CtrA gene based electrochemical DNA sensor for detection of meningitis

Electrochemical DNA sensor has been fabricated by immobilizing thiolated single stranded oligonucleotide (ssDNA) probe onto gold (Au) coated glass electrode for meningitis detection using hybridization with complementary DNA (CtrA) in presence of methylene blue (MB). These electrodes (ssDNA/Au and dsDNA/Au) have been characterized using atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FT-IR), electrochemical impedance spectroscopy (EIS) and cyclic voltammetric (CV) technique. The DNA/Au electrode can detect the complementary DNA in the range of 7–42 ng/μl in 5 min (hybridization) with response time 60 s and electrode is stable for about 4 months when stored at 4 °C. The sensitivity of dsDNA/Au electrode is 115.8 μA/ng with 0.917 regression coefficient (R).     

Cyclic voltammetric studies of carbohydrate–protein interactions on gold surface

A simple electrochemical method for the determination of association constants between carbohydrates and carbohydrate-binding proteins using cyclic voltammetry (CV) is described. The binding of concanavalin A (Con A) and cholera toxin (CT) to their specific α-mannose and β-galactose derivatives self-assembled on gold electrodes is electrochemically monitored with a redox probe of K₃Fe(CN)₆/K₄Fe(CN)₆. Upon binding of the proteins to the carbohydrate-modified electrodes, the redox current in CV decreases. The binding-induced change in electrochemical signal is thus used to construct Langmuir adsorption isotherm for the carbohydrate–protein interactions and to obtain the association constants. The association constants of carbohydrate–protein interactions determined by CV ((5.8 ± 1.2) × 10⁷ M^− 1 for mannose–Con A, (2.6 ± 0.5) × 10⁸ M^− 1 for galactose-CT) were in good agreement with those measured with electrochemical impedance spectroscopy and quartz crystal microbalance.     

Electrochemical deposition of PbTe onto n-Si(1 0 0) wafers

Electrochemical deposition of PbTe from 50 mM Pb(NO₃)₂ + 1 mM TeO₂ + 0.1 M HNO₃ solution onto n-Si(1 0 0) wafers was studied using cyclic voltammetry (CV), chronoamperometry, ex situ SEM, XRD and EDX. Electrochemical behavior of n-Si(1 0 0) electrode in electrolytes 50 mM Pb(NO₃)₂ + 0.1 M HNO₃ and 1 mM TeO₂ + 0.1 M HNO₃ was also studied. No underpotential deposition (UPD) of Pb and Te onto n-Si was observed in the investigated systems indicating weak Pb–Si and Te–Si interactions. Deposition of Pb and Te on n-Si occurred with overvoltage via 3D island growth. Electrosynthesis of PbTe (NaCl-like structure, a = 0.650 nm) takes place due to codeposition of Pb and Te at potentials E > E_{Pb²⁺/Pb⁰} (lead UPD onto tellurium). Cathodic deposition of PbTe onto n-Si(1 0 0) is irreversible – there is no anodic current in the CV curve. Oxidation of PbTe on n-Si is observed only under illumination, when photoelectrons and photoholes are generated in silicon substrate.     

EC-STM observation on electrochemical response of fluidic phospholipid monolayer on Au(1 1 1) modified with 1-octanethiol

Electrochemical scanning tunneling microscopy (EC-STM) was applied to observe phospholipid layers over thiol-modified gold substrates as a model biological cell membrane. On a monolayer of 1-octanethiol on Au (1 1 1), a synthetic lipid, 1,2-dihexanoyl-sn-glycero-3-phosphocholine, was introduced in a neutral 0.05 M NH₄ClO₄ buffer solution. The lipid molecules formed a fluidic layer at 0.0 V vs. RHE of the substrate electrode potential. By cycling the electrode potential between +0.2 V and −0.2 V, the lipid layer reversibly changed over between the fluidic phase and a striped/grainy structure. This structural change might involve partial decomposition and oligomerization of phospholipids. This method will contribute for molecular biology by revealing the nanometer-scale structure of cell membrane.     

Enhanced electron transfer between gold nanoparticles and horseradish peroxidase reconstituted onto alkanethiol-modified hemin

Robust molecular bioelectronic devices require a programmable and efficient electronic communication between biological molecules and electrodes. With proteins it is often compromised by their uncontrollable assembly on electrodes that does not provide neither uniform nor efficient electron flow between proteins and electrodes. Here, horseradish peroxidase reconstituted onto C₁₁-alkanethiol-conjugated hemin and self-assembled onto the gold nanoparticle (NP)-modified electrodes via the exposed alkanethiol tail exhibits enhanced electron transfer (ET), proceeding via the gold NP relay with the ET rate constant approaching 115 s^− 1 vs. 14 s^− 1 shown on bare gold, by this offering an advanced controllable design of interfaces for bioelectronic devices based on heme-containing enzymes with a non-covalently bound heme.     

Surface poisoning during electrocatalytic monosaccharide oxidation reactions at gold electrodes in alkaline medium

In the present study, the surface poisoning of electrocatalytic monosaccharide oxidation reactions at gold electrodes were investigated. In the cyclic voltammetric studies, the electrocatalytic oxidation of aldohexose and aldopentose type monosaccharides, aminosugars, acetyl-glucosamine and glucronamide were observed at gold plate electrodes in alkaline medium. However, in controlled-potential electrolytic studies ranging −0.3 to −0.2 V in reaction solutions, current flows during electrolyses decreased quickly with time, except when glucosamine was used as a substrate.Results from surface enhanced infrared adsorption (SEIRA) spectroscopic measurements at an evaporated gold electrode for the electrocatalytic oxidation of glucose in 0.1 mol dm⁻³ NaOH at −0.3 V and Gaussian simulated spectra indicated that the gluconic acid as a 2-electron oxidation product and/or its analogs adsorbed onto the gold surface. Electrochemical quartz crystal microbalance (EQCM) measurement results, along with surface adsorption results from surface poisoning at the gold electrode during electrolytic reactions, suggested that gluconic acid and/or its analogs adsorbed vertically onto electrode surfaces in a full monolayer packing-like conformation. In the case of the electro oxidation of glucosamine in 0.1 mol dm⁻³ NaOH at −0.2 V, the obtained SEIRA spectra and EQCM results, clearly indicated that the glucosaminic acid as a 2-oxidation glucosamine product did not strongly bind onto the gold electrode surface.     

Nanostructured electropolymerized film of 5-amino-2-mercapto-1,3,4-thiadiazole on glassy carbon electrode for the selective determination of l-cysteine

We report the electropolymerization of 5-amino-2-mercapto-1,3,4-thiadiazole (AMT) in 0.1 M H₂SO₄ on glassy carbon electrode (GCE) and utilization of the resulting polymer film for the selective determination of l-cysteine (CY) at physiological pH for the first time. The electropolymerized film was characterized by cyclic voltammetry (CV), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). AFM image shows a homogeneous film containing spherical structure with a thickness of ～25 nm for p-AMT deposited by 15 cycles. The binding energies at 163.5, 400.2 and 398.8 eV in the XPS corroborate that the p-AMT was linked by S–S, HN–NH and NN groups. The p-AMT film successfully separates the voltammetric signals of CY and ascorbic acid (AA) with a potential difference of 480 mV which is higher than the previous reports.     

High performance mesoporous Pt electrode for methanol electrooxidation. A DEMS study

Electrodeposited mesoporous (MP) Pt electrodes were evaluated as catalysts for CO and methanol electrooxidation. Electrochemical analysis reveals a mass activity of 41 Ag⁻¹ at 0.55 V in 1 M CH₃OH, similar to carbon supported catalysts. However, the high current densities are related to low CO₂ conversion efficiencies, as was established by using differential electrochemical mass spectrometry in a thin layer flow cell configuration (TLFC-DEMS). These results can be understood taking into account the especially accessible porous structure of the MP Pt, where the possibility of readsorption of partially oxidized products is low.     

High performance bioanode based on direct electron transfer of fructose dehydrogenase at gold nanoparticle-modified electrodes

The direct electron transfer reaction of fructose dehydrogenase (FDH) from Gluconobacter sp. on alkanethiol-modified gold nanoparticles (AuNPs) was examined. AuNP-modified electrodes were simply fabricated by depositing citrate-reduced gold nanoparticles onto a gold electrode and carbon fiber paper and then covering the surface with a self-assembled monolayer of alkanethiols. The immobilization of AuNPs provided a large effective surface area for the adsorption of FDH. Catalytic oxidation currents based on the direct electron transfer reaction of FDH were observed from a potential about ?100 mV (vs. Ag/AgCl, 3 M NaCl) in the presence of d-fructose without a mediator. The current density reached as high as 14.3 ± 0.93 mA/cm² (at +500 mV), which was achieved in the presence of 200 mM d-fructose by immobilization of FDH on 2-mercaptoethanol-modified AuNP/carbon fiber paper electrodes.     

Single-walled carbon nanotube-arrayed microelectrode chip for electrochemical analysis

The development of a single-walled carbon nanotube (SWCNT)-arrayed microelectrode chip is reported here. SWCNT-arrayed electrodes were formed directly on Pt surfaces, and were also arrayed on the chip. The electrochemical characteristics of the devices were investigated using potassium ferricyanide, K₃[Fe(CN)₆] in connection with cyclic voltammetry (CV). The electrochemical signals of electro-active amino acids; L-Tyrosine (Tyr), L-Cysteine (Cys) and L-Tryptophan (Trp) were detected using differential pulse voltammetry (DPV). The chip operated at a lower oxidation potential (vs. Ag/AgCl) compared with conventional carbon and Pt disc electrodes in 50 mM phosphate buffer solution (PBS, pH 7.4). The linear response was observed between 0.1–1 μM and 100 μM for the amino acids with correlation coefficients higher than 0.99. The electrochemical measurements of K₃[Fe(CN)₆] and amino acids revealed that the peak current intensities using SWCNT-arrayed electrodes were about 100-fold higher than those using bare Pt-arrayed microelectrodes. Additionally, the surface area dependence of the peak current responses was plotted. We concluded that our chips with SWCNT-arrayed microelectrodes provided a promising platform for electrochemical applications.     

Quasi-reversible two-electron reduction of oxygen at gold electrodes modified with a self-assembled submonolayer of cysteine

The electrochemical reduction of molecular oxygen (O₂) has been performed at gold electrodes modified with a submonolayer of a self-assembly (sub-SAM/Au) of a thiol compound (typically cysteine (CYST)) in O₂-saturated 0.5 M KOH. At bare gold electrode O₂ reduction reaction proceeds irreversibly, while this reaction is totally hindered at gold electrodes with a compact structure of CYST over its surface. The partial reductive desorption of the compact CYST monolayer was achieved by controlling the potential of the CYST/Au electrode, leading to the formation of a submonolayer coverage of the thiol compound over the Au electrode surface (sub-SAM/Au), at which the CYST molecules selectively block the Au(1 0 0) and Au(1 1 0) fractions (the so-called rough domains) of the polycrystalline Au while the Au(1 1 1) component (the so-called smooth domains) remains bare (i.e., uncovered with CYST). This sub-SAM/Au electrode extraordinarily exhibits a quasi-reversible two-electron reduction of molecular oxygen (O₂) in alkaline medium with a peak separation (ΔE_p) between the cathodic and anodic peak potentials (E_p^c,E_p^a) of about 60 mV. The ratio of the anodic current to the cathodic one is close to unity. The formal potential (E^o′) of this reaction is found to equal −150 mV vs. Ag/AgCl/KCl(sat.).     

An insight to the filtration mechanism of Pb(II) at the surface of a clay ceramic membrane through its preconcentration at the surface of a graphite/clay composite working electrode

The use of cyclic voltammetry (CV) and linear scan anodic stripping voltammetry (LSASV) to predict the selectivity of microfiltration ceramic membranes made from a lump of local clay towards Pb(II) ions filtration is described. The membranes were characterized by different techniques followed by CV analysis of the Fe(CN)₆^3-/Fe(CN)₆^4- redox couple and Pb(II) on bare graphite, raw clay, and clay-modified carbon paste electrode (clay-modified CPE). The effect of clay loading in the range of 1–10 % (w/w) on the electrodes is studied, where an enhanced peak current is observed for 5 % w/w clay. Moreover, a decrease in the peak current can be seen for bare graphite electrodes, suggesting that the clay mineral had played a substantial role in the sieving of heavy metal ions through the ceramic membrane. The electroactive surface area of 5% w/w raw clay towards Fe(II) ions was found to be in the order of 3.07 × 10^-2 cm² and higher than 5% w/w clay sintered to 1000 °C and bare graphite. CV analysis shows that both, 5 % w/w raw clay and 5 % w/w clay sintered to 1000 °C exhibited high peak currents towards Pb(II) ions. The mobility of the Pb(II) ions is found to increase when 5% w/w clay sintered to 1000 °C is utilized as membrane/electrode, leading to an increase in the amount of reduced Pb(II) ions on the surfaces of the clay membranes/electrodes. The study suggests successful filtration of Pb(II) ions through the proposed membrane/electrode and a much better accumulation than Fe(II) at the surface of the membrane/electrode before being subjected to filtration.     

Measurement and modelling of mean activity coefficients of aqueous mixed electrolyte solution containing glycine

Electrochemical measurements were made on (H₂O + NaBr + K₃PO₄ + glycine) mixtures at T = 298.15 K by using ion selective electrodes. The mean ionic activity coefficients of NaBr at molality 0.1 were determined at five K₃PO₄ molalities (0.01, 0.03, 0.05, 0.07, and 0.1) mol · kg⁻¹. The activity coefficients of glycine were evaluated from mean ionic activity coefficients of NaBr. The modified Pitzer equation was used to model the experimental data.     

Determination of formal potential of NADH/NAD+ redox couple and catalytic oxidation of NADH using poly(phenosafranin)-modified carbon electrodes

The electrochemical regeneration of NADH/NAD⁺ redox couple has been studied using poly(phenosafranin) (PPS)-modified carbon electrodes to evaluate the formal potential and catalytic rate constant for the oxidation of NADH. The PPS-modified electrodes were prepared by electropolymerization of phenosafranin onto different carbon substrates (glassy carbon (GC) and basal-plane pyrolytic graphite (BPPG)) in different electrolytic solutions. The formal potential was estimated to be ? 0.365 ± 0.002 V vs. SHE at pH 7.0. As for the bare carbon electrodes, the oxidation of NADH at the BPPG electrode was found to be enhanced compared with the GC electrode. For the PPS-modified electrodes, it was found that the electrocatalysis of PPS-modified electrodes for the oxidation of NADH largely depends on the carbon substrate and electrolyte solution employed for their preparation, i.e., the PPS-modified BPPG electrode prepared in 0.2 M NaClO₄/acetonitrile solution exhibits an excellent and persistent electrocatalytic property toward NADH oxidation in phosphate buffer solution (pH 7.0) with a diminution of the overpotential of about 740 and 670 mV compared with those at the bare GC electrode and the PPS-modified GC electrode prepared in 0.2 M H₂SO₄ solution, respectively. A quantitative analysis of the electrocatalytic reaction based on rotating disk voltammetry gave the electrocatalytic reaction rate constants of the order of 10³–10⁴ M^?1 s^? 1 depending on the preparation conditions of the PPS-modified electrodes.     

Flame atomic absorption spectrometry determination of trace amount of gold after separation and preconcentration onto ion-exchange polyethylenimine coated on Al2O3

The object of this work is to develop a simple and selective method for efficient extraction of Au(III) ions in aqueous solution using a new solid-phase extraction sorbent. Polyethylenimine (PEI) ion-exchange polymer was coated on alumina in the presence of NaNO₃. The method is based on sorption of Au³⁺ ions on 50 mg PEI/Al₂O₃. A solution of 0.5 M thiourea, then 1.0 M HCl effectively eluted the gold ion and then aspirated into flame atomic absorption spectroscopy (FAAS). The influence of flow rate of sample solution and eluent, the pH effect, eluent type and sorption capacity was investigated. The effects of various diverse ions for preconcentration and separation of the gold ion were investigated. Relative standard deviation of 4.0 μg mL⁻¹ of gold was 1.46% (n = 10). The detection limit was 26.2 ng L⁻¹ in original solution. The method has been applied successfully for the recovery of trace amount of Au(III) ions from water samples.     

Cathodic carboxylation of gold in thick {Au-CO2}n layers. A model for reversible electrochemical sequestration of CO2

Catalytic reduction of CO₂ (saturated in organic polar solvents, e.g. N,N-dimethylfomamide, containing Me₄NX or NaBF₄) was achieved at smooth gold electrodes and at glassy carbon electrodes galvanostatically capped with a thin layer of gold. Under these quite explicit conditions, very sharp reduction steps were observed near − 1.5 V vs. Ag/AgCl. With small cations listed above, an unexpected behavior was observed, a progressive electrode inhibition occurring upon several scans or after a fixed-potential electrolysis at E < − 1.7 V. This phenomenon could be attributed to the insertion of CO₂ into gold, leading to the formation of a thick iono-metallic multi-strata layer (less conducting than pure metal) that grows with the electrode charge. The formation of this new interface is due to the concur of three elements: transient CO₂ anion radical, the metal, and rather small-sized cations (M⁺ = Na⁺ or TMA⁺), the three possibly associated in a form {Au-CO₂⁻,M⁺} apparently very reactive with oxygen, moisture, and with some organic π-acceptors. Upon multi-scans up to − 2.2 V, the thickness of formed layer progressively increases reaching more than 10^− 7 to 10^− 6 mol cm^− 2. Such multi-layers undergo decomposition in the anodic domain at about + 1.7 V liberating CO₂ beforehand trapped in Au. Coulometric analyses demonstrated that insertion (cathodic) and release (anodic) steps are quite equivalent, which permits to consider this process as chemically reversible sequestration of carbon dioxide.     

Controlled-potential electrosynthesis of glucosaminic acid from glucosamine at a gold electrode

The electrocatalytic oxidation of d-glucosamine (2-amino-2-deoxy-d-glucose) in alkaline and neutral solutions was examined using a carbon felt electrode modified with 2 nm core sized gold nanoparticles (Au_2 nm nanoparticles) and a gold plate electrode. The electrocatalytic voltammetric oxidation curves of d-glucosamine were obtained in both solutions. The voltammetric responses for the electrocatalytic oxidation at a Au_2 nm nanoparticle-modified electrode in both alkaline and neutral solutions were almost the same to those at a gold plate electrode. The oxidized product was identified to be d-glucosaminic acid (2-amino-2-deoxy- d-gluconic acid) generated by the 2-electron oxidation product of d-glucosamine by electrospray ionization time-of-flight mass spectra (ESI TOF-MS). The HPLC results also indicated that the oxidation product was d-glucosaminic acid.The controlled-potential electrolysis of d-glucosamine was performed at the Au_2 nm nanoparticle-modified carbon felt electrodes in both alkaline and neutral solutions. In the alkaline solution, at a potential of −0.2 V, d-glucosaminic acid was formed with a current efficiency of 100%. In the neutral solution, electrolysis at 0.4 V on d-glucosaminic acid was obtained with current efficiencies of 70%.     

Glutathione-s-transferase based electrochemical biosensor for the detection of captan

The proposed electrochemical biosensor based on the inhibition of glutathione-s-transferase (GST) onto SAM modified gold due to captan was developed and determined by CV technique. The bioelectrode exhibited improved fast response time (12 s) with the detection limits 0.25–16 ppm, percentage inhibition >72% and high sensitivity 4.5 uA/ppm at standard optimal conditions. The recovery experiment results were found between 77% and 144% from spiked water sources. The bioelectrode was regenerated by DTT and reusable. The bioelectrodes were characterized by UV–visible, CV, AFM and STM. Thus, the proposed electrochemical biosensor is not only detected captan but also its metabolite and promising for real-time analysis of small molecules of environmental interest.     

Porous cuprous oxide microcubes for non-enzymatic amperometric hydrogen peroxide and glucose sensing

Using porous cuprous oxide (Cu₂O) microcubes, a simple non-enzymatic amperometric sensor for the detection of H₂O₂ and glucose has been fabricated. Cyclic voltammetry (CV) revealed that porous Cu₂O microcubes exhibited a direct electrocatalytic activity for the reduction of H₂O₂ in phosphate buffer solution and the oxidation of glucose in an alkaline medium. The non-enzymatic amperometric sensor used in the detection of H₂O₂ with detection limit of 1.5 × 10^?6 M over wide linear detection ranges up to 1.5 mM and with a high sensitivity of 50.6 μA/mM. This non-enzymatic voltammetric sensor was further utilized in detection of glucose with a detection limit of 8.0 × 10^?7 M, a linear detection range up to 500 μM and with a sensitivity of ?70.8 μA/mM.     

Measurement of activity coefficients of amino acids in aqueous electrolyte solutions: experimental data for the systems (H2O + NaBr + glycine) and (H2O + NaBr + l-valine) at T=298.15 K

Electrochemical cells with two ion-selective electrodes, a cation ion-selective electrode against an anion ion-selective electrode, were used to measure the activity coefficient of amino acids in aqueous electrolyte solutions. Activity coefficient data were measured for (H₂O + NaBr + glycine) and (H₂O + NaBr + l-valine) at T=298.15 K. The maximum concentrations of sodium bromide, glycine, and l-valine were (1.0, 2.4, and 0.4) mol · kg⁻¹, respectively. The results show that the presence of an electrolyte and the nature of both the cation and the anion of the electrolyte have significant effects on the activity coefficients of amino acid in aqueous electrolyte solutions.