Electro-reduction of cuprous chloride powder to copper nanoparticles in an ionic liquid

Cyclic voltammetry of the CuCl powder in a cavity microelectrode revealed direct electro-reduction in solid state in 1-butyl-3-methylimidazolium hexafluorophosphate. Potentiostatic electrolysis of the salt powder (attached to a current collector) in the ionic liquid produced Cu nanoparticles as confirmed by X-ray diffraction, energy dispersive X-ray analysis, scanning and transmission electron microscopy. The particle size decreased down to 10 nm when the electrode potential was shifted from −0.9 V to −1.8 V (versus Ag/Ag⁺). The electro-reduction and the nanoparticle formation mechanisms were investigated in the ionic liquid and also in aqueous 0.1 mol L⁻¹ KClO₄ in which larger Cu particles were obtained.     

Graphene oxide doped polyaniline for supercapacitors

A novel high-performance electrode material based on fibrillar polyaniline (PANI) doped with graphene oxide sheets was synthesized via in situ polymerization of monomer in the presence of graphene oxide, with a high conductivity of 10 S cm^?1 at 22 °C for the obtained nanocomposite with a mass ratio of aniline/graphite oxide, 100:1. Its high specific capacitance of 531 F/g was obtained in the potential range from 0 to 0.45 V at 200 mA/g by charge–discharge analysis compared to 216 F/g of individual PANI. The doping and the ratio of graphene oxide have a pronounced effect on the electrochemical capacitance performance of the nanocomposites.     

Influence of surface oxygen groups on V(II) oxidation reaction kinetics

The role of surface oxygen groups on the kinetics of the V(II) oxidation reaction was studied on modified glassy carbon (GC) electrodes by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The reaction was found to be sensitive to the presence of oxygen groups on the electrode surface. Higher O/C ratios determined by X-ray photoelectron spectroscopy (XPS) corresponded to higher reactivities and lower charge transfer resistances measured in a 1 M V(II) electrolyte. The stability of an oxidised GC surface was also investigated in a 1 M V(II) electrolyte by potential holding and cycling experiments. It was found that after holding and cycling to successively more negative potentials up to − 0.8 V/RHE, the electrode surface lost its initial reactivity.     

Electrochemical behavior of CO2 reduction on palladium nanoparticles: Dependence of adsorbed CO on electrode potential

The electrochemical reduction of CO₂ is strongly influenced by both the applied potential and the surface adsorption status of the catalyst. In this work a gas diffusion electrode (GDE) coated with Pd nanoparticles/carbon black (Pd/XC72) was used to study the electrochemical reduction of CO₂. Cyclic voltammetric (CV) analysis of Pd/XC72 between 1.5 V and − 0.6 V (vs. RHE) shows the formation of intermediates and the blocking of hydrogen absorption on the Pd nanoparticles (NPs) under a CO₂ atmosphere. The relationships between the Faradaic efficiency/current density and the applied potential reveal that the onset potential of CO formation is around − 0.4 V. Moreover, the presence of adsorbed CO was confirmed through CV analysis of Pd/XC72 under CO₂ and CO/He atmospheres. This demonstrates that H atoms and CO intermediates co-adsorb on the surface of the Pd NPs at an applied potential of around − 0.4 V. When the applied potential is more negative than − 0.6 V, adsorption of CO intermediates on the surface of the Pd NPs becomes dominant.     

Investigation of Iron-based Nanoparticles Action by Solid-phase Voltammetry

The electrochemical conversion of Fe₂O₃ nano-particles from the surface of carbon paste electrode was investigated by solid-phase voltammetry. Cyclic voltammetric curves of Fe₂O₃ nanoparticles transformations were recorded in direct current (first derivative) mode with a potential change at the speed of 80-90 mV/s in the potential range from -1.2 to +1.0 V. The dependence of the anodic peak of Fe₂O₃ nanoparticles on exposure time in a background electrolyte was researched and the method for identifying and quantification of solid-phase nanoparticles of Fe₂O₃ was developed. The results of determination were tested by a standard addition method.     

Electrochemical properties of ordered mesoporous carbon and its electroanalytical application for selective determination of dopamine

The electrochemical properties of one novel carbon material, ordered mesoporous carbons (OMC), synthesized by templating SBA-15 mesoporous silica materials and the electrocatalytic behaviors of OMC modified electrode towards the oxidation of dopamine (DA) and ascorbic acid (AA) were studied. Cyclic voltammetry was used to evaluate the electrochemical behaviors of OMC in 5 mM K₃Fe(CN)₆/0.1 M KCl solution. OMC showed a faster electron transfer rate, as compared with glass carbon (GC) electrode. The higher electron transfer kinetics can be attributed to the existence of a large amount of edge plane defect sites in the OMC materials, which was verified by Raman spectroscopy. The cyclic voltammetric studies also showed the presence of oxygen-containing functional groups on the surface of OMC. Furthermore, the OMC modified electrode showed high electrocatalytic activities toward the oxidation of DA and AA, and resolved their voltammetric responses into two well-defined peaks with peak separation of ca. 0.210 V. The OMC modified electrode could be effectively used for the selective electrochemical determination of DA in the presence of AA.     

Electrochemical stripping analysis of cadmium on tantalum electrode

A tantalum electrode is reported as an alternative electrode for electrochemical stripping analysis for the first time. Several key operational parameters that influenced the electroanalytical signals were optimized, such as pH of the electrolyte, deposition potential and deposition time. The tantalum electrode yields well-defined and sharp stripping signals for trace cadmium analysis when combined with differential pulse anodic stripping voltammetry. Under the optimized condition the electrode shows good linear behavior in the examined concentration in the range of 20–200 μg L^?1 for cadmium, with a detection limit (3σ) of 0.57 μg L^?1 followed a 5-min deposition step under ? 1.3 V. It also shows good reproducibility with a relative standard deviation of 2.56% for ten consecutive measurements. The sensor was also employed for real sample determination and exhibited excellent performance compared with the result of inductively coupled plasma-mass spectrometry.     

Influence of the surface termination on the electrochemical properties of boron-doped diamond (BDD) interfaces

The paper reports on the electrochemical study of heavily boron-doped diamond (BDD) in aqueous media. Cyclic voltammetry and Mott-Schottky analysis were used to evaluate the influence of the surface termination on the electrochemical properties of BDD electrodes. The behavior of aminated BDD (NH₂–BDD) interfaces, prepared from hydrogen-terminated BDD using NH₃ plasma and from photochemically oxidized BDD (HO–BDD) using 3-aminopropyltrimethoxysilane (APTMES), are investigated and compared to those of H–BDD and HO–BDD. While H–BDD and HO–BDD electrodes show classical semiconductor behavior, amine-terminated BDD interfaces exhibit metallic behavior at pH < 10 and a semiconductor behavior at more basic pH.     

Preparation of boron-doped diamond nanowires and their application for sensitive electrochemical detection of tryptophan

The paper reports on the fabrication and electrochemical investigation of boron-doped diamond nanowires (BDD NWs) electrodes. The nanowires were obtained directly from highly doped polycrystalline diamond substrates using reactive ion etching (RIE) with oxygen plasma. The technique does not require any complicated processing steps such as mask deposition or template removal. The influence of the surface state on the electrochemical characteristics is discussed. The interface with the most favourable electrochemical response is investigated for the detection of tryptophan using differential pulse voltammetry. A detection limit of 5 × 10^?7 M was obtained on oxidized BDD NWs, as compared to 1 × 10^?5 M recorded on planar oxidized boron-doped diamond interfaces.     

Electrochemical fabrication of novel fluorescent polymeric film: Poly(pyrrole–pyrene)

We describe herein the electrochemical characterization and polymerization of 4-pyren-1-yl-butyric acid 11-pyrrol-1-yl-decyl ester (pyrrole–pyrene) in CH₃CN. The electrochemical oxidation of the pyrrole group at 0.77 V vs Ag/Ag + 10 mM in CH₃CN led to the first example of a fluorescent polypyrrole film. The mechanism of deposition on platinum electrode was studied by voltammetry and chronoamperometry. The optical properties of the polymeric films electrogenerated on ITO electrodes were examined by UV–visible spectroscopy and fluorescence microscopy indicating an increase in fluorescence properties by increased polymer thickness. The electrochemical oxidation of pyrenyl group linked to the polypyrrole backbone was carried out at 1.2 V. This additional polymerization was demonstrated by UV–visible spectroscopy and induced the loss of the fluorescence properties of the resulting polymeric film.     

Electrolysis of solid MoS2 in molten CaCl2 for Mo extraction without CO2 emission

Sintered (300 °C) porous pellets of MoS₂ were electrolysed to elemental S and Mo in molten CaCl₂ (800–900 °C) under argon at 1.0–3.0 V for 1–20 h. On a graphite anode, the product was primarily S (but traces of CS₂ could not yet be excluded by this work) and evaporated from the molten salt, allowing the electrolysis to continue. It then condensed to solid at the lower temperature regions of the system. The anode remained intact after repeated uses. The MoS₂ pellet was highly conducting at high temperatures and could be fast electro-reduced to fine Mo powders (0.1–1.0 μm) in which the S content could be below 1000 ppm. No reduction occurred at voltages below 0.5 V. Partial reduction was seen at 0.5–0.7 V, and converted MoS₂ to a mixture of MoS₂ and Mo₃S₄, or Mo₃S₄ and Mo with the Mo content increasing with the voltage. Cyclic voltammetry of the MoS₂ powder in a Mo-cavity electrode, together with the electrolysis results, revealed the reduction mechanism to include two steps: MoS₂ to Mo₃S₄ at −0.28 V (potential vs. Ag/AgCl), and then to Mo at −0.43 V.     

Adsorption of 2,2′-bipyridine at an Au(111)|ionic liquid electrified interface

The adsorption of added 2,2′-bipyridine (2,2′-BP) from 1-ethyl-2,3-dimethyl imidazolium bis(trifluoromethanesulfonyl)imide (EMMImNTf₂) at an Au(111) electrode has been investigated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Addition of 2,2′-BP to the ionic liquid clearly modifies the interfacial region as a result of the competition between 2,2′-BP and EMMImNTf₂ to occupy the electrode surface. Within the region of ideal polarizability, the 2,2′-BP adlayer undergoes structural changes, shown by the presence of peaks in the CV curves. Between −0.2 V and + 0.9 V, the capacitance–potential curves obtained from EIS data present a capacity maximum depending strongly on the ac frequency, which is typical pseudo-capacitive behavior indicative of a reorganization of the interfacial layer. At more positive potentials a true capacity value close to 10 μF.cm^− 2 and invariant with the potential suggests that the 2,2′-BP molecules adopt a perpendicular orientation with the nitrogen atoms facing the electrode surface, similar to their adsorption on gold from aqueous solutions.     

Amperometric sensing of dopamine using a single-walled carbon nanotube covalently attached to a conical glass micropore electrode

A single-walled carbon nanotube (SWNT) is covalently attached to the interior surface of a conical glass micropore electrode (GME) to create a novel amperometric dopamine sensor (SWNT/NH-GME). The SWNT/NH-GME combines the advantages of excellent transport properties of the cone-shaped micropore with the characteristics of a SWNT, exhibiting a dramatic electrocatalytic effect on the oxidation of dopamine (DA). Cyclic voltammetry and amperometric methods were employed to study the electrochemical behavior of the SWNT/NH-GME. The results showed that the SWNT/NH-GME sensor exhibited an excellent immunity from ascorbic acid interference and was able to measure DA concentrations with a detection limit of 4.2 × 10^?7 mol/L (S/N = 3).     

In situ AFM studies of SEI formation at a Sn electrode

Early stages of the solid electrolyte interphase (SEI) formation at a tin foil electrode in an ethylene carbonate (EC) based electrolyte were investigated by in situ AFM and cyclic voltammetry (CV) at potentials >0.7 V, i.e., above the potential of Sn–Li alloying. We detected and observed initial steps of the surface film formation at ～2.8 V vs. Li/Li⁺ followed by gradual film morphology changes at potentials 0.7 < U < 2.5 V. The SEI layer undergoes continuous reformation during the following CV cycles between 0.7 and 2.5 V. The surface film on Sn does not effectively prevent the electrolyte reduction and a large fraction of the reaction products dissolve in the electrolyte. The unstable SEI layer on Sn in EC-based electrolytes may compromise the use of tin-based anodes in Li-ion battery systems unless the interfacial chemistry of the electrode and/or electrolyte is modified.     

Direct determination of arsenate based on its electrocatalytic reduction at the poly(aniline-co-o-aminophenol) electrode

It was found that the copolymer poly(aniline-co-o-aminophenol) (PANOA) can strongly catalyze the reduction of arsenate in a NaCl solution, which was proved by cyclic voltammetry and the determination of activation energy. On the basis of the electrocatalytic reduction of arsenate, the PANOA copolymer was used as a probe to determine directly arsenate. The electrocatalytic activity of the PANOA electrode toward As(V) reduction strongly depended on the pH and the applied potential. Under the optimal conditions, the PANOA electrode can be used to determine directly As(V) concentration in a wide linear range (n = 19) of 0.949 and 495 μM with a correlation coefficient of 0.995 and a limit of detection of 0.495 μM. The sensitivity of the electrode was 0.192 μA μM^?1 cm^?2. The PANOA electrode had the good storage stability and a less negative operation potential of ?0.15 V (vs. SCE).     

Electrochemical synthesis of Au/polyaniline–poly(4-styrenesulfonate) hybrid nanoarray for sensitive biosensor design

Au/polyaniline (PANI)–poly(4-styrenesulfonate) (PSS) hybrid nanoarray is fabricated for biomolecular sensing in neutral aqueous solutions. Firstly, an array of one-dimensional Au nanorods (diameter = ca. 200 nm, length = ca. 3 μm) is formed by a template-electrodeposition method using a porous anodic alumina membrane, and then a thin PANI–PSS composite layer is electropolymerized on the surface of the Au nanorods. The resulting Au/PANI–PSS hybrid nanoarray exhibits a quasi-reversible redox electrochemical process at ca. +0.11 V and electrocatalytic oxidation of reduced β-nicotinamide adenine dinucleotide (NADH) is attained with a detection limit of 0.3 μM in a neutral solution.     

Non-aqueous chromium acetylacetonate electrolyte for redox flow batteries

A single-metal redox flow battery employing chromium(III) acetylacetonate in tetraethylammonium tetrafluoroborate and acetonitrile has been investigated using electrochemical techniques. Cyclic voltammetry was used to evaluate electrode kinetics. Four redox couples were observed in the stable potential window. The Cr^II/Cr^III, Cr^I/Cr^II, Cr^III/Cr^IV and Cr^IV/Cr^V redox couples all appeared to be quasi-reversible, with the Cr^III/Cr^IV couple exhibiting comparatively slow kinetics. A cell potential of 3.4 V was measured for the one-electron disproportionation of the neutral Cr^III complex. The diffusion coefficient for chromium acetylacetonate in the supporting electrolyte solution was estimated to be in the range of 5.0–6.2 × 10^?7 cm² s^?1 at room temperature. The charge–discharge characteristics of this system were evaluated in an H-type glass cell, and coulombic and energy efficiencies of approximately 55% and 20%, respectively, were obtained.     

Single microparticle applied in magnetic-switchable electrochemistry

In this work we demonstrated the micromanipulation of a single magnetic microparticle (Fe₃O₄) modified with Prussian blue (PB) for use in magnetic-switchable electrochemistry. A single Fe₃O₄-PB microparticle with 120 μm was isolated in an electrochemical microcell (20 μL), in which a fine control of PB electrochemical process on carbon electrode (Ø = 4.0 mm) was obtained. For cyclic voltammetry, redox processes attributed to PB/PW (Prussian blue/Prussian white) one electron redox couple were observed, however the capacitive currents were very high. On the other hand, by using differential pulse voltammetry, a maximum faradaic current for anodic peak of 200 nA cm^− 2 at 0.06 V was observed. Several and high stable chronoamperograms were obtained by “switch on” and “switch off” magnetic commutative states for a single microparticle, showing that the system developed here can be very promising for application in electrochemistry.     

Activity of Pt anode catalyst modified by underpotential deposited Pb in a direct formic acid fuel cell

We characterized the electrocatalytic activity of platinum electrode modified by underpotential deposited lead (PtPb_upd) for a formic acid (HCOOH) oxidation and investigated the influence on the power performance of direct formic acid fuel cells (DFAFC). Based on the electrochemical analysis using cyclic voltammetry and chronoamperometry, PtPb_upd electrode modified by underpotential deposition (UPD) exhibited significantly enhanced catalytic activity for HCOOH oxidation below anodic overpotential of 0.4 V (vs. SCE). Multi-layered PtPb_upd electrode structure of Pt/Pb_upd/Pt resulted in more stable and enhanced performance using 50% reduced loading of anode catalyst. The performance of multi-layered PtPb_upd anode is about 120 mW/cm² at 0.4 V and it also showed a sustainable cell activity of 0.52 V at an application of constant current loading of 110 mA/cm².     

Electrochemical investigation of carbon nanotube nanoweb architecture in biological media

The as-synthesised carbon nanotube nanoweb modified carbon fibre paper (CNT-NW/CFP) was investigated to study the effect of surface protein adsorption in electrochemical activities using immunoglobulin G (IgG) and human serum albumin (HSA). Detail chemical characterisation was carried out using 125I radiolabeling, cyclic voltammetry and electrochemical impedance spectroscopy. Both HSA and IgG were adsorbed onto the electrode at levels of approximately 120 mg/m². Cyclic voltammetry indicated that the surface-adsorbed protein had a detrimental effect on oxidation/reduction of ferri/ferricyanide whilst EIS spectra revealed a slight increase in impedance and decrease in capacitance.