聚苯乙烯/蒙脱土熔融插层复合的研究

用熔融法制备了聚苯乙烯／蒙脱土插层复合材料，用Ｘ 射线衍射、ＤＳＣ等手段研究了复合材料的结构与性能．聚苯乙烯熔体不能插层于钠基蒙脱土中，但能插层于经有机化合物处理过的蒙脱土中．     

尼龙6/蒙脱土纳米复合材料的等温结晶动力学研究

用ＤＳＣ法研究了熔体插层制备的尼龙６／蒙脱土纳米复合材料的等温结晶行为．结果表明,加入少量的蒙脱土可明显提高尼龙６的结晶速率,降低球晶径向生长的单位面积表面自由能．从Ａｖｒａｍｉ方程和Ｈｏｆｍａｎ理论出发,得出蒙脱土纳米粒子的存在可明显改变尼龙６的结晶行为     

A green and efficient deoximation using H202 catalyzed by montmorillonite-K10 supported COC12

Oximes were oxidized to the corresponding carbonyl compounds in good to high yields by environmentally friendly and green oxidant, H202 catalyzed by montmorillonite K-10 supported cobalt（Ⅱ） chloride.     

TiO2/蒙脱石纳米复合物中TiO2的结构相变

以钛酸丁酯和季铵盐改性有机蒙脱石为原料,采用原位水解法和原位脱羟法制备了TiO2/蒙脱石纳米复合物。采用X射线衍射(XRD)、拉曼光谱(Raman)表征了不同焙烧温度下TiO2/蒙脱石纳米复合物中TiO2的结构相变,并与不同焙烧温度下纯TiO2的结构相变进行对比。结果发现TiO2/蒙脱石纳米复合物中TiO2从锐钛矿相开始转变为金红石的最低温度要比纯TiO2从锐钛矿开始相转变为金红石的最低温度高200℃,且在焙烧温度1 200℃时还存在锐钛矿相,而纯TiO2在焙烧温度800℃时就全部转换为金红石相。TiO2/蒙脱石纳米复合物中TiO2和纯TiO2的平均晶粒度都随焙烧温度升高而增大,但TiO2/蒙脱石纳米复合物中TiO2的平均晶粒度要小于相同温度下焙烧纯TiO2的平均晶粒度。表明蒙脱石结构层的硅氧结构抑制了TiO2晶型由锐钛矿相向金红石相的转变,进而使相变温度升高,同时阻碍了晶体的生长。     

丁二烯/苯乙烯/4-乙烯基吡啶共聚物蒙脱土嵌入混杂材料的研究

用聚合物乳液与蒙脱土的水分散体共混共凝的方法制备混杂材料.在混合过程中乳胶粒与蒙脱土晶层相互穿插,用盐酸絮凝,带正电的共聚物能够嵌入带负电的蒙脱土层间.萃取实验发现在混杂材料中蒙脱土吸附了大量的共聚物,说明蒙脱土晶层与共聚物之间存在静电吸附作用.XRD实验发现在混杂材料中蒙脱土的晶层结构发生了膨胀,并且变得混乱,而在共混物中蒙脱土晶层结构几乎不变.用TEM观察在混杂材料中蒙脱土晶层均匀分散于共聚物基体中,蒙脱土的层间距大于6nm.共聚物嵌入蒙脱土的层间,受到蒙脱土晶层的限制作用,共聚物的T_g发生了变化.交联以后的混杂材料的性能比共聚物有了较大的提高,蒙脱土晶层在共聚物基体中起到很好的补强作用.     

尼龙6/蒙脱土纳米复合材料的结晶行为

用广角Ｘ 射线衍射（ＷＡＸＤ）、差示扫描量热仪（ＤＳＣ）、小角激光散射（ＳＡＬＳ）等手段研究了尼龙６／蒙脱土纳米复合材料的结晶行为．结果表明分散在尼龙６基体中的蒙脱土纳米粒子起成核剂的作用．蒙脱土的表面改性增加了蒙脱土和尼龙６分子之间的界面粘接，它具有阻碍尼龙６结晶的作用，使结晶活化能增加     

环氧树脂/蒙脱土/咪唑纳米复合材料固化行为的研究

运用非平衡态热力学涨落理论预估了环氧树脂 有机蒙脱土 咪唑插层型纳米复合体系在不同温度及不同有机蒙脱土用量时的固化行为 ,理论曲线与动态扭振的实验有良好的符合 .实验表明 ,有机蒙脱土的加入 ,使凝胶化时间tg 缩短 ,固化速率加快 ,但对凝胶点后的固化反活化能ΔH影响不大     

聚苯乙烯/蒙脱土纳米复合材料的制备及结构研究

以可与苯乙烯发生共聚的阳离子表面活性剂乙烯苄基二甲基十八烷基氯化铵(VOAC)为插层处理剂改性蒙脱土(VC18-MMT),有机蒙脱土在超声波强剪切作用以及乳化剂作用下预分散在乳化剂溶液中,然后引入苯乙烯单体进行原位乳液聚合制备聚苯乙烯/蒙脱土纳米复合材料.采用XRD和TEM对纳米复合材料的结构进行了表征.结果表明,绝大多数的蒙脱土被剥离成单个片层均匀的分散在聚合物基体中;动态力学分析表明,纳米复合材料的储能模量和玻璃化温度均有所增加,而动态损耗有所降低;接枝在蒙脱土片层上的聚合物通过与锂离子进行阳离子交换反应提取下来,采用GPC和NMR对接枝聚合物的结构进行了表征,结果表明,接枝聚合物是较基体分子量低且分布很宽的苯乙烯和乙烯苄基二甲基十八烷基氯化铵的共聚物,计算表明每一个共聚物分子链上平均含有大约25个乙烯苄基二甲基十八烷基氯化铵分子.     

聚氨酯弹性体/蒙脱土纳米复合材料的合成与性能

采用聚氨酯本体预聚法 ,利用原位插层聚合合成了聚氨酯 蒙脱土纳米复合材料 .通过X 射线衍射(XRD)和Molau实验研究了蒙脱土在复合材料中的分散情况 .红外分析 (IR)表明随着蒙脱土含量的增加 ,复合材料羰基氢键减少 .动态力学分析 (DMA)以及差热分析 (DSC)结果说明随着蒙脱土含量的增加 ,材料的玻璃化温度降低 .聚氨酯纳米复合材料的拉伸强度和断裂伸长率同时提高 ,表现出较好的力学性能 .     

辐照法制备PVAc/蒙脱土纳米复合材料及其表征

蒙脱土有机化后 ,片层结构间距离增大 ,对有机物的亲和性有所增强 .采用VAc单体渗入有机化蒙脱土层间 .经γ 射线辐照引发原位插层聚合 ,使蒙脱土片层结构发生剥离 ,形成无机 有机纳米复合材料 .并用X衍射、红外光谱、扫描电镜以及透射电镜等现代测试手段对复合材料进行了表征     

Thermal stability and flame retardancy of LDPE/EVA blends filled with synthetic hydromagnesite/aluminium hydroxide/montmorillonite and magnesium hydroxide/aluminium hydroxide/montmorillonite mixtures

The combination of organophillised montmorillonite (MMT), synthetic hydromagnesite and aluminium hydroxide (ATH) as flame retardant system for polyethylene-based materials was studied and compared with a similar system with magnesium hydroxide, ATH and MMT. The thermal stability and the flame retardant properties were evaluated by thermogravimetric analysis (TGA), differential thermal analysis (DTA), limiting oxygen index (LOI) and cone calorimeter tests. The results indicated that the addition of montmorillonite makes it possible to reduce the total filler content to achieve the flame retardant requirements. The thermal stability of filled LDPE/EVA blends increases to a higher extent for the samples containing MMT. In the cone calorimeter tests we observed a reduction of the peak heat release rate for the sample containing montmorillonite in comparison with a sample with higher filler loading without this nanoclay. An increase of the stability of the char formed could be responsible for this favourable behaviour when montmorillonite is added.In addition, mechanical properties significantly improved for the composites containing montmorillonite both for the filler loading reduction and the reinforcement effect of the nanoclay.     

插层法悬浮聚合制PMMA/蒙脱土纳米复合材料

文献中蒙脱土的有机化处理一般采用一次插层法处理 ,本文采用了一种新的二次插层法 ,通过对一次插层法和二次插层法插层效果的比较 ,确定了二次插层法为一种理想的蒙脱土有机化方法 .经过MMA对蒙脱土插层的悬浮聚合 ,FT IR ,XRD和SEM等试验结果证明蒙脱土已经被有效地撑开 ,但发现蒙脱土的加入会降低聚合反应的转化率和聚合物的收率 ,悬浮聚合物颗粒的形态变得不规则 ,粒径也变大 .差热分析、溶解实验和应力 应变测试均表明蒙脱土的加入能提高PMMA的性能 ,蒙脱土的最佳用量在 3 %左右 .     

Selective formation of cumene on pillared clays by isopropylation of benzene

Summary Cumene is prepared selectively through an eco-friendly route using naturally available montmorillonite clay as the green catalyst. Pillaring of montmorillonite is done to improve the structural stability for long-term use. Alumina pillaring and the influence of mixed pillaring with zirconia and chromia on the structural as well as textural properties are characterized. Montmorillonite shows very high conversion, selectivity and regenerability upon pillaring towards isopropylation of benzene.     

Sorption/desorption of radionickel on/from Na-montmorillonite: kinetic and thermodynamic studies

In this work, Na-montmorillonite was used as a novel adsorbent for the sorption of Ni(II) from aqueous solutions. The sorption and desorption of Ni(II) on Na-montmorillonite was investigated as the function of pH, ionic strength, Ni(II) concentrations and temperature. The results indicated that the sorption of Ni(II) on Na-montmorillonite was strongly dependent on pH, ionic strength and temperature. The sorption of Ni(II) increases slowly from 22.1 to 51.4% at pH range 2–6.5, abruptly at pH 6.5–9, and at last maintains high level with increasing pH at pH > 9 in 0.1 mol/L NaNO₃ solutions. The Ni(II) kinetic sorption on Na-montmorillonite was fitted by the pseudo-second-order model better than by the pseudo-first-order model and the experimental data implies that Ni(II) sorption on montmorillonite were mainly controlled by the film diffusion mechanism. The Langmuir, Freundlich and D–R models were used to simulate the sorption data at three different temperatures (298.15, 318.15 and 338.15 K) and the results indicated that Langmuir model simulates the experimental data better than Freundlich and D–R models. The sorption–desorption isotherm of Ni(II) on montmorillonite suggested that the sorption is irreversible. The irreversible sorption of Ni(II) on montmorillonite indicates that montmorillonite can be used to pre-concentration and solidification of Ni(II) from large volumes of solution and to storage Ni(II) ions stably.     

环氧树脂/桐油酸酐/蒙脱土纳米复合材料固化动力学

环氧树脂/桐油酸酐/蒙脱土纳米复合材料固化动力学;固化反应;DSC     

中性红／蒙脱石／SnO2化学修饰电极制备及电化学性能

蒙脱石有很好的层状结构、大的表面积和优良的吸附性,与其它修饰材料(如Nafion)相比有较高的热稳定性和化学稳定性。是可以利用的廉价材料。用它制成的化学修饰电极(CME)已用于电催化、电有机合成等。 本文报道中性红(NR)/蒙脱石/SnO_2 CME的制备及其电化学性能。实验结果表明,用蒙脱石作修饰层材料,对电活性物质有很好的富集作用,制得的CME有较好的稳定性。虽然电活性物在蒙脱石膜界面的扩散系数较小,但由于在膜内有较高的浓度,因而制得的CME比空白     

新型茂钛催化剂原位本体聚合法制备间规聚苯乙烯/蒙脱土纳米复合材料

采用多碳氨基酸对蒙脱土进行改性 ,得到改性蒙脱土 (MTN) ,并使其层间距扩大 ,在一定条件下用茂金属催化剂Cp Ti(O C6 H4 F) 3 进行苯乙烯原位聚合发现 ,在氨基酸改性的蒙脱土存在下 ,茂金属催化剂活性有所提高 ,能制得间规聚苯乙烯 (sPS) 蒙脱土纳米复合材料 ,考察了蒙脱土用量对配位聚合的影响及该复合材料的形态结构、热稳定性和结晶性能     

Morphology and physical properties of polyethylene/silicate nanocomposite prepared by melt intercalation

Maleated polyethylene (PEMA)/silicate nanocomposites with a different aspect ratio of silicate and maleated PEMA/SiO₂ composite were prepared by melt intercalation. The nanocomposites with a high aspect ratio silicate (montmorillonite) showed a faster decrease in the terminal slope of the storage modulus and a steeper increase in complex viscosity than those with a low aspect ratio silicate (laponite) and SiO₂. The addition of montmorillonite increases the crystallization and the melting temperature of PEMA but decreases above 3 vol % of the silicate content because of the increased viscosity. The nanocomposite with montmorillonite showed the highest yield strength and secant modulus among the composites because of the highest aspect ratio of the filler. It also revealed strong interfacial adhesion with the matrix and orientation during tensile deformation. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1454–1463, 2002     

低剪切速率下聚乙二醇／KCl／蒙脱土分散体系的剪切稠化现象

用Hakke RS75流变仪研究了聚乙二醇（PEG）／KCl/蒙脱土分散体系的流变性 。结果发现，当KCl和聚乙二醇浓度在一定范围内时，体系随剪切速率增加，表现 出剪切稀释－剪切稠化－剪切稀释的复杂结构变化，并且剪切稠化发生在低剪切速 率区。KCl浓度继续增加，剪切稠化逐渐减弱。TME表明，蒙脱土分散体系中加入 KCl使得蒙脱土颗粒聚集，而聚乙二醇导致经微絮凝；二者同时加入，体系形成细 枝条状的空间稳定结构。     

Synthesis and Characterization of New Material——La/Zr/MMT Employed in Acetone Oxidation

A new material of zirconium pillared montmorillonite added with lanthanum （denoted as La/Zr/MMT） was prepared for acetone oxidation. Surface properties of the catalysts were investigated by means of XRD, TEM, TG-DTA and BET methods. The XRD result indicated that the interlayer space of the montmorillonite was enlarged from 1.57 to 4.85 um after the treatment with zirconium pillaring and the addition of lanthanum. N2 adsorption-desorption result showed that by the process of zirconium pillaring, the specific surface area of the sample was increased to 128.0 m^2/g, which was two times almost as large as pure montmorillonite. Simultaneously, the thermal stability was also enhanced. The activity of the new material on the total oxidation of acetone was investigated, and the results indicated that the catalytic activity of the montmorillonite was greatly improved. Over the sample of La/Zr/MMT, the T98 of acetone was obtained at 350 ℃, while it needs 400 ℃ over the pure montmorillonite. After 0.1% Pd was supported on the sample of La/Zr/MMT, the T98 decreased from 350 to 280 ℃, indicating the montmorillonite is a promising material for the control of some types of the volatile organic compounds such as acetone.