CO2在氨基改性MIL-101(Cr)中吸附的分子模拟

采用实验与分子模拟结合的方法研究298 K下CO₂在氨基改性得到的MIL-101（Cr）-NH₂和MIL-101（Cr）-ED（ED：乙二胺）上的吸附性能。比较MIL-101（Cr）、MIL-101（Cr）-NH₂和MIL-101（Cr）-ED的吸附等温线与吸附热的结果,表明采用直接合成改性法得到的MIL-101（Cr）-NH₂比采用合成后再改性得到的MIL-101（Cr）-ED有更高的CO₂吸附容量。进一步比较密度分布图和径向密度分布曲线,分析CO₂在氨基改性MIL-101（Cr）中的吸附位,表明在低压下CO₂首先吸附在MIL-101（Cr）微孔的超级四面体中,随着吸附压力的增大逐渐填充到更大的孔中。氨基的存在增加了CO₂的吸附位点,使MIL-101（Cr）-NH₂具有较高CO₂吸附容量;同时MIL-101（Cr）-ED中的ED分子的存在增加了CO₂的吸附位点,使MIL-101（Cr）-ED也具有较高CO₂吸附容量;但是MIL-101（Cr）-ED中的ED分子占据了MIL-101（Cr）中Cr的吸附位点,使Cr对CO₂的吸附强度减弱,同时可吸附位点少于MIL-101（Cr）-NH₂,导致其对CO₂的吸附容量少于MIL-101（Cr）-NH₂。     

CO2在氨基改性MIL-101(Cr)中吸附的分子模拟

采用实验与分子模拟结合的方法研究298 K下CO_2在氨基改性得到的MIL-101(Cr)-NH_2和MIL-101(Cr)-ED(ED:乙二胺)上的吸附性能。比较MIL-101(Cr)、MIL-101(Cr)-NH_2和MIL-101(Cr)-ED的吸附等温线与吸附热的结果,表明采用直接合成改性法得到的MIL-101(Cr)-NH_2比采用合成后再改性得到的MIL-101(Cr)-ED有更高的CO_2吸附容量。进一步比较密度分布图和径向密度分布曲线,分析CO_2在氨基改性MIL-101(Cr)中的吸附位,表明在低压下CO_2首先吸附在MIL-101(Cr)微孔的超级四面体中,随着吸附压力的增大逐渐填充到更大的孔中。氨基的存在增加了CO_2的吸附位点,使MIL-101(Cr)-NH_2具有较高CO_2吸附容量;同时MIL-101(Cr)-ED中的ED分子的存在增加了CO_2的吸附位点,使MIL-101(Cr)-ED也具有较高CO_2吸附容量;但是MIL-101(Cr)-ED中的ED分子占据了MIL-101(Cr)中Cr的吸附位点,使Cr对CO_2的吸附强度减弱,同时可吸附位点少于MIL-101(Cr)-NH_2,导致其对CO_2的吸附容量少于MIL-101(Cr)-NH_2。     

Hydration behavior of mixed ligand chromium complexes. Part I: partial molar volumes and partial molar adiabatic compressibilities of oxalato and mixed oxalato — Ethylxanthato chromate(III) complexes

Densities and ultrasonic velocities in aqueous solutions of cis-K[Cr(ox)₂(H₂O)₂], K₃[Cr(ox)₃] and KSSCOC₂H₅ and a mixed ligand complex K₂[Cr(ox)₂SSCOC₂H₅], where SSCOC₂H₅ is the ethylxanthate ligand, have been measured at 25, 35 and 45°C. Limiting partial molar volumes, partial molar adiabatic compressibilities and hydration numbers of the complex salts as well as of the ligand have been calculated. The implication of the findings are discussed.     

Thermodynamic Model for the Solubility of Cr(OH)3(am) in Concentrated NaOH and NaOH–NaNO3 Solutions

The main objective of this study was to develop a thermodynamic model for predicting Cr(III) behavior in concentrated NaOH and in mixed NaOH–NaNO₃ solutions for application to developing effective caustic leaching strategies for high-level nuclear waste sludges. To meet this objective, the solubility of Cr(OH)₃(am) was measured in 0.003 to 10.5 m NaOH, 3.0 m NaOH with NaNO₃ varying from 0.1 to 7.5 m, and 4.6 m NaNO₃ with NaOH varying from 0.1 to 3.5 m at room temperature (22 ± 2°C). A combination of techniques, X-ray absorption spectroscopy (XAS) and absorptive stripping voltammetry analyses, were used to determine the oxidation state and nature of aqueous Cr. A thermodynamic model, based on the Pitzer equations, was developed from the solubility measurements to account for dramatic increases in aqueous Cr with increases in NaOH concentration. The model includes only two aqueous Cr species, Cr(OH) ₄ ^– and Cr₂O₂(OH) ₄ ^– (although the possible presence of a small percentage of higher oligomers at >5.0 m NaOH cannot be discounted) and their ion–interaction parameters with Na⁺. The logarithms of the equilibrium constants for the reactions involving Cr(OH) ₄ ^– [Cr(OH)₃(am) + OH^– Cr(OH) ₄ ^– ] and Cr₂O₂(OH) ₄ ^2– [2Cr(OH)₃(am) + 2OH^– Cr₂O₂(OH) ₄ ^2– + 2H₂O] were determined to be –4.36 ± 0.24 and –5.24 ± 0.24, respectively. This model was further tested and provided close agreement between the observed Cr concentrations in equilibrium with Cr(OH)₃(am) in mixed NaOH–NaNO₃ solutions and with high-level tank sludges leached with and primarily containing NaOH as the major electrolyte.     

Application of the Composite of TiO2 Nanoparticles and Carbon Nanotubes to the Photo-Reduction of Cr(VI) in Water

The composite of carboxyl-modified multi-walled carbon nanotubes (MWNT-COOH) and TiO₂ nanoparticles was prepared in a solvothermal process. The x-ray diffraction (XRD), transmission electron microscope (TEM) and UV-vis spectrum were used to characterize the products. The results showed that the MWNT-COOH was dispersed uniformly in the composite and coated with TiO₂ nanoparticles. The photo-reduction of Cr(VI) to Cr(III) in water catalyzed by the composite was investigated at room temperature. The photocatalytic activity of the composite markedly increased by a factor of approximately 2.2 in comparison with pure TiO₂ (P25). Furthermore, the mechanism of the photocatalytic activity enhancement of the MWNT-COOH/TiO₂ nanoparticles composite for the photo-reduction of Cr(VI) was discussed.     

铈铬比例对CeO2-CrOx复合氧化物催化剂上1,2-二氯乙烷催化氧化性能的影响

采用共沉淀法制备了不同铈铬比例的CeO₂-CrO_x复合氧化物(Ce/Cr 摩尔比分别为9/1、4/1、2/1、1/1、1/2、1/4、1/8)以及单纯的CeO₂和Cr₂O₃, 并研究了各催化剂对1,2-二氯乙烷(DCE)的催化氧化性能. 结果表明,相较于单纯的CeO₂, 不同铈铬比例的复合氧化物催化剂对DCE的催化氧化活性有明显提高, 其中Ce/Cr 摩尔比为2/1的CeO₂-CrO_x复合氧化物上DCE的氧化活性最好, 且只有极微量的含氯等副产物产生; 随着Ce/Cr 摩尔比减小, 对HCl的选择性有下降的趋势. 通过X射线衍射(XRD)、N₂吸附/脱附(BET)、紫外拉曼(UV-Raman)光谱、H₂程序升温还原(H₂-TPR)、NH₃程序升温脱附(NH₃-TPD)等实验技术, 研究了铈铬比例对铈铬复合氧化物的物理化学性质的影响. 结果表明, 适当比例Ce-Cr的复合, 形成了结构较稳定的Ce-Cr-O固溶体, 提高了催化剂活性氧物种的流动性, 催化剂表面酸量及强弱酸比例, 从而有利于DCE的吸附活化, 进一步脱氯降解以及深度氧化.     

Photocatalytic Reduction of Cr (VI) over g-C3N4 Photocatalysts Synthesized by Different Precursors

Graphitic carbon nitride (g-C₃N₄) photocatalysts were synthesized via a one-step pyrolysis process using melamine, dicyandiamide, thiourea, and urea as precursors. The obtained g-C₃N₄ materials exhibited a significantly different performance for the photocatalytic reduction of Cr(VI) under white light irradiation, which is attributed to the altered structure and occupancies surface groups. The urea-derived g-C₃N₄ with nanosheet morphology, large specific surface area, and high occupancies of surface amine groups exhibited superior photocatalytic activity. The nanosheet morphology and large surface area facilitated the separation and transmission of charge, while the high occupancies of surface amine groups promoted the formation of hydrogen adsorption atomic centers which were beneficial to Cr(VI) reduction. Moreover, the possible reduction pathway of Cr(VI) to Cr(III) over the urea-derived g-C₃N₄ was proposed and the reduction process was mainly initiated by a direct reduction of photogenerated electrons.     

Preparation, structural and magnetic characterization of DyCrMnO5

The title compound has been first synthesized by a citrate technique followed by thermal treatments under moderate oxygen pressure conditions, and characterized by X-ray and neutron powder diffraction (NPD) and magnetization measurements. The crystal structure of DyCrMnO₅ has been refined from NPD data in the space group Pbam; a=7.2617(6) Å, b=8.5161(6) Å, and c=5.7126(5) Å at 295 K. This oxide is isostructural with RMn₂O₅ oxides (R=rare earths) and it contains infinite chains of (Cr, Mn)⁴⁺O₆ octahedra-sharing edges, linked together by (Mn, Cr)³⁺O₅ pyramids and DyO₈ units. The high degree of antisite disordering exhibited by DyCrMnO₅ is noteworthy. The octahedral positions are occupied by roughly 50% of Mn and Cr cations, and the pyramidal groups contain two thirds of Mn and one third of Cr cations. We assume that Mn and Cr cations at the octahedral positions exhibit a tetravalent oxidation state, whereas the metals at the pyramidal positions are trivalent, in order to preserve the electroneutrality of this oxide. The susceptibility vs temperature curve of DyCrMnO₅ does not suggest the establishment of a long-range magnetic structure even at low temperatures; the NPD technique does not provide any signal of magnetic ordering, since the reflections do not show any magnetic contribution.     

New mixed-valence chromium structure type: NH4Cr(CrO4)2

Synthesis and crystal structure of a new structure type of mixed Cr(III)/Cr(VI) chromates is reported. NH₄Cr(CrO₄)₂ was prepared from CrO₃ in the presence of (NH₄)₂Ce(NO₃)₆. Since this is the first preparation of mixed valence ternary chromium oxides from aqueous solution, a reaction pathway for this synthesis is suggested. The crystal structure of NH₄Cr(CrO₄)₂ has been determined from three-dimensional X-ray data collected at low temperature, 173 K. The structure belongs to the orthorhombic space group Pnma, with a=14.5206(10), b=5.4826(4), and Z=4. The title compound consists of corner-sharing chromium(III) octahedra and chromium(VI) tetrahedra forming a three-dimensional network with the composition [Cr(CrO₄)₂]_n^n-, containing channels in which zigzag rows of ammonium ions balance the net charge.     

First-principles study of O2 adsorption and dissociation on the CuCr2O4 (100) surface

The adsorption and dissociation of molecular oxygen on spinel CuCr₂O₄ (100) surface were carried out by first-principles calculations based on density functional theory (DFT). The calculated results indicate that the Cr site is most favorable for atomic oxygen adsorption, with an adsorption energy of 402.8 kJ/mol. For molecular oxygen adsorption, there are three types of favorable interaction modes: O₂ forms bonds with the Cu site or O₂ binds to two Cr sites or O₂ interacts with both Cu and Cr sites simultaneously. The lowest activation energy (E_a = 35.4 kJ/mol) was found through exploring possible reaction pathways for O₂ dissociation. The relationship between E_a and reaction enthalpy (ΔH) for O₂ dissociation adsorption reactions fits Brønsted-Evans-Polanyi (BEP) behavior.     

Cr3+在不同基质Y3Ga5O12或Ga2O3中的荧光特性

以Ga_2O_3、Y_2O_3、Cr(NO_3)_3·9H_2O为原料,柠檬酸为配位剂,通过溶胶-凝胶高温固相合成法制备出Ga_(2-2x)O_3∶2xCr~(3+)(Ga_2O_3∶xCr)与Y_3Ga_(5-5x)O_(12)∶5xCr~(3+)(YGG∶xCr)2种多晶粉体(x=0.01,0.03,0.05,0.07)。并采用X射线衍射(XRD)、红外光谱(IR)、扫描电镜(SEM)、荧光光谱(PL)对样品的结构、组成、形貌和荧光性能进行测试分析。XRD和IR分析结果显示在900℃煅烧后Ga_2O_3∶xCr和YGG∶xCr两种样品均成相。SEM照片显示Ga_2O_3∶xCr样品形貌为柱形多面体,YGG∶xCr为短棒状。PL结果显示Cr~(3+)在Ga_2O_3和YGG两种基质中的最强荧光发射峰分别位于742和740 nm,均属于Cr~(3+)的~2E-~4A_2跃迁,对比发现Cr~(3+)在YGG基质中的荧光发射强度更强,在远红光区的荧光性能更好,能满足温室照明中植物光合作用的需求。     

Thermal characterisation of alumina supported chromium and platinum–chromium catalysts

This study presented results on reduction of alumina supported chromium and platinum–chromium catalysts using temperature programmed reduction method (TPR). It has been shown that catalysts after earlier oxidation step but without calcinations one undergo reduction in lower temperature in comparison to calcined only catalysts. Moreover, addition platinum to Cr/Al₂O₃ catalysts also caused decrease of reduction temperature. It has been observed that over the examined catalysts oxidation CO to CO₂ and reduction CO to CH₄ occurs. However, on Pt–Cr catalysts both reactions proceed at lower temperature compare to Cr catalysts.     

Chromium(III)-Ettringite Formation and its Thermal Stability

Attempts have been made to replace aluminium(III) by chromium(III) in the ettringite structure because of practical importance of a waste treatment technology. The optimum conditions of Ca₆[Cr(OH)₆]₂(SO₄)₃⋅26H₂O formation and its thermal stability are reported. This revised version was published online in July 2006 with corrections to the Cover Date.     

Assembling Ultrafine SnO2 Nanoparticles on MIL-101(Cr) Octahedrons for Efficient Fuel Photocatalytic Denitrification

Effectively reducing the concentration of nitrogen-containing compounds (NCCs) remains a significant but challenging task in environmental restoration. In this work, a novel step-scheme (S-scheme) SnO₂@MCr heterojunction was successfully fabricated via a facile hydrothermal method. At this heterojunction, MIL-101(Cr) octahedrons are decorated with highly dispersed SnO₂ quantum dots (QDs, approximate size 3 nm). The QDs are evenly wrapped around the MIL-101(Cr), forming an intriguing zero-dimensional/three-dimensional (0D/3D) S-scheme heterostructure. Under simulated sunlight irradiation (280 nm < λ < 980 nm), SnO₂@MCr demonstrated superior photoactivity toward the denitrification of pyridine, a typical NCC. The adsorption capacity and adsorption site of SnO2@MCr were also investigated. Tests using 20%SnO₂@MCr exhibited much higher activity than that of pure SnO₂ and MIL-101(Cr); the reduction ratio of Cr(VI) is rapidly increased to 95% after sunlight irradiation for 4 h. The improvement in the photocatalytic activity is attributed to (i) the high dispersion of SnO₂ QDs, (ii) the binding of the rich adsorption sites with pyridine molecules, and (iii) the formation of the S-scheme heterojunction between SnO₂ and MIL-101(Cr). Finally, the photocatalytic mechanism of pyridine was elucidated, and the possible intermediate products and degradation pathways were discussed.     

Chromium(III) Hydroxide Solubility in the Aqueous K+-H+-OH?-CO2-HCO 3? -CO 32? -H2O System: A?Thermodynamic Model

Chromium(III)-carbonate reactions are expected to be important in managing high-level radioactive wastes. Extensive studies on the solubility of amorphous Cr(III) hydroxide solid in a wide range of pH (3–13) at two different fixed partial pressures of CO₂(g) (0.003 or 0.03 atm.), and as functions of K₂CO₃ concentrations (0.01 to 5.8 mol⋅kg⁻¹) in the presence of 0.01 mol⋅dm⁻³ KOH and KHCO₃ concentrations (0.001 to 0.826 mol⋅kg⁻¹) at room temperature (22±2 °C) were carried out to obtain reliable thermodynamic data for important Cr(III)-carbonate reactions. A combination of techniques (XRD, XANES, EXAFS, UV-Vis-NIR spectroscopy, thermodynamic analyses of solubility data, and quantum mechanical calculations) was used to characterize the solid and aqueous species. The Pitzer ion-interaction approach was used to interpret the solubility data. Only two aqueous species [Cr(OH)(CO₃)₂²⁻ and Cr(OH)₄CO₃³⁻] are required to explain Cr(III)-carbonate reactions in a wide range of pH, CO₂(g) partial pressures, and bicarbonate and carbonate concentrations. Calculations based on density functional theory support the existence of these species. The log ₁₀ K° values of reactions involving these species [{Cr(OH)₃(am) + 2CO₂(g)⇌Cr(OH)(CO₃)₂²⁻+2H⁺} and {Cr(OH)₃(am) + OH⁻+CO₃²⁻ ⇌Cr(OH)₄CO₃³⁻}] were found to be −(19.07±0.41) and −(4.19±0.19), respectively. No other data on any Cr(III)-carbonato complexes are available for comparisons.     

Effect of Cr and Mn ions on the structure and magnetic properties of GaFeO3: Role of the substitution site

Effect of substitution of Cr and Mn in the Fe and Ga sites of GaFeO₃ on the structural parameters and magnetic properties has been investigated by preparing GaFe_1−xCr_x(Mn_x)O₃ and Ga_1−xCr_x(Mn_x)FeO₃ starting with appropriate oxide precursors. It is shown that, starting with Cr or Mn substituted Ga₂O₃, one obtains Ga_1−xCr_x(Mn_x)FeO₃, while reaction of Cr or Mn substituted α-Fe₂O₃ with Ga₂O₃ yields GaFe_1−xCr_x(Mn_x)O₃. The structural parameters and magnetic properties vary significantly with the substitution site of Cr showing a large decrease in the unit cell parameters as well as the T_C and other magnetic properties when the substitution is at the octahedral Fe (1, 2) site. Substitution of Cr at the octahedral Ga2 site results in marginal changes. Substitution of Mn in the Ga and Fe sites also show differences although the changes themselves are much smaller. First-principles calculations confirm such site-specificity and show how Cr substitution affects the properties differently when substituted at the Ga2 and Fe1 sites.     

Syntheses and characterization of two oxoborates, (Pb3O)2(BO3)2MO4 (M=Cr, Mo)

Two oxoborates, (Pb₃O)₂(BO₃)₂MO₄ (M=Cr, Mo), have been prepared by solid-state reactions below 700 °C. Single-crystal XRD analyses showed that the Cr compound crystallizes in the orthorhombic group Pnma with a=6.4160(13) Å, b=11.635(2) Å, c=18.164(4) Å, Z=4 and the Mo analog in the group Cmcm with a=18.446(4) Å, b=6.3557(13) Å, c=11.657(2) Å, Z=4. Both compounds are characterized by one-dimensional chains formed by corner-sharing OPb₄ tetrahedra. BO₃ and CrO₄ (MoO₄) groups are located around the chains to hold them together via Pb–O bonds. The IR spectra further confirmed the presence of BO₃ groups in both structures and UV–vis diffuse reflectance spectra showed band gaps of about 1.8 and 2.9 eV for the Cr and Mo compounds, respectively. Band structure calculations indicated that (Pb₃O)₂(BO₃)₂MoO₄ is a direct semiconductor with the calculated energy gap of about 2.4 eV.     

含O2高温高压CO2环境中3Cr钢腐蚀产物膜特征

采用高温高压反应釜分别开展3Cr钢在CO2和O2共存、单独CO2和单独O2三种气体条件下的腐蚀实验,利用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、能量色散X射线能谱(EDS)和电化学方法研究了3Cr钢在高温高压含有O2的CO2环境中的腐蚀产物膜特征.结果表明,在含有O2的CO2的条件下,3Cr钢表面腐蚀产物膜疏松多孔,主要成分为FeCO3、Fe3O4和Fe2O3,腐蚀产物中未见明显Cr元素富集,3Cr钢表现出点蚀的腐蚀形态.3Cr钢在高温高压含O2的CO2腐蚀条件下内外膜层电阻(Rf1、Rf2)和电荷传递电阻Rt均比仅含有CO2腐蚀环境的低,双电层电容(Cdl)和内外膜层电容(Cf1、Cf2)均比仅含有CO2腐蚀环境的高.含有O2的CO2条件下,其保护性显著低于单一CO2条件下形成的腐蚀产物膜.提出了在含O2的CO2气体条件下,3Cr钢表面存在由多种物质组成的腐蚀产物,这导致腐蚀产物疏松多孔,不会形成单一CO2条件下存在的显著提高腐蚀产物膜保护性的Cr(OH)3层,从而促进了3Cr钢的析氢腐蚀和酸性介质中的吸氧腐蚀的机理.     

The complex cyanides of chromium(II) and chromium(0)

Summary Chromium(II) cyanide dihydrate has been isolated from the reaction between aqueous chromium(II) and KCN; it can be dehydrated at 100°in vacuo. From the red solutions containing an excess of cyanide, crystalline hexacyanochromates(II) M₄[Cr(CN)₆] (M=Na or K) have been isolated: these are dihydrates at room temperature, but become anhydrous when dried at 100°in vacuo. In liquid ammonia, the hexacyanochromates(II) are reduced to the chromium(O) compounds M₆Cr(CN)₆ by the respective alkali metals. All of these compounds are extremely air-sensitive and are low spin; i.r. and reflectance spectra are reported as well as x-ray powder data for Na₄[Cr(CN)₆], K₄[Cr(CN)₆] and K₆Cr(CN)₆.     

NMR relaxation study of the phase transitions and relaxation mechanisms of the alums MCr(SO4)2·12H2O (M=Rb and Cs) single crystals

The physical properties and phase transition mechanisms of MCr(SO₄)₂·12H₂O (M=Rb and Cs) single crystals have been investigated. The phase transition temperatures, NMR spectra, and the spin-lattice relaxation times T₁ of the ⁸⁷Rb and ¹³³Cs nuclei in the two crystals were determined using DSC and FT NMR spectroscopy. The resonance lines and relaxation times of the ⁸⁷Rb and ¹³³Cs nuclei undergo significant changes at the phase transition temperatures. The sudden changes in the splitting of the Rb and Cs resonance lines are attributed to changes in the local symmetry of their sites, and the changes in the temperature dependences of T₁ are related to variations in the symmetry of the octahedra of water molecules surrounding Rb⁺ and Cs⁺. We also compared these ⁸⁷Rb and ¹³³Cs NMR results with those obtained for the trivalent cations Cr and Al in MCr(SO₄)₂·12H₂O and MAl(SO₄)₂·12H₂O crystals.