A biofuel cell with enhanced power output by grape juice

Glucose oxidase and laccase immobilized at multiwalled carbon nanotubes-ionic liquid gel modified electrodes are used as the catalysts of anode and cathode of biofuel cells (BFCs), respectively. The BFC based on glucose and air is proposed. When ferrocene monocarboxylic acid is adopted as the mediator of anode, the power output of the BFC is ca. 4.1 μW (power density ca. 10.0 μW cm⁻²), which is higher than the value of 2.7 μW (power density ca. 6.6 μW cm⁻²) by taking ferrocene dicarboxylic acid as the mediator. This implies that the mediator with formal potential closing to that of the enzyme does improve the power output. Furthermore, the power output of the BFC is greatly improved by taking grape juice as the fuel of anode rather than glucose. This system also indicates that grape juice as a fuel of the BFC not only is feasible and can also enhances the power output of the BFCs. Besides, it greatly lowers the cost and simplifies the preparation procedure of the BFCs, making the BFC towards “green” bioenergy.     

An enzymatic glucose/O2 biofuel cell: Preparation,characterization and performance in serum

This study demonstrates a new kind of single-walled carbon nanotubes (SWNT)-based compartment-less glucose/O₂ biofuel cell (BFC) with glucose dehydrogenase (GDH) and bilirubin oxidase (BOD) as the anodic and cathodic biocatalysts, respectively, and with poly(brilliant creysl blue) (BCB) adsorbed onto SWNT nanocomposite as the electrocatalyst for the oxidation of NADH. The prepared GDH-polyBCB-SWNT bioanode exhibits an excellent electrocatalytic activity toward the oxidation of glucose biofuel; in 0.10 M phosphate buffer containing 20 mM NAD⁺ and 100 mM glucose, the oxidation of glucose commences at −0.25 V and the current reaches its maximum of 310 μA/cm² at −0.05 V vs. Ag/AgCl. At the BOD-SWNT biocathode, a high potential output is achieved for the reduction of O₂ due to the direct electron transfer property of BOD at the SWNTs. In 0.10 M phosphate buffer, the electrocatalytic reduction of O₂ is observed at a high potential of 0.53 V vs. Ag/AgCl with an electrocatalytic current plateau of ca. 28 μA/cm² at 0.45 V under ambient air and ca. 102 μA/cm² under O₂-saturated atmosphere. In 0.10 M phosphate buffer containing 10 mM NAD⁺ and 40 mM glucose under O₂-saturated atmosphere, the power density of the assembled SWNT-based glucose/O₂ BFC reaches 53.9 μW/cm² at 0.50 V. The performance and the stability of the glucose/O₂ BFC are also evaluated in serum. This study could offer a new route to the development of new kinds of enzymatic BFCs with a high performance and provide useful information on future studies on the enzymatic BFCs as in vivo power sources.     

A Miniature glucose/O2 biofuel cell with single-walled carbon nanotubes-modified carbon fiber microelectrodes as the substrate

This study demonstrates a new kind of miniature glucose/O₂ biofuel cells (BFCs) based on carbon fiber microelectrodes (CFMEs) modified with single-walled carbon nanotubes (SWNTs). SWNTs are used as a support both for stably confining the electrocatalyst (i.e., methylene green, MG) for the oxidation of NADH and the anodic biocatalyst (i.e., NAD⁺-dependent glucose dehydrogenase, GDH) for the oxidation of glucose and for efficiently facilitating direct electrochemistry of the cathodic biocatalyst (i.e., laccase) for the O₂ reduction. The prepared micro-sized GDH-based bioanode and laccase-based biocathode exhibit good bioelectrocatalytic activity toward the oxidation of glucose and the reduction of oxygen, respectively. In 0.10 M phosphate buffer containing 10 mM NAD⁺ and 45 mM glucose under ambient air, the power density of the assembled miniature compartment-less glucose/O₂ BFC reaches 58 μW cm⁻² at 0.40 V. The stability of the miniature glucose/O₂ BFC is also evaluated.     

Photocurrent generated on a carotenoid-sensitized TiO2 nanocrystalline mesoporous electrode

Photocurrent was observed upon monochromatic illumination of an ITO electrode coated with a TiO₂ nanocrystalline mesoporous membrane with carotenoid 8′-apo-β-caroten-8′-oic acid (ACOA) deposited as a sensitizer (illuminated area 0.25 cm²) and immersed in an aqueous 10 mM hydroquinone (H₂Q), 0.1 M NaH₂PO₄ solution (pH = 7.4) purged with argon, using a platinum flag counter electrode (area 3.3 cm²) and a SCE reference electrode. The carotenoid-sensitized short-circuit photocurrent reached 4.6 μA/cm² upon a 40 μW/cm² incident light beam at 426 nm, with an IPCE (%, incident monochromatic photon-to-photocurrent conversion efficiency) as high as 34%. The short-circuit photocurrent was stable during 1 h of continuous illumination with only a 10% decrease. An open-circuit voltage of 0.15 V was obtained (upon 426 nm, 40 μW/cm² illumination) which remained at a constant value for hours. The observed open-circuit voltage is close to the theoretical value (0.22 V) expected in such a system. The action spectrum resembled the absorption spectrum of ACOA bound on the TiO₂ membrane with a maximum near 426 nm. No decay of the ACOA on the TiO₂ surface was observed after 12 h, presumably because of rapid regeneration of ACOA from ACOA⁺ at the surface by electron transfer from H₂Q.     

Enhancement of the performances of a single concentric glucose/O2 biofuel cell by combination of bilirubin oxidase/Nafion cathode and Au–Pt anode

This work deals with a novel preparation method of bilirubin oxidase/2,2′-azinobis-3-ethylbenzothiazoline-6-sulfonic acid electrode. The enzyme and its mediator were adsorbed on carbon Vulcan XC-72R before their immobilization into a Nafion^® matrix. Promising results were obtained when this biocathode was associated with Au₇₀Pt₃₀ nanoparticles as anode in a single concentric glucose/O₂ biofuel cell (BFC). The latter BFC delivered at 37 °C a power density of 90 μW cm^?2 for a cell voltage of 0.4 V in phosphate buffer (pH 7.4) containing 0.01 M glucose. Moreover, the electrical performances were increased with the concentration of glucose by generating up to 190 μW cm^?2 for a cell voltage of 0.52 V when the concentration of the renewable fuel reached 0.7 M.     

An easy compartment-less biofuel cell construction based on the physical co-inclusion of enzyme and mediator redox within pressed graphite discs

We report on the easy and fast immobilization of glucose oxidase (GOD) and laccase by mechanical compression with graphite particles to form disc electrodes. The electrical wiring of GOD and laccase was efficiently carried out by their co-inclusion with ferrocene (Fc) and 2,2′-azinobis (3-ethylbenzothiazoline-6-sulfonate) diammonium salt (ABTS) respectively. A glucose/air compartment-less biofuel cell was constructed based on the association of GOD-ferrocene-graphite disc and laccase-ABTS – graphite disc electrodes as bioanode and biocathode respectively. Such biofuel cell yielded a power density of 23 μW cm^?2 at 0.33 V as well as an open-circuit voltage and a short-circuit current of 0.63 V and 166 μA, respectively.     

A glucose/O2 biofuel cell base on nanographene platelet-modified electrodes

This study demonstrated a novel nanographene platelets (NGPs)-based glucose/O₂ biofuel cell (BFC) with the glucose oxidase (GOD) as the anodic biocatalysts and the laccase as the cathodic biocatalysts. The GOD/NGPs-modified electrode exhibited good catalytic activity towards glucose oxidation and the laccase/NGPs-modified electrode exhibited good catalytic activity towards O₂ electroreduction. The maximum power density was ca. 57.8 μW cm^? 2 for the assembled glucose/O₂ NGPs-based BFC. These results indicated that the NGPs were very useful for the future development of novel carbon-based nanomaterials BFC device.     

A completely spray-coated membrane electrode assembly

We present a proton exchange membrane fuel cell (PEMFC) manufacturing route, in which a thin layer of polymer electrolyte solution is spray-coated on top of gas diffusion electrodes (GDEs) to work as a proton exchange membrane. Without the need for a pre-made membrane foil, this allows inexpensive, fast, large-scale fabrication of membrane-electrode assemblies (MEAs), with a spray-coater comprising the sole manufacturing device. In this work, a catalyst layer and a membrane layer are consecutively sprayed onto a fibrous gas diffusion layer with applied microporous layer as substrate. A fuel cell is then assembled by stacking anode and cathode half-cells with the membrane layers facing each other. The resultant fuel cell with a low catalyst loading of 0.1 mg Pt/cm² on each anode and cathode side is tested with pure H₂ and O₂ supply at 80 °C cell temperature and 92% relative humidity at atmospheric pressure. The obtained peak power density is 1.29 W/cm² at a current density of 3.25 A/cm². By comparison, a lower peak power density of 0.93 W/cm² at 2.2 A/cm² is found for a Nafion NR211 catalyst coated membrane (CCM) reference, although equally thick membrane layers (approx. 25 μm), and identical catalyst layers and gas diffusion media were used. The superior performance of the fuel cell with spray-coated membrane can be explained by a decreased low frequency (mass transport) resistance, especially at high current densities, as determined by electrochemical impedance spectroscopy.     

Effective bioelectrocatalysis of bilirubin oxidase on electrochemically reduced graphene oxide

Graphene oxide (GO) was applied for construction of an effective biocathode based on bilirubin oxidase (BOD). Separation of small-sized GO sheets together with the BOD immobilisation protocol has detrimental effects on the bioelectrocatalytic reduction of oxygen. When BOD was deposited on electrochemically reduced GO (ErGO) only a negligible current density j = 2.6 μA cm^− 2 was observed. Current density dramatically increased to a value of 46 μA cm^− 2 once BOD was in-situ mixed with as-received GO directly on a glassy carbon electrode (GCE) with subsequent electrochemical reduction of the BOD/GO composite. When this protocol was tested with small-sized GO flakes separated simply using centrifugation, the fabricated biocathode exhibited j = 120 μA cm^− 2. A current density further increased to j = 280 μA cm^− 2 when BOD and purified GO were incubated ex-situ for 4 h, followed by the BOD/GO composite collection by centrifugation, its deposition on the GCE and electrochemical reduction. Moreover, oxygen reduction current increased steeply with a steady-state current density achieved at high potential (≈ 500 mV), close to the onset potential of oxygen reduction (≈ 580 mV).     

Enzymatic glucose biosensor based on flower-shaped copper oxide nanostructures composed of thin nanosheets

Well-crystallized flower-shaped copper oxide nanostructures composed of thin nanosheets has been synthesized by simple low-temperature hydrothermal process and used to fabricate highly sensitive amperometric glucose biosensor which exhibited a high and reproducible sensitivity of 47.19 μA mM^?1 cm^?2, response time less than 5 s, linear dynamic range from 0.01 to 10.0 mM, correlation coefficient of R = 0.9986, and limit of detection (LOD), based on S/N ratio (S/N = 3) of 1.37 μM. This work opens a way to utilize simply-grown CuO nanostructures as an efficient electron mediator to fabricate efficient glucose biosensors.     

Immobilization of biotinylated biomolecules onto electropolymerized poly(pyrrole-nitrilotriacetic acid)–Cu2+ film

A novel and simple immobilization strategy for biotinylated biological macromolecules onto electropolymerized poly(pyrrole-nitrilotriacetic acid)(NTA)–Cu²⁺ films without avidin as connecting bridge is reported. After complexation of Cu²⁺ by the polymerized NTA chelator, biotinylated biomolecules were immobilized by coordination of the biotin groups on the NTA–Cu²⁺ complex. The anchoring of biotinylated glucose oxidase was demonstrated by fluorescent characterization via FITC-labeled avidin and amperometric measurement of glucose. The resulting calibration curve led to a sensitivity and maximum current density values of 0.6 mA mol^?1 L cm^? 2 and 13.2 μA cm^? 2, respectively. Thus, biotinylated polyphenol oxidase was fixed leading to a catechol sensor with a sensitivity of 656 mA mol^?1 L cm^? 2 and maximum current density of 25.4 μA cm^? 2. This system was also applied to the efficient immobilization of biotinylated DNA, illustrated by impedimetric detection of the formation of the DNA duplex.     

Improved SOFC performance with continuously graded anode functional layer

Continuously graded anode functional layers (CG-AFLs) were fabricated on the Ni–YSZ anode substrates by electrophoretic co-deposition (EPD) technique. The microstructure and composition of the CG-AFLs were investigated. The result showed that uniform and graded structure in AFL was obtained. The single cells were constructed on the basis of CG-AFLs, with a maximum output power density greater than 1.10 W cm^?2 obtained at 800 °C for the cell with 9.8 μm-thick CG-AFL. Electrochemical impedance spectroscopy (EIS) indicated that the excellent cell performance was contributed to the enlargement of triple phase boundary (TPB) by adding the CG-AFL.     

Fabrication and characterization of large-size electrolyte/anode bilayer structures for low-temperature solid oxide fuel cell stack based on gadolinia-doped ceria electrolyte

Preliminary progress is reported in this communication in building a planar anode-supported low-temperature solid oxide fuel cell (SOFC) stack based on gadolinia-doped ceria (GDC) electrolyte, i.e. fabrication and characterization of a Ø80 planar bilayer structure composed of GDC electrolyte film and Ni–GDC anode substrate. The anode substrates were prepared from mixtures of NiO, GDC, and carbon black by die-pressing. After pre-firing to remove the carbon black, the anode substrates were deposited with a GDC layer using a spray coating technique. The green bilayers of anode substrate and electrolyte film were then co-sintered at 1500 °C for 3 h. Through proper control of the sintering process, bilayer structures with excellent flatness were achieved after co-sintering. Scanning electron microscopy (SEM) observation indicated that the electrolyte film was about 22 μm in thickness, highly dense, crack-free, and well-bonded to the anode substrate. Small disks which were cut out from the Ø80 bilayer structure were electrochemically examined in a single button-cell mode incorporating a (LaSr)(CoFe)O₃–GDC composite cathode. With humidified hydrogen as the fuel and air as the oxidant, the cell demonstrated an open-circuit voltage of 0.884 V and a maximum power density of 562 mW/cm² at 600 °C. The results imply that high-quality anode-supported electrolyte/anode bilayer structures were successfully fabricated. Based on them, planar anode-supported SOFC stacks will be assembled in the future.     

Development of micro-tubular SOFCs with an improved performance via nano-Ag impregnation for intermediate temperature operation

Micro-tubular solid-oxide fuel cell consisting of a 10-μm thick (ZrO₂)_0.89(Sc₂O₃)_0.1(CeO₂)_0.01 (ScSZ) electrolyte on a support NiO/(ScSZ) anode (1.8 mm diameter, 200 μm wall thickness) with a Ce_0.8Gd_0.2O_1.9 (GDC) buffer-layer and a La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ (LSCF)/GDC functional cathode has been developed for intermediate temperature operation. The functional cathode was in situ formed by impregnating the well-dispersed nano-Ag particles into the porous LSCF/GDC layer using a citrate method. The cells yielded maximum power densities of 1.06 W cm⁻² (1.43 A cm⁻², 0.74 V), 0.98 W cm⁻² (1.78 A cm⁻², 0.55 V) and 0.49 W cm⁻² (1.44 A cm⁻², 0.34 V), at 650, 600 and 550 °C, respectively.     

Comparison of performances of bioanodes modified with graphene oxide and graphene–platinum hybrid nanoparticles

The performances of graphene oxide (GO) and graphene–platinum hybrid nanoparticles (Gr-Pt hybrid NPs) were compared for biofuel cell (BFC) systems. This is the first study that constitutes these nanomaterials in BFC systems. For this purpose, fabricated bioanodes were combined with laccase modified biocathode in a single cell membraneless BFC. Power and current densities of these systems were calculated as 2.40 μW cm^− 2 and 211.90 μA cm^− 2 for GO based BFC and 4.88 μW cm^− 2 and 246.82 μA cm^− 2, for Gr-Pt hybrid NPs based BFC. As a result, a pioneer study which demonstrates the effective performances of combination of graphene with Pt was conducted.     

MgO polyhedral nanocages and nanocrystals based glucose biosensor

MgO polyhedral nanocages and nanocrystals, synthesized by non-catalytic simple thermal evaporation process, were used to fabricate high-sensitive amperometric glucose biosensor which showed a high and reproducible sensitivity of 31.6 μA μM^?1 cm^?2 with a response time less than 5 s, linear dynamic range from 1.0 to 9.0 μM and correlation coefficient of R = 0.9993. The detection limit of fabricated biosensor (based on S/N ratio = 3) was estimated to be 68.3 ± 0.02 nM. To the best of our knowledge, this is the first report which demonstrates the use of MgO nanostructures for the fabrication of glucose biosensor; hence, this work opens a new way to utilize MgO nanostructures as an efficient electron mediator to fabricate efficient glucose biosensors.     

Evaluation of tungsten–rhodium coating on an integrated platform as a permanent chemical modifier for cadmium,lead, and selenium determination by electrothermal atomic absorption spectrometry

A tungsten–rhodium coating on the integrated platform of a transversely heated graphite atomizer is proposed as a permanent chemical modifier for the determination of Cd, Pb, and Se by electrothermal atomic absorption spectrometry. It was demonstrated that coating with 250 μg W+200 μg Rh is as efficient as the conventional Mg(NO₃)₂+NH₄H₂PO₄ or Pd+Mg(NO₃)₂ modifiers for avoiding most serious interferences. The permanent W–Rh modifier remains stable for 300–350 firings of the furnace, and increases tube lifetime by 50%–100% when compared to pyrolytic carbon integrated platforms. Also, there is less degradation of sensitivity during the atomizer lifetime when compared with the conventional modifiers, resulting in a decreased need of re-calibration during routine analysis. The characteristic masses and detection limits achieved using the permanent modifier were respectively: Cd 1.1±0.4 pg and 0.020 μgL⁻¹; Pb 30±3 pg and 0.58 μgL⁻¹ and Se 42±5 pg and 0.64μgL⁻¹. Results from the determination of these elements in water reference materials were in agreement with the certified values, since no statistical differences were found by the paired t-test at the 95% level.     

Asymmetric electrochemical capacitor microdevice designed with vanadium nitride and nickel oxide thin film electrodes

Vanadium nitride thin film has been coupled with electrodeposited nickel oxide in order to design an electrochemical capacitor microdevice. VN has been used as negative electrode while NiO was used as the positive one in 1 M KOH electrolyte. VN exhibits a pseudo-capacitive behavior while NiO shows a faradaic behavior. This asymmetric microdevice has been operated between 0.5 and up to 1.8 V in aqueous based electrolyte (1 M KOH). Long term cycling ability (10,000 charge/discharge cycles) has been demonstrated with interesting energy (1.0 μW h cm^− 2) and power (40 mW cm^− 2) densities.     

Electrochemical performances of LaBaCuFeO5+x and LaBaCuCoO5+x as potential cathode materials for intermediate-temperature solid oxide fuel cells

Layered perovskite-structure oxides LaBaCuFeO_5+x (LBCFO) and LaBaCuCoO_5+x (LBCCO) were prepared and the electrical conductivity and electrochemical performance were investigated as potential cathode materials for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The electrical conductivity of LBCCO is much higher than that of LBCFO. Area specific resistances of LBCFO and LBCCO cathode materials on Ce_0.8Sm_0.2O_1.9 (SDC) electrolyte are as low as 0.21 Ω cm² and 0.11 Ω cm² at 700 °C, respectively. The maximum power density of the LBCFO/SDC/Ni-SDC and LBCCO/SDC/Ni-SDC cells with 300 μm thick electrolytes attains 557 mW cm^?2 and 603 mW cm^?2 at 800 ^oC, respectively. Preliminary results demonstrated that the layered perovskite-structure oxides LBCFO and LBCCO are very promising cathode materials for application in IT-SOFCs.     

A study on solution deposited CuSCN thin films: Structural,electrochemical, optical properties

A cost-effective successive ionic layer adsorption and reaction (SILAR) method was used to deposit copper (I) thiocyanate (CuSCN) thin films on glass and steel substrates for this study. The deposited thin films were characterized for their structural, morphological, optical and electrochemical properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), UV–visible spectroscopy and VersaSTAT potentiostat. A direct band gap of 3.88 eV and 3.6 eV with film thickness of 0.7 μm and 0.9 μm was obtained at 20 and 30 deposition cycles respectively. The band gap, microstrain, dislocation density and crystal size were observed to be thickness dependent. The specific capacitance of the CuSCN thin film electrode at 20 mV/s was 760 F g⁻¹ for deposition 20 cycles and 729 F g⁻¹ for deposition 30 cycles.