铁掺杂纳米ZnO室温脱硫剂的硫化及再生研究

为降低纳米ZnO脱硫剂的应用成本及避免对环境产生二次污染,本文对均匀沉淀法制备的铁掺杂纳米ZnO脱硫剂(FZ5.0)进行了硫化和再生循环试验研究,并利用XRD、XPS和TEM等表征手段对FZ5.0的硫化及再生前后的结构进行了分析。结果表明,脱硫剂表面存在3种脱硫产物,HS、S形成的吸附配合物和ZnS,370 ℃时可直接通入空气进行连续5次再生。经过第1次再生后纳米脱硫剂结构便趋于稳定,并在后面的循环过程中表现出较稳定的脱硫活性,但与新鲜脱硫剂相比较,其脱硫活性是新鲜脱硫剂的50%左右。再生过程中主要产物为SO₂气体,还有少量的硫酸盐生成,再生后样品的晶粒尺寸、形貌变化不大,但比表面积和孔容变化明显,这也是导致脱硫活性下降的主要原因。     

Sb2S3纳米粒子修饰ZnO纳米片微纳分级结构的光电化学性能

采用恒电位方法,选择氯化钾和乙二胺(EDA)为添加剂,在氧化铟锡(ITO)导电玻璃上制备了高度有序的ZnO纳米片阵列,通过二次电沉积得到了ZnO纳米片上生长纳米棒的微纳分级结构.利用化学浴沉积法在ZnO基底上沉积Sb₂S₃纳米粒子制备出了Sb₂S₃/ZnO纳米片壳核结构和Sb₂S₃/ZnO微纳分级壳核结构.利用扫描电子显微镜(SEM)、X射线衍射(XRD)、紫外-可见(UV-Vis)吸收光谱、瞬态光电流等对其形貌、结构组成和光电化学性能进行了表征和分析.结果表明, Sb₂S₃/ZnO纳米片上生长纳米棒分级壳核结构的光电流明显高于Sb₂S₃/ZnO纳米片壳核结构.在Sb₂S₃/ZnO纳米片壳核结构和Sb₂S₃/ZnO微纳分级壳核结构的基础上旋涂一层P3HT薄膜形成P3HT/Sb₂S₃/ZnO复合结构,以上述复合结构薄膜为光活性层组装成杂化太阳电池,其中, P3HT/Sb₂S₃/ZnO分级壳核结构杂化太阳电池的能量转换效率最高,达到了0.81%.     

CdS:Mn/ZnS核壳结构纳米晶体的场致发光性质

锰掺杂的核壳结构CdS:Mn/ZnS纳米晶体由胶体化学方法制备,并将该纳米晶体所形成的薄膜夹在两层Ta₂O₅薄膜中间,形成交流薄膜电致发光器件.该器件的电致发光强度随着环境温度的升高呈现先增强后减小的变化规律,并且Mn杂质的位置会影响其电致发光谱.     

氧化石墨烯浓度对还原氧化石墨烯/ZnS电化学性能的影响

以氧化石墨烯(GO)、乙酸锌(Zn(CH₃COO)₂)和硫脲为原料,采用水热法成功制备了还原氧化石墨烯/ZnS(rGO/ZnS)复合材料,并将该材料用作锂离子电池负极。高导电性的 rGO可以为锂离子和电子的传输提供有效的路径,ZnS可以提供较高的理论比容量。rGO/ZnS复合材料在rGO与纳米级高度分散的类球形ZnS颗粒协同作用下展现了较好的嵌锂容量和循环性能。当GO质量浓度为2 mg·mL^-1时制备的rGO/ZnS复合材料的倍率性能最好,循环稳定性最佳。     

氧化石墨烯浓度对还原氧化石墨烯/ZnS电化学性能的影响

以氧化石墨烯(GO)、乙酸锌(Zn(CH₃COO)₂)和硫脲为原料,采用水热法成功制备了还原氧化石墨烯/ZnS(rGO/ZnS)复合材料,并将该材料用作锂离子电池负极。高导电性的 rGO可以为锂离子和电子的传输提供有效的路径,ZnS可以提供较高的理论比容量。rGO/ZnS复合材料在rGO与纳米级高度分散的类球形ZnS颗粒协同作用下展现了较好的嵌锂容量和循环性能。当GO质量浓度为2 mg·mL^-1时制备的rGO/ZnS复合材料的倍率性能最好,循环稳定性最佳。     

单分散SnO2中空微纳米球的制备和性质

模板法是制备无机中空微纳米球的重要方法之一. 本文以苯乙烯为单体, 通过乳液聚合得到粒径约为620 nm的单分散聚苯乙烯(PS)微球. 以磺化后的聚苯乙烯(PSS)微球为模板, 利用阴阳离子静电吸附作用, 将PSS与前驱体SnSO₄中的Sn²⁺结合. 通过Sn²⁺在乙醇-水介质中的水解作用得到核-壳复合结构, 再经高温煅烧, 得到SnO₂中空微纳米球. 实验对前驱体的浓度、表面活性剂的用量、反应时间及模板选择等方面做了研究,通过扫描电镜(SEM)、X 射线衍射(XRD)、红外(IR) 光谱、热重分析(TGA)、H₂ 程序升温还原(H₂-TPR)、Brunauer-Emmett-Teller (BET)比表面积等技术深入探究SnO₂中空微纳米球的结构, 并对比中空SnO₂与实心粒子的氧化还原特性. BET和H₂-TPR显示将SnO₂制备成微纳米空心球后其比表面积增大, 表面氧空位明显增多, 氧化活性明显提高. 从IR 及XRD推断核-壳结构形成机理, 进而优化出简单合理的实验方案, 获得表面光滑、结构致密, 包覆厚度可控的SnO₂中空微纳米球.     

P3HT/CdS/TiO2/ZnO一维有序核壳式纳米棒阵列的构制及其在杂化太阳电池中的应用研究

采用恒电位法在铟锡氧化物导电玻璃(ITO)上制备了高度有序一维ZnO纳米棒阵列,将ZnO纳米棒阵列在TiO2溶胶中采用提拉法制备出了一维TiO2/ZnO核壳式纳米棒阵列.在一维TiO2/ZnO核壳式纳米棒阵列上电沉积CdS纳米晶得到一维CdS/TiO2/ZnO核壳式纳米棒阵列,然后在一维CdS/TiO2/ZnO核壳式纳米棒阵列上电沉积聚3-己基噻吩(P3HT)薄膜得到P3HT/CdS/TiO2/ZnO核壳式纳米结构薄膜.以该纳米结构薄膜电极为光阳极制备出新型纳米结构杂化太阳电池,研究了该类电池的光电转换性能,初步探讨了该类电池的工作机理.     

硫化亚铜对电极在量子点敏化太阳电池中的应用

报道了一种基于硫族金属复合物N₄H₉Cu₇S₄前驱体溶液制备硫化亚铜对电极的新方法. 分别制备了TiO₂纳米颗粒多孔薄膜和TiO₂纳米棒阵列结构的光阳极, 并在此基础上研究了基于硫化亚铜对电极的CdS/CdSe量子点敏化太阳电池的光电性能, 同时结合电化学阻抗技术考察了硫化亚铜对电极的催化性能. 结果表明: 与铂电极相比, 本方法制备的硫化亚铜电极对多硫电解质具有更高的催化活性, 所组装的CdS/CdSe量子点敏化太阳电池具有更优的光伏性能.     

稀碱溶液中水热法制备柔性TiO2纳米须薄膜的生长机制及表征

以柔性不锈钢基底上经磁控溅射沉积的钛膜为钛源, 在1 mol·L^-1的低浓度NaOH溶液中水热法制备了朝基底上方取向生长的大长径比柔性TiO₂纳米须薄膜, 考察了钛膜沉积条件对纳米须薄膜的影响, 系统研究了水热反应条件对薄膜生长过程的影响及TiO₂纳米须薄膜的形成机制. 通过场发射扫描电镜(FESEM)、X射线能谱仪(EDS)、高分辨透射电子显微镜(HRTEM)、X射线衍射仪(XRD)等对样品进行了表征. 结果表明, 与室温沉积的钛膜相比, 600 ℃下沉积的钛膜水热后得到的纳米线薄膜与基底的附着力更好. 所得TiO₂纳米须为单晶锐钛矿, 经由Na₂Ti₂O₄(OH)₂、H₂Ti₂O₅·H₂O转变而来. 纳米须形成于水热阶段, 平行于Na₂Ti₂O₄(OH)₂的(100)晶面择优取向生长, 纳米须经历了纳米片→纳米线束→纳米线的裂解生长过程. 朝基底上方取向生长的纳米须薄膜的形成是低浓度NaOH溶液与较高水热温度(220 ℃)协同作用的结果. 进一步在Na₂SO₄溶液中研究了薄膜电极的光电化学性能, 结果表明, TiO₂纳米须薄膜的光电性能明显优于零维纳米颗粒薄膜和二维纳米片薄膜, 显示了良好的应用前景.     

CdS:Mn/ZnS核壳结构纳米晶体的场致发光性质

锰掺杂的核壳结构CdS:Mn/ZnS纳米晶体由胶体化学方法制备,并将该纳米晶体所形成的薄膜夹在两层Ta₂O₅薄膜中间,形成交流薄膜电致发光器件。该器件的电致发光强度随着环境温度的升高呈现先增强后减小的变化规律,并且Mn杂质的位置会影响其电致发光谱。     

Detailed investigations of ZnO photoelectrodes preparation for dye sensitized solar cells

Wurtzite ZnO hexagonal nanopyramids were successfully synthesized in the liquid phase from homogeneous methanolic solutions of zinc acetate and tetramethylammonium hydroxide at an excess of zinc ions. The formation and properties of the nanocrystals were examined as a function of synthesis conditions. No significant influence of the [Zn(2+)]/[OH(-)] ratio was noticed on the final particle size, in spite of increased amounts of OH(-) ions, which tend to accelerate the particle nucleation and growth. Nevertheless, the reactant concentration ratio influences the surface properties of the ZnO nanocrystals. Mesoporous ZnO films were prepared by doctor blading ethanolic pastes containing ZnO nanoparticles and ethyl cellulose onto FTO conductive glass substrate followed by calcination. Additionally, the influence of a plasticizer (triacetin)-used during the paste preparation-on the film quality was investigated. A higher content of ZnO nanoparticles and plasticizer in the pastes improved the film quality. Four different temperatures (i.e., 400, 425, 450, and 475 °C) were used for the film calcination and their influence on the structural properties of the films was characterized. In principle, increasing the calcination temperature goes hand in hand with an increase of particle size, as well as the pore diameter and reduction of the surface area. Suitable mesoporous films were employed as photoanodes in dye sensitized solar cells (DSSCs). In order to assess the effect of the varied parameters on complete DSSC devices-using cis-diisothiocyanato-bis(2,2'-bipyridyl-4,4'-dicarboxylato) ruthenium(II)bis(tetrabutylammonium (N719) as a sensitizer-incident photon to current efficiency (IPCE) and current voltage measurements were carried out. The IPCE measurements confirmed photoinduced electron injection from the dye, reaching IPCE values up to 76%. Furthermore, current-voltage characteristics of complete cells emphasized the importance of the proper preparation methods and temperatures. These features are important assets for the preparation of nanocrystalline ZnO based photoelectrodes and for improving the DSSC performance.     

Reconstruction of the (001) surface of TiO2 nanosheets induced by the fluorine-surfactant removal process under UV-irradiation for dye-sensitized solar cells

The champion dye-sensitized solar cells (DSSCs) based on TiO(2) nanoparticles nearly reach the limit of photo-current density using the black dye or zinc porphyrin dye as sensitizer. However, the way to make ordinary DSSCs more efficient as well as to understand the mechanism is still essential. Here we present an elegant UV irradiation treatment of TiO(2) nanosheets to enhance the performance of DSSCs based on the TiO(2) nanosheets via room temperature removal of inorganic surfactants and reconstruction of the (001) surface of TiO(2) nanosheets, killing two birds with one stone. UV irradiation was utilized to remove the fluorine-surfactant on the surface of anatase TiO(2) nanosheets with a high percentage of exposed {001} facets which were synthesized with the aid of hydrofluoric acid. The nanosheets treated with UV irradiation for 40 min had the advantage of improving the photoelectric conversion efficiency of DSSCs by 17.6%, compared to that without UV treatment when they were introduced into DSSCs as photoanode materials. The improved efficiency was ascribed to more dye adsorption. A theoretical calculation proposed that UV irradiation induced microfaceted steps on the TiO(2) surface by two domain (1 × 4) reconstruction after UV irradiating the (1 × 1) (001) surface. The microfaceted steps increase the active surface area of the TiO(2) nanosheets by increasing the exposure of titanium atoms and engendering active sites.     

ZnO hierarchical structures for efficient quasi-solid dye-sensitized solar cells

We report a direct precipitation method for mass production of ZnO microflowers (MFs) containing hierarchical structures. The ZnO MFs are constructed by interlaced single crystalline and porous nanosheets which are ideal photoanode material for dye-sensitized solar cells (DSCs) because the MFs can largely improve the energy harvesting performance and the efficiency of DSCs. Compared with other forms of nano-sized structures, the novel hierarchical structures show obvious advantages in DSC application because of their large surface area for dye-loading, good light scattering efficiency and excellent electrical transport property. The quasi-solid state DSCs fabricated with the MF hierarchical structures exhibited an efficiency of 4.12%, much higher than that of ZnO nanoparticle-based DSCs, indicating a great potential for the development of highly-efficient quasi-solid DSCs.     

二氧化钛多孔纳米片在染料敏化太阳电池中的应用

运用连续吸附反应法和化学腐蚀-沉积法,用ZnO/FTO(氟掺杂氧化锡)多孔纳米片为模板,制备了TiO2/FTO多孔纳米片。研究了吸附次数对形貌、光散射性能和染料敏化太阳电池性能的影响。最佳吸附次数为30,由此得到的太阳能电池的效率、短路电流密度Jsc、开路电压Voc和填充因子FF分别为:5.57%、9.26 mA·cm-2、0.835 V和72.04%。这个效率略高于P25(5.32%),但远高于ZnO(2.41%)。     

二氧化钛多孔纳米片在染料敏化太阳电池中的应用

运用连续吸附反应法和化学腐蚀-沉积法,用ZnO/FTO（氟掺杂氧化锡）多孔纳米片为模板,制备了TiO₂/FTO多孔纳米片。研究了吸附次数对形貌、光散射性能和染料敏化太阳电池性能的影响。最佳吸附次数为30,由此得到的太阳能电池的效率、短路电流密度J_sc、开路电压V_oc和填充因子FF分别为：5.57%、9.26mA·cm^-2、0.835V和72.04%。这个效率略高于P₂₅（5.32%）,但远高于ZnO（2.41%）。     

Morphology evolution of ZnO thin films from aqueous solutions and their application to solar cells

This paper reports a reproducible low-temperature solution-based process for the preparation of ZnO films of nanorod arrays and their application to dye-sensitized solar cells (DSSCs). A two-step approach was employed for the epitaxial growth of ZnO. We began with the preparation of a (002)-oriented ZnO seed layer by the electrochemical deposition method. After the treatment the substrate was soaked in an aqueous solution containing ZnCl2 and complex agents. A large-scale fabrication of ZnO nanorod arrays on transparent conductive oxides has been achieved after soaking at 95 degrees C for 1-48 h. The as-deposited ZnO film has a large surface area, therefore permitting a great amount of dye loading. The individually separated nanorod forms a linear nanoroad which should show more effective electron transportation than that in the film derived from ZnO powders. The DSSCs using these ZnO films as photoelectrodes show a conversion efficiency of about 0.6% at AM1.5.     

A Combinatorial Approach for Optimization of Oxygen Evolution Catalyst Loading on Mo‐doped BiVO4 Photoanodes

The incident photon to current efficiency (IPCE) of a photoactive surface strongly depends on the loading and thickness of the active materials. We present a combinatorial approach based on an optical scanning droplet cell for simultaneous deposition and systematic characterization of co‐catalysts for the oxygen evolution reaction (OER) on Mo‐doped BiVO₄ (Mo?BiVO₄) photoanodes electrochemically pre‐deposited on transparent conductive FTO substrates. The loading and photoelectrochemical characterization of 10 different OER co‐catalysts deposited by three different deposition techniques on FTO‐supported Mo?BiVO₄ were investigated aiming at determination of the suitable deposition parameters affording the highest enhancement of photoelectrochemical oxygen evolution for the different OER/Mo?BiVO₄ films. A comparison of the photoelectrochemical performance of films of various OER co‐catalyst deposited on FTO‐supported Mo?BiVO₄ by electrodeposition, photo‐assisted electrodeposition and photodeposition revealed the necessity of a material specific optimization with respect to co‐catalyst loading and deposition technique to achieve optimal IPCE for each co‐catalysts.     

Efficiency improvement of flexible dye-sensitized solar cells by introducing mesoporous TiO2 microsphere

Mesoporous TiO2microsphere(MTM)was synthesized via a simple solution route and then mixed with commercial TiO2(P25)to form highly homogeneous and stable TiO2colloid by simple hydrothermal treatment.The TiO2colloid was coated onto the plastic conductive substrate to prepare mesoporous TiO2film for flexible dye-sensitized solar cells(DSSCs)by low-temperature heat treatment.The influence of MTM content on the physicochemical properties of the flexible TiO2film was characterized by scanning electron microscope,transmission electron microscopy,X-ray diffraction,energy-dispersive X-ray spectrometer,N2adsorption-desorption isotherms,UV–vis absorption and diffuse reflectance spectra.It is revealed that with increasing the MTM content,the dye-loading capability of TiO2film and light-harvesting efficiency of flexible DSSCs are improved due to MTM having high surface area and acting as a light scattering center,respectively,resulting in the enhancement of photocurrent of flexible DSSCs.However,more and larger cracks having negative effect on the performances of flexible DSSCs are formed simultaneously.Under the optimal condition with MTM content of 20%,a flexible DSSC with overall light-to-electric energy conversion efficiency of 2.74%is achieved under a simulated solar light irradiation of 100 mW cm 2(AM 1.5),with 26%improvement in comparison with DSSCs based on P25 alone.     

金属有机框架在染料敏化太阳能电池中的应用

为了获得高效率的染料敏化太阳能电池,其光阳极应该具有大的比表面积,以吸附足量的染料,获得很强的光捕获能力.从这个角度而言,将具有很大比表面积的金属有机框架材料引入到染料敏化太阳能电池的体系中,无疑是一种有益的探索.本文简介了金属有机框架材料在光伏领域的应用,并重点介绍了我们课题组在利用金属有机框架材料方面进行的一些探索,包括光阳极薄膜的处理、利用金属有机框架材料作为前驱体制备光阳极材料和光散射层.最后,本文对金属有机框架材料应用于染料敏化太阳能电池中的局限性及前景做了简要的展望.     

Improved conversion efficiency in dye-sensitized solar cells based on electrospun Al-doped ZnO nanofiber electrodes prepared by seed layer treatment

The application of electrospun nanofibers in electronic devices is limited due to their poor adhesion to conductive substrates. To improve this, a seed layer (SD) is introduced on the FTO substrate before the deposition of the electrospun composite nanofibers. This facilitates the release of interfacial tensile stress during calcination and enhances the interfacial adhesion of the AZO nanofiber films with the FTO substrate. Dye-sensitized solar cells (DSSC) based on these AZO nanofiber photoelectrodes have been fabricated and investigated. An energy conversion efficiency (η) of 0.54-0.55% has been obtained under irradiation of AM 1.5 simulated sunlight (100 mW/cm²), indicating a massive improvement of η in the AZO nanofiber film DSSCs after SD-treatment of the FTO substrate as compared to those with no treatment. The SD-treatment has been demonstrated to be a simple and facile method to solve the problem of poor adhesion between electrospun nanofibers and the conductive substrate.