Visible LED light photoelectrochemical sensor for detection of L-Dopa based on oxygen reduction on TiO2 sensitized with iron phthalocyanine

The present work describes the development of a new strategy to photoelectrochemical detection of L-Dopa at low potential based on oxygen reduction on TiO₂ sensitized with iron phthalocyanine (FePc/TiO₂). The FePc/TiO₂ composite shows a photocurrent 10-fold higher than that of pure TiO₂ nanoparticles and it was 4-fold higher than that of FePc exploiting visible light. The band gaps of pure TiO₂ nanoparticles, FePc and FePc/TiO₂, calculated according to the Kubelka–Munk equation, were 3.22 eV, 3.11 eV and 2.82 eV, respectively. The FePc/TiO₂ composite showed a low charge transfer resistance in comparison to the photoelectrode modified with FePc or TiO₂. Under optimized conditions, the photoelectrochemical sensor shows a linear response range from 20 up to 190 μmol L^− 1 with a sensitivity of 31.8 μA L mmol^− 1 and limit of detection of 1.5 μmol L^− 1 for the detection of L-Dopa.     

Enhanced electrochemical performance of carbon-coated TiO2 nanobarbed fibers as anode material for lithium-ion batteries

We report the electrochemical performance of carbon-coated TiO₂ nanobarbed fibers (TiO₂@C NBFs) as anode material for lithium-ion batteries. The TiO₂@C NBFs are composed of TiO₂ nanorods grown on TiO₂ nanofibers as a core, coated with a carbon shell. These nanostructures form a conductive network showing high capacity and C-rate performance due to fast lithium-ion diffusion and effective electron transfer. The TiO₂@C NBFs show a specific reversible capacity of approximately 170 mAh g^− 1 after 200 cycles at a 0.5 A g^− 1 current density, and exhibit a discharge rate capability of 4 A g^− 1 while retaining a capacity of about 70 mAh g^− 1. The uniformly coated amorphous carbon layer plays an important role to improve the electrical conductivity during the lithiation–delithiation process.     

Tio2@Sn core–shell nanotubes for fast and high density Li-ion storage material

TiO₂@Sn core–shell nanotube material prepared by thermal decomposition of SnCl₄ on TiO₂ nanotubes at 300 °C has been demonstrated superior Li-ion storage capability of 176 mA h/g even at high current rate of 4000 mA/g (charge and discharge of all TiO₂ within 5 min) in spite of using low carbon content (5 wt%). This value corresponds to volumetric energy densities of 317 mA h/cm³, and its value was 3.5-fold larger than that of the bare TiO₂ nanotubes.     

Phosphatization: A promising approach to enhance the performance of mesoporous TiO2 anode for lithium ion batteries

We report phosphatization is a promising method to enhance the performance of mesoporous TiO₂ anode for lithium ion batteries. The resulting phosphated mesoporous TiO₂ possessed higher reversible capacity and better cycling stability than the pure mesoporous TiO₂. When cycled at 30 mA/g between 3.0 and 1.0 V, the initial capacity of phosphate mesoporous TiO₂ was 249 mA h/g, significantly higher than that of pure mesoporous TiO₂ (204 mA h/g). After 40 cycles, the capacity retention ratio of phosphate mesoporous TiO₂ reached 83.7%, while pure mesoporous TiO₂ had merely a capacity retention ratio of 62.3%. We believe that this phosphatization process could be used to enhance the electrochemical performance of other metal oxides for lithium ion batteries.     

A novel approach for determining total titanium from titanium dioxide nanoparticles suspended in water and biosolids by digestion with ammonium persulfate

Titanium dioxide (i.e. TiO₂) in nano-form is a constituent of many nanomaterials that are used in sunscreens, cosmetics, industrial products and in biomedical applications. Quantification of TiO₂ nanoparticles in various matrixes is a topic of great interest for researchers studying the potential health and environmental impacts of nanoparticles. However, analysis of TiO₂ as Ti⁴⁺ is difficult because current digestion techniques require use of strong acids that may be a health and safety risk in the laboratory. To overcome this problem, we developed a new method to digest TiO₂ nanoparticles using ammonium persulfate as a fusing reagent. The digestion technique requires short times to completion and optimally requires only 1 g of fusing reagent. The fusion method showed >95% recovery of Ti⁴⁺ from 6 μg mL^?1 aqueous suspensions prepared from 10 μg mL^?1 suspension of different forms of TiO_2, including anatase, rutile and mixed nanosized crystals, and amorphous particles. These recoveries were greater than open hot-plate digestion with a tri-acid solution and comparable to microwave digestion with a tri-acid solution. Cations and anions commonly found in natural waters showed no significant interferences when added to samples in amounts of 10 ng to 110 mg, which is a much broader range of these ions than expected in environmental samples. Using ICP-MS for analysis, the method detection limit (MDL) was determined to be 0.06 ng mL^?1, and the limit of quantification (LOQ) was 0.20 ng mL^?1. Analysis of samples of untreated and treated wastewater and biosolids collected from wastewater treatment plants yielded concentrations of TiO₂ of 1.8 and 1.6 ng mL^?1 for the wastewater samples, respectively, and 317.4 ng mg^?1 dry weights for the biosolids. The reactions between persulfate ions and TiO₂ were evaluated using stoichiometric methods and FTIR and XRD analysis. A formula for the fusing reaction is proposed that involves the formation of sulfate radicals.     

Temporal evolution study of the plasma induced by CO2 pulsed laser on targets of titanium oxides

This paper reports studies on time-resolved laser induced breakdown spectroscopy (LIBS) of plasmas induced by IR nanosecond laser pulses on the titanium oxides TiO and TiO₂ (anatase). LIBS excitation was performed using a CO₂ laser. The laser-induced plasma was found strongly ionized yielding Ti⁺, O⁺, Ti^2 +, O^2 +, Ti^3 +, and Ti^4 + species and rich in neutral titanium and oxygen atoms. The temporal behavior of specific emission lines of Ti, Ti⁺, Ti^2 + and Ti^3 + was characterized. The results show a faster decay of Ti^3 + and Ti^2 + ionic species than that of Ti⁺ and neutral Ti atoms. Spectroscopic diagnostics were used to determine the time-resolved electron density and excitation temperatures. Laser irradiation of TiO₂-anatase induces on the surface sample the polymorphic transformation to TiO₂-rutile. The dependence on fluence and number of irradiation pulses of this transformation was studied by micro-Raman spectroscopy.     

TiO2@CdS core–shell nanorods films: Fabrication and dramatically enhanced photoelectrochemical properties

In this paper, we prepared TiO₂@CdS core–shell nanorods films electrodes using a simple and low-cost chemical bath deposition method. The core–shell nanorods films electrodes were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and UV–vis spectrometry techniques. After applying these TiO₂@CdS core–shell nanorods electrodes in photovoltaic cells, we found that the photocurrent was dramatically enhanced, comparing with those of bare TiO₂ nanorods and CdS films electrodes. Moreover, TiO₂@CdS core–shell nanorods film electrode showed better cell performance than CdS nanoparticles deposited TiO₂ nanoparticles (P25) film electrode. A photocurrent of 1.31 mA/cm², a fill factor of 0.43, an open circuit photovoltage of 0.44 V, and a conversion efficiency of 0.8% were obtained under an illumination of 32 mW/cm², when the CdS nanoparticles deposited on TiO₂ nanorods film for about 20 min. The maximum quantum efficiency of 5.0% was obtained at an incident wavelength of 500 nm. We believe that TiO₂@CdS core–shell heterostructured nanorods are excellent candidates for studying some fundamental aspects on charge separation and transfer in the fields of photovoltaic cells and photocatalysis.     

Molecular dynamics simulations of adsorption of hydrophobic 1,2,4-trichlorobenzene (TCB) on hydrophilic TiO2 in surfactant emulsions and experimental process efficiencies of photo-degradation and -dechlorination

Molecular dynamics simulations have been carried out to assess event details in the adsorption of the hydrophobic substrate 1,2,4-trichlorobenzene (TCB) on the hydrophilic TiO₂ particle surface in the presence of the biosurfactant 4-O-(4′,6′-di-O-acetyl-2′,3′-di-O-alkanoyl-β-d-mannopyranosyl)-d-erythritol (MEL) and the SDS (sodium dodecylsulfate) surfactant in aqueous media at ambient temperature with interaction forces between organic molecules and TiO₂ calculated from Lennard–Jones and Coulomb potential models. The surfactant and the TCB substrate were arranged in the vicinity of TiO₂ using 768 water molecules in the simulations. Results indicate that the MEL molecules adsorb on the TiO₂ surface in ca. 5 ps (k = 2 × 10¹¹ s^?1) through the oxygen atoms of the hydrophilic functions. Contact distance between the MEL and the TiO₂ surface shortened further after 10 ps with adsorption controlled mostly by van der Waals’ forces. The TCB molecules are trapped within the alkyl chains of the MEL system, which subsumes TCB to a greater extent by the repulsion of water, thereby facilitating the TCB molecules to approach the highly hydrophilic and positively charged TiO₂ particle surface. Along with the simulations, also examined was the photodegradation of this hydrophobic TCB substrate that takes place at the TiO₂/water interface in the presence of the MEL biosurfactant. For comparison, the advantages of the MEL in this task and of the commonly used SDS surfactant were determined under otherwise identical experimental conditions (200 mg L^?1 of surfactants) by examining the dynamics of the photo-induced degradation and dechlorination of TCB. The photodegradation of TCB was nearly quantitative in MEL/TiO₂ in contrast to only ca. 22% complete in SDS/TiO₂ dispersions. It is deduced that wastewater treatments with the highly hydrophilic TiO₂ are seriously limited in their photodegradation of hydrophobic pollutants, an issue easily resolvable by the presence of biodegradable surfactants.     

Doping level effect on visible-light irradiation W-doped TiO2–anatase photocatalysts for Congo red photodegradation

A series of W-modified TiO₂ (W–TiO₂) photocatalysts were synthesized by a simple sol–gel method. The new photocatalysts were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–vis-diffuse reflectance spectroscopy (DRS), and Brunauer, Emmett and Teller (BET) surface area analyzer. The photoactivity of the W–TiO₂ photocatalysts was evaluated by the photocatalytic oxidation of Congo red (CR) dye. It was found that the average size of the prepared photocatalysts is 10 nm. Moreover, they have high surface areas (∼ 216 m² g⁻¹) and their light-absorption extends to the visible region compared to pure TiO₂. The effects of W-loading and of the calcination temperature of the prepared photocatalysts on their photocatalytic activity were also studied. The obtained results show that the W_0.5–TiO₂ photocatalyst calcined at 350 °C is much highly photoactive than non-doped or highly doped TiO₂. The enhanced photocatalytic activity of the weakly doped TiO₂ may be attributed to the increase in the charge separation efficiency and the presence of surface acidity on the W_0.5–TiO₂ photocatalyst.     

Photocurrent generated on a carotenoid-sensitized TiO2 nanocrystalline mesoporous electrode

Photocurrent was observed upon monochromatic illumination of an ITO electrode coated with a TiO₂ nanocrystalline mesoporous membrane with carotenoid 8′-apo-β-caroten-8′-oic acid (ACOA) deposited as a sensitizer (illuminated area 0.25 cm²) and immersed in an aqueous 10 mM hydroquinone (H₂Q), 0.1 M NaH₂PO₄ solution (pH = 7.4) purged with argon, using a platinum flag counter electrode (area 3.3 cm²) and a SCE reference electrode. The carotenoid-sensitized short-circuit photocurrent reached 4.6 μA/cm² upon a 40 μW/cm² incident light beam at 426 nm, with an IPCE (%, incident monochromatic photon-to-photocurrent conversion efficiency) as high as 34%. The short-circuit photocurrent was stable during 1 h of continuous illumination with only a 10% decrease. An open-circuit voltage of 0.15 V was obtained (upon 426 nm, 40 μW/cm² illumination) which remained at a constant value for hours. The observed open-circuit voltage is close to the theoretical value (0.22 V) expected in such a system. The action spectrum resembled the absorption spectrum of ACOA bound on the TiO₂ membrane with a maximum near 426 nm. No decay of the ACOA on the TiO₂ surface was observed after 12 h, presumably because of rapid regeneration of ACOA from ACOA⁺ at the surface by electron transfer from H₂Q.     

Photocatalytic decomposition of 4-chlorophenol over an efficient N-doped TiO2 under sunlight irradiation

Using a new nitrogen precursor of a mixture of ammonia and hydrazine hydrate, N-doped TiO₂ photocatalyst with a high efficiency under visible light was synthesized by a precipitation method. The analysis of X-ray photoelectron spectroscopy (XPS) suggested that the doping concentration of nitrogen was 0.45 at%, while it was 0.21 at% or 0.24 at% using single ammonia or hydrazine hydrate as nitrogen precursor. The patterns of the electron paramagnetic resonance spectroscopy (EPR) indicated that the paramagnetic species of NO₂^2?, NO and Ti³⁺ existed as the proposed active species. The ultraviolet–visible (UV–vis) spectra revealed that the band-gap of the N-doped TiO₂ was 3.12 eV, which was slightly lower than 3.15 eV of pure TiO₂. The N-doped TiO₂ showed higher efficiency under both ultraviolet (UV) and visible light irradiations. Moreover, the degradation grade of 4-chlorophenol (4-CP) using the as-synthesized N-doped TiO₂ under sunlight irradiation for 6 h was 82.0%, which was higher than 66.2% of the pure TiO₂, 60.1% or 65.2% of the N-doped TiO₂ using single ammonia or hydrazine hydrate as precursor. Density functional theory (DFT) calculations were performed to investigate the visible light response of the N-doped TiO₂. Our study demonstrated that the visible activities vary well with the concentrations of NO₂^2? species incorporated by N–TiO₂ series photocatalysts and the higher activity of the as-prepared N-doped TiO₂ was attributed to the enhancement of the concentration of NO₂^2? species.     

Photocatalytic degradation of paraquat and genotoxicity of its intermediate products

The photocatalytic degradation of paraquat (1,1-dimethyl-4,4′-bipyridylium dichloride) aqueous solutions in the presence of polycrystalline TiO₂ Degussa P25 irradiated by near-UV light was investigated. The substrate and total organic carbon concentrations were monitored by UV spectroscopy and TOC measurements, respectively: the complete photocatalytic mineralization of paraquat (20 ppm) was achieved after ca. 3 h of irradiation by using 0.4 g l⁻¹ of catalyst amount at natural pH (ca 5.8). On the contrary no significant photodegradation of paraquat was observed in the absence of TiO₂ under similar experimental conditions. To evaluate the genotoxicity of paraquat and its intermediates produced during heterogeneous photocatalytic treatment, in vitro tests such as Ames test, with and without rat liver microsomal fractions (S9 mix), and micronucleus test, were used. Results obtained with Salmonella typhimurium (strain TA100) showed that paraquat and photocatalytic products were unable to induce gene mutations when photocatalysis was used in the presence of the optimum amount of TiO₂, i.e. 0.4 g l⁻¹, whereas an increase of revertants his⁺ per plate was observed after 300 min irradiation in the presence of very low amount of TiO₂ (0.04 g l⁻¹). The negative results from micronucleus test suggest that mutagenic, but non-clastogenic, late intermediates of paraquat photo-oxidation were formed when the photocatalytic runs of paraquat degradation were carried out by using 0.04 g l⁻¹ of photocatalyst.     

Effects of electron beam irradiation on the photoelectrochemical properties of TiO2 film for DSSCs

TiO₂ has been widely utilized for various industrial applications such as photochemical cells, photocatalysts, and electrochromic devices. The crystallinity and morphology of TiO₂ films play a significant role in determining the overall efficiency of dye-sensitized solar cells (DSSCs). In this study, the preparation of nanostructured TiO₂ films by electron beam irradiation and their characterization were investigated for the application of DSSCs. TiO₂ films were exposed to 20–100 kGy of electron beam irradiation using 1.14 MeV energy acceleration with a 7.46 mA beam current and 10 kGy/pass dose rates. These samples were characterized using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), and X-ray photoelectron spectroscopy (XPS) analysis. After irradiation, each TiO₂ film was tested as a DSSC. At low doses of electron beam irradiation (20 kGy), the energy conversion efficiency of the film was approximately 4.0% under illumination of simulated sunlight with AM 1.5 G (100 mW/cm²). We found that electron beam irradiation resulted in surface modification of the TiO₂ films, which could explain the observed increase in the conversion efficiency in irradiated versus non-irradiated films.     

A study of the photodeposition over Ti/TiO2 electrode for electrochemical detection of heavy metal ions

Here we reported that UV light irradiation can significantly enhance sensitivity of Ti/TiO₂ electrode for determination of trace heavy metal ions (such as Cu^2 +, Pb^2 + and Cd^2 +) owing to the photodeposition of metal ions on the surface of electrodes. The sensitivity of heavy metal ions can be selectively enhanced over the Ti/TiO₂ electrode, which is attributed to matching between potential of heavy metal ions and the position of the conduction band of TiO₂.     

Voltammetric sensor for buzepide methiodide determination based on TiO2 nanoparticle-modified carbon paste electrode

In this work, we have prepared nano-material modified carbon paste electrode (CPE) for the sensing of an antidepressant, buzepide methiodide (BZP) by incorporating TiO₂ nanoparticles in carbon paste matrix. Electrochemical studies indicated that the TiO₂ nanoparticles efficiently increased the electron transfer kinetics between drug and the electrode. Compared with the nonmodified CPE, the TiO₂-modified CPE greatly enhances the oxidation signal of BZP with negative shift in peak potential. Based on this, we have proposed a sensitive, rapid and convenient electrochemical method for the determination of BZP. Under the optimized conditions, the oxidation peak current of BZP is found to be proportional to its concentration in the range of 5 × 10⁻⁸ to 5 × 10⁻⁵ M with a detection limit of 8.2 × 10⁻⁹ M. Finally, this sensing method was successfully applied for the determination of BZP in human blood serum and urine samples with good recoveries.     

Mesoporous TiO2 nano networks: Anode for high power lithium battery applications

Anatase phase mesoporous TiO₂ with I41/amd space group was synthesized via the urea assisted hydrothermal method. The existence of mono phasic TiO₂ sub-microspheres of uniform particle size (ca. 400 nm) encompassing an average crystallite size of 14 nm was demonstrated using the XRD, FE-SEM and TEM analysis. Surface area of ca. 116.49 m²/g along with a pore size of 7 nm was calculated using the BET and adsorption isotherm measurements which authenticated the mesoporous nature of the synthesized material. Suitable calcination temperature for the better electrochemical property was established via the optimization process. Accordingly, the mesoporous TiO₂ calcined at 400 °C displayed improved cycleability with excellent rate capability ever reported, even at 20 C-rate of discharge. The reason for the superior rate capability is corroborated to the highly mesoporous nature of the TiO₂ sub-microspheres that has imparted desirable surface area apposite for enhanced ionic and electronic diffusion.     

Surface properties and photoactivity of TiO2 treated with electron beam

The improvement of the TiO₂-photoactivitiy by electron beam treatment (1 MeV) as a function of the absorbed radiation dose (MGy) is reported. The radiation-induced effects in the TiO₂ crystal structure, e.g. change of the Ti³⁺/Ti⁴⁺ ratio, increase of the photoactivity, etc. were investigated. Three methods were implemented in this respect: for the change of the TiO₂ crystal structure X-ray photoelectron spectroscopy and photoluminescence spectroscopy were applied. The photocatalytic activity of the EB-treated TiO₂ was tested by taking the degree of methylene blue photodegradation as a measure of the achieved effect. The obtained experimental data of all testing methods showed that in TiO₂ at an absorbed dose of 0.5 MGy optimum changes in crystal structure of the catalyst occur, resulting in the highest photocatalytic efficiencies.     

A new composite electrode of Ni-Ferrite/TiOx/Si(111): Preparations and photoelectrochemical studies

A composite electrode of Ni-ferrite/TiO_x/Si(111) was synthesized by grafting Ni²⁺Fe²⁺Fe³⁺–LDH–TiCl₃ (LDH: Layered Double Hydroxides) on n-Si(111) surface and calcined under 1100 °C. Photoelectric research results indicated that the electrode had good photovoltaic effects in an electrolyte solution containing 7.6 M HI and 0.05 M I₂, while platinum plate was used as counter-electrode. The observed photo-voltages (U_pv) and photocurrent densities (j_pc) of the electrode were at ?0.75 V and 5.35 mA/cm², respectively. Compared with electrodes of oxidized n-Si(111) crystal and n-Si(111) wafer covered by Ni-ferrites, j_pc of the electrode Ni-ferrite/TiO_x/Si(111) was increased greatly.     

Thermodynamic properties of calcium titanates: CaTiO3, Ca4Ti3O10, and Ca3Ti2O7

The chemical potentials of CaO in two-phase fields (TiO₂ + CaTiO₃), (CaTiO₃ + Ca₄Ti₃O₁₀), and (Ca₄Ti₃O₁₀ + Ca₃Ti₂O₇) of the pseudo-binary system (CaO + TiO₂) have been measured in the temperature range (900 to 1250) K, relative to pure CaO as the reference state, using solid-state galvanic cells incorporating single crystal CaF₂ as the solid electrolyte. The cells were operated under pure oxygen at ambient pressure. The standard Gibbs free energies of formation of calcium titanates, CaTiO₃, Ca₄Ti₃O₁₀, and Ca₃Ti₂O₇, from their component binary oxides were derived from the reversible e.m.f.s. The results can be summarised by the following equations: CaO(solid) + TiO₂(solid) → CaTiO₃(solid), ΔG° ± 85/(J · mol^?1) = ?80,140 ? 6.302(T/K); 4CaO(solid) + 3TiO₂(solid) → Ca₄Ti₃O₁₀(solid), ΔG° ± 275/(J · mol^?1) = ?243,473 ? 25.758(T/K); 3CaO(solid) + 2TiO₂(solid) → Ca₃Ti₂O₇(solid), ΔG° ± 185/(J · mol^?1) = ?164,217 ? 16.838(T/K).The reference state for solid TiO₂ is the rutile form. The results of this study are in good agreement with thermodynamic data for CaTiO₃ reported in the literature. For Ca₄Ti₃O₁₀ Gibbs free energy of formation obtained in this study differs significantly from that reported by Taylor and Schmalzried at T = 873 K. For Ca₃Ti₂O₇ experimental measurements are not available in the literature for direct comparison with the results obtained in this study. Nevertheless, the standard entropy for Ca₃Ti₂O₇ at T = 298.15 K estimated from the results of this study using the Neumann–Koop rule is in fair agreement with the value obtained from low-temperature heat capacity measurements.