Physico–chemical properties of CdO–Al2O3 catalysts. I – Structural characteristics

Alumina gels AN6 and AN7 were prepared by precipitation with NaOH from hydrated aluminum sulfate at pH 6 and 7, respectively. A third alumina gel AA7 was similarly prepared, but by precipitation with 30% ammonia. Pure cadmia C8 and C9 were precipitated from cadmium sulfate at pH 8 and 9 using NaOH. Five mechanically mixed gels ACM (1:0.25), ACM (1:0.5), ACM (1:1), ACM (0.5:1) and ACM (0.25:1) were prepared by thoroughly mixing the appropriate molar ratios of AN7 and C8. Also, five coprecipitated gels ACC (1:0.25), ACC (1:0.5), ACC (1:1), ACC (0.5:1) and ACC (0.25:1) were coprecipitated by dropping simultaneously the appropriate volumes of 1 M aluminum sulfate, 1 M cadmium sulfate and 3 M NaOH. Calcination products at 400, 500, 600, 800 and 1000 °C were obtained from each preparation.TG–DTA patterns of uncalcined samples were analyzed and the XRD of all 1000 °C-products and some selected samples calcined at 400–800 °C were investigated. The thermal behaviors of pure and mixed gels depend on the precipitating agent, pH of precipitation, chemical composition and method of preparation. Generally, calcination at temperatures below 800 °C gave poorly crystalline phases. Well crystalline phases are obtained at 800 and 1000 °C. For pure alumina γ-Al₂O₃ was shown as 400 °C-calcination product that transforms into the δ form around 900 °C and later to θ-Al₂O₃ as a major phase and α-Al₂O₃ as a minor phase at 1000 °C. CdO was shown by 500 °C-calcined cadmia gel that showed color changes with rise of calcination temperature. The most stable black cadmium oxide phase (Monteponite) is obtained upon calcination at 1000 °C. Thousand degree celsius- calcined mixed oxides showed θ-Al₂O₃, α-Al₂O₃, CdAl₂O₄ and monteponite which dominate depending on the chemical composition.     

Structure and properties of glasses in the system Li2O–SnO–B2O3

Glasses in the system Li₂O–SnO–B₂O₃ system were prepared by a melt-quenching method. Thermal and viscous properties and local structure of these glasses were investigated. The SnO–B₂O₃ glasses exhibited relatively low glass-transition temperatures (T_g) around 350 °C and excellent thermal stability against crystallization. Viscosity measurements in the vicinity of T_g indicated that the glasses were considerably fragile compared to alkali borate glasses. Fraction of four-coordinated boron was maximized at the composition with 50 mol% SnO and that of nonbridging oxygen, which is not purely ionic in alkali borate systems but partially covalent, augmented with an increase in the SnO content. Correlation between glass properties and structure was discussed in the SnO–B₂O₃ binary system.     

Highly dispersed Mn2O3−Co3O4 nanostructures on carbon matrix as heterogeneous Fenton-like catalyst

This work reports the synthesis of various carbon (Vulcan XC-72 R) supported metal oxide nanostructures, such as Mn₂O₃, Co₃O₄ and Mn₂O₃−Co₃O₄ as heterogeneous Fenton-like catalysts for the degradation of organic dye pollutants, namely Rhodamine B (RB) and Congo Red (CR) in wastewater. The activity results showed that the bimetallic Mn₂O₃−Co₃O₄/C catalyst exhibits much higher activity than the monometallic Mn₂O₃/C and Co₃O₄/C catalysts for the degradation of both RB and CR pollutants, due to the synergistic properties induced by the Mn−Co and/or Mn (Co)−support interactions. The degradation efficiency of RB and CR was considerably increased with an increase of reaction temperature from 25 to 45°C. Importantly, the bimetallic Mn₂O₃−Co₃O₄/C catalyst could maintain its catalytic activity up to five successive cycles, revealing its catalytic durability for wastewater purification. The structure–activity correlations demonstrated a probable mechanism for the degradation of organic dye pollutants in wastewater, involving •OH radical as well as Mn²⁺/Mn³⁺ or Co²⁺/Co³⁺ redox couple of the Mn₂O₃−Co₃O₄/C catalyst.     

209Bi NQR in Mixed Oxides 2Bi2O3· B2O3, 3Bi2O3· 5B2O3, and Bi2O3· 3B2O3

It was earlier found from nuclear quadrupole resonance (NQR) measurements and computer modeling that -Bi₂O₃, Bi₃O₄Br and mixed oxides Bi₂O₃· 2Al₂O₃, Bi₂O₃· 2Ga₂O₃, Bi₂O₃· 3GeO₂, and 2Bi₂O₃· 3GeO₂exhibit local ordered magnetic fields from 30 to 200 G. It thus follows that these compounds are not diamagnets in a conventional sence of the word. With the aim of revealing previously unknown magnetic properties in bismuth(III) oxide-based Main Group element compounds, the mixed bismuth–boron oxides 2Bi₂O₃· B₂O₃, 3Bi₂O₃· 5B₂O₃, and Bi₂O₃· 3B₂O₃were prepared and studied using ²⁰⁹Bi NQR. The quadrupole interactions of the ²⁰⁹Bi nuclei and their electronic environment were studied, the crystallochemical features of the compounds were discussed, and the conformity of the ²⁰⁹Bi results to the X-ray structure data was verified. The preliminary tests in the field of a permanent magnet showed that the resonance intensities increase in external magnetic fields, indicating that a magnetism of unknown nature develops in the titled compounds. It was found reasonable to continue studies of the magnetic properties of these compounds using single-crystal ²⁰⁹Bi NQR in external magnetic fields.     

Magnetic and optical investigation of 40SiO2·30Na2O·1Al2O3·(29 − x)B2O3·xFe2O3 glass matrix

Samples of 40SiO₂·30Na₂O·1Al₂O₃·(29 − x)B₂O₃·xFe₂O₃ (mol%), with 0.0 ≤ x ≤ 17.5, were prepared by the fusion method and investigated by electron paramagnetic resonance (EPR), optical absorption (OA) and Mössbauer spectroscopy (MS). The EPR spectra of the as-synthesized samples exhibit two well-defined EPR signals around g = 4.27 and g = 2.01 and a visible EPR shoulder around g = 6.4, assigned to isolated Fe³⁺ ion complexes (g = 4.27 and g = 6.4) and Fe³⁺-based clusters (g = 2.01). Analyses of both EPR line intensity and line width support the model picture of Fe³⁺-based clusters built in from two sources of isolated ions, namely Fe²⁺ and Fe³⁺; the ferrous ion being used to build in iron-based clusters at lower x-content (below about x = 2.5%) whereas the ferric ion is used to build in iron-based clusters at higher x-content (above about x = 2.5%). The presence of Fe²⁺ ions incorporated within the glass template is supported by OA data with a strong band around 1100 nm due to the spin-allowed ⁵E_g–⁵T_2g transition in an octahedral coordination with oxygen. Additionally, Mössbauer data (isomer shift and quadrupole splitting) confirm incorporation of both Fe²⁺ and Fe³⁺ ions within the template, more likely in tetrahedral-like environments. We hypothesize that ferrous ions are incorporated within the glass template as FeO₄ complex resulting from replacing silicon in non-bridging oxygen (SiO₃O⁻) sites whereas ferric ions are incorporated as FeO₄ complex resulting from replacing silicon in bridging-like oxygen silicate groups (SiO₄).     

Sol–gel derived cordierite glass–ceramic doped CaO and B2O3: sintering, crystallization and phase transformation characteristics

In the present work, cordierite glass–ceramic with stoichiometric composition containing 5 wt% CaO and different amounts of B₂O₃ was prepared by sol–gel processing. The powders were synthesized by tetraethyl orthosilicate (TEOS), magnesium and aluminum chlorides. Crystallization and sintering behavior of glass–ceramics was investigated at different temperatures. Different steps of phase transformations to cordierite have been studied by DSC and XRD. Various phases have been formed at different heat-treatment temperatures. The results showed that adding 1 wt% B₂O₃ led to a decrease in both the glass transition temperature (T_g) and the crystallization peak temperature (T_p). In contrast, with increasing B₂O₃ content from 1 to 3 and 5 wt%, both T_g and T_p of samples increased. The results of sintering showed that crystallization before complete sintering hindered good sintering. However, low content of B₂O₃ relatively improved sintering than the others.     

Influence of redox behavior of copper ions on dielectric and spectroscopic properties of Li2O–MoO3–B2O3: CuO glass system

Li₂O–MoO₃–B₂O₃ glasses mixed with different concentrations of CuO (ranging from 0 to 1.2 mol%) were prepared. The samples were characterized by X-ray diffraction, scanning electron microscopy and differential scanning calorimetry. Optical absorption, luminescence, ESR, IR and dielectric properties (viz., dielectric constant ?′, loss tan δ and a.c. conductivity σ_ac, over a wide range of frequency and temperature) of these glass materials have been investigated. The results of differential scanning calorimetric studies suggest that the glass forming ability is higher for the glasses containing CuO beyond 0.6 mol%. The analysis of results of the dielectric properties has revealed that the glasses possess high insulating strength when the concentration of CuO is >0.6 mol%. The variation of a.c. conductivity with the concentration of CuO passes through a maximum at 0.6 mol%. In the high-temperature region, the a.c. conduction seems to be connected with the mixed conduction viz., electronic conduction and ionic conduction. The optical absorption spectra of these glasses exhibited bands due to Cu⁺ ions in the UV region in addition to the conventional band due to Cu²⁺ ions in the visible region. The ESR spectral studies have indicated that there is a gradual adoption of Cu²⁺ ions from ionic environment to covalent environment as the concentration of CuO increases beyond 0.6 mol% in the glass matrix. The luminescence spectra excited at 271 nm have exhibited an intense yellow emission band centered at about 550 nm and a relatively broad blue emission band at about 450 nm; these bands have been attributed to the ³D₁ → ¹S₀ transition of isolated Cu⁺ ions and ³D₁ → ¹S₀ transition of (Cu⁺)₂ pairs, respectively. The quantitative analysis of the results of all these studies has indicated that as the concentration of CuO is increased beyond 0.6 mol% in the glass matrix, a part of Cu²⁺ ions have been reduced to Cu⁺ ions that have influenced the physical properties of these glasses to a substantial extent.     

Thermodynamic properties of two zinc borates: 3ZnO·3B2O3·3.5H2O and 6ZnO·5B2O3·3H2O

Two pure zinc borates with microporous structure 3ZnO·3B₂O₃·3.5H₂O and 6ZnO·5B₂O₃·3H₂O have been synthesized and characterized by XRD, FT-IR, TG techniques and chemical analysis. The molar enthalpies of solution of 3ZnO·3B₂O₃·3.5H₂O(s) and 6ZnO·5B₂O₃·3H₂O(s) in 1 mol · dm⁻³ HCl(aq) were measured by microcalorimeter at T = 298.15 K, respectively. The molar enthalpies of solution of ZnO(s) in the mixture solvent of 2.00 cm³ of 1 mol · dm⁻³ HCl(aq) in which 5.30 mg of H₃BO₃ were added were also measured. With the incorporation of the previously determined enthalpy of solution of H₃BO₃(s) in 1 mol · dm⁻³ HCl(aq), together with the use of the standard molar enthalpies of formation for ZnO(s), H₃BO₃(s), and H₂O(l), the standard molar enthalpies of formation of −(6115.3 ± 5.0) kJ · mol⁻¹ for 3ZnO·3B₂O₃·3.5H₂O and −(9606.6 ± 8.5) kJ · mol⁻¹ for 6ZnO·5B₂O₃·3H₂O at T = 298.15 K were obtained on the basis of the appropriate thermochemical cycles.     

Phase evolution and electrical properties of BaO–SrO–TiO2–SiO2–Al2O3-based glass ceramics prepared by sol–gel process

Crystallization of BaO–SrO–TiO₂–SiO₂–Al₂O₃-based glass ceramics, prepared by sol–gel process, was evaluated in terms of the effect of sintering temperature on phase evolution and electrical properties. The characterization of the samples was performed by X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) studies and impedance spectroscopy analysis. The XRD results demonstrate that fresnoite phase starts to crystallize at 700 °C and perovskite phase appears at 900 °C. The glass ceramic samples sintered at high temperatures contained three crystalline phases, including perovskite, feldspar and fresnoite. In addition, SEM observation showed that the average grain size increased and the porosity decreased with increasing sintering temperature. Furthermore, the measurement of impedance spectroscopy suggests that there is a minimum value of the activation energy associated with the sintering temperature of the glass ceramics. The possible explanation of the sintering temperature dependence was discussed.     

Preparation of 2CaO·3B2O3·H2O nanomaterials and evaluation of their flame retardant properties by a thermal analysis method

Different morphologies of calcium borate 2CaO·3B₂O₃·H₂O, nanoribbon, bundle-like nanostructure and fan-shaped non-nanostructure, have been prepared under hydrothermal conditions, which were characterized by XRD, FT-IR, TGA and SEM. Their flame retardant properties to the polypropylene were investigated by thermal analysis method (including TG, DSC and non-isothermal decomposition kinetics) and oxygen index method. With the decrease in TG mass loss, the increase in heat absorption for DSC in N₂ atmosphere, the increase in LOI values, and the increase in apparent activation energy E_a, the flame retardant properties of prepared 2CaO·3B₂O₃·H₂O samples increased gradually from non-nanostructure to bundle-like nanostructure and then to nanoribbon. This trend may be ascribed to their sizes being decreased accordingly. The flame retarding mechanism has been proposed. The mechanical property of polypropylene/2CaO·3B₂O₃·H₂O composite material has also been evaluated. It can be predicted that 2CaO·3B₂O₃·H₂O nanoribbon could serve as an excellent flame retardant.

     

CHF3…H2O complex revisited: a matrix isolation and ab initio study

Structural Chemistry - The structural and spectroscopic features of the CHF3…H2O complex have been investigated using high-level ab initio calculations and IR matrix isolation spectroscopy....     

Synthesis and thermochemical characteristics of Na2O · Al2O3 · 2.5H2O

A pure phase of monosodium aluminate hydrate Na₂O · Al₂O₃ · 2.5H₂O (MAH) is synthesized and characterized by means of XRD, IR, SEM, TGA, and DSC. The heat capacity of the compound is measured in the temperature range of ?100 to 100°C, and the thermal contributions to enthalpy and entropy are calculated. The standard entropy, enthalpy, and Gibbs energy of formation of MAH at 298 K are estimated.     

Oxygen deficient α-Fe2O3 photoelectrodes: a balance between enhanced electrical properties and trap-mediated losses

Intrinsic doping of hematite through the inclusion of oxygen vacancies (V_O) is being increasingly explored as a simple, low temperature route to preparing active water splitting α-Fe₂O_3–x photoelectrodes. Whilst it is widely accepted that the introduction of V_O leads to improved conductivities, little else is verified regarding the actual mechanism of enhancement. Here we employ transient absorption (TA) spectroscopy to build a comprehensive kinetic model for water oxidation on α-Fe₂O_3–x. In contrast to previous suggestions, the primary effect of introducing V_O is to block very slow (ms) surface hole – bulk electron recombination pathways. In light of our mechanistic research we are also able to identify and address a cause of the high photocurrent onset potential, a common issue with this class of electrodes. Atomic layer deposition (ALD) of Al₂O₃ is found to be particularly effective with α-Fe₂O_3–x, leading to the photocurrent onset potential shifting by ca. 200 mV. Significantly TA measurements on these ALD passivated electrodes also provide important insights into the role of passivating layers, that are relevant to the wider development of α-Fe₂O₃ photoelectrodes.     

Characteristics and retention properties of a mesoporous γ-Al2O3 membrane for nanofiltration

A mesoporous γ-Al₂O₃ membrane was produced by the sol gel dipping technique, followed by a thermal treatment (calcination and sintering). Different sintering temperatures were applied, which led to membranes with an average pore diameter ranging from 8.7 to 3.4 nm, the latter one corresponding to a MWCO of 900 Da.Salt retention was very much dependent on the pH of the solution as such membranes have an amphoteric character. Minimal salt retention was found at the isoelectric point (pH 7.5). Experiments were carried out with NaCl, MgCl₂ and LaCl₃ at different concentrations and in both single salt solutions and mixtures. The results are interpreted in terms of Donnan exclusion and in terms of the formation of an electrical double layer in the pores.Dynamic corrosion tests showed that some corrosion occurs at a pH of 2 or lower.     

Structure,chemical stability and electrical properties of BaCe0.9Y0.1O3−δ modified with V2O5

Wet vacuum impregnation method was applied in order to evaluate the possibility of the formation of the material in BaCe_0.9Y_0.1O_3?δ–V₂O₅ system. Single-phase BaCe_0.9Y_0.1O_3?δ samples, synthesised by solid-state reaction method, were impregnated with the solution of vanadium(V) oxide precursor. Multi-step, multi-cycle impregnation procedure was applied to enhance the impregnation efficiency. Partial decomposition of Y-doped BaCeO₃ in contact with the solution of the precursor, resulting in the formation of vanadium containing phases (CeVO₄ and BaV₂O₆) on the materials surface, was observed. However, the presence of vanadium was also confirmed for the inner parts of the materials. The synthesised materials were submitted for exposition test to evaluate their chemical stability towards CO₂/H₂O. All BaCe_0.9Y_0.1O₃-based materials modified by impregnation revealed higher chemical stability in comparison with single-phase un-modified BaCe_0.9Y_0.1O_3?δ, since the amount of barium carbonate formed during the exposition was significantly lower. The total electrical conductivity of the received multi-phase materials was generally slightly lower than for the reference BaCe_0.9Y_0.1O_3?δ sample, since the presence of the additional phases had a blocking effect on materials conductivity. The values of BaCeO₃ lattice parameters and the Seebeck coefficient did not show the modification of the defects structure of Y-doped BaCeO₃ during applied synthesis procedure.

     

Hydrothermal synthesis and thermodynamic properties of 2ZnO · 3B2O3 · 3H2O

The important zinc borate of 2ZnO · 3B₂O₃ · 3H₂O has been synthesized and characterized by means of chemical analysis, XRD, FT-IR, and DTA–TG techniques. The molar enthalpies of solution of H₃BO₃(s) in HCl · 54.561H₂O, of ZnO(s) in the mixture of HCl · 54.561H₂O and calculated amount of H₃BO₃, and of 2ZnO · 3B₂O₃ · 3H₂O(s) in HCl · 54.604H₂O were measured, respectively. With the use of the standard molar enthalpies of formation for ZnO(s), H₃BO₃(s), and H₂O(l), the standard molar enthalpy of formation of ?(5561.7 ± 4.9) kJ · mol^?1 for 2ZnO · 3B₂O₃ · 3H₂O(s) was obtained. Thermodynamic properties of this compound were also calculated by a group contribution method.