干燥方式对高氯酸铵/石墨烯复合材料的结构和热分解行为的影响

通过溶胶-凝胶法制备了石墨烯水凝胶, 并将其与高氯酸铵(AP)复合, 然后分别采用自然干燥、冷冻干燥和超临界CO₂干燥三种干燥方式制备了AP/石墨烯复合材料, 并通过扫描电镜(SEM)、元素分析、X射线衍射(XRD)、差示扫描量热仪(DSC)和热重-红外联用技术(TG-FTIR)研究了不同干燥方式对其结构和热分解行为的影响. 结果表明, 干燥方式对AP/石墨烯复合材料的形貌具有明显影响, 其中通过超临界CO₂干燥制备的AP/石墨烯复合材料基本能保持与石墨烯气凝胶相似的外观和多孔结构. 通过自然干燥、冷冻干燥和超临界CO₂干燥制备的AP/石墨烯复合材料中AP的质量分数分别为89.97%、92.41%和94.40%, 其中通过超临界CO₂干燥制备的复合材料中AP的粒径尺寸为69 nm. DSC测试结果表明, 石墨烯对AP的热分解过程具有明显的促进作用, 能使AP的低温分解过程大大减弱, 高温分解峰温明显降低. 三种干燥方式相比, 通过超临界CO₂干燥制备的AP/石墨烯复合材料中石墨烯的促进作用最明显. 与纯AP相比, 其高温分解峰温降低了83.7℃, 表观分解热提高到2110 J·g^-1. TG-FTIR分析结果表明, AP/石墨烯复合材料的热分解过程中, AP分解产生的氧化性产物与石墨烯发生了氧化反应, 生成了CO₂.     

Facile Preparation and Lithium Storage Properties of TiO2@Graphene Composite Electrodes with Low Carbon Content

Over the past decade, TiO₂/graphene composites as electrodes for lithium ion batteries have attracted a great deal of attention for reasons of safety and environmental friendliness. However, most of the TiO₂/graphene electrodes have large graphene content (9–40 %), which is bound to increase the cost of the battery. Logically, reducing the amount of graphene is a necessary part to achieve a green battery. The synthesis of TiO₂ nanosheets under solvothermal conditions without additives is now demonstrated. Through mechanical mixing TiO₂ nanosheets with different amount of reduced graphene (rGO), a series of TiO₂@graphene composites was prepared with low graphene content (rGO content 1, 2, 3, and 5 wt %). When these composites were evaluated as anodes for lithium ion batteries, it was found that TiO₂+3 wt % rGO manifested excellent cycling stability and a high specific capacity (243.7 mAh g^?1 at 1 C; 1 C=167.5 mA g^?1), and demonstrated superior high‐rate discharge/charge capability at 20 C.     

Investigate on mechanical and tribological properties of solution styrene butadiene and butadiene rubber composites

Solution styrene butadiene and butadiene rubber (SSBR‐BR) composites reinforced with different contents of SiO₂‐graphene have been fabricated firstly. The mechanical properties of the rubber composites were comparatively investigated using tensile tests; experimental results showed that, as an overall trend, the tensile and tear strength increased with increasing contents of SiO₂‐graphene. Most importantly, under the condition of simulating practical working condition, the tribological behavior of SSBR‐BR composites with different contents of SiO₂‐graphene was explored via a universal ring‐plate frictional tester in detail. Combined with the surface roughness of the counterparts, the wear mechanisms were discussed for SSBR‐BR composites under the cement and asphalt counterparts. Finally, several wear mechanisms under different actual working conditions were proposed.     

金红石相TiO2-石墨烯复合材料的制备及其光催化性能

以鳞片石墨为原料, 用改进的Hummers法制备氧化石墨烯(GO), 以异丙醇钛为钛源经一步水热法制备得到金红石相TiO₂-石墨烯复合材料(rGO-TiO₂), 考察了氧化石墨烯用量对复合材料光催化性能的影响. 采用X射线衍射(XRD), 比表面积(BET), 透射电镜(TEM), 扫描电镜(SEM), 拉曼光谱, 紫外-可见(UV-Vis)吸收光谱和荧光光谱(PL)等测试手段对复合材料进行表征. 结果表明: 复合材料中TiO₂为针簇状结构的金红石相, 与石墨烯能够均匀复合; 与纯金红石相TiO₂相比, 复合材料具有较大的比表面积. 研究了该复合材料在紫外光下对罗丹明B 以及可见光下对甲基橙光降解效果. 当氧化石墨烯浓度为0.5 mg·mL^-1时, 制备得到的复合材料rGO-TiO₂具有较好的光催化效果.     

Thermal stability and conductivity of hot-pressed Si3N4–graphene composites

This study concerns new Si₃N₄–graphene composites manufactured using the hot-pressing method. Because of future applications of silicon nitride for cutting tools or specific parts of various devices having contact with high temperatures there is a need to find a ceramic composite material with good mechanical and especially thermal properties. Excellent thermal properties in the major directions are characteristic of graphene. In this study, the graphene phase is added to the silicon nitride phase in a quantity of up to 10 mass%, and the materials are sintered under uniaxial pressure. The mixture of AlN and Y₂O₃ is added as sintering activator to the composite matrix. The studies focus on thermal stability of produced composites in argon and air conditions up to the temperature of 1,000 °C. The research also concerns the influence of applied uniaxial pressure during the sintering process on the orientation of graphene nanoparticles in the Si₃N₄ matrix. The study also presents research on anisotropy of thermal diffusivity and following thermal conductivity of ceramic matrix composites versus the increasing graphene quantity. Most of the presented results have not been published in the literature yet.     

石墨烯/硫复合正极材料的一步水热法制备与电化学性能

将硫代硫酸钠（Na₂S₂O₃）与氧化石墨烯（GO）的混合溶液,在酸性条件下经过一步水热反应制备还原氧化石墨烯/硫（RGO/S）复合正极材料. 实验探索了水热温度、反应时间、碳硫质量比例对材料的影响. 通过X射线衍射（XRD）、扫描电镜（SEM）、透射电镜（TEM）和恒电流充放电对材料进行分析. 结果表明在180 ℃下,碳硫质量比为3：7时,水热12 h得到的RGO/S复合材料具有优异的循环性能,首次放电比容量为931 mAh·g^-1,50次循环之后其比容量还保持在828.16 mAh·g^-1;RGO/S复合材料的充放电库仑效率在95%以上;同时RGO/S复合材料的倍率性能相比于单质硫有很大提高. 一步水热法能够使硫分子均匀分布在石墨烯片层结构中,同时加强了石墨烯表面基团对硫分子的固定作用.     

Interlayer-expanded MoS<Subscript>2</Subscript>/graphene composites as anode materials for high-performance lithium-ion batteries

A facile strategy was developed to prepare interlayer-expanded MoS₂/graphene composites through a one-step hydrothermal reaction method. MoS₂ nanosheets with several-layer thickness were observed to uniformly grow on the surface of graphene sheets. And the interlayer spacing of MoS₂ in the composites was determined to expand to 0.95 nm by ammonium ions intercalation. The MoS₂/graphene composites show excellent lithium storage performance as anode materials for Li-ion batteries. Through gathering advantages including expanded interlayers, several-layer thickness, and composited graphene, the composites exhibit reversible capacity of 1030.6 mAh g^?1 at the current density of 100 mA g^?1 and still retain a high specific capacity of 725.7 mAh g^?1 at a higher current density of 1000 mA g^?1 after 50 cycles.     

Preparation of nano-structured LiFePO4/graphene composites by co-precipitation method

Graphene materials with superior electrical conductivities and high surface area would be advantageous for application in energy storage. And LiFePO₄ has been a promising electrode material however its poor conductivity limits its practical application. To improve the electronic conductivity, we prepare LiFePO₄/graphene composites in a co-precipitation method, in which graphene nanosheets are used as additives. The composites were characterized by X-ray diffraction (XRD) and atomic force microscopy (AFM), and their electrochemical properties were investigated by galvanostatic charge and discharge tests. The experimental results show that the capacity delivery and cycle performances of LiFePO₄ could be improved considerably by adding graphene. Therefore, LiFePO₄/graphene composites are a promising candidate for lithium secondary batteries.     

静电自组装方法合成的具有多孔三维网络结构的Fe3O4/石墨烯复合材料作为高性能锂离子电池负极材料

采用静电自组装方法,分两步合成Fe（OH）₃/GO前驱体（GO：氧化石墨烯）,再通过水热反应和600 ℃高纯氮气气氛下煅烧,获得了Fe₃O₄/石墨烯复合材料. 通过X射线衍射（XRD）、扫描电镜（SEM）、高分辨透射电镜（HRTEM）、拉曼（Raman）光谱等多种分析,发现该复合材料具有三维多孔石墨烯网络结构. 把合成的这种Fe₃O₄/石墨烯复合材料作为锂离子电池负极材料,电化学测试结果表明其具有优良的电化学性能：首次放电容量为1390 mAh·g^-1,50次循环后容量为819 mAh·g^-1. 通过对比实验表明,三维石墨烯网络结构的形成对复合材料的电化学循环稳定性起着关键作用.     

One‐pot synthesis of magnetic zeolitic imidazolate framework/grapheme oxide composites for the extraction of neonicotinoid insecticides from environmental water samples

Magnetic zeolitic imidazolate framework 67/graphene oxide composites were synthesized by one‐pot method at room temperature for the first time. Electrostatic interactions between positively charged metal ions and both negatively charged graphene oxide and Fe₃O₄ nanoparticles were expected to chemically stabilize magnetic composites to generate homogeneous magnetic products. The additional amount of graphene oxide and stirring time of graphene oxide, Co²⁺, and Fe₃O₄ solution were investigated. The zeolitic imidazolate framework 67 and Fe₃O₄ nanoparticles were uniformly attached on the surface of graphene oxide. The composites were applied to magnetic solid‐phase extraction of five neonicotinoid insecticides in environmental water samples. The main experimental parameters such as amount of added magnetic composites, extraction pH, ionic strength, and desorption solvent were optimized to increase the capacity of adsorbing neonicotinoid insecticides. The results show limits of detection at signal‐to‐noise ratio of 3 were 0.06–1.0 ng/mL under optimal conditions. All analytes exhibited good linearity with correlation coefficients of higher than 0.9915. The relative standard deviations for five neonicotinoid insecticides in environmental samples ranged from 1.8 to 16.5%, and good recoveries from 83.5 to 117.0% were obtained, indicating that magnetic zeolitic imidazolate framework 67/graphene oxide composites were feasible for analysis of trace analytes in environmental water samples.     

An in situ oxidation route to fabricate graphene nanoplate-metal oxide composites

We report our studies on an improved soft chemical route to directly fabricate graphene nanoplate-metal oxide (Ag₂O, Co₃O₄, Cu₂O and ZnO) composites from the in situ oxidation of graphene nanoplates. By virtue of H⁺ from hydrolysis of the metal nitrate aqueous solution and NO₃⁻, only a small amount of functional groups were introduced, acting as anchor sites and consequently forming the graphene nanoplate-metal oxide composites. The main advantages of this approach are that it does not require cumbersome oxidation of graphite in advance and no need to reduce the composites due to the lower oxidation degree. The microstructures of as-obtained metal oxides on graphene nanoplates can be dramatically controlled by changing the reaction parameters, opening up the possibility for processing the optical and electrochemical properties of the graphene-based nanocomposites.     

In situ growth of TiO2 in interlayers of expanded graphite for the fabrication of TiO2-graphene with enhanced photocatalytic activity

We present a facile route for the preparation of TiO₂–graphene composites by in situ growth of TiO₂ in the interlayer of inexpensive expanded graphite (EG) under solvothermal conditions. A vacuum‐assisted technique combined with the use of a surfactant (cetyltrimethylammonium bromide) plays a key role in the fabrication of such composites. Firstly, the vacuum environment promotes full infusion of the initial solution containing Ti(OBu)₄ and the surfactant into the interlayers of EG. Subsequently, numerous TiO₂ nanoparticles uniformly grow in situ in the interlayers with the help of the surfactant, which facilitates the exfoliation of EG under the solvothermal conditions in ethanol, eventually forming TiO₂–graphene composites. The as‐prepared samples have been characterized by Raman and FTIR spectroscopies, SEM, TEM, AFM, and thermogravimetic analysis. It is shown that a large number of TiO₂ nanoparticles homogeneously cover the surface of high‐quality graphene sheets. The graphene exhibits a multi‐layered structure (5–7 layers). Notably, the TiO₂–graphene composite (only 30 wt % of which is TiO₂) synthesized by subsequent thermal treatment at high temperature under nitrogen shows high photocatalytic activity in the degradation of phenol under visible and UV lights in comparison with bare Degussa P25. The enhanced photocatalytic performance is attributed to increased charge separation, improved light absorbance and light absorption width, and high adsorptivity for pollutants.     

Self‐Assembling Synthesis of Free‐standing Nanoporous Graphene–Transition‐Metal Oxide Flexible Electrodes for High‐Performance Lithium‐Ion Batteries and Supercapacitors

The synthesis of nanoporous graphene by a convenient carbon nanofiber assisted self‐assembly approach is reported. Porous structures with large pore volumes, high surface areas, and well‐controlled pore sizes were achieved by employing spherical silica as hard templates with different diameters. Through a general wet‐immersion method, transition‐metal oxide (Fe₃O₄, Co₃O₄, NiO) nanocrystals can be easily loaded into nanoporous graphene papers to form three‐dimensional flexible nanoarchitectures. When directly applied as electrodes in lithium‐ion batteries and supercapacitors, the materials exhibited superior electrochemical performances, including an ultra‐high specific capacity, an extended long cycle life, and a high rate capability. In particular, nanoporous Fe₃O₄–graphene composites can deliver a reversible specific capacity of 1427.5 mAh g^?1 at a high current density of 1000 mA g^?1 as anode materials in lithium‐ion batteries. Furthermore, nanoporous Co₃O₄–graphene composites achieved a high supercapacitance of 424.2 F g^?1. This work demonstrated that the as‐developed freestanding nanoporous graphene papers could have significant potential for energy storage and conversion applications.     

Impact of graphene on the enhancement of electrochemical and photocatalytic performance of Gd2O3 - Graphene nanocomposites

Gadolinium oxide - Graphene (Gd₂O₃-G) nanocomposites were prepared with different weight ratio of graphene using low temperature solution process. The structural, morphological, electrochemical and photocatalytic properties of the composites were investigated by X-ray diffraction, Raman, FE-SEM, HRTEM, Cyclic voltammetric and photo-degradation analysis. The chemical composition of the composites was studied by elemental mapping analysis using EPMA. The binding states of various elements present in the composites were analyzed by XPS. Cyclic voltammetric studies revealed that the nanocomposite with 5% graphene exhibits the specific capacitance of 26 F g⁻¹, which is higher than that of pure Gd₂O₃ (18 F g⁻¹). The presence of graphene has greatly enhanced the photocatalytic performance of Gd₂O₃G composites as the rate of degradation of MB dye is relatively higher in the composites compared to pure Gd₂O₃. The significant increase in the specific capacitance and rate of degradation of dye suggest that the Gd₂O₃G is a promising material for energy storage and environmental applications.     

Graphene-encapsulated Fe3O4 nanoparticles with 3D laminated structure as superior anode in lithium ion batteries

Fe₃O₄–graphene composites with three‐dimensional laminated structures have been synthesised by a simple in situ hydrothermal method. From field‐emission and transmission electron microscopy results, the Fe₃O₄ nanoparticles, around 3–15 nm in size, are highly encapsulated in a graphene nanosheet matrix. The reversible Li‐cycling properties of Fe₃O₄–graphene have been evaluated by galvanostatic discharge–charge cycling, cyclic voltammetry and impedance spectroscopy. Results show that the Fe₃O₄–graphene nanocomposite with a graphene content of 38.0 wt % exhibits a stable capacity of about 650 mAh g^?1 with no noticeable fading for up to 100 cycles in the voltage range of 0.0–3.0 V. The superior performance of Fe₃O₄–graphene is clearly established by comparison of the results with those from bare Fe₃O₄. The graphene nanosheets in the composite materials could act not only as lithium storage active materials, but also as an electronically conductive matrix to improve the electrochemical performance of Fe₃O₄.     

Graphite and Solvothermally Synthesized LiFePO<Subscript>4</Subscript>/Graphene Electrode for Soft-Packed Cell

Well-crystallized and nano-sized LiFePO₄/graphene composite have been successfully synthesized by in-situ disperse graphene oxide (GO) in precursor via a rapid microwave-solvothermal process at 200°C within 10 min. In spite of the low synthesis temperature, the structural and morphological properties of as-prepared composites are of high specific capacity, an excellent high rate capability, and stable cycling performance. In comparison with LiFePO₄/grahite soft-packed full-cell, the assembled soft-packed full-cell with solvothermally synthesized LiFePO₄/graphene composite and graphite electrode show better cycle performances prepared at higher temperature.     

Mild Synthesis of Pt/SnO2/Graphene Nanocomposites with Remarkably Enhanced Ethanol Electro‐oxidation Activity and Durability

We have designed a new Pt/SnO₂/graphene nanomaterial by using L ‐arginine as a linker; this material shows the unique Pt‐around‐SnO₂ structure. The Sn²⁺ cations reduce graphene oxide (GO), leading to the in situ formation of SnO₂/graphene hybrids. L ‐Arginine is used as a linker and protector to induce the in situ growth of Pt nanoparticles (NPs) connected with SnO₂ NPs and impede the agglomeration of Pt NPs. The obtained Pt/SnO₂/graphene composites exhibit superior electrocatalytic activity and stability for the ethanol oxidation reaction as compared with the commercial Pt/C catalyst owing to the close‐connected structure between the Pt NPs and SnO₂ NPs. This work should have a great impact on the rational design of future metal–metal oxide nanostructures with high catalytic activity and stability for fuel cell systems.     

Multi-stage Ordered Mesoporous Carbon-graphene Aerogel-Ni3S2/Co4S3 for Supercapacitor Electrode

Transition metal sulfides have emerged as promising materials in supercapacitor. In this work, we firstly developed an interface-induced superassembly approach to fabricate NiS_x and CoS_x nanoparticles, which based on ordered mesoporous carbon-graphene aerogel composites for supercapacitor electrodes. The obtained multi-component superassembled nanoparticles-carbon matrix composites have controllable 3D porous structure of multi-stage composite. The two-dimensional graphene interlaced to form a 3D framework with large sponge-like pores, and then the graphene surface was loaded with mesoporous carbon with mesoporous pore size and vertical orientation. The composites display high specific capacitance of 958.1 F g⁻¹ at 0.1 A g⁻¹. The capacitance retains about 97.3 % after 3000 charging-discharging cycles at 2 A g⁻¹. These results indicate that the obtained OMC−GA−Ni₃S₂/Co₄S₃ is a promising material for electrochemical capacitors, which providing new technical methods and ideas for the research of new energy and analytical sensor materials in the fields of energy storage, photocatalysis, point-of-care testing devices and other fields.     

Nonlinear optical properties of polyvinylcarbazole composites with graphene

The study has focused on polyvinylcarbazole (PVK) composites with graphene. It has been shown that there is a noticeable nonadditive shoulder on the long-wavelength edge of the optical absorption of PVK in these samples, which can be attributed to the formation of a charge-transfer complex between PVK as a donor and graphene as an acceptor. The formation of the complex causes a significant nonlinear optical effect in the PVK/graphene composite. The revealed increase in both the nonlinearity coefficient with increasing laser intensity and the cross section with increasing incident energy density is due to the formation of the graphene^?· radical anion, an additional species contributing to nonlinear absorption, with an increase in the radiation energy density. Nonlinear optical properties of PVK composites with graphene isolated from a solution in tetrachloroethane after 1.5-h centrifugation (sample 1) have been considered. It has been suggested that a significant decrease in optical transmission of laser radiation by the composite T _OA = 0.4 at an energy density at focus of 502 J/cm² is due to the formation of the PVK/graphene charge-transfer complex responsible for the nonadditive shoulder on the long-wavelength optical absorption edge of PVK. During photoexcitation of graphene in the PVK/graphene composites at a laser wavelength of 1064 nm, mobile holes are generated in PVK, indicating the formation of graphene^?· radical anions as a result of charge transfer from PVK to photoexcited graphene. The observed increase in both β with an increase in the laser radiation intensity and the cross section (σ_exc — σ₀) with an increase in the incident energy density may be due to either the contribution of nonlinear transitions (S ₀ → S ₂, S ₀ → S ₁ → S ₂, T ₁ → T ₂) or the formation of the additional species, the graphene-· radical anions, participating in nonlinear absorption by increasing the energy density at the focus (F _foc, J/cm²).     

Multifunctional Co3S4/Graphene Composites for Lithium Ion Batteries and Oxygen Reduction Reaction

Cobalt sulfide is a good candidate for both lithium ion batteries (LIBs) and cathodic oxygen reduction reaction (ORR), but low conductivity, poor cyclability, capacity fading, and structural changes hinder its applications. The incorporation of graphene into Co₃S₄ makes it a promising electrode by providing better electrochemical coupling, enhanced conductivity, fast mobility of ions and electrons, and a stabilized structure due to its elastic nature. With the objective of achieving high‐performance composites, herein we report a facile hydrothermal process for growing Co₃S₄ nanotubes (NTs) on graphene (G) sheets. Electrochemical impedance spectroscopy (EIS) verified that graphene dramatically increases the conductivity of the composites to almost twice that of pristine Co₃S₄. Electrochemical measurements indicated that the as‐synthesized Co₃S₄/G composites exhibit good cyclic stability and a high discharge capacity of 720 mA h g^?1 up to 100 cycles with 99.9 % coulombic efficiency. Furthermore, the composites react with dissolved oxygen in the ORR by four‐ and two‐electron mechanisms in both acidic and basic media with an onset potential close to that of commercial Pt/C. The stability of the composites is much higher than that of Pt/C, and exhibit high methanol tolerance. Thus, these properties endorse Co₃S₄/G composites as auspicious candidates for both LIBs and ORR.