Ti/RuO2-CoO电极制备及其氨氮降解性能

采用热氧化法制备Ti/RuO_2-CoO电极,通过SEM和XRD对电极涂层的表面形貌和晶体结构进行表征;并利用最佳条件制备的电极开展电化学氧化氨氮模拟废水研究。实验研究了电流密度、初始pH值、Cl~-浓度和NH_3-N初始浓度对NH_3-N降解效果的影响。研究结果表明:当n(Ru)/n(Co)=7∶3时Ti/RuO_2-CoO电极对NH_3-N的去除效果较好。随着电流密度的增加,NH_3-N去除率随之升高;初始pH为碱性条件时,NH_3-N去除效果较好;NH_3-N去除率随Cl~-浓度的增加呈现先增大后减小,当Cl~-浓度为3 000 mg/L时,氨氮去除率达到97.95%。当电流密度为70 mA/cm~2、Cl~-浓度为3 000 mg/L、初始pH=9时,经过180 min电解后,氨氮初始浓度从500 mg/L降低至10.25 mg/L,且电化学氧化氨氮的产物主要为氮气和硝酸盐氮。     

用铁氰化钾分光光度法测定头孢噻肟钠

建立了以铁氰化钾测定头孢噻肟钠的分光光度法。 在0.20 mol/L NaOH溶液中,头孢噻肟钠(CTX)于100 ℃水浴中降解生成的巯基化合物能将Fe(Ⅲ)(pH=3.0)还原为Fe(Ⅱ),根据Fe(Ⅱ)与K3[Fe(CN)6]反应生成可溶性普鲁士蓝(KFeⅢ[FeⅡ(CN)6])的吸光度,可以间接测定头孢噻肟钠的含量。 头孢噻肟钠在0.040~24 mg/L范围内与吸光度(A)呈线性关系,线性回归方程:A=0.05088+0.2166ρ(mg/L),相关系数R=0.9986,检出限为0.01 mg/L,相对标准偏差(RSD)为1.36%(n=11),表观摩尔吸光系数ε=2.3×105 L/(mol·cm)。 此方法可用于药物及血清中头孢噻肟钠含量的测定。     

茚三酮为显色剂分光光度法测定氨苄西林钠

采用分光光度法研究了氨苄西林钠与茚三酮间的显色反应。 确定了反应条件,建立了一种快速、简便测定氨苄西林钠的分光光度法。 实验表明,氨苄西林钠与茚三酮在pH=5.4的水溶液中,沸水浴1 h可以反应完全,产物在λmax=564 nm下,表观摩尔吸光系数为3.72×103 L/(mol·cm)。 氨苄西林钠质量浓度在10~90 mg/L范围内服从比耳定律, 相关系数为0.9981,当氨苄西林钠浓度为40 mg/L时,测定结果的相对标准偏差为1.5%(n=6),回收率在99.0%以上。     

甲基苯丙胺电化学检测条件的优化

采用电化学方法检测甲基苯丙胺,探讨了不同扫描速度、初始浓度、pH值、电极处理温度及干扰物对检测的影响,获得了甲基苯丙胺电化学检测的最佳条件.结果表明,工作电极为掺硼金刚石薄膜电极,扫描速度为50~100 m V/s,初始浓度小于100 mg/L,pH=7.0及电极处理温度为100℃时,甲基苯丙胺的检测速度最快,检测结果最好,同时干扰物对于电化学方法检测甲基苯丙胺无明显影响.     

钙蒙脱土吸附镧的影响因素及其应用

以钙基蒙脱土(Ca-MMT)为载体,研究其对镧(La)的吸附。 采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)和元素mapping分析、傅里叶红外光谱(FT-IR)、BET、X射线荧光光谱分析(XRF)对其晶型结构、表面形态、比表面积、化学结构进行表征,考察了La的初始浓度、pH值、温度对Ca-MMT吸附镧性能的影响,考察了载镧钙基蒙脱土(Ca-MMT@La)的除磷效果。 结果表明:Ca-MMT投入量为10 g/L时,Ca-MMT的平衡吸附量随镧的初始浓度增加而增大,最大吸附量为49.62 mg/g;随着pH值增大,吸附能力增强,pH=6时为最佳pH吸附镧条件,吸附量为38.36 mg/g;随温度的升高,其吸附量先下降再上升,20 ℃吸附能力最大,吸附量为41.23 mg/g。 Langmuir等温吸附方程推断其吸附属于单分子层吸附。 Ca-MMT不具有吸附磷效果,而Ca-MMT@La对磷酸根有很强的吸附能力,吸附量为7.24 mg/g,除磷率为72.41%,其除磷率随含镧量增大而增大。     

三维电极系统电化学氧化三唑酮

以三唑酮(TDF)为目标污染物,以钛基钌铱电极和不锈钢板作阳极、阴极,颗粒活性炭(GAC)为粒子电极构建三维电极系统,通过搅拌实现粒子电极呈流化状态。研究电流密度、TDF初始浓度、GAC投加量、初始pH对三维电极系统的TDF去除效率的影响。研究结果表明:增大电流密度有助于提高TDF去除效率;TDF去除率随初始pH的增大呈现逐渐增大的趋势,碱性条件有助于TDF的去除;当GAC投加量为1～4 g/L时,增大GAC投加量有助于TDF的降解;增大TDF初始浓度会导致去除率的降低。当TDF初始浓度为200μg/L、电流密度为8m A/cm2、初始pH=11、GAC投加量为4 g/L时,电化学氧化10 min时TDF去除率达到99.95%。三维电极系统的传质效率高于二维电极系统,三维电极电化学氧化系统是一种适用于降解TDF的高级氧化技术。     

钒酸铵氧化-分光光度法测定盐酸氯丙嗪

在磷酸介质中,钒酸铵与盐酸氯丙嗪反应生成红色氧化产物,其最大吸收波长为524nm;据此建立了测定盐酸氯丙嗪含量的钒酸铵氧化-分光光度法,并将其用于直接测定药物制剂中的盐酸氯丙嗪.结果表明,当盐酸氯丙嗪的浓度处于10.0～100mg/L和100～360mg/L范围内时,被测定体系的吸光度与盐酸氯丙嗪的浓度之间呈良好的线性关系;线性回归方程分别为A=-0.061 69+0.010 05c(mg/L,r=0.998 8)、A=0.494+0.004 43c(mg/L,r=0.998 8),检出限为1.96mg/L,相对标准偏差为0.29%,回收率为94.9%～102.9%.     

乙二醇中铜胶体共振光散射光谱

在乙二醇中,以聚乙烯吡咯烷酮（PVP）为分散剂,抗坏血酸（VC）为还原剂和抗氧化剂,还原CuSO4制得铜胶体溶液。 通过XRD、UV-Vis与共振光散射（RLS）光谱对铜胶体进行表征。 结果表明,铜胶体为面心立方晶体结构的0价铜,在592~602 nm呈现典型的等离子共振吸收峰,体系具有明显的RLS特征,最大散射波长在468 nm。 考察了反应条件、体系的稳定性与共存离子对乙二醇中铜胶体RLS的影响。 结果表明,适宜的反应条件为：试剂按照VC、CuSO4和PVP的加入顺序,3种物质量的比按照n(VC)/n(Cu2+)=15、n(PVP-K30)/n(Cu2+)=1.4;反应温度60 ℃;反应时间1 h,反应得到的铜胶体可稳定放置1 d。 在适宜条件下,ρ(Cu2+)在5.12~12.8 mg/L范围内与散射光强度（ΔIRLS）成正比,回归方程为ΔI=7 420.2ρ-631.8（r=0.9962）,检出限（3σ）为0.63 μg/L。 0.64 mg/L MnSO4、CdSO4和ZnSO4,1.28 mg/L KI,64 mg/L Na2CO3和Ca(OH)2,960 mg/L CH3CH2OH,640 mg/L CH3OH和320 mg/L CH3CH2CH2OH均不干扰10 mg/L Cu2+溶液的测量。 由此建立一种利用RLS光谱测定乙二醇中铜离子的简便方法。     

聚丙烯酸钠配合-超滤分离Hg(Ⅱ)、Cu(Ⅱ)和Cd(Ⅱ)

以聚丙烯酸钠为配合剂,研究了Hg(Ⅱ)、Cu(Ⅱ)和Cd(Ⅱ)混合溶液配合-超滤分离行为。考察了pH值和负载比LR对混合体系分离的影响,结果表明,pH=5适宜分离;当LR从0.01增大至2时,金属离子分离系数SHg-Cd和SHg-Cu逐渐增大,LR=2时达到最大值。在pH=5、LR=2、体积浓缩因子为15和各金属离子的初始质量浓度为30mg/L时,截留液中金属离子的质量浓度ρr,Hg、ρr,Cu和ρr,Cd分别为435.3、42.6和34.2mg/L;SHg-Cd、SHg-Cu和SCu-Cd基本不变,依次为229.3、184.3和1.2,即Hg(Ⅱ)得到选择性浓缩。浓缩液的洗涤研究结果表明,随着洗涤液体积增大,ρr,Hg基本不变,ρr,Cu和ρr,Cd分别下降至12.54和4.73mg/L。收集含Cu(Ⅱ)和Cd(Ⅱ)的各渗透液,调节LR=0.033和pH=5,浓缩16倍时,ρr,Cu从27.34mg/L升高至430.9mg/L,ρr,Cd从27.83mg/L仅升高至61.5mg/L,SCu-Cd为95.8,Cu(Ⅱ)获得选择性浓缩。     

β-环糊精强化紫外光降解2,2-双（4-羟基-3-甲基苯）丙烷

用稳态荧光光谱法研究了2,2-双(4-羟基-3-甲基苯)丙烷(双酚C)与β-环糊精形成1∶1稳定的包结物,其生成常数为4.94×103 L/mol;研究了β-环糊精存在下双酚C的紫外光(λmax=254 nm)降解行为,结果表明,β-环糊精可促进水溶液中双酚C的紫外光降解,光降解反应符合假一级反应动力学规律. 10 mg/L双酚C经60 min紫外光照射,β-环糊精可使双酚C 的紫外光降解效率从36%提高至86%,在pH值2～8范围内,pH值对双酚C的光降解没有明显的影响;当pH＞8时,双酚C的光降解反应明显加快,随着β-CD浓度的增加双酚C的光降解反应速率也逐渐增加,当β-CD的浓度超过8.0×10-5 mol/L时,双酚C的光降解反应速率不再明显增加. β-环糊精对双酚C的包结作用引起双酚C分子键能的削弱,导致双酚C光降解作用的增强.     

电化学氧化法去除苯酚研究

利用氯碱厂报废的DSA电极电解苯酚,结果显示:此电极对一定浓度的苯酚溶液有较好的去除效果.按影响电解效果各主要因素进行筛选,最佳实验条件为:电流密度30mA/cm2,pH10,支持电解质浓度10mg/L,苯酚浓度10mg/L.电解2h后,CODcr的去除率为66.7%,吸光度去除率为90%.     

STUDY ON THE TREATMENT OF INDUSTRIAL WASTEWATER CONTAINING TRIETHYLAMINE WITH POLYMERIC ADSORBENTS

The treatment of the industrial wastewater,in which the concentration of triethylamine (TEN) and CODcr was around 3450mg/L and 22400mg/L respectively,was studied by adsorption of macroporous resins,Results demonstrate that the polymeric adsorbent CHA-111 has excellent effect on the adsorption and desorption of TEN.The concentration of TEN in the effluent is less than 30mg/L,and the removal efficiency of TEN and total CODcr exceed 99% and 95% respectively.The accumulation and resource reuse of TEN can be realized in this process.     

Ru0.7Si0.3O2/Ti电极电催化氧化处理硝基苯废水

制备了Ru0.7Si0.3O2/Ti电极,并以该电极作为氧化阳极,不锈钢为阴极,电催化氧化降解废水中硝基苯。 实验结果表明,当硝基苯初始质量浓度为220 mg/L时,最佳条件为：电流密度25×10-3 A/cm2;Na2SO4作为电解质时加入量为8 g/L;溶液初始pH=2。 在此最佳条件下,硝基苯去除率大于85%,TOC去除率大于50%,表明Ru0.7Si0.3O2/Ti阳极能有效去除废水中有机污染物;对中间产物的检测结果表明,硝基苯的降解是阴阳两极协同作用的结果。     

A comparative study of the anion transfer kinetics across a water/nitrobenzene interface by means of electrochemical impedance spectroscopy and square-wave voltammetry at thin organic film-modified electrodes

The kinetics of the transfer of a series of hydrophilic monovalent anions across the water/nitrobenzene (W/NB) interface has been studied by means of thin organic film-modified electrodes in combination with electrochemical impedance spectroscopy and square-wave voltammetry. The studied ions are Cl-, Br-, I-, ClO4-, NO3-, SCN-, and CH3COO-. The electrode assembly comprises a graphite electrode (GE) covered with a thin NB film containing a neutral strongly hydrophobic redox probe (decamethylferrocene or lutetium bis(tetra-tert-butylphthalocyaninato)) and an organic supporting electrolyte. The modified electrode is immersed in an aqueous solution containing a supporting electrolyte and transferring ions, and used in a conventional three-electrode configuration. Upon oxidation of the redox probe, the overall electrochemical process proceeds as an electron-ion charge-transfer reaction coupling the electron transfer at the GE/NB interface and compensates ion transfer across the W/NB interface. The rate of the ion transfer across the W/NB interface is the limiting step in the kinetics of the overall coupled electron-ion transfer reaction. Moreover, the transferring ion that is initially present in the aqueous phase only at a concentration lower than the redox probe, controls the mass transfer regime in the overall reaction. A rate equation describing the kinetics of the ion transfer that is valid for the conditions at thin organic film-modified electrodes is derived. Kinetic data measured with two electrochemical techniques are in very good agreement.     

Novel electrochemical procedure for the determination of metamitron

In this paper, a chronopotentiometric method for the determination of herbicide metamitron (MTM) using a glassy carbon electrode (GCE) and a thin film mercury electrode (TFME) as working electrodes is presented. MTM provided a well-defined reductive peak in the Britton–Robinson buffer on both working electrodes. Instrumental and chemical factors such as pH of the buffer, initial potential and reduction current influencing MTM chronopotentiometric response were optimised with the Box–Behnken experimental design. Under the optimal combination of factors, the analytical signal was linear in the MTM concentration range of 0.8–30 mg/L, with a detection limit of 68.53 µg/L using a TFME, and in the concentration range of 1–30 mg/L, with a detection limit of 92.91 µg/L using a GCE. The precision of the method was estimated as a function of repeatability and reproducibility, with the value of relative standard deviation lower than 2.6%. The applicability of the method was verified by direct analysis of MTM in spiked water samples and commercial pesticide formulations. The obtained results were in good agreement with those obtained using liquid chromatography/tandem mass spectrometry (LC-MS/MS) method, or with those labelled by the manufacturer. By using chronopotentiometry, neither extraction nor preconcentration procedures are necessary, thus making this method simple, cost-effective and more feasible for analytical routine analysis.     

碳纳米管的快速功能化及电催化

将耐尔兰(Nile Blue, NB)分子修饰到碳纳米管(CNT)表面形成NB-CNT纳米复合体, 谱学结果表明, NB不仅能快速、高效地修饰到CNT表面, 而且还能有效地改善CNT在水溶液中的分散性能. 将NB-CNT修饰到玻碳(GC)电极表面制备了NB-CNT/GC电极, 循环伏安结果显示, 其伏安曲线上不仅表现出一对良好的、几乎对称的NB单体的氧化还原峰, 式量电位E⁰'几乎不随扫速而变化[其平均值为(－0.422±0.002) V (vs. SCE, 0.1 mol/L PBS, pH 7.0)]; 而且还显示出NB聚合体分子的氧化还原峰, E⁰'为－0.191 V (100 mV/s时). 进一步的实验结果表明, NB和CNT对NADH(即还原型β-烟酰胺腺嘌呤二核苷酸, 又称还原型辅酶I)的电化学氧化具有协同催化作用, 能使其氧化过电位降低多于560 mV; NB-CNT/GC电极还能较好地响应脱氢酶催化底物氧化过程中体系内NADH浓度的变化. 本文对碳纳米管功能化方法具有简单快速、电极制作容易以及催化效率高等优点, NB-CNT/GC电极有望在制作脱氢酶传感器方面得到应用.     

Voltammetric Reduction of a 4‐Nitroimidazole Derivative on a Multiwalled Carbon Nanotubes Modified Glassy Carbon Electrode

We report the electrochemical behavior of a 4‐nitroimidazole derivative, 1‐methyl‐4‐nitro‐2‐hydroxymethylimidazole (4‐NImMeOH), on glassy carbon electrode (GCE) modified with multiwalled carbon nanotubes (MWCNT). As dispersing agents, dimethylformamide (DMF) and water were used. The electrochemical response of the resulting electrodes was evaluated using linear sweep, cyclic and square‐wave voltammetry (LSV, CV and SWV). Several parameters such as medium pH, nature and concentration of the CNTs dispersion and accumulation time were tested. The optimal conditions determined for obtain better response were: pH 2, dispersion concentration=4 mg/mL of CNT in water, accumulation time=7 min. The MWCNT‐modified GCE exhibited attractive electrochemical properties producing enhanced currents with a significant reduction in the overpotential and good signal‐to‐noise characteristics, in comparison with the bare GCE. The modified electrode is highly repeatable for consecutive measurements, reaching a variation coefficient of 2.9% for ten consecutive runs.     

毛细管电泳-安培检测法测定女贞子中齐墩果酸的含量

女贞子又名冬青子,性凉,味甘、微苦,归肝、肾经,具有滋补肝肾、明目乌发的功能.女贞子主要有效成份为齐墩果酸Oleanolic Acid(OA)[1],其化学结构式如图1所示.OA是天然产物化学成分,毒性很低,具有多种生物活性如抗病毒、消炎、增强免疫和抑制免疫、抑制血小板凝集、降血脂、降糖、保肝、护肾、抗艾滋病毒等[2],故测定其含量可为药品的含量控制提供科学依据.     

双电极法现场快速检测地下水和湖水中碳酸氢根和碳酸根

地下水和湖水中碳酸氢根( HCO-3)和碳酸根( CO2-3)含量是地球化学碳行为和碳循环的重要表征,但两种离子的浓度易受环境影响而改变,因此,地下水和湖水中HCO-3和CO2-3真实含量的测定一直是个难题。实验利用CO2的水解平衡,通过pH电极和二氧化碳电极联用,建立了HCO-3和CO2-3现场快速测定的新方法,解决了地下水和湖水中HCO-3和CO2-3真实含量的测定难题。研究结果表明,在pH=4.8±0.1的底液中, HCO-3和CO2-3的线性范围分别为0.027~570 mg/L和1.25×10-8~39.7 mg/L。共存的金属离子、强酸阴离子(K+、Na+、Mg2+、Cl-、SO2-4,100 mg/L)、弱酸阴离子和弱酸(HSO-3、NO-2、HOAc,50 mg/L)对测定干扰小于5%。实际水样加标实验回收率在95.2%~99.2%之间,相对标准偏差为2.6%~3.7%。与酸碱滴定法进行对比,本方法的准确性良好。但方法受温度影响,因此标准溶液与样品应在同一温度下测量。总体而言,双电极法灵敏、快速、经济且电极携带方便、操作简单、对环境要求不高,十分适合现场和室内一般自然水体的快速检测。本方法已成功应用于青海省地下水和青海湖湖水中HCO-3和CO2-3的现场测定。实验表明,海东地区地下水样品pH在6.4~7.4之间,HCO-3含量为234~4096 mg/L,CO2-3含量为0.16~1.89 mg/L;青海湖湖水样品pH≈8.7,HCO-3含量范围在1.36~1.86 g/L,CO2-3含量在32.3~43.9 mg/L,与文献结果吻合。