Electrodeposition of MnO2 nanowires on carbon nanotube paper as free-standing,flexible electrode for supercapacitors

MnO₂ nanowires were electrodeposited onto carbon nanotube (CNT) paper by a cyclic voltammetric technique. The as-prepared MnO₂ nanowire/CNT composite paper (MNCCP) can be used as a flexible electrode for electrochemical supercapacitors. Electrochemical measurements showed that the MNCCP electrode displayed specific capacitances as high as 167.5 F g⁻¹ at a current density of 77 mA g⁻¹. After 3000 cycles, the composite paper can retain more than 88% of initial capacitance, showing good cyclability. The CNT paper in the composite acted as a good conductive and active substrate for flexible electrodes in supercapacitors, and the nanowire structure of the MnO₂ could facilitate the contact of the electrolyte with the active materials, and thus increase the capacitance.     

Conversion of porous PbO2 layers through galvanic displacement reaction with Mn2 + ions

The galvanic exchange between Mn^2 + ions and electrodeposited porous PbO₂ was studied to produce a porous oxide whose lower conductivity prevented its direct oxygen bubble-templated anodic deposition. Immersion of PbO₂ layers in acid acetate solutions of Mn^2 + led to the formation of amorphous MnO_x shell onto PbO₂. Due to its amorphous nature, MnO_x could not be proved to be MnO₂ by XRD. However, MnO_x was cathodically stripped at the same potential as MnO₂. The deposition of the MnO_x shell onto PbO₂ enhanced the capacity of the porous electrodes.     

Comments on stabilizing layered manganese oxide electrodes for Li batteries

An electrochemical study of structurally-integrated xLi₂MnO₃•(1 −x)LiMn_0.5Ni_0.5O₂ ‘composite’ materials has been undertaken to investigate the stability of electrochemically-activated electrodes at the Li₂MnO₃-rich end of the Li₂MnO₃–LiMn_0.5Ni_0.5O₂ tie-line, i.e., for 0.7 ≤ x ≤ 0.95. Excellent performance was observed for x = 0.7 in lithium half-cells; comparable to activated electrodes that have significantly lower values of x and are traditionally the preferred materials of choice. Electrodes with higher manganese content (x ≥ 0.8) showed significantly reduced performance. Implications for stabilizing low-cost, manganese-rich, layered lithium-metal-oxide electrode materials are discussed.     

Suppression of dendritic lithium formation by using concentrated electrolyte solutions

This study examined the electrochemical deposition and dissolution of lithium on nickel electrodes in a propylene carbonate (PC) electrolyte containing different LiN(SO₂C₂F₅)₂ concentrations. The electrolyte concentration was found to have a significant effect on the reactions occurring at the electrode. The poor cycleability of the electrodes in the low-concentration solutions was improved considerably by increasing the electrolyte concentration. Transmission electron microscopy (TEM) revealed that a high-concentration solution produces a thinner solid electrolyte interphase (SEI) on the electrodeposited lithium than a low-concentration solution, e.g., ∼35 nm in 1.28 mol kg⁻¹ vs. ∼20 nm in 3.27 mol kg⁻¹ solutions. Raman spectroscopy showed that the solvation number of lithium ions differed according to the electrolyte concentration. This suggests that the structure of solvated lithium ions is an important factor in suppressing dendritic lithium formation.     

A study of the photodeposition over Ti/TiO2 electrode for electrochemical detection of heavy metal ions

Here we reported that UV light irradiation can significantly enhance sensitivity of Ti/TiO₂ electrode for determination of trace heavy metal ions (such as Cu^2 +, Pb^2 + and Cd^2 +) owing to the photodeposition of metal ions on the surface of electrodes. The sensitivity of heavy metal ions can be selectively enhanced over the Ti/TiO₂ electrode, which is attributed to matching between potential of heavy metal ions and the position of the conduction band of TiO₂.     

In situ growth of polymer electrolytes on lithium ion electrode surfaces

Polyacrylonitrile (PAN) films were grown on glassy carbon, nickel foam and MnO₂ substrates by cathodic electropolymerisation of acrylonitrile in acetonitrile with tetrabutylammonium perchlorate (TBAP) as the supporting electrolyte. The electronic barrier properties of the films were confirmed by impedance spectroscopy of carbon |PAN| Hg cells while the ionic resistance of the films varied from 200 kΩ cm² in the dry state to 1.4 Ω cm² when plasticised with 1 M LiPF₆ in propylene carbonate. A galvanic cell was prepared by successive electrodepositions of MnO₂ and PAN on a carbon substrate, using liquid lithium amalgam as the top contact. The cell showed a stable open circuit potential and behaved normally under the galvanostatic intermittent titration technique (GITT).     

Lithium–manganese–nickel-oxide electrodes with integrated layered–spinel structures for lithium batteries

A series of lithium–manganese–nickel-oxide compositions that can be represented in three-component notation, xLi[Mn_1.5Ni_0.5]O₄ · (1 − x){Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂}, in which a spinel component, Li[Mn_1.5Ni_0.5]O₄, and two layered components, Li₂MnO₃ and Li(Mn_0.5Ni_0.5)O₂, are structurally integrated in a highly complex manner, have been evaluated as electrodes in lithium cells for x = 1, 0.75, 0.50, 0.25 and 0. In this series of compounds, which is defined by the Li[Mn_1.5Ni_0.5]O₄–{Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂} tie-line in the Li[Mn_1.5Ni_0.5]O₄–Li₂MnO₃–Li(Mn_0.5Ni_0.5)O₂ phase diagram, the Mn:Ni ratio in the spinel and the combined layered Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂ components is always 3:1. Powder X-ray diffraction patterns of the end members and the electrochemical profiles of cells with these electrodes are consistent with those expected for the spinel Li[Mn_1.5Ni_0.5]O₄ (x = 1) and for ‘composite’ Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂ layered electrode structures (x = 0). Electrodes with intermediate values of x exhibit both spinel and layered character and yield extremely high capacities, reaching more than 250 mA h/g with good cycling stability between 2.0 V and 4.95 V vs. Li° at a current rate of 0.1 mA/cm².     

Superabsorbent polymer binder for achieving MnO2 supercapacitors of greatly enhanced capacitance density

One common dilemma encountered in designing a supercapacitor electrode is that the specific capacitance (C_s) of the active material decreases significantly as the active-material loading (mass area^? 1) increases. As a result, the geometric capacitance density (GCD; Farad area^? 1) of the electrode does not scale up linearly but gradually levels off with increasing loading. For MnO₂ supercapacitors, this problem has been solved to a great extent by introducing a superabsorbent polymer (SAP) binder, namely polyacrylic acid (PAA), to form composite particles with MnO₂. Other than acting as a binder to bound together MnO₂ particles, the SAP is believed to facilitate distribution of electrolyte throughout the active layer owing to its electrolyte-absorbing and swelling behaviors. The C_s of MnO₂ remains almost unchanged as the oxide loading varies over a wide range (1.5–6.5 mg cm^? 2) of heavy active-material loading. In addition, putting PAA throughout the entire active layer helps to magnify the specific interaction between PAA and MnO₂ that is known to enhance the capacitance of individual MnO₂ particles. The success in combining both high C_s and high active-material loading results in GCD of ca. 1.8–1.4 F cm^? 2 even under very high current densities (ca. 35–260 mA cm^? 2 or 5–40 A g^? 1-MnO₂).     

Charge storage mechanism of MnO2 cathodes in Zn/MnO2 batteries using ionic liquid-based gel polymer electrolytes

Cathode reactions in Zn/MnO₂ batteries using aqueous electrolytes have been usually interpreted by the reduction of Mn^4 + to Mn^3 + while protons and/or cations penetrate inside the cathode. However, until now, the MnO₂ storage charge mechanism using a non-aqueous gel polymer electrolyte (GPE) has not been investigated. In this work, ionic liquid-based GPEs including BMIM Tf and ZnTf₂ have been employed in Zn/MnO₂ batteries. Different states of charge of MnO₂ cathodes used in Zn/IL-GPE/MnO₂ batteries have been analyzed by XPS and EDX techniques. XPS analysis showed that Mn^4 + is reduced during the discharge process at the same time as Zn^2 + cations are incorporated into the cathode. Besides, Zn^2 + cations insertion is accompanied by triflate anions.     

Insoluble metal hexacyanoferrates as supercapacitor electrodes

Nano-sized insoluble iron, cobalt and nickel hexacyanoferrates (Mhcf) were prepared by a simple co-precipitation method. The potential of using these materials for supercapacitor was examined by cyclic voltammogram and constant charge/discharge. Due to the different types of the second metal (M), the Mhcf electrodes showed different electrochemical capacitive performances. The specific discharge capacitances of Fehcf, Nihcf and Cohcf electrodes at the current density of 0.2 A g⁻¹ were 425 F g⁻¹, 574.7 F g⁻¹ and 261.56 F g⁻¹, respectively. Meanwhile, the Mhcf electrodes showed good cyclic performance.     

Intermediate phases during alkali metal intercalation in HfNCl

The mechanism of the chemical and electrochemical alkali metal intercalation reactions in β-HfNCl has been investigated through electrochemical potential spectroscopy (EPS), in-situ powder X-ray diffraction during electrochemical intercalation and room temperature chemical intercalation experiments. EPS experiments in lithium cells reveal the presence of a plateau, at 1.8 V vs. Li⁺/Li⁰ accounting for ca. 0.14 mol Li, that indicates the formation of a new intermediate phase, and then a gradual decrease of potential with composition that extends up to very high lithium contents (ca. 1.1 per formula), consistent with the formation of a solid solution. Sodium electrochemical intercalation experiments showed a relatively similar behaviour with a plateau at 1.4 V vs. Na⁺/Na⁰, corresponding to ca. 1.7 V vs. Li⁺/Li⁰. In-situ monitored powder X-ray diffraction electrochemical intercalation experiments showed that the electrolyte solvent (ethylene carbonate/dimethyl carbonate, EC/DMC or propylene carbonate, PC) co-intercalated with the alkaline atom. This leads to a large expansion of the interlayer spacing that reaches a value of 21.06 Å in the lithium co-intercalated phase with EC/DMC, Li_x(EC/DMC)_yHfNCl, and 22.01 Å in the sodium co-intercalated phase with PC, Na_x(PC)_yHfNCl. Chemical intercalation using naphthyl-sodium solutions in tetrahydrofuran (THF) leads to solvent-free, multiple-phase samples showing in different proportions the pristine and the superconducting stage 2 and stage 1 phases. The composition of the intercalated samples depends on the pristine sample, the concentration of the naphthyl-sodium solution, the ratio Na:HfNCl and the reaction time. Pristine samples exhibiting low lithium intercalation degree upon electrochemical reduction gave the second stage as the major phase when treated with short reaction times or using low Na:HfNCl ratios, coexisting either with the host or with the first stage phase, whereas stage 1 is obtained as the major phase from pristine samples showing high electrochemical capacities. The staging behaviour and the multiphase nature of these samples account for the wide superconducting transitions and the different critical temperatures observed in these superconductors.     

Choline biosensors based on a bi-electrocatalytic property of MnO2 nanoparticles modified electrodes to H2O2

An interesting mode of reactivity of MnO₂ nanoparticles modified electrode in the presence of H₂O₂ is reported. The MnO₂ nanoparticles modified electrodes show a bi-direction electrocatalytic ability toward the reduction/oxidation of H₂O₂. Based on this property, a choline biosensor was fabricated via a direct and facile electrochemical deposition of a biocomposite that was made of chitosan hydrogel, choline oxidase (ChOx) and MnO₂ nanoparticles onto a glassy carbon (GC) electrode. The biocomposite is homogeneous and easily prepared and provides a shelter for the enzyme to retain its bioactivity. The results of square wave voltammetry showed that the electrocatalytic reduction currents increased linearly with the increase of choline chloride concentration in the range of 1.0 × 10⁻⁵ –2.1 × 10⁻³ M and no obvious interference from ascorbic acid and uric acid was observed. Good reproducibility and stability were obtained. A possible reaction mechanism was proposed.     

Anomalous capacity and cycling stability of xLi2MnO3 · (1 − x)LiMO2 electrodes (M = Mn,Ni, Co) in lithium batteries at 50 °C

Transition metal oxides with composite xLi₂MnO₃ ·  (1 − x)LiMO₂ rocksalt structures (M = Mn, Ni, Co) are of interest as a new generation of cathode materials for high energy density lithium-ion batteries. After electrochemical activation to 4.6 or 4.8 V (vs. Li⁰) at 50 °C, xLi₂MnO₃ · (1 − x)LiMn_0.33Ni_0.33Co_0.33O₂ (x = 0.5, 0.7) electrodes deliver initial discharge capacities (>300 mAh/g) at a low current rate (0.05 mA/cm²) that exceed the theoretical values for lithiation back to the rocksalt stoichiometry (240–260 mAh/g), at least during the early charge/discharge cycles of the cells. Attention is drawn to previous reports of similar, but unaccounted and unexplained anomalous behavior of these types of electrode materials. Possible reasons for this anomalous capacity are suggested. Indications are that electrodes in which M = Mn, Ni and Co do not cycle with the same stability at 50 °C as those without cobalt.     

A microtubular all CNT gas diffusion electrode

We report a microtubular gas diffusion electrodes made of multi-walled carbon nanotubes (MWCNT). The electrodes were prepared by inside-out cake filtration of an aqueous MWCNT suspension onto a microfiltration hollow fiber (HF) membrane, followed by washing out the surfactant, drying and removal of the all CNT microtube from the HF membrane. Length, outer diameter, and wall thickness of the tubular electrodes are: up to 44 cm, ~ 1.7 mm and 275 μm, respectively. The BET surface area is 200 m²/g with a porosity of 48–67% and an electrical conductivity of ~ 20 S/cm. Application of this microtubular Gas Diffusion Electrodes (GDE) was studied for the oxygen reduction reaction (ORR) in divided and undivided electrochemical cells. Oxygen supply into the lumen of the tubular electrodes resulted in much higher current densities for ORR than in experiments where the electrolyte was saturated by bubbling with pure oxygen. Within the 0.25–1.0 bar pressure (gauge) region, higher ORR rates were achieved at lower pressure. We also show that H₂O₂ production is possible using the new GDE. We propose to use such novel electrodes for the fabrication of tubular electrochemical reactors, e.g. fuel cells, H₂O₂ generators, CO₂ reduction and other processes that involve GDE application.     

Transparent electrochemical capacitor based on electrodeposited MnO2 thin film electrodes and gel-type electrolyte

A new concept for a transparent electrochemical capacitor was demonstrated. It includes two MnO₂ electrodes separated with a gel electrolyte, making the whole device less than 1 mm thick and transparent. Preliminary electrochemical experiments revealed a capacitance of 2 mF cm^?2 over more than 200 cycles. The device exhibited only a small absorbance change during repeated cycling.     

Electrospun porous SnO2 nanotubes as high capacity anode materials for lithium ion batteries

Porous SnO₂ nanotubes were prepared via electrospinning followed by calcination in air. As anode materials for lithium ion batteries, the porous nanotubes delivered a high discharge capacity of 807 mAh g^? 1 after 50 cycles. Even after cycled at high rates, the electrode still retained a high fraction of its theoretical capacity. Such excellent performances of porous SnO₂ nanotubes could be attributed to the porous and hollow structure which facilitated liquid electrolyte diffusion into the bulk materials and buffered large volume changes during lithium ions insertion/extraction. Furthermore, the nanoparticles of nanotubes provided the shorter diffusion length for lithium ions insertion which benefited in retaining the structural stability and good rate performance. Our results demonstrated that this simple method could be extended for the synthesis of porous metal oxide nanotubes with high performances in the applications of lithium ion batteries and other fields.     

Tunable lithium storage properties of metal lithium titanates by stoichiometric modulation

A simple stoichiometric modulation of Na_2 − 2xSr_xLi₂Ti₆O₁₄ was developed to achieve tunable electrochemical properties of the material. The concept was confirmed experimentally and theoretically using density functional theory (DFT) calculations. Both the operating potential and the amount of reversibly intercalated lithium ions were manipulated by simply changing the Na/Sr ratio. These unique characteristics originated from a gradual change in the electron density on the Ti atoms and the extra lithium insertion sites at SrLi₂Ti₆O₁₄. As a promising anode material for lithium-ion batteries, Na_2 − 2xSr_xLi₂Ti₆O₁₄ and its tunable electrochemical properties have significant importance in terms of the development of tailored electrodes with desirable electrochemical performance.     

Flexible asymmetric supercapacitor based on MnO2 honeycomb structure

By controlling the electroplating time of solution containing Mn(Ac)₂, the MnO₂ nanosheets were self-assembled to the honeycomb structure and showed an excellent electrochemical performance in 1 mol/L Na₂SO₄ electrolyte. Via pairing with activated carbon as negative electrode, the capacitor could deliver a maximum energy density of 43.84 Wh/kg and a maximum power density of 6.62 kW/kg.     

A hierarchical micro/nanostructured 0.5Li2MnO3·0.5LiMn0.4Ni0.3Co0.3O2 material synthesized by solvothermal route as high rate cathode of lithium ion battery

A hierarchical micro/nanostructured Li-rich layered 0.5Li₂MnO₃·0.5LiMn_0.4Ni_0.3Co_0.3O₂ (H-LMNCO) material is prepared for the first time through the development of a solvothermal method, and served as cathode of lithium ion batteries. Electrochemical tests indicate that the H-LMNCO exhibits both a high reversible capacity and an excellent rate capability. The reversible discharge capacity of the H-LMNCO has been measured as high as 300.1 mAh·g^− 1 at 0.2 C rate. When the rate is increased to 10 C, the discharge capacity could still maintain a high value of 163.3 mAh·g^− 1. The results demonstrate that the developed solvothermal route is a novel synthesis strategy of preparing high rate performance Li-rich layered cathode material for lithium ion batteries.     

A binder-free thin film anode composed of Co2 +-intercalated buserite grown on carbon cloth for oxygen evolution reaction

We present a binder-free catalytic anode for highly efficient and stable oxygen evolution reaction in alkaline media. The catalyst consists of a thin film of buserite-type layered manganese dioxide (MnO₂) intercalated with Co^2 + ions, resulting from electrodeposition of the layered MnO₂ film with tetrabutylammonium (Bu₄N⁺) ions on a carbon cloth, followed by ion-exchange of the initially incorporated Bu₄N⁺ with Co^2 + in solution. The electrode is capable to produce a current density of 10 mA cm^− 2 at an overpotential (η) of 377 mV with a Tafel slope of 48 mV dec^− 1, much superior to the layered MnO₂ without Co^2 +.