Preparation and characterization of monodisperse solvent-free silica nanofluids

A series of solvent-free ionic silica (SiO₂) nanofluids of 12.3–17.3 nm in diameter were synthesized by surface functionalizing nanoscale SiO₂ with a charged corona and ionically tethering with oligomeric chains as canopy. The structure and properties of the nanofluids were systematically characterized by Fourier transform infrared (FTIR), differential scanning calorimeter (DSC), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and rheology tests. The resultant nanofluids with low-molecular-weight oligomeric as canopy are homogeneous, stable yellow-like fluids with no evidence of phase separation at room temperature, while other nanofluids containing high-molecular-weight as canopy behave like a soft glassy, and they exhibit fluidity with still high modulus and viscosity above 60°C. For deeper understanding of the nature of SiO₂ nanofluids, the rheological behavior, thermal stability, as well as morphology of SiO₂ nanofluids were investigated in details. The flow properties of nanofluids could be easily regulated from soft glassy to free flowing liquids by varying the molecule weight of canopy. Most importantly, the thermal stability, rheological behavior, as well as morphology can be also regulated through varying molecule weight and thickness of canopy, which will guide our future work on synthesis of nanofluids with controllable physical properties.     

Preparation and characterization of silica supported Au-Pd model catalysts

Au-Pd bimetallic model catalysts were synthesized as alloy clusters on SiO2 ultrathin films under ultrahigh vacuum (UHV) conditions. The surface composition and morphology were characterized with low energy ion scattering spectroscopy (LEIS), infrared reflection absorption spectroscopy (IRAS), and temperature programmed desorption (TPD). Relative to the bulk, the surface of the clusters is enriched in Au. With CO as a probe, IRAS and TPD were used to identify isolated Pd sites at the surface of the supported Au-Pd clusters. Ethylene adsorption and dehydrogenation show a clear structure-reactivity correlation with respect to the structure/composition of these Au-Pd model catalysts.     

Preparation and characterization of mesoporous silica thin films from polyethoxysiloxanes

Tetraethoxysilane (TEOS) and polyethoxysiloxanes (PEOSs; prepared by the acid‐catalyzed hydrolytic polycondensation of TEOS) were subjected to the sol–gel process in the presence of cetyltrimethylammonium bromide (CTAB), respectively. The PEOSs with M_w 700–26,000, as prepared by sol–gel coating of TEOS and PEOS under various conditions, were used. Uniform and crack‐free thin films of thickness 276–613 nm were prepared by spin‐coating of a PEOS solution containing CTAB. When the coating films were sintered at 400 °C, the combustion of ethoxy groups and CTAB took place to provide porous silica thin films. The structure of the thin films was found to be dependent on the molecular weight of PEOS and the molar ratio of CTAB/Si: lamellar or hexagonal phase was observed for M_w less than 15,000 and for CTAB/Si molar ratios greater than 0.10. Honeycomb structures were observed for M_w less than 5000 and for CTAB/Si molar ratios of 0.15. The honeycomb structure was also observed by atomic force microscopy and transmission electron microscope. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2542–2550, 2006     

Preparation and characterization of novel polyimide‐silica hybrids

Polyimide‐silica (PI‐SiO₂) hybrids were prepared from a novel polyimide (PI), derived from pyromellitic dianhydride (PMDA), 1,6‐bis(4‐aminophenoxy)hexane (synthesized) and 4,4′‐oxydianiline. SiO₂ networks (5–30 wt%) were generated through sol–gel process using either tetraethylorthosilicate (TEOS) or a mixture of 3‐aminopropyltriethoxysilane‐PMDA‐based coupling oligomers (APA) and TEOS. Thin, free standing hybrid films were obtained from the respective mixtures by casting and curing processes. The hybrid films were characterized using Fourier transform infrared, ²⁹Si nuclear magnetic resonance (NMR), field emission scanning electron microscopy (FE‐SEM), energy dispersive X‐ray spectrometry and atomic force microscopy (AFM) techniques. ²⁹Si NMR results provide information about formation of organically modified silicate structures that were further substantiated by FE‐SEM and AFM micrographs. Contact angle measurements and thermogravimetric thermograms reveal that the addition of APA profoundly influences surface energy, interfacial tension, thermal stability and the residual char yield of modified hybrids in comparison to those obtained by mixing only TEOS. It was found that reduced particle size, efficient dispersion and improved interphase interactions were responsible for the eventual property enhancement. Copyright © 2012 John Wiley & Sons, Ltd.     

Iron-modified mesoporous SBA-15 silica: Preparation and characterization studies

Fe-SBA-15 materials with different Si/Fe ratios (Si/Fe = 100, 60, 15) have been synthesized by hydrothermal method and characterized by several spectroscopic techniques. Electron spin resonance and Mössbauer spectroscopy, along with electron microscopy and X-ray diffraction, allowed differentiation of several iron species. These species correspond to hematite particles, very small “isolated” or oligomeric Fe^III species possibly incorporated in the mesoporous silica wall, and Fe^III oxide clusters either isolated or agglomerated, forming “rafts” at the surface of the silica and exhibiting ferromagnetic ordering. Because of their agglomeration, these clusters appear with a two-peak size distribution, with one peak corresponding to the isolated clusters formed in the mesopores and still embedded in them and the other corresponding to the agglomerates spread on the surface of the mesoporous silica particles.     

Preparation and characterization of mixed-mode monolithic silica column for capillary electrochromatography

A silica-based monolithic stationary phase with mixed-mode of reversed phase (RP) and weak anion-exchange (WAX) for capillary electrochromatography (CEC) has been prepared. The mixed-mode monolithic silica column was prepared using the sol–gel technique and followed by a post-modification with hexadecyltrimethoxysilane (HDTMS) and aminopropyltrimethoxysilane (APTMS). The amino groups on the surface of the stationary phase were used to generate a substantial anodic EOF as well as to provide electrostatic interaction sites for charged compounds at low pH. A cathodic EOF was observed at pH above 7.3 due to the full ionization of residual silanol groups and the suppression in the ionization of amino groups. A variety of analytes were used to evaluate the electrochromatographic characterization and column performance. The monolithic stationary phase exhibited RP chromatographic behavior toward neutral solutes. The model anionic solutes were separated by the mixed-mode mechanism, which comprised RP interaction, WAX, and electrophoresis. Symmetrical peaks can be obtained for basic solutes because positively charged amino groups can effectively minimize the adsorption of positively charged analytes to the stationary phase.     

Preparation and characterization of molecularly imprinted silica monolith for screening sulfamethazine

In this work, a novel approach of preparing molecularly imprinted film‐derivatized silica monolith materials was developed by a two‐step procedure. The silica monolithic support was first prepared by the sol–gel method with tetramethoxysilane as the precursor. Subsequently, vinyl groups were introduced onto the surface of silica monolith by immobilization of γ‐methacryloxypropyltrimethoxysilane. The prepolymerization mixtures, consisting of methacrylic acid as a functional monomer, ethylene dimethacrylate as a crosslinker, sulfamethazine as a template molecule and an ionic liquid as porogen, were injected into the silica monolith immobilized vinyl groups to form the molecularly imprinted films on the surface of the vinyl functionalized silica monolith. The monolithic materials were characterized by SEM, Fourier transform IR and solid‐state reflection UV spectra. The resulted imprinted materials were evaluated under CEC and HPLC mode. The results indicated that there were enough recognition sites on the surface of the imprinted film‐derivatized monolithic materials for selectively recognizing sulfamethazine from the sulfonamide mixture. Ionic liquids, which was utilized as the porogens, could improve the flow‐through property and the imprinting effect of the molecularly imprinted film‐functionalized silica monolithic materials.     

Preparation and characterization of polyimide/pure silica zeolite hybrid films

In this study, amino derivative of pure silica zeolite nanocrystal (A‐PSZN) was dispersed into polyimide (PI) matrix to prepare PI/A‐PSZN hybrid films, and their thermal and mechanical properties, as well as hydrophobicity, were characterized scientifically. The test results show that PI/A‐PSZN hybrid films possess higher glass transition temperature, higher thermal stability and lower in‐plane coefficient of thermal expansion than pristine PI. The mechanical property data suggest that the incorporation of A‐PSZN results in an increase in Young's modulus and tensile strength of the hybrid films, but as its content exceeds the critical value (maybe 5 wt%), its enhancement effect on the hybrid's strength and toughness gets weaker. Furthermore, liquid dripping imaging analysis results indicate that the film's hydrophobicity is clearly improved by the introduction of A‐PSZN. As compared with PSZN, A‐PSZN exhibits better effect on enhancing the overall performance of pristine PI films. A comparison with other studies suggests that PI/A‐PSZN is a hybrid film with superior comprehensive properties. Copyright © 2013 John Wiley & Sons, Ltd.     

Preparation and characterization of polypropylene/mesoporous silica nanocomposites with confined polypropylene

Polypropylene (PP)/Ti-MCM-41 nanocomposites were prepared by isospecific propylene polymerization with Ti-MCM-41/Al(i-C₄H₉)₃ catalyst. The cross polarization/magic angle spinning (CP/MAS) ¹³C NMR spectrum of the composite was similar to that of the conventional isotactic PP, and the decrease in the pore volume of Ti-MCM-41 in the nanocomposites, as measured by N₂ adsorption, was consistent with the value calculated from the weight loss in the thermogravimetric analysis (TGA) curve; both these facts attest to propylene polymerization within the mesopores of Ti-MCM-41. Alkali treatment followed by extraction with o-dichlorobenzene allows us to extract the confined PP out of the Ti-MCM-41 mesopores. Although the PP/Ti-MCM-41 nanocomposites do not exhibit a crystalline melting point, the same PP when extracted from the mesopores showed a clear melting point at 154.7 °C; this indicates that the crystallization of PP confined in mesopores is strongly hindered. For the PP polymerized within the confinement, the molecular weight (M_w) and molecular weight distribution (M_w/M_n) were 84,000 and 4.3, respectively; these values were considerably smaller than those of the PP polymerized concurrently outside the Ti-MCM-41 mesopores (M_w = 200,000–450,000, M_w/M_n = 40–75). Therefore, the confinement also has a marked effect on the molecular weight of the PP. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3324–3332, 2003     

Preparation, characterization and biodegradation of biopolymer nanocomposites based on fumed silica

PLA and PCL based nanocomposites prepared by adding three different types of fumed silica were obtained by melt blending. Materials were characterized by means of Scanning Electron Microscopy (SEM), Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA) and Dynamic–Mechanical Thermal Analysis (DMTA).A good distribution of the fumed silica into both polymer matrices was observed. The highest thermo-mechanical improvements were reached by addition of the fumed silica with higher surface area. PLA and its nanocomposites were degraded in compost at 58 °C; at this temperature all samples presented a significant level of polymer degradation, but a certain protection action of silica towards PLA degradation was observed, whereas the addition of fumed silica did not show considerable influence on the degradation trend of PCL. These dissimilarities were attributed to the different degradation mechanism of the two polymers.     

Preparation and characterization of silica aerogels from diatomite via ambient pressure drying

The silica aerogels were successfully fabricated under ambient pressure from diatomite. The influence of different dilution ratios of diatomite filtrate on physical properties of aerogels were studied. The microstructure, surface functional groups, thermal stability, morphology and mechanical properties of silica aerogels based on diatomite were investigated by BET adsorption, FT-IR, DTA-TG, FESEM, TEM, and nanoindentation methods. The results indicate that the filtrate diluted with distilled water in a proportion of 1: 2 could give silica aerogels in the largest size with highest transparency. The obtained aerogels with density of 0.122–0.203 g/m³ and specific surface area of 655.5–790.7 m²/g are crack free amorphous solids and exhibited a sponge-like structure. Moreover, the peak pore size resided at 9 nm. The initial aerogels were hydrophobic, when being heat-treated around 400°C, the aerogels were transformed into hydrophilic ones. The obtained aerogel has good mechanical properties.     

Preparation and characterization of NiFe bimetallic micro-particles and its composite with silica shell

Magnetic NiFe particles were synthesized through hydrothermal method using hydrazine as reductant. Composite particles with core-shell structure were further achieved by depositing silicon dioxide generated via carbonation decomposition of sodium silicate solution on the surface of magnetic cores. Characterized by XRD, the Ni₉Fe particles are of fcc-type structure, and the structure of magnetic cores in composite particles was maintained despite being covered by SiO₂ shell. The existence of SiO₂ shells in the composite particles were demonstrated by SEM, EDS and IR. The results from TG and VSM indicated that the shell structure affected the physiochemical properties. The composite particles exhibited remarkable resistance to oxidation in comparison with Ni₉Fe particles due to being protected by SiO₂ shell. Meanwhile, both of them are soft magnetic materials, but Ms, Mr and Hc in Ni₉[email protected]₂ particle decreased compared with magnetic NiFe particles. The formation mechanisms of Ni₉Fe micro-particles and composite Ni₉Fe particles were discussed.     

Preparation and characterization of monodisperse porous silica microspheres with controllable morphology and structure

A novel method for the preparation of monodisperse porous silica microspheres with controllable morphology and structure is reported. The starting porous polymer microspheres were first functionalized with ethylenediamine (EDA) to generate amino groups. Subsequently, silica nanoparticles were deposited in the porous polymer microsphere to form polymer/silica hybrid microspheres via a modified sol‐gel process in the presence of tetra‐n‐butylammonium bromide (TBAB) or tetramethyl ammonium hydroxide (TMAH). Upon calcination of the polymer/silica hybrid microspheres, the porous silica microspheres were obtained. The morphology, inner structure, and properties of the porous silica microspheres were studied by field emission scanning electron microscope, Fourier transform infrared spectroscopy, thermogravimetric analysis, and mercury intrusion method. The results show that the presence of TBAB or TMAH in the process not only prevents the agglomeration of the hybrid microspheres, but also governs the controllable morphology from a porous inner structure to a hollow‐cage structure. The obtained porous silica microspheres exhibit no shrinkage from the polymer microspheres with a yield of around 98%. These porous silica microspheres have potential applications in the fields of chromatography, catalyst, and biology. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation and characterization of carbosilane dendrimer-bonded silica gel and its use in LC

Divergently synthesized carbosilane dendrimers generations 1(G1) and 2 (G2) with allyl end groups were bonded onto silica gel. Reactions between the dendrimers and acid-processed silica gel took place, with toluene reflux and organic base as catalyst. Chemically bonded silica gel was characterized by transmission electron microscopy (TEM), infrared (IR), and other methods. The chemically modified silica gels were packed into high-pressure liquid chromatography (HPLC) column and their separation characters were evaluated. G2-bonded silica gel was effective in separating homologous compounds of alcohol, alkyl-substituted benzene, N-substituted benzene, metacrylic acid ester and phthalate. __________ Translated from Journal of Shandong University, 2005, 40(6) (in Chinese)     

Preparation, characterization and application of magnetic silica nanoparticle functionalized multi-walled carbon nanotubes

Magnetic silica nanoparticle functionalized multi-walled carbon nanotubes (MS-MWNTs) were prepared, characterized and used for the convenient, rapid and efficient separation of trace aromatic compounds.     

聚N-异丙基丙烯酰胺硅胶键合固定相的制备与评价

以3-巯丙基三甲氧基硅烷为偶联剂,将聚N-异丙基丙烯酰胺(PNIPAM)键合到硅胶上,制得了键合固定相（SI-PNIPAM）填料,并用元素分析、红外光谱等对其进行了表征。以甲醇-水为二元流动相,用多环芳烃、碱性物质对该固定相进行了色谱评价,并考察了该固定相的适用pH范围及水解稳定性。结果表明:该固定相具有较好的色谱性能与温敏特性,并且在pH 2.5～7.5时稳定性良好。     

Preparation and characterization of polymer/silica nanocomposites via double in situ miniemulsion polymerization

Polymer/SiO₂ nanocomposite microspheres were prepared by double in situ miniemulsion polymerization in the presence of methyl methacrylate, butyl acrylate, γ‐methacryloxy(propyl) trimethoxysilane, and tetraethoxysilane (TEOS). By taking full advantage of phase separation between the growing polymer particles and TEOS, inorganic/polymer microspheres were fabricated successfully in a one‐step process with the formation of SiO₂ particles and the polymerization of organic monomers taking place simultaneously. The morphology of nanocomposite microspheres and the microstructure, mechanical properties, thermal properties, and optical properties of the nanocomposite films were characterized and discussed. The results showed that hybrid microspheres had a raspberry‐like structure with silica nanoparticles on the shells of polymer. The silica particles of about 20 nm were highly dispersed within the nanocomposite films without aggregations. The transmittance of nanocomposite film was comparable to that of the copolymer film at around 70–80% from 400 to 800 nm. The mechanical properties and the fire‐retardant behavior of the polymer matrix were improved by the incorporation of silica nanoparticles. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3128–3134, 2010     

Preparation and characterization of ultrathin dual-layer ionic liquid lubrication film assembled on silica surfaces

A novel ultrathin dual-layer film, which contained both bonded and mobile phases in ionic liquids (ILs) layer, was fabricated successfully on a silicon substrate modified by a self-assembled monolayer (SAM). The formation and surface properties of the films were analyzed using ellipsometer, water contact angle meter, attenuated total reflectance Fourier transform infrared spectroscopy, multi-functional X-ray photoelectron spectroscopy, and atomic force microscope. Meanwhile, the adhesive and nanotribological behaviors of the films were evaluated by a homemade colloidal probe. A ball-on-plate tribometer was used to evaluate the microtribological performances of the films. Compared with the single-layer ILs film deposited directly on the silicon surface, the as-prepared dual-layer film shows the improved tribological properties, which is attributed to the special chemical structure and outstanding physical properties of the dual-layer film, i.e., the strong adhesion between bonded phase of ILs and silicon substrate via the chemical bonding with SAM, the interlinked hydrogen bonds among the molecules, and two-phase structure composed of steady bonded phase with load-carrying capacity and flowable mobile phase with self-replenishment property.