Phase separation and crystallinity in proton conducting membranes of styrene grafted and sulfonated poly(vinylidene fluoride)

A series of proton exchange membranes have been prepared by the preirradiation grafting method. Styrene was grafted onto a matrix of poly(vinylidene fluoride) (PVDF) after electron beam irradiation. Part of the samples was crosslinked with divinylbenzene (DVB) or bis(vinylphenyl)ethane (BVPE). Subsequent sulfonation gave membranes grafted with poly(styrene sulfonic acid) and marked PVDF‐g‐PSSA. It was found that the intrinsic crystallinity of the matrix decreased in both the grafting and the sulfonation reaction in all the membranes. The graft penetration and the ion conductivity are influenced strongly by the crosslinker. The ion conductivity is considerably lower in crosslinked membranes than in noncrosslinked ones. Generally, the mechanical strength decreases with crosslinking. The membranes show a regular phase separated structure in which the sulfonated grafts are incorporated in the amorphous parts of the matrix polymer. The phase separated domains are small, of the order of magnitude of 100–250 nm. These were resolved on transmission electron micrographs and on atomic force images but could not be resolved with microprobe Raman spectroscopy. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1741–1753, 1999     

Radiation-grafted proton exchange membranes based on co-grafting from binary monomer mixtures into poly(ethylene-co-tetrafluoroethylene) (ETFE) film

In this study, proton exchange membranes (PEMs) based on a poly(ethylene-co-tetrafluoroethylene) (ETFE) film were synthesized through the graft copolymerization of styrene and VTMS (vinyltrimethoxysilane), or styrene and TMSPM (3-(trimethoxysilyl) propyl methacrylate) binary monomer systems using a simultaneous irradiation method. The prepared membranes with the similar degrees of grafting were investigated by measuring ion exchange capacity, proton conductivity, water uptake, chemical stability, and dimensional stability. The results indicate that the silane-crosslinked proton exchange membrane (PEM) has not only lower water uptake and dimensional change but also high proton conductivity at low humidity condition compared to non-crosslinked poly(ethylene-co-tetrafluoroethylene)-g-poly(styrene sulfonic acid) (ETFE-g-PSSA). Also, the chemical stability of silane-crosslinked fuel cell membranes was more improved than that of non-crosslinked fuel cell membrane.     

Thermal degradation behaviour of radiation grafted FEP-g-polystyrene sulfonic acid membranes

The thermal degradation behaviour and the gaseous products of FEP-g-polystyrene sulfonic acid membranes prepared by radiation-induced grafting of styrene onto poly(tetrafluoroethylene-co-hexafluoropropylene) (FEP) films and the subsequent sulfonation were studied using thermal gravimetric analysis coupled with Fourier transform infrared spectrometry (TGA/FTIR). The membranes were found to have a three-step degradation behaviour due to water removal, elimination of sulfonic acid groups and decomposition of the FEP matrix. The evolving gaseous products were identified using FTIR analysis. The degree of grafting was found to have a strong effect on the weight loss in the membranes, whilst the degradation temperatures of the individual membrane components were shown to be independent of the degree of grafting.     

Water-swollen cation-exchange membranes prepared using poly(vinyl alcohol) (PVA)/poly(styrene sulfonic acid-co-maleic acid) (PSSA-MA)

A water-swollen type of poly(vinyl alcohol) (PVA)/poly(styrene sulfonic acid-co-maleic acid) (PSSA-MA) cation-exchange membrane was prepared and characterized in terms of its electrochemical properties including ion-exchange capacity (IEC), electrical resistance, and transport number, etc. PVA/PSSA-MA membranes exhibited low electrical resistance and highly swelling property. In spite of 2–4 times higher water swelling ratio (WSR) than that of CMX (Tokuyama Corp., Japan), the transport number of the prepared membrane was comparable to that of the commercial membrane (t_n>0.93). Moreover, the electric resistance of PVA/PSSA-MA membrane was measured as low as 1.0–1.5 Ω cm². Further, in this study, interrelation between the membrane characteristics and crosslinking was investigated, and the result exhibited that the crosslinking degree is one of major factors affecting the ion transport through a water-swollen ion-exchange membrane (IEM).     

Ion-specific swelling of poly(styrene sulfonic acid) hydrogel

Poly(styrene sulfonic acid) (PSSA) hydrogel was prepared by radiation crosslinking using methyl N,N-bis-acrylamide as crosslinker. Effects of ion species and concentration on the swelling behavior of PSSA hydrogel were investigated in aqueous solution of selected anions (F-, Cl-, Br-, SCN-), cations (Li+, Na+, K+, Ca2+), and hydrophobic ions (tetramethylammonium cation TMA+, tetrabutylammonium cation TBA+, and dodecyltrimethylammonium cation TAB+). The deswelling extent of PSSA hydrogel follows anion Hofmeister series, i.e., SCN- < Br- < Cl- < F-, in solutions containing selected anions and K+ as counterion up to a concentration of 2 mol.L(-1). On the contrary, the deswelling extent of PSSA hydrogel in solutions containing selected cations and Cl- follows the sequence of Li+ < Na+ < K+ < Ca2+, which is the reverse of the Hofmeister series except Ca2+. We have discussed the effects of ions on the hydrogen bonding through SO3- and phenyl ring in salt solutions at low and high concentrations. Other interactions, such as the cation-pi and hydrophobic interactions, also contributed to the ion-specific swelling of PSSA hydrogel. The proposed mechanism was further elucidated by FTIR and NMR analysis. A very specific deswelling-reswelling phenomenon of PSSA hydrogel in KF solution has been observed and ascribed to the F- binding to phenyl ring through a specific interaction.     

Radiation grafted poly(vinylidene fluoride)-graft-polystyrene sulfonic acid membranes for fuel cells: Structure-property relationships

<正>Structure-property relationships for poly(vinylidene fluoride)-graft-polystyrene sulfonic acid(PVDF-g-PSSA) fuel cell membranes prepared by a single step method involving radiation-induced grafting of sodium styrene sulfonate(SSS) onto electron beam(EB) irradiated poly(vinylidene fluoride)(PVDF) films were established.The physico-chemical properties of the membranes such as ion exchange capacity,water swelling and proton conductivity were correlated with the degree of grafting(G,%) and the structural changes taking place in the membrane matrix during the preparation procedure. The variation in the crystallinity and the thermal stability of membranes was studied by differential scanning calorimetry (DSC) and thermogravimetric analysis(TGA),respectively.The membranes were found to undergo substantial structural changes in forms of ionic sites increase,hydrophilicity enhancement,hydrophobicity reduction and crystallinity decrease with the variation in G(%) and the preparation method.The structural and thermal properties of the obtained membranes were also compared with their counterparts prepared by a conventional two-steps method i.e.radiation induced grafting of styrene onto EB irradiated PVDF films followed by sulfonation.The PVDF-g-PSSA membranes obtained by a single-step method were found to have superior properties compared to those obtained by the conventional two-steps method.     

Synthesis and characterization of grafted/crosslinked proton conducting membranes based on amphiphilic PVDF copolymer

A novel graft copolymer consisting of a poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) backbone and poly(glycidyl methacrylate) side chains, that is, P(VDF‐co‐CTFE)‐g‐PGMA, was synthesized through atom transfer radical polymerization (ATRP) using CTFE units as a macroinitiator. Successful synthesis and microphase‐separated structure of the polymer were confirmed by ¹H NMR, FTIR spectroscopy, and TEM. As‐synthesized P(VDF‐co‐CTFE)‐g‐PGMA copolymer was sulfonated by sodium bisulfite, followed by thermal crosslinking with sulfosuccinic acid (SA) via the esterification to produce grafted/crosslinked polymer electrolyte membranes. The IEC values continuously increased with increasing SA content but water uptake increased with SA content up to 10 wt %, above which it decreased again as a result of competitive effect between crosslinking and hydrophilicity of membranes. At 20 wt % of SA content, the proton conductivity reached 0.057 and 0.11 S/cm at 20 and 80 °C, respectively. The grafted/crosslinked P(VDF‐co‐CTFE)‐g‐PGMA/SA membranes exhibited good mechanical properties (>400 MPa of Young's modulus) and high thermal stability (up to 300 °C), as determined by a universal testing machine (UTM) and TGA, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1110–1117, 2010     

Nanofiltration membranes based on poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)‐graft‐poly(styrene sulfonic acid)

Graft copolymers comprising poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) backbone and poly(styrene sulfonic acid) side chains, i.e. P(VDF‐co‐CTFE)‐g‐PSSA were synthesized using atom transfer radical polymerization (ATRP) for composite nanofiltration (NF) membranes. Direct initiation of the secondary chlorinated site of CTFE units facilitates grafting of PSSA, as revealed by FT‐IR spectroscopy. The successful “grafting from” method and the microphase‐separated structure of the graft copolymer were confirmed by transmission electron microscopy (TEM). Wide angle X‐ray scattering (WAXS) also showed the decrease in the crystallinity of P(VDF‐co‐CTFE) upon graft copolymerization. Composite NF membranes were prepared from P(VDF‐co‐CTFE)‐g‐PSSA as a top layer coated onto P(VDF‐co‐CTFE) ultrafiltration support membrane. Both the rejections and the flux of composite membranes increased with increasing PSSA concentration due to the increase in SO₃H groups and membrane hydrophilicity, as supported by contact angle measurement. The rejections of NF membranes containing 47 wt% of PSSA were 83% for Na₂SO₄ and 28% for NaCl, and the solution flux were 18 and 32 L/m² hr, respectively, at 0.3 MPa pressure. Copyright © 2008 John Wiley & Sons, Ltd.     

Highly proton conducting proton‐exchange membranes based on fluorinated poly(arylene ether ketone)s with octasulfonated segments

A new bisphenol monomer containing a pair of electron‐rich tetra‐arylmethane units was designed and synthesized. Based on this monomer, along with commercial 4,4′‐(hexafluoroisopropylidene)diphenol A and 4,4′‐difluorobenzophenone, a series of novel poly(arylene ether ketone)s containing octasulfonated segments of varying molar percentage (x) (6F‐SPAEK‐x) were successfully synthesized by polycondensation reactions, followed by sulfonation. Tough, flexible, and transparent membranes, exhibiting excellent thermal stabilities and mechanical properties were obtained by casting. 6F‐SPAEK‐x samples exhibited appropriate water uptake and swelling ratios at moderate ion exchange capacities (IECs) and excellent proton conductivities. The highest proton conductivity (215 mS cm⁻¹) is observed for hydrated 6F‐SPAEK‐15 (IEC = 1.68 meq g⁻¹) at 100 °C, which is more than 1.5 times that of Nafion 117. Furthermore, the 6F‐SPAEK‐10 membrane exhibited comparable proton conductivity (102 mS cm⁻¹) to that of Nafion 117 at 80 °C, with a relatively low IEC value (1.26 meq g⁻¹). Even under 30% relative humidity, the 6F‐SPAEK‐20 membrane (2.06 meq g⁻¹) showed adequate conductivity (2.1 mS cm⁻¹) compared with Nafion 117 (3.4 mS cm⁻¹). The excellent comprehensive properties of these membranes are attributed to well‐defined nanophase‐separated structures promoted by strong polarity differences between highly ionized and fluorinated hydrophobic segments. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 25–37     

Investigation of the doping efficiency of poly(styrene sulfonic acid) in poly(3,4‐ethylenedioxythiophene)/poly(styrene sulfonic acid) dispersions by capillary electrophoresis

CE can efficiently separate poly(3,4‐ethylenedioxythiophene)/poly(styrene sulfonic acid) (PEDOT/PSS) complexes and free PSS in dispersions and can be used to estimate the degree of PSS doping. We investigated the doping efficiency of PSS on PEDOT in dispersions using CE and its effect on the conductivity of the resulting PEDOT/PSS films. Results of this study indicate that dispersions containing 1:2.5–3 EDOT:PSS feed ratio (by weight) exhibiting 72–73% PSS doping generate highly processable and highly conductive films. Conductivity can be optimized by limiting the time of reaction to 12 h. At this point of the reaction, the PEDOT/PSS segments, appearing as broad band in the electropherogram, could still exist in an extended coil conformation favoring charge transport resulting in high conductivity. Above a threshold PEDOT length formed at reaction times longer than 12 h, the PEDOT/PSS complex, appearing as spikes in the electropherogram, most likely have undergone a conformational change to coiled core‐shell structure restricting charge transport resulting in low conductivity. The optimal conductivity (5.2 S/cm) of films from dispersions synthesized for 12 h is significantly higher than those from its commercial equivalent Clevios P and other reported values obtained under similar conditions without the addition of codopants.     

Hollow microstructures of polypyrrole doped by poly(styrene sulfonic acid)

Microstructures with hollow interiors, such as microspheres, microcrocks, microbowls, and micropumpkins, were prepared through the direct electrochemical oxidation of pyrrole in an aqueous solution of poly(styrene sulfonic acid) (PSSA). Scanning electron microscopy demonstrated that the microstructures possessed hollow interiors. The addition of polymeric doping ions made the skins of the microstructures very smooth, and several novel structures were observed. The morphology of the microstructures was simply modulated through changes in the electrochemical conditions. Raman and Fourier transform infrared characterizations indicated that the microstructures were made of conductive polypyrrole (PPy) doped by polymeric anions of poly(styrene sulfonate), and X‐ray diffraction showed that the microstructures were amorphous. Thermogravimetric analysis indicated that PPy–PSSA composite films with microstructures had higher thermal stability than pure PPy, PPy‐coated PSSA microspheres, and naphthalene sulfonic acid doped PPy microstructures. Furthermore, PPy–PSSA composite films with microstructures showed cation‐exchange behavior during the redox process in aqueous solutions of sodium dodecyl benzenesulfonate. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3170–3177, 2004     

Proton conducting membranes based on poly(vinyl chloride) graft copolymer electrolytes

The direct preparation of proton conducting poly(vinyl chloride) (PVC) graft copolymer electrolyte membranes using atom transfer radical polymerization (ATRP) is demonstrated. Here, direct initiation of the secondary chlorines of PVC facilitates grafting of a sulfonated monomer. A series of proton conducting graft copolymer electrolyte membranes, i.e. poly(vinyl chloride)‐g‐poly(styrene sulfonic acid) (PVC‐g‐PSSA) were prepared by ATRP using direct initiation of the secondary chlorines of PVC. The successful syntheses of graft copolymers were confirmed by ¹H‐NMR and FT‐IR spectroscopy. The images of transmission electron microscopy (TEM) presented the well‐defined microphase‐separated structure of the graft copolymer electrolyte membranes. All the properties of ion exchange capacity (IEC), water uptake, and proton conductivity for the membranes continuously increased with increasing PSSA contents. The characterization of the membranes by thermal gravimetric analysis (TGA) also demonstrated their high thermal stability up to 200°C. The membranes were further crosslinked using UV irradiation after converting chlorine atoms to azide groups, as revealed by FT‐IR spectroscopy. After crosslinking, water uptake significantly decreased from 207% to 84% and the tensile strength increased from 45.2 to 71.5 MPa with a marginal change of proton conductivity from 0.093 to 0.083 S cm^?1, which indicates that the crosslinked PVC‐g‐PSSA membranes are promising candidates for proton conducting materials for fuel cell applications. Copyright © 2008 John Wiley & Sons, Ltd.     

Poly(styrene sulfonic acid)–poly(vinylidene fluoride) interpolymer ion-exchange membranes. II. Ultrafiltration properties

Highly porous interpolymer ion-exchange membranes of poly(styrene sulfonic acid) and poly(vinylidene fluoride) have been investigated under pressure filtration with KCI, Na₂SO₄, erythrosin, and bovine serum albumin as solutes in the feed solution. The rejection of the ionic solutes is governed by a Donnan exclusion of electrolyte from the membrane phase. A model for the transport behavior is proposed that includes both diffusive and convective salt transport. The calculated rejections agree adequately with the observed data.     

Applications of poly(3,4-ethylenedioxythiophene) doped with poly(styrene sulfonic acid) transistors in chemical and biological sensors

The application of transistors based on poly(3,4-ethylenedioxythiophene) doped with poly(styrene sulfonic acid) (PEDOT:PSS) in chemical and biological sensing is reviewed. These devices offer enormous potential for facile processing of small, portable, and inexpensive sensors ideally suited for point-of-care analysis. They can be used to detect a wide range of analytes for a variety of possible applications in fields such as health care (medical diagnostics), environmental monitoring (airborne chemicals, water contamination, etc.), and food industry (smart packaging). Organic transistors are excellent candidates to act as transducers because they have the ability to translate chemical and biological signals into electronic signals with high sensitivity. Furthermore, fuctionalization of PEDOT:PSS films with a chemical or biological receptor can lead to high specificity. The advantages of using PEDOT:PSS transistors are described, and applications are presented for sensing analytes in both gaseous and aqueous environments.     

Electric field processing to control the structure of poly(vinylidene fluoride) composite proton conducting membranes

A novel method is reported for controlling the structure of poly(vinylidene fluoride) (PVdF) composite proton conducting membranes. When proton conducting Nafion or zirconium phosphate sulfophenylenphosphonate (ZrPSPP) particles are dispersed in a mixed colloidal suspension with PVdF particles, the proton conducting particles selectively respond to an applied electric field. Under appropriate conditions, the proton conducting particles are induced to assemble into chains that rapidly grow to span the gap between electrodes as the electric field is applied. By removing the solvent and melting the PVdF phase while applying the electric field, composite membranes were formed that have field-induced structure. In comparison to randomly structured composites, the electric field-processed Nafion/PVdF or ZrPSPP/PVdF composite membranes showed improved proton conductivity, water sorption, selectivity for protons over methanol, and controlled surface area changes upon swelling with water. The transport and mechanical properties of the electric field-processed composite membranes suggest the potential for improved performance in direct methanol fuel cells.     

Poly(styrene sulfonic acid)–poly(vinylidene fluoride) interpolymer ion-exchange membranes. I. Preparation and characterization

Highly porous interpolymer ion-exchange membranes have been prepared from poly(styrene sulfonic acid), PSSA and poly(vinylidene fluoride) PVdF using a casting solvent of dimethylformamide and hexamethylphosphoramide. The membranes have been characterized by their water content, concentration potential, ionic conductivity, and their hydraulic permeability. An estimation of the porosity of the membranes has been made from the relative conductance of the potassium and the tetrabutylammonium ions in the film. This porosity has been compared with that derived from a consideration of the water flux through a Poiseuille-type pore.     

Effects of Supporting Electrolytes on Spectroelectrochemical and Electrochromic Properties of Polyaniline‐poly(styrene sulfonic acid) and Poly(ethylenedioxythiophene)‐poly(styrene sulfonic acid)‐based Electrochromic Device

Electrochromic devices are fabricated by using polyaniline (PANI) doped with poly(styrene sulfonic acid) (PSS) as coloring electrodes, poly(ethylenedioxythiophene)‐poly(styrene sulfonic acid) (PEDOT‐PSS) as complementary electrodes, and hybrid polymer electrolytes as gel electrolytes. The device based on LiClO₄‐based electrolyte (weight ratio of PMMA:PC:LiClO₄ = 0.7:1.1:0.3) shows the highest optical contrast and coloration efficiency (333 cm²/C) after 1200 cycles in these devices, and the color changes from pale yellow (?0.5 V) to dark blue (+2.5 V). The spectroelectrochemical and electrochromic switching properties of electrochromic devices are investigated, the maximum optical contrast (ΔT%) of electrochromic device for ITO|PANI‐PSS‖PMMA‐PC‐LiClO₄‐SiO₂‖PEDOT‐PSS|ITO are 31.5% at 640 nm, and electrochromic device based on LiClO₄‐based electrolyte with SiO₂ shows faster response time than that based on LiClO₄‐based electrolyte without SiO₂.     

A far-infrared study of ionic interactions in poly(styrene sulfonic acid) ionomers

The far-infrared spectra of poly(styrene sulfonic acid) (PSSA) ionomer films containing alkaline and alkaline earth ions have been studied, and strong, broad bands, whose frequencies are cation dependent, have been observed and assigned to cation motion. The force field elements for cations vibrating at sulfonate-containing sites have been obtained for different models of the cation-motion vibration. The effects of hydration, dehydration, and thermal annealing are discussed in light of ion clustering in these materials.     

Aligned poly (glycolide‐lactide) fiber membranes with conducting polypyrrole

Electroactive polypyrrole (PPy) are highly attractive for a number of biomedical applications such as tissue engineering. To improve interfacial compatibility of PPy with biopolyesters, poly (?‐caprolactone) grafted PPy (PPy‐g‐PCL) are synthesized in this work and characterized with Fourier transform infrared and nuclear magnetic resonance. PPy‐g‐PCL exhibits good conductivity and electrochemical activity. It is also blended with poly (glycolide‐lactide) to make aligned fiber membranes via drum at the speed of 1500 r/min. The relationships of blending ratio with the fibrous structure, thermal stability, wettability, and mechanical properties are clarified. The results show that blending PPy‐g‐PCL has no significant effect on the fibrous morphology, but fibers trends aligned architecture as the blend ratio of poly (glycolide‐lactide)/PPy‐g‐PCL exceeds 70/30. The membranous thermal and mechanical stability are modified. The membranous hydrophilicity significantly enhances with PPy‐g‐PCL amount increasing. Then the fiber membrane with topographical and electrical cues is qualified as the application of tissue engineering. Copyright © 2016 John Wiley & Sons, Ltd.     

Novel conducting polymer electrolyte biosensor based on poly(1-vinyl imidazole) and poly(acrylic acid) networks

Biosensor construction and characterization studies of poly(acrylic acid) (PAA) and poly(1-vinyl imidazole) (PVI) complex systems have been carried out. The biosensors were prepared by mixing PAA with PVI at several stoichiometric ratios, x (molar ratio of the monomer repeat units). The enzyme, invertase, was entrapped in the PAA/PVA interpenetrating polymer networks during complexation. Modifications were made on the PAA/PVI conducting polymer electrolyte matrixes to improve the stability and performance of the polymer electrolyte-based enzyme biosensor. The maximum reaction rate (V(max)) and Michaelis-Menten constant (K(m)) were investigated for the immobilized invertase. The temperature and pH optimization, operational stability, and shelf life of the polymer electrolyte biosensor were also examined.