铝比NaP分子筛

以粉煤灰分级处理获得的硅铝组分Na2SiO3和NaAlO2为原料,通过水热反应制备了NaP型分子筛.考察了钠盐不同阴离子和有机空间位阻剂对NaP分子筛制备的影响,优化了水热合成NaP分子筛的工艺参数,采用X射线衍射(XRD)、扫描电子显微镜(SEM)和BET方程对NaP分子筛产品的晶型、形貌和孔容进行分析表征,对NaP分子筛吸附水溶液中Ni2+的性能进行了评价.结果表明,合成NaP分子筛的最佳原料摩尔比为n(Na2O)∶n(SiO2)∶n(Al2O3)∶n(H2O)=3.23∶1.95∶1∶226,反应温度为120℃,晶化时间为8h.当钠盐中阴离子为Br-时,可增大P型分子筛产率并提高其纯度.添加有机空间位阻剂三乙醇胺(TEA)[n(TEA)∶n(Al2O3)=1∶1]时,合成的P型分子筛粒径较小且具有较大的孔容,此时对应的Ni2+去除率较高,可达96.2%.     

Ethanol Production from the Organic Fraction Obtained After Thermal Pretreatment of Municipal Solid Waste

In this work, the use of organic fraction from municipal solid waste (MSW) as substrate for ethanol production based on enzymatic hydrolysis was evaluated. MSW was subjected to a thermal pretreatment (active hygienization) at 160?°C from 5 to 50 min. The organic fiber obtained after 30 min was used as substrate in a simultaneous saccharification and fermentation (SSF) and fed-batch SSF process using cellulases and amylases. In a fed-batch mode with 25% (w/w) substrate loading, final ethanol concentration of 30 g/L was achieved (60% of theoretical). In these conditions, more than 160 L of ethanol per ton of dry matter could be produced from the organic fraction of MSW.     

Municipal Solid Waste Landfill Leachate Treatment and Electricity Production Using Microbial Fuel Cells

Microbial fuel cells were designed and operated to treat landfill leachate while simultaneously producing electricity. Two designs were tested in batch cycles using landfill leachate as a substrate without inoculation (908 to 3,200 mg/L chemical oxygen demand (COD)): Circle (934 mL) and large-scale microbial fuel cells (MFC) (18.3 L). A total of seven cycles were completed for the Circle MFC and two cycles for the larger-scale MFC. Maximum power densities of 24 to 31 mW/m² (653 to 824 mW/m³) were achieved using the Circle MFC, and a maximum voltage of 635 mV was produced using the larger-scale MFC. In the Circle MFC, COD, biological oxygen demand (BOD), total organic carbon (TOC), and ammonia were removed at an average of 16%, 62%, 23%, and 20%, respectively. The larger-scale MFC achieved an average of 74% BOD removal, 27% TOC removal, and 25% ammonia reduction while operating over 52 days. Analysis of the microbial characteristics of the leachate indicates that there might be both supportive and inhibiting bacteria in landfill leachate for operation of an MFC. Issues related to scale-up and heterogeneity of a mixed substrate remain.     

磷酸提取-高效液相色谱-氢化物发生原子荧光光谱法分析垃圾焚烧飞灰中无机砷形态

以H3PO4为提取剂,通过微波提取的方法,采用高效液相色谱-氢化物发生原子荧光光谱联用技术(HPLC-HG-AFS)实现了垃圾焚烧飞灰中砷的价态测定.重点探究了H3PO4存在下,使用HPLC-HG-AFS测定无机砷(As(Ⅲ)和As(Ⅴ))价态的色谱条件.结果表明,当使用(NH4)2HPO4为流动相时,H3PO4的存在会对As(Ⅴ)的分析造成不利影响,增大流动相流速对改善这种状况几乎没有效果;而使用Na2HPO4-KH2PO4混合溶液(pH 6.864)作为流动相时,可以显著降低H3PO4对As(Ⅴ)分析的干扰.在优化的色谱条件下,As(Ⅲ)和As(Ⅴ)可在5 min内实现分离,检出限分别为0.063和0.110 μg/L.在标准物质加标回收实验中,各价态回收率良好(86.5％～102.5％).利用本方法对来自4个垃圾焚烧电厂的飞灰样品进行分析,发现垃圾焚烧飞灰中的砷主要以As(Ⅴ)的形式存在.