Renewable epoxidized cardanol‐based acrylate as a reactive diluent for UV‐curable resins

A novel kind of biobased monomer, epoxidized cardanol‐based acrylate (ECA), was successfully synthesized from cardanol via acrylation and epoxidization. The chemical structure was confirmed by Fourier transform infrared spectroscopy and proton nuclear magnetic resonance. Then, the ECA was employed to produce UV‐curable films and coatings copolymerized with castor oil‐based polyurethane acrylate. Compared to coatings from petroleum‐based diluent hydroxyethyl acrylate‐based castor oil‐based polyurethane acrylate resins, ECA‐based biomaterials exhibited a little inferior dilution ability but overcome the drawback of high volumetric shrinkage with a special lower value. Moreover, ultimate properties of the UV‐cured biomaterials such as thermal, mechanical, coating, swelling, and hydrophobic properties were investigated. The UV‐curing behavior was investigated using real‐time IR, and the overall double bond conversion was more than 90%. This biobased UV‐curable cardanol‐based diluent shows a promise in “green + green” materials technologies.     

Investigation of the tensile properties of “epoxy resin‐monomer” systems using cationic UV‐crosslinkable blends

The compatibility of cycloaliphatic and aromatic multifunctional epoxides with several epoxide resins allows the development of a wide range of cationic radiation‐curable formulations. The influence of different “epoxide resin‐monomer” systems UV‐cured in the presence of suitable cationic photoinitiators on the resulting physicochemical film properties was studied, and the results are stated. Copyright © 2004 John Wiley & Sons, Ltd.     

Thieno[3,4‐b]thiophene‐Based Organic Dyes for Dye‐Sensitized Solar Cells

New dipolar sensitizers containing an ethyl thieno[3,4‐b]thiophene‐2‐carboxylate (ETTC) entity in the conjugated spacer have been synthesized in two isomeric forms. These compounds were used as the sensitizers of n‐type dye‐sensitized solar cells (DSSCs). The best conversion efficiency (5.31 %) reaches approximately 70 % of the N719‐based (7.41 %) DSSC fabricated and measured under similar conditions. The ETTC‐containing compounds exhibit a bathochromic shift of the absorption compared to their thiophene congeners due to the quinoid effect, however, charge‐trapping at the ester group of ETTC was found to jeopardize the electron injection and lower the cell efficiency. Charge trapping is alleviated as the ester group of ETTC is replaced with a hydrogen atom, as evidenced from the theoretical computation.     

超支化聚(胺酯)的合成及其光固化性能研究

采用甲基丙烯酸酐直接改性和先以丁二酸酐或邻苯二甲酸酐酯化再以甲基丙烯酸缩水甘油酯改性所得到的甲基丙烯酸酯化超支化聚 (胺 酯 )齐聚物在光引发剂存在时紫外光辐照下发生快速聚合反应 ;反应速率和双键转化率随超支化分子的结构不同而变化 ;高度交联的涂膜具有较好的热学性能     

UV laser ablation of GdCa4O(BO3)3 (GdCOB) investigated by Fourier transform ion cyclotron resonance mass spectrometry

The ions generated by laser ablation (LA) of calcium and gadolinium oxoborate GdCa4O(BO3)3 (GdCOB) were investigated by Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS), a powerful tool for the characterization of ionic species produced by laser interaction with solid material. In order to better understand the matter transfer and the mechanism of thin film growth by pulsed-laser deposition (PLD), cationic and anionic clusters generated by UV laser ablation of GdCOB bulk material were studied. Laser ablation of GdCOB leads to the formation of various cluster ions which result from association of CaO, BO and B2O3 building blocks (BB) with different charge carriers (CC): H+, BO+, GdO+ in positive ion mode, and BO2-, OK-, OH-, Cl-, WO3- in negative ion mode. LA-FTICRMS investigations allow us to assign a valence state to each metallic atom included in each BB. A +II chemical state may be associated with calcium and +II and +III ones to boron. UV laser ablation of GdCOB therefore induces reduction processes of boron species in the gas phase. The oxygen reactive atmosphere used during PLD experiments allows the growth of stoichiometric thin films by fixation of oxygen on the ablated species.     

A humidity blocker approach to overcoming the humidity interference with cationic photopolymerization

A humidity blocker approach to overcoming the humidity interference with cationic photopolymerization is proposed and validated. Environmental humidity is one of the major interfering factors in cationic photopolymerization, and cationic photopolymerization is found to be inhibited by high humidity. When curing cycloaliphatic epoxide based cationic UV curable materials flexibilized by various reactive diluents under different humidity conditions, it was found that the more hydrophobic materials exhibited higher monomer conversion under higher humidity. To obtain cationic UV curable materials that are less influenced by humidity, a humidity blocker approach was proposed and monomer conversion of materials containing both hydroxy‐functional reactive diluents and epoxy‐siloxane were examined using real‐time FTIR. The hydroxy‐functional reactive diluents act as an internal hydroxyl source that enhances monomer conversion through chain transfer mechanism, and the hydrophobic epoxy‐siloxane acts as a humidity blocker, mitigating the inhibiting effects of humidity. Cationic UV curable materials with an optimized combination of these two components exhibited higher and more consistent monomer conversion under a range humidity conditions. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4344–4351, 2008     

Photoinitiators for UV and visible curing of coatings: Mechanisms and properties

The radiation curing industry is one of the most rapidly developing fields in the entire coatings industry. The low toxicity, cheapness, speed, control and ease of formulation and operation are some of the main advantages of this growing technology. UV and/or visible light radiation is used to induce photochemical polymerization or crosslinking of a monomer, oligomer or prepolymer formulation containing a certain type of unsaturation, such as an acrylic group, and an appropriate initiator. The latter is used to absorb the light energy and transform it into active species, such as radicals or ions, capable of inducing such reactions. Applications extend to general coatings for paper, board, wood, tapes, compact discs and holograms, inks, photoresists for imaging processes and adhesives for welding and sealing in electronic circuit boards. The photoinitiator is the key to the control of these processes and, in recent years, has seen many new developments. These include the need for water-soluble, co-reactive and polymeric structures with low migration rates, as well as cheaper UV/ visible sensitizers with enhanced speed. New and effective cationic systems are also on the scene and, although expensive, are attracting significant academic and commercial interest.     

Depth profile analysis of various titanium based coatings on steel and tungsten carbide using laser ablation inductively coupled plasma –“time of flight” mass spectrometry

A homogenized 193 nm ArF* laser ablation system coupled to an inductively coupled plasma-”Time of Flight”-mass spectrometer (LA-ICP-TOFMS) was tested for depth profiling analysis on different single-layer Ti based coatings on steel and W carbides. Laser parameters, such as repetition rate, pulse energy and spatial resolution were tested to allow optimum depth related calibration curves. The ablation process using a laser repetition rate of 3 Hz, 120 μm crater diameter, and 100 mJ output energy, leads to linear calibration curves independent of the drill time or peak area used for calibrating the thickness of the layer. The best depth resolution obtained (without beam splitter) was 0.20 μm per laser shot. The time resolution of the ICP-TOFMS of 102 ms integration time per isotope was sufficient for the determination of the drill time of the laser through the coatings into the matrix with better than 2.6% RSD (about 7 μm coating thickness, n = 7). Variation of the volume of the ablation cell was not influencing the depth resolution, which suggests that the depth resolution is governed by the ablation process. However, the application on the Ti(N,C) based single layer shows the potential of LA-ICP-TOFMS as a complementary technique for fast depth determinations on various coatings in the low to medium μm region.     

紫外光固化粉末涂料

紫外光（UV）固化粉末涂料综合了传统粉末涂料和辐射固化技术诸多优点，是涂料工业的前瞻性产品。本文介绍了紫外光固化粉末涂料的配制，固化机理，涂装工艺及潜在应用，并对其最新研究进展进行了综述。     

UV-光固化光纤涂料的研制

本文采用环氧丙烯酸酯与聚氨酯丙烯酸酯共混聚合的方法制备出新型的UV-光固化光纤涂料,其主要性能较好.研究了基体组成、引发剂、稀释剂以及固化工艺对UV-固化光纤涂料的光固化速度的影响.通过实验发现,环氧丙烯酸酯与聚氨酯丙烯酸酯的配比为 4:6～6:4、稀释剂的含量不大于20%时固化速度较快、性能较好,同时固化时灯距与固化膜厚度对固化速度的影响较大.     

可紫外光固化的超支化聚硅氧烷合成及固化研究

同线型聚硅氧烷聚合物相比，超支化聚硅氧烷聚合物具有低粘度、高反应活性和良好的相容性等特点，其中以制备超支化的聚硅氧烷基硅氧烷和聚烷氧基硅氧烷为主．对于超支化聚硅氧烷主要是以ABx（X=2～6）（其中A为双键，B为硅氢键）型单体为原料，在氯铂酸或Pt／C的催化下，通过硅氢加成反应一步制备，最终聚合物的端基（B）为硅氢键，而双键则完全反应，此外也可通过含不同数目烷氧基硅烷的水解缩合制备超支化聚硅氧烷．     

pH DEPENDENCE OF SENSITIZED PHOTOOXIDATION IN MICELLAR ANIONIC AND CATIONIC SURFACTANTS, USING THIAZINES DYES

Abstract— Our study of the kinetics of sensitized photooxidation, as a function of pH in anionic micellar systems using cationic dyes as sensitizers, shows that adsorption of the dye slows the protonation step of his triplet state. This observation has important implicaticins in interpretation of results in the so-called photodynamic effect in biological systems: using cationic dyes as sensitizers the rate of photooxidation for the same pH is different depending whether or not the medium allows adsorption of the dye.     

Comparison of one-step and two-step methods of polyimidization and substitution effect in the synthesis of new poly(ester-imide)s with bulky pendent group

New naphthalene-ring containing ester diamines, as new monomers for the preparation of polyimides were synthesized via two successive reactions. Nucleophilic reaction of 3,5-dinitrobenzoylchloride with 1-naphthol and 2-naphthol in the presence of sodium hydroxide led to the preparation of 1- and 2-(3,5-dinitrobenzoyloxy)naphthalene, respectively. Next step was reduction of them by hydrazine hydrate/Pd-C to produce 1- and 2-(3,5-diaminobenzoyloxy)naphthalene. All the prepared compounds were characterized by common spectroscopic methods. These ester containing aromatic diamines with pendent naphthalene group were used to prepare soluble polyimide copolymers via two different methods: catalyzed one-step high-temperature polycondensation in m-cresol, and two-step polycondensation in NMP and subsequent chemical dehydration. The obtained poly(ester-imide)s were characterized and their properties were studied. One-step and two-step methods for the preparation of five-membered ring polyimides were compared. Polymers prepared through one-step method showed higher yield and inherent viscosities and therefore better physical properties.     

The electronic structures and charge transfer properties of tetra(naphthalene‐dione)porphyrins and tetra(naphthalene‐dithione)porphyrins as dye‐sensitized solar cell skeleton

The p‐π conjugation of tetra(naphthalene‐dione)porphyrins and tetra(naphthalene‐dithione)porphyrins is clarified on the basis of density functional theory studies. When carbonyl/thionyl is introduced, π bonds on the molecular skeleton become strong–weak alternated, and the conjugation transforms from “benzene‐type” to “butadiene‐type.” The unidirectional photon‐induced current associated with the p‐π conjugation enables the light‐harvesting efficiency of this kind of molecular skeleton reaches 90% in the range of 300–800 nm. Therefore, these compounds are ideal alternative for panchromatic dye‐sensitized solar cells. © 2013 Wiley Periodicals, Inc.     

Effect of oxygen on laser-induced elemental fractionation in LA-ICP-MS analysis

Elemental fractionation poses serious difficulties in obtaining accurate concentration and isotope ratio data when using laser ablation sampling. One of the factors that control the extent of laser-induced elemental fractionation is the composition of sample carrier gas in the sample cell. This study demonstrates that the presence of small amounts of oxygen in the He carrier gas has a significant effect on elemental fractionation during the ablation of silicate (NIST 612 glass and zircon 91500) and sulphide (NiS fire assay) samples. The extent of elemental fractionation for a given amount of ablated material and concentration of oxygen in the He carrier gas was related to the volume of the plasma plume that forms above the sample surface. This indicates that an oxidation reaction takes place in the plasma plume. It has been reported that oxidation can affect the particle size distribution during laser sampling and hence change the extent of elemental fractionation. The purity of the carrier gas used in laser ablation-ICP-MS, as well as the amount of oxygen released from silicate and oxide samples during the ablation in "oxygen-free" ambient gas, is shown to contribute significantly to elemental fractionation.     

New Cisplatin Analogues—On the Way to Better Antitumor Agents

The clinical success of cisplatin (cis -diamminedichloroplatinum(II )) in antitumor chemotherapy has encouraged an all-out search for analogues with lower toxicity, improved therapeutic index and increased activity. Literally thousands of analogues, obtained by replacement of the ammine- and chloro-ligands by other amines and anionic ligands, respectively, have been systematically screened for activity in experimental tumor models. Some of these analogues have been selected for clinical evaluation, but only very few of them appear to be promising antitumor agents. More recently, cisplatin analogues have been designed and synthesized on the basis of, inter alia, the following considerations: 1) platinum complexes with carrier molecules as ligands should prove useful for achieving increasing drug concentration in tumor tissues; 2) platinum complexes with chemotherapeutic agents as ligands could afford polyfunctional drugs with synergistic action; 3) complexes containing more than one platinum atom might be more effective than complexes containing only one platinum atom; 4) platinum complexes could be used as sensitizers in radiation therapy. In this paper, we shall give a brief account of the “traditional” analogues, and then critically discuss what we believe could be the new trends in the design of cisplatin analogues.     

Capillary electrophoresis with post-column addition of terbium and sensitized lanthanide-ion luminescence detection for the determination of diflunisal and salicylic acid

A detection scheme based on the Post-column addition of terbium followed by sensitized luminescence detection has been developed. Two model Compounds- saliculic acid and diflunisa- were separated by capillary electophoresis in an alkaline phosphate buffer. A Solution containing terbium and CTAB was added post-column via a “home-built” reactor resulting in the rapid fromation of the strongly luminescent terbium-salicylic acid and terbium-diflunisal complexes in a reaction capillary. Following complexationn in the reaction capillarty, the 325 nm line from a HeCd laser was used to excite the analytes which efficiently transfer their energy to terebium. Resuulant luminescence of terebium was liner of 2 orders of magnitude. This novel and practical system enables the detection of micromolar concentrations of diflunisal and salicylic acid- a 10 fold improvement over UV absorbance detection in the same system. Post-column addition of terbium also eliminates the problems associated with strong adsorption of the lanthanide ion to the silica walls of the separation capillary and the formation of metal-ligand complexes with different coordination numbers.     

The maleimide modified epoxy resins for the preparation of UV‐curable hybrid coatings

In the present study, maleimide‐modified epoxide resin containing UV‐curable hybrid coating materials were prepared and coated on polycarbonate substrates in order to improve their surface properties. UV‐curable, bismaleimide‐modified aliphatic epoxy resin was prepared from N‐(p‐carboxyphenyl) maleimide (p‐CPMI) and cycloaliphatic epoxy (Cyracure‐6107) resin. The structure of the bismaleimide modified aliphatic epoxy resin was analyzed by FTIR and the characteristic absorption band for maleimide ring was clearly observed at 3100 cm^?1. Silica sol was prepared from tetraethylorthosilicate (TEOS) and methacryloxy propyl trimethoxysilane (MAPTMS) by sol–gel method. The coating formulations with different compositions were prepared from UV‐curable bismaleimide‐based epoxy oligomer and sol–gel mixture. The molecular structure of the hybrid coating material was analyzed by ²⁹Si‐CP/MAS NMR spectroscopy techniques. In the ²⁹Si CP/MAS NMR spectrum of the hybrid coating, mainly two kinds of signals were observed at ?68 and ?110 ppm that correspond to T³ and Q⁴ peaks, respectively. This result shows that a fully condensed structure was obtained. The thermal and morphological properties of these coatings materials were investigated by using TGA and SEM techniques. Hardness and abrasion resistance properties of coating materials were examined and both were found to increase with sol–gel precursor content of the coating. The photopolymerization kinetics was investigated by using RT‐IR. 70% conversion was attained with the addition of 15 wt% of BMI resin into the acrylate‐based coating formulation. It was found that the UV‐curable organic–inorganic hybrid coatings improved the surface properties of polycarbonate. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Organic Dyes with Various Electron‐Accepting Substituents for p‐Type Dye‐Sensitized Solar Cells

Four new donor‐π‐acceptor dyes differing in their acceptor group have been synthesized and employed as model systems to study the influence of the acceptor groups on the photophysical properties and in NiO‐based p‐type dye‐sensitized solar cells. UV/Vis absorption spectra showed a broad range of absorption coverage with maxima between 331 and 653 nm. Redox potentials as well as HOMO and LUMO energies of the dyes were determined from cyclic voltammetry measurements and evaluated concerning their potential use as sensitizers in p‐type dye‐sensitized solar cells (p‐DSCs). Quantum‐chemical density functional theory calculations gave further insight into the frontier orbital distributions, which are relevant for the electronic processes in p‐DSCs. In p‐DSCs using an iodide/triiodide‐based electrolyte, the polycyclic 9,10‐dicyano‐acenaphtho[1,2‐b]quinoxaline (DCANQ) acceptor‐containing dye gave the highest power conversion efficiency of 0.08 %, which is comparable to that obtained with the perylenemonoimide (PMI)‐containing dye. Interestingly, devices containing the DCANQ‐based dye achieve a higher V_OC of 163 mV compared to 158 mV for the PMI‐containing dye. The result was further confirmed by impedance spectroscopic analysis showing higher recombination resistance and thus a lower recombination rate for devices containing the DCANQ dye than for PMI dye‐based devices. However, the use of the strong electron‐accepting tricyanofurane (TCF) group played a negative role in the device performance, yielding an efficiency of only 0.01 % due to a low‐lying LUMO energy level, thus resulting in an insufficient driving force for efficient dye regeneration. The results demonstrate that a careful molecular design with a proper choice of the acceptor unit is essential for development of sensitizers for p‐DSCs.     

Magnetic properties and dye adsorption capacities of silica–hematite nanocomposites with well-defined structures prepared in surfactant solutions

Silica–hematite (α-Fe₂O₃) nanocomposites were synthesized by addition of aqueous solution containing ferrous ions (Fe²⁺), cetyltrimethylammonium bromide (CTAB) as a surfactant and tert-butanol (t-butanol) as a cosurfactant into colloidal silica solution. At alkaline atmosphere, silica surface with negative charges electrostatically attracts positively-charged iron hydroxide nuclei or particles which are stabilized by cationic CTAB molecules, and then silica–iron compound composites could be formed. Finally, the silica–hematite composite particles were obtained after calcination at 800 °C for 4 h. Through these processes, two types of composites having “core–shell type” or “decorated type” could be achieved. Morphology, BET surface area, crystallinity and magnetic properties of samples were analyzed by using TEM, BET, XRD and VSM, respectively. The “decorated type” composites had larger BET surface area and better magnetization. Also, to estimate the application in water treatment, adsorption properties of composites were studied through methylene blue (MB) adsorption which was characterized by UV–vis spectroscopy, involving collection of composites with neodymium magnet.