Immobilization of biotinylated biomolecules onto electropolymerized poly(pyrrole-nitrilotriacetic acid)–Cu2+ film

A novel and simple immobilization strategy for biotinylated biological macromolecules onto electropolymerized poly(pyrrole-nitrilotriacetic acid)(NTA)–Cu²⁺ films without avidin as connecting bridge is reported. After complexation of Cu²⁺ by the polymerized NTA chelator, biotinylated biomolecules were immobilized by coordination of the biotin groups on the NTA–Cu²⁺ complex. The anchoring of biotinylated glucose oxidase was demonstrated by fluorescent characterization via FITC-labeled avidin and amperometric measurement of glucose. The resulting calibration curve led to a sensitivity and maximum current density values of 0.6 mA mol^?1 L cm^? 2 and 13.2 μA cm^? 2, respectively. Thus, biotinylated polyphenol oxidase was fixed leading to a catechol sensor with a sensitivity of 656 mA mol^?1 L cm^? 2 and maximum current density of 25.4 μA cm^? 2. This system was also applied to the efficient immobilization of biotinylated DNA, illustrated by impedimetric detection of the formation of the DNA duplex.     

Enzymatic glucose biosensor based on flower-shaped copper oxide nanostructures composed of thin nanosheets

Well-crystallized flower-shaped copper oxide nanostructures composed of thin nanosheets has been synthesized by simple low-temperature hydrothermal process and used to fabricate highly sensitive amperometric glucose biosensor which exhibited a high and reproducible sensitivity of 47.19 μA mM^?1 cm^?2, response time less than 5 s, linear dynamic range from 0.01 to 10.0 mM, correlation coefficient of R = 0.9986, and limit of detection (LOD), based on S/N ratio (S/N = 3) of 1.37 μM. This work opens a way to utilize simply-grown CuO nanostructures as an efficient electron mediator to fabricate efficient glucose biosensors.     

Porous cuprous oxide microcubes for non-enzymatic amperometric hydrogen peroxide and glucose sensing

Using porous cuprous oxide (Cu₂O) microcubes, a simple non-enzymatic amperometric sensor for the detection of H₂O₂ and glucose has been fabricated. Cyclic voltammetry (CV) revealed that porous Cu₂O microcubes exhibited a direct electrocatalytic activity for the reduction of H₂O₂ in phosphate buffer solution and the oxidation of glucose in an alkaline medium. The non-enzymatic amperometric sensor used in the detection of H₂O₂ with detection limit of 1.5 × 10^?6 M over wide linear detection ranges up to 1.5 mM and with a high sensitivity of 50.6 μA/mM. This non-enzymatic voltammetric sensor was further utilized in detection of glucose with a detection limit of 8.0 × 10^?7 M, a linear detection range up to 500 μM and with a sensitivity of ?70.8 μA/mM.     

MgO polyhedral nanocages and nanocrystals based glucose biosensor

MgO polyhedral nanocages and nanocrystals, synthesized by non-catalytic simple thermal evaporation process, were used to fabricate high-sensitive amperometric glucose biosensor which showed a high and reproducible sensitivity of 31.6 μA μM^?1 cm^?2 with a response time less than 5 s, linear dynamic range from 1.0 to 9.0 μM and correlation coefficient of R = 0.9993. The detection limit of fabricated biosensor (based on S/N ratio = 3) was estimated to be 68.3 ± 0.02 nM. To the best of our knowledge, this is the first report which demonstrates the use of MgO nanostructures for the fabrication of glucose biosensor; hence, this work opens a new way to utilize MgO nanostructures as an efficient electron mediator to fabricate efficient glucose biosensors.     

Enhancement of the performances of a single concentric glucose/O2 biofuel cell by combination of bilirubin oxidase/Nafion cathode and Au–Pt anode

This work deals with a novel preparation method of bilirubin oxidase/2,2′-azinobis-3-ethylbenzothiazoline-6-sulfonic acid electrode. The enzyme and its mediator were adsorbed on carbon Vulcan XC-72R before their immobilization into a Nafion^® matrix. Promising results were obtained when this biocathode was associated with Au₇₀Pt₃₀ nanoparticles as anode in a single concentric glucose/O₂ biofuel cell (BFC). The latter BFC delivered at 37 °C a power density of 90 μW cm^?2 for a cell voltage of 0.4 V in phosphate buffer (pH 7.4) containing 0.01 M glucose. Moreover, the electrical performances were increased with the concentration of glucose by generating up to 190 μW cm^?2 for a cell voltage of 0.52 V when the concentration of the renewable fuel reached 0.7 M.     

Polyaniline nanotubes for impedimetric triglyceride detection

Polyaniline nanotubes (PANI-NT) based film electrophoretically deposited onto indium–tin–oxide (ITO) coated glass plate has been utilized for covalent immobilization of lipase (LIP), via glutaraldehyde (Glu), for triglyceride detection using impedimetric technique. It is shown that fatty acid molecules produced during triglyceride hydrolysis result in change in charge transfer resistance (R_CT) of PANI-NT film with varying triglyceride concentration. LIP/Glu/PANI-NT/ITO bioelectrode has linearity as 25–300 mg dL^?1, sensitivity as 2.59 × 10^?3 KΩ^?1 mg^?1 dL, response time as 20 s and regression coefficient as 0.99. A low value of apparent Michaelis–Menten constant (～0.62 mM) indicates high enzyme affinity to tributyrin. The LIP/Glu/PANI-NT/ITO bioelectrode has been utilized to estimate triglyceride in serum samples.     

Novel luminescent nanoparticles for DNA detection

Highly luminescent LaF₃:Ce³⁺/Tb³⁺ nanocrystals were successfully prepared and surface functionalized via Layer-by-Layer technology. These as-prepared nanocrystals are highly resistant to photobleaching and pretty dispersible in aqueous solution. Due to the efficient luminescence quenching of the nanocrystals by nucleic acids, a facile fluorescence quenching method was developed for the detection of trace amount of nucleic acids. Under optimal conditions, the fluorescence intensity was proportional to the DNA concentration over the range of 0.60–25.0 μg mL^?1 for calf thymus DNA (ct-DNA) and 0.60–30.0 μg mL^?1 for herring sperm DNA (hs-DNA), respectively. The corresponding detection limit is 0.21 μg mL^?1 for ct-DNA and 0.31 μg mL^?1 for hs-DNA, respectively. The results indicated that the reported method is simple and rapid with wide linear range. Also, the recovery and relative standard deviation of this method are reasonable and satisfactory.     

Nonenzymatic glucose fuel cells with an anion exchange membrane as an electrolyte

Nonenzymatic glucose fuel cells were prepared by using a polymer electrolyte membrane and Pt-based metal catalysts. A fuel cell with a cation exchange membrane (CEM), which is often used for conventional polymer electrolyte fuel cells, shows an open circuit voltage (OCV) of 0.86 V and a maximum power density (P_max) of 1.5 mW cm^?2 with 0.5 M d-glucose and humidified O₂ at room temperature. The performance significantly increased to show an OCV of 0.97 V and P_max of 20 mW cm^?2 with 0.5 M d-glucose in 0.5 M KOH solution when the electrolyte membrane was changed from a CEM to an anion exchange membrane (AEM). This is due to the superior catalytic activity for both glucose oxidation and oxygen reduction in alkaline medium than in acidic medium. The anodic reaction of the fuel cell can be estimated to be the oxidation of glucose to gluconic acid via a two-electron process under these experimental conditions. The crossover of glucose through an electrolyte membrane was negligibly small compared with methanol and may not represent a serious technical problem due to the cross-reaction.     

Structural characterization of dodecyltrimethylammonium (DTMA) bromide modified sepiolite and its adsorption isotherm studies

In this study, dodecyltrimethylammonium (DTMA) bromide was used to modify natural sepiolite via an ion exchange reaction to form DTMA-sepiolite. Sepiolite and DTMA-sepiolite were then characterized by using Brunauer–Emmett–Teller (BET), elemental analysis, XRD, FT-IR, thermogravimetric (TG) and zeta potential analysis techniques. The BET surface area of sepiolite significantly decreased from 152.14 m² g^–1 to 88.63 m² g^–1, after the modification, due to the coverage of the pores of sepiolite. DTMA was located onto sepiolite according to the differential thermogravimetric (dTG) peaks of DTMA-sepiolite. XRD results confirmed the interaction between DTMA⁺ cations and sepiolite. FT-IR spectra indicated the existence of DTMA functional groups on sepiolite surface. After the characterization was accomplished, adsorption isotherm studies of naphthalene, which is the first member of the polycyclic aromatic hydrocarbons (PAHs), were carried out. The maximum adsorption capacity of DTMA-sepiolite for naphthalene was determined from Langmuir isotherm equation at pH 6 and 20 °C as 1.88 × 10^–4 mol g^?1 or 24.09 mg g^?1.     

Electrochemical determination of rosiglitazone by square-wave adsorptive stripping voltammetry method

Square-wave adsorptive stripping voltammetry technique was used to determine rosiglitazone (ROS) on the hanging mercury dropping electrode (HMDE) surface, in Britton Robinson buffer, pH = 5. The voltammetric cathodic peak was observed at ?1520 mV vs. Ag/AgCl reference electrode. The voltammetric peak response was characterized with respect to pH, supporting electrolyte, accumulation potential, preconcentration time, scan rate, frequency, pulse amplitude, surface area of the working electrode and the convection rate. Under optimal conditions, the voltammetric current is proportional to the concentration of ROS over the concentration range of 5 × 10^?8–8 × 10^?7 mol l^?1 (r = 0.9899) with a detection limit of 3.2 × 10^?11 mol l^?1 using 120 s accumulation time. The developed SW-AdSV procedure showed a good reproducibility, the relative standard deviation RSD% (n = 10) at a concentration level of 5 × 10^?7 mol l^?1 was 0.33%, whereas the accuracy was 101% ± 1.0. The proposed method was successfully applied to assay the drug in the human urine and plasma samples with mean recoveries of 90 ± 0.71% and 86 ± 1.0%, respectively.     

A glucose/O2 biofuel cell base on nanographene platelet-modified electrodes

This study demonstrated a novel nanographene platelets (NGPs)-based glucose/O₂ biofuel cell (BFC) with the glucose oxidase (GOD) as the anodic biocatalysts and the laccase as the cathodic biocatalysts. The GOD/NGPs-modified electrode exhibited good catalytic activity towards glucose oxidation and the laccase/NGPs-modified electrode exhibited good catalytic activity towards O₂ electroreduction. The maximum power density was ca. 57.8 μW cm^? 2 for the assembled glucose/O₂ NGPs-based BFC. These results indicated that the NGPs were very useful for the future development of novel carbon-based nanomaterials BFC device.     

Poly(3,4-ethylene-dioxythiophene) electrode for the selective determination of dopamine in presence of sodium dodecyl sulfate

A novel biosensor using poly(3,4-ethylene dioxythiophene) (PEDOT) modified Pt electrode was developed for selective determination of dopamine (DA) in presence of high concentrations of ascorbic acid (AA) and uric acid (UA) with a maximum molar ratio of 1/1000, and 1/100 in the presence of sodium dodecyl sulfate (SDS). SDS forms a monolayer on PEDOT surface with a high density of negatively charged end directed outside the electrode. The electrochemical response of dopamine was improved by SDS due to the enhanced accumulation of protonated dopamine via electrostatic interactions. The common overlapped oxidation peaks of AA, UA and DA can be resolved by using SDS as the DA current signal increases while the corresponding signals for AA and UA are quenched. The use of SDS in the electrochemical determination of dopamine using linear sweep voltammetry at modified electrode PEDOT/Pt resulted in detecting dopamine at relatively lower concentrations. The DA concentration could be measured in the linear range of 0.5 to 25 μmol L^? 1 and 30 μmol L^? 1 to 0.1 mmol L^? 1 with correlation coefficients of 0.998 and 0.993 and detection limits 61 nmol L^? 1 and 86 nmol L^? 1, respectively. The validity of using this method in the determination of dopamine in human urine was also demonstrated.     

Nanoplates and nanostars of β-PbO formed at the air/water interface

Nanoparticles with different shapes were prepared at the air/water interface via hydrolysis of Pb²⁺ ions under Langmuir films of poly(N-vinylcarbazole) (PVK) at 30–50 °C. It was found that round or irregular nanoparticles with the size of several to several tens of nanometers were formed when the PbCl₂ aqueous solution with the concentration of 1 × 10^?3 mol L^?1 was used as subphase, while single-crystalline quasi-hexagonal nanoplates, nanostars and dendrites with the size of several hundreds of nanometers were obtained when the subphase concentration was 1 × 10^?4 mol L^?1. Analysis on the selective-area electron diffraction (SAED) patterns revealed that the formed nanoparticles are β-PbO. The formation of the nanostructures should be attributed to the formation and dehydration of lead hydroxide, diffuse-limited growth and aggregation of nanoparticles at the air/water interface.     

Development of a solid phase extraction method for the multielement determination of trace metals in natural waters including sea-water by FI-ICP-MS

An automated solid phase extraction method by flow analysis on-line inductively coupled plasma mass spectrometry (FI-ICP-MS) for the determination of cobalt, chromium, nickel, cadmium, manganese, zinc, copper and lead in sea-water and other natural waters is described. The system is based on retention of the analytes onto a minicolumn packed with a chelating resin, 1,5-bis (2-pyridyl)-3-sulphophenyl methylene thiocarbonohydrazide immobilized on aminopropyl-controlled pore glass, placed in the injection valve of a simple flow manifold. The effects of chemical and flow variables were investigated and selected as a compromise between sensitivity and sampling frequency. So, the sample solutions (adjusted to pH 8.0 ± 0.5) were passed through the column. After washing the column with water, the adsorbed metals were subsequently eluted into the plasma with 4% m/m nitric acid. Detection limits of the trace metals (180 s sample loading time at a sample flow rate of 0.7 mL min^? 1; sampling frequency 8.6 h^? 1) were 0.002 μg L^? 1 for Co, 0.057 μg L^? 1 for Cr, 0.117 μg L^? 1 for Ni, 0.004 μg L^? 1 for Cd, 0.210 μg L^? 1 for Mn, 0.260 μg L^? 1 for Zn, 0.030 μg L^? 1 for Cu and 0.020 μg L^? 1 for Pb, with enrichment factors between 2.2 and 6.8. The accuracy of the proposed method was checked with certified reference materials (CRMs) of sea-water SLEW 3, LGC6016 and CASS-5, river water SLRS-5 and fortified lake water TMDA-54.4. The results from the determination of these metals were in agreement with the certified values and recovery values ranged between 92.2 and 110.6%. The method was applied to the determination of these metal ions in sea-water samples collected in the Málaga Bay in order to realize a pilot study necessary to generate preliminary information on which to base a more detailed pollution study by heavy metals of the Bay.     

Enhancement of electrochemical performance and thermal compatibility of GdBaCo2/3Fe2/3Cu2/3O5+δ cathode on Ce1.9Gd0.1O1.95 electrolyte for IT-SOFCs

Transition-metal doped double-perovskite structure oxides GdBaCo_2/3Fe_2/3Ni_2/3O_5+δ (FN-GBCO), GdBaCo_2/3Fe_2/3Cu_2/3O_5+δ (FC-GBCO), GdBaCoCuO_5+δ (C-GBCO) and pristine GdBaCo₂O_5+δ (GBCO) were synthesized via a citrate combustion method. The thermal-expansion coefficient (TEC) and electrochemical performance of the oxides were investigated as potential cathodes for intermediate-temperature solid oxide fuel cells (IT-SOFCs). The TEC exhibited by the FC-GBCO cathode up to 900 °C is 14.6 × 10^?6 °C^?1, which is lower than the value of GBCO (19.9 × 10^?6 °C^?1). Area specific resistances (ASR) of 0.165 Ω cm² at 700 °C and 0.048 Ω cm² at 750 °C were achieved for the FC-GBCO cathode on a Ce_0.9Gd_0.1O_1.95 (CGO) electrolyte. An electrolyte supported (300 μm thick) single-cell configuration of FC-GBCO/CGO/Ni-CGO attained a maximum power density of 435 mW cm^?2 at 700 °C. The unique composition of GBCO co-doped with Fe and Cu ions in the Co sites exhibited reduced TEC and enhancement of electrochemical performance and good chemical compatibility with CGO, and this composition is proving to be a potential cathode for IT-SOFCs.     

The determination of trace lead in drinking water by flow injection spectrophotometry

Lead is the non-essential trace element in the human body, and it has been confirmed that drinking water is one of the sources of lead in human body. In the research, based on the sensitive colour reaction of lead with I^?–EV⁺–PVA, a simple, sensitive, accurate and portable method for the determination of trace lead in drinking waters was proposed. Chemicals and physicals had been optimized in detail. The apparent molar absorption coefficient was up to 7.4 × 10⁵ mol L^?1 cm^?1. The developed method provided a linearity range over 5–80 μg L^?1. The regression deviation was between 0.71% and 2.33%. The 3σ detection limit was 0.9 μg L^?1. Close to the quantitation limit for the analyte the relative standard deviation was 1.10% (n = 10) at 40 μg L^?1. The method developed here for analysis of lead yielded results that were comparable with those of the GFAAS.     

A high-performance carbon derived from polyaniline for supercapacitors

Activated carbon derived from rod-shaped polyaniline (the diameter of 170 nm) was synthesized by carbonization and subsequent activation with KOH. The obtained activated carbon exhibits a high specific capacitance (455 F g^?1) and remarkable rate capability due to its high specific surface area (1976 m² g^?1), narrow pore size distribution (< 3 nm) as well as short diffusion length. It is indicated that the promising synthetic method used in this work can pave the way for designing new carbon based materials from different polymers for high-performance energy applications.     

Ultrasensitive determination of serum albumin using resonance light scattering based on ZnS-polyacrylic acid nanoparticles

ZnS-polyacrylic acid (ZnS-PAA) was prepared by an in situ polymerization method using nano-ZnS as core in the presence of acrylic acid (AA), and ZnS-PAA nanoparticles was characterized by ultraviolet spectrometry (UV) and transmission electron microscopy (TEM). Based on the significant increase of the resonance light scattering (RLS) intensity with the interaction between nanoparticles and serum albumin, RLS method was developed for the sensitive determination of serum albumin (BSA and HSA). Under optimum conditions, the change of the intensity (ΔI) of the RLS spectra at λ = 392 nm was linearly proportional to the concentration of BSA and HSA. The linear range was 1–100 ng mL^?1 for HSA and 1–120 ng mL^?1 for BSA, and the limit of detection (LOD) was 0.4 ng mL^?1 for HSA and 0.5 ng mL^?1 for BSA. This method proved to be very sensitive, rapid, simple and tolerant of most interfering substances.     

Flow-injection chemiluminescence determination of dihydralazine sulfate in serum using luminol and diperiodatocuprate (III) system

A novel flow-injection chemiluminescence (CL) method for the determination of dihydralazine sulfate (DHZS) is described. The method is based on the reaction of luminol and diperiodatocuprate (K₂[Cu(H₂IO₆)(OH)₂], DPC) in alkaline medium to emit CL, which is greatly enhanced by DHZS. The possible CL mechanism was first proposed based on the kinetic characteristic, CL spectrum and UV spectra. The optimum condition for the CL reaction was in detail studied using flow-injection system. The experiments indicated that under optimum condition, the CL intensity was linearly related to the concentration of DHZS in the range of 7.0 × 10^?9 to 8.6 × 10^?7 g mL^?1 with a detection limit (3σ) of 2.1 × 10^?9 g mL^?1. The proposed method had good reproducibility with the relative standard deviation 3.1% (n = 7) for 5.2 × 10^?8 g mL^?1 of DHZS. This method has the advantages of simple operation, fast response and high sensitivity. The special advantage of the system is that very low concentration of luminol can react with DPC catalyzed by DHZS to get excellent experiment results. And CL cannot be observed nearly when luminol with same concentration reacts with other oxidants, so luminol–DPC system has higher selectivity than other luminol CL systems. The method has been successfully applied to determine DHZS in serum.     

Synthesis of mesoporous hollow carbon hemispheres as highly efficient Pd electrocatalyst support for ethanol oxidation

The synthesis procedure of the highly mesoporous hollow carbon hemispheres (HCHs) using glucose as carbon source and solid core mesoporous shell silica (SCMSS) as template and the formation mechanism of the HCHs have been presented. The HCHs show an ultrahigh surface area of 1095.59 m² g^?1 and an average mesopore size of 9.38 nm. The hemispherical structure with large mesopores also results in the improvement in the mass transfer and therefore more concentrated ethanol solution can be used to increase the energy density. The additional advantage of the HCHs compared to the hollow carbon spheres is that they can provide the similar surface area at reduced volume. The current densities of ethanol oxidation on Pd nanoparticles supported on HCH (Pd/HCH) electrocatalyst are three times as many as on Pd/C at the same Pd loadings.