Determination of actinide nuclides in water samples from the primary circuit of a research reactor

Primary coolant samples from a research have been analyzed for^239,240Pu,²³⁸Pu,²³⁸U,²³⁷Np and²³⁹Np. The determination of²³⁷Np and²³⁸U was carried out with the help of isotope dilution neutron activation analysis with²³⁹Np or²³⁸Np as tracer. For determination of^239,240Pu and²³⁸Pu alpha spectroscopic isotope dilution analysis with²³⁸Pu as tracer was used.²³⁹Np was determined with the help of isotope dilution analysis using²³⁸Np as tracer. Nuclides were isolated by chemical separation on anionite resin. Before measurement, Pu isotopes were electrolytically deposited on stainless steel plates. Activity ratios referred to²³⁸U were reported. They are helpful for identification of the sources of actinide activity in reactor effluents.     

Distribution and behaviour of99Tc,237Np,239,240Pu,and241Am in the coastal and estuarine sediments of the Irish Sea

Intertidal coastal and estuarine sediments from 24 sites in the Irish Sea have been analyzed for⁹⁹Tc,²³⁷Np,²³⁸Pu,^239,240Pu and²⁴¹Am. The²³⁷Np activity and²³⁹Pu/²⁴⁰Pu ratio were measured simultaneously by ICP-MS, and⁹⁹Tc was determined by HR-ICP-MS which is ten times more sensitive than Q-ICP-MS.The activities of⁹⁹Tc,²³⁷Np,^239,240Pu and²⁴¹Am were distributed over a wide range of 1.5–70.5, 0.01–13.3, 2.3–1589, 2.6–1894 Bq/kg, respectively. Activities of these radionuclides decreased exponentially with distance from the Sellafield source. The²⁴¹Am/^239,240Pu and²³⁷Np/^239,240Pu ratios were almost constant with distance from the Sellafield. This result suggests that the distribution and behavior of Np and Pu are controlled by complicated factors such as the influence of transport, the variation with time of Np/Pu ratio in the Sellafield discharges and sedimentary mixing processes in the Irish Sea.     

3He induced nuclear reactions on237Np targets

The cross sections for the³He induced nuclear reactions on²³⁷Np leading to the formation of^236sNp,²³⁸Np,²³⁶Pu,²³⁷Pu,²³⁸Pu,²³⁷Am and²³⁹Am were studied by the irradiation of thin and thick targets of²³⁷Np. The cross sections were determined in the energy range of 20–26 MeV using the stacked-foil technique with thin targets. The cross sections were used for the calculation of the thick-target yields for the production of²³⁶Pu,²³⁷Pu and²³⁸Pu from²³⁷Np irradiated with³He²⁺ ions in the energy range of 20–26 MeV.     

Rapid determination of 237Np and Pu isotopes in water by inductively-coupled plasma mass spectrometry and alpha spectrometry

A new method that allows rapid preconcentration and separation of plutonium and neptunium in water samples was developed for the measurement of ²³⁷Np and Pu isotopes by inductively-coupled plasma mass spectrometry (ICP-MS) and alpha spectrometry. ²³⁸U can interfere with ²³⁹Pu measurement by ICP-MS as ²³⁸UH⁺ mass overlap and ²³⁷Np via peak tailing. The method provide enhanced removal of uranium by separating Pu and Np initially on TEVA Resin, then moving Pu to DGA resin for additional removal of uranium. The decontamination factor for uranium from Pu is almost 100,000 and the decontamination factor for U from Np is greater than 10,000. This method uses stacked extraction chromatography cartridges and vacuum box technology to facilitate rapid separations. Preconcentration is performed using a streamlined calcium phosphate precipitation method. Purified solutions are split between ICP-MS and alpha spectrometry so that long and short-lived Pu isotopes can be measured successfully. The method allows for simultaneous extraction of 20 samples (including QC samples) in 4?C6 h, and can also be used for emergency response. ²³⁹Pu, ²⁴²Pu and ²³⁷Np were measured by ICP-MS, while ²³⁶Pu, ²³⁸Pu, and ²³⁹Pu were measured by alpha spectrometry.     

Speciation of239U and238Np produced by radiative neutron capture

Various simple and complex compounds of²³⁸U and²³⁷Np have been irradiated in a neutron flux. The chemical state of²³⁹U and²³⁸Np formed in (n, ) reactions has been determined as a function of the initial oxidation state of the actinide elements and of the nature of ligands. A scheme for the chemical reactions following neutron capture is proposed.     

Chemical leaching behavior of237Np from intertidal coastal sediment in the Irish Sea

Chemical leaching experiments of²³⁷Np in the sediments from the Esk Estuary and the Ribble Estuary in the Irish Sea, U. K., have been carried out, in comparison with those of^{239, 240}Pu and²⁴¹Am, to understand the geochemical associations of these long-lived radionuclides with sediment. Experimental results show that partitioning behavior of²³⁷Np is obviously different from those of^{239, 240}Pu and²⁴¹Am.     

Behavior of plutonium isotopes in the marine environment of Enewetak atoll

There continue to be reports in the literature that suggest a difference in the behavior of^239+240Pu and²³⁸Pu in some aquatic environments. Plutonium isotopes have been measured in marine samples collected over 3 decades from Enewetak atoll, one of the sites in the Marshall Islands used by the United States between 1946 and 1958 to test nuclear devices. The plutonium isotopes originated from a variety of complex sources and could possibly coexist in this environment as different physical-chemical species. However results indicate little difference in the mobility and biological availability of^239+240Pu and²³⁸Pu.     

Determination of 237Np and Pu isotopes in large soil samples by inductively coupled plasma mass spectrometry

A new method for the determination of (237)Np and Pu isotopes in large soil samples has been developed that provides enhanced uranium removal to facilitate assay by inductively coupled plasma mass spectrometry (ICP-MS). This method allows rapid preconcentration and separation of plutonium and neptunium in large soil samples for the measurement of (237)Np and Pu isotopes by ICP-MS. (238)U can interfere with (239)Pu measurement by ICP-MS as (238)UH(+) mass overlap and (237)Np via (238)U peak tailing. The method provides enhanced removal of uranium by separating Pu and Np initially on TEVA Resin, then transferring Pu to DGA resin for additional purification. The decontamination factor for removal of uranium from plutonium for this method is greater than 1×10(6). Alpha spectrometry can also be applied so that the shorter-lived (238)Pu isotope can be measured successfully. (239) Pu, (242)Pu and (237)Np were measured by ICP-MS, while (236)Pu and (238)Pu were measured by alpha spectrometry.     

Anomalously high237Np in intertidal sediments from the Ribble Estuary in the Irish Sea

Depth profiles and inventories of²³⁷Np in sediment cores from the Ribble Estuary in the Irish Sea have been studied along with those of Pu isotopes,²⁴¹Am and¹³⁷Cs, to allow a more detailed look of anomalously high²³⁷Np content observed in this estuary previously. The comprehensive data obtained showed that the depth profiles of both²³⁷Np contents and²³⁷Np/^239,240Pu activity ratios were clearly different from those of^239,240Pu,²⁴¹Am, and¹³⁷Cs and their activity ratios. As much as 80–90% of²³⁷Np inventories (0.32–1.06 kBq/m²), found in three cores, were estimated to be derived from a source other than Sellafield, on the basis of comparison of the²³⁷Np/^239,240Pu inventory ratio (0.65–1.74%) found in the Ribble Estuary cores with those (0.10–0.16%) in the Ravenglass Estuary cores.     

Determination of237Np and241Pu in environmental samples: In soil and sediment

This paper describes the analytical methods for the determination of²³⁷Np, Pu isotopes, and²⁴¹Am, with particular emphasis on²³⁷Np by alpha-ray spectrometry and²⁴¹Pu by liquid scintillation technique. Results are also presented for the sediment cores collected from Mikata Five Lakes in Fukui Prefecture, Japan.     

Distribution of global fallout237Np,Pu isotopes,and241Am in lake and sea sediments

In order to investigate the sedimentary behaviour of neptunium,²³⁷Np together with Pu isotopes and²⁴¹Am have been measured for the sediment cores collected from Lake Mikata (freshwater) and from Lake Kugushi (brakish water) both belonging to the Mikata Five Lakes, and from Nyu Bay (sea water). In all sediment core samples²³⁷Np was detected, and its concentrations were far below those of^239,240Pu and²⁴¹Am measured for the same samples. Inventories of²³⁷Np in Lake Mikata, Lake Kugushi and Nyu Bay were estimated to be 0.53, 0.29 and 0.34 MBq/km², respectively. The activity ratio of²³⁷Np/^239,240Pu calculted from the inventories in each sediment core was 0.29% for Lake Mikata, 0.15% for Lake Kugushi and 0.10% for Nyu Bay. These values except for the value for Lake Mikata are two or three times lower than the value of 0.3–0.4% observed for surface soils of 0–20 cm depth, suggesting that Np is more soluble compared with Pu.     

Application of instrumental radioanalytical techniques to nuclear waste testing and characterization

This paper describes the validation of a multi-technique analytical methodology that uses inductively coupled plasma-mass spectrometry, α-spectrometry, and γ-spectrometry for the routine analysis of samples containing transuranic radionuclides. This methodology is capable of the determination of concentrations of both²³⁸Pu and²⁴¹Pu in the presence of²³⁸U and²⁴¹Am without the need for chemical separations. The relative merits of these three techniques were evaluated as they are applied in a nuclear waste material and spent nuclear fuel testing program by analytical (1) standards and (2) solutions prepared from the dissolution of glasses doped with²³⁷Np,²³⁹Pu, and²⁴¹Am. The uncertainty associated with technique was within ±4% for standards and ±10% for doped nuclear waste glasses. The methodology was then used to analyze three fully radioactive waste glasses.     

Sorption characteristics of237Np,238Pu and241Am in sedimentary materials

Adsorption experiments were performed to measure distribution coefficients of²³⁷Np(V),²³⁸Pu(IV) and²⁴¹Am(III) for sedimentary sequential chemical extraction of the adsorbed radionuclides was carried out with water, CaCl₂, KCl, NH₂OH−HCl, K-oxalate and H₂O₂ solutions, to elucidate their dominant sorption mechanisms. The distribution coefficient of²³⁷Np was two orders of magnitude smaller than that of²³⁸Pu and²⁴¹Am. Most of²³⁷Np adsorbed was extracted with CaCl₂ solution and its sorption was controlled by a reversible ion exchange reaction. The adsorbed²³⁸Pu was mainly extracted with NH₂OH−HCl+K-oxalate solution and its sorption was possibly controlled by irreversible reactions.     

Simplified evaluation of214Bi/238U activity ratios in fossil bones using non-destructive activation analysis

A simple and reliable method has been developed for the evaluation of radioactive disequilibrium state in fossil bones. The fossil bone samples were irradiated with an extremely low neutron fluence, together with a standard pitchblende prevailing the secular equilibrium among the uranium series. The²³⁹Np activity induced from²³⁸U in both samples were adjusted to be gamma-ray spectrometrically nearly equivalent to the naturally occurring radioactivities by controlling the neutron flux and cooling time. Using single gamma-ray spectrometry of the irradiated samples, the determination of²¹⁴Bi/²³⁸U in a fossil bone was carried out by comparing the photopeak ratios of²¹⁴Bi /609 keV/ and²³⁹Np /278 keV/ instead of²³⁸U with the same ratios from the pitchblende standard sample.     

Identification of the contamination source of plutonium in environmental samples with isotopic ratios determined by inductively coupled plasma mass spectrometry and alpha-spectrometry

Concentrations of^239+249Pu in environmental samples were detemined by ICP-MS and spectrometry, showing consistent results, which suggests an applicability of ICP-MS to²³⁹Pu and²⁴⁰Pu measurement. The activity ratios of²³⁸Pu/^239+240Pu and²⁴⁰Pu/²³⁹Pu were significantly different in samples from the general environment and near Sellafield reprocessing plants, indicating the usefulness of these ratios for identification of the Pu contamination source.     

Inherent isotope dilution analysis of237Np in spent nuclear fuels

A combined -spectrometric and mass-spectrometric determination of²³⁷Np in spent nuclear fuels using²³⁹Np as an inherent spike has been developed. In spent fuel²³⁹Np is in radiochemical equilibrium with²⁴³Am. Neptunium in the tetravalent state is separated by TTA solvent extraction from the other actinides and most of the fission products and the -activity ratio of²³⁷Np to²³⁹Np is measured. The²³⁷Np activity is via²³⁹Np directly linked to the²⁴³Am mass in a sample, which is determined by mass-spectrometric isotope dilution analysis.     

Plutonium concentration distribution in bed load sediment samples along the Romanian sector of the Danube river and the Black Sea coast

The concentrations of²³⁸Pu and^{239, 240}Pu were determined in 12 sediment samples collected from the bed of the Romanian Danube river and Black Sea coast during June–September 1994. After the sample material has been properly prepared and²⁴²Pu tracer added, plutonium was separated from americium and curium by anion exchange. After electrodeposition on stainless steel discs the elements were counted with an -spectrometry system with silicon surface-barrier detectors. The^{239, 240}Pu concentrations range between 150 and 800 mBq kg^–1 dry, while the²³⁸Pu concentrations rise up to max 150 mBq kg^–1 dry. Although the chemical yields are rather low (51%) we appreciate the results as valuable since they report for the first time the distribution of the plutonium contamination along the Danube river and the Black Sea coast-Romanian sector.     

Experimental evaluation of239Pu,238Pu and233U spikes for determining plutonium concentration by thermal ionization mass spectrometry and alpha-spectrometry

Experimental evaluation on the use of²³⁹Pu spike in Isotope Dilution-Thermal Ionization Mass Spectrometry (ID-TIMS),²³⁸Pu spike in Isotope Dilution Alpha Spectrometry (IDAS) and²³³U as a Non-Isotopic Diluent in Alpha Spectrometry (N-IDAS), for determing plutonium concentration in samples with burn-up values in the range of 1,000–10,000 MWD/TU is done. Precision is determined by analyzing replicate aliquots from different samples using each of the three spikes. Accuracy is established by comparing the results with those obtained by using well recognized spike²⁴²Pu in ID-TIMS. It is shown that the use of²³⁹Pu spike with the latest generation thermal ionization mass spectrometers gives the best precision (0.2%), whereas the precision values of 0.5 and 1% can be obtained by using²³⁸Pu and²³³U spikes, respectively, on a routine basis. Reasons for the difference in the precision values are discussed, along with the merits and drawbacks on the use of different spike isotopes.     

Determination of237Np in spent fuel by use of inherent239Np as a chemical yield monitor

A method for analyzing the content of²³⁷Np in spent fuel has been developed using inherent²³⁹Np as a chemical yield monitor. After ion-exchange separations for the dissolved fuel solution, the²³⁷Np content in the neptunium fraction was determined from the activity of²³⁷Np or of²³³Pa, which is in radioactive equilibrium with²³⁷Np. The chemical yield in the separations was determined both from the content of²⁴³Am which is in radioactive equilibrium with²³⁹Np before the separations and from the²³⁹Np content in the neptunium fraction after the separations by alpha- and gamma-ray spectrometry.     

Simultaneous determination of uranium and plutonium isotopes in soils by means of single alpha-spectrometry

A simple, rapid and reliable method was developed for the simultaneous determination of uranium and plutonium isotopes by alpha-spectrometry using a single source. A new uranium tracer²³⁰U was applied as well as the²³⁶Pu tracer to determine overall yields of uranium and plutonium isotopes throughout the entire procedure employed. The analytical procedure consists of sample leaching with 8N HNO₃ solution, purification by solvent extraction, simultaneous electrodeposition of U and Pu, and subsequent alpha-spectrometry with a silicon detector. In the solvent extraction using TOA/xylene from 8N HNO₃ solution, the preferential extractability of Pu rather than U permits to purify simultaneously the trace amounts of Pu and the macro amounts of U, as in the case of ordinary soil samples, resulting in favourable peak heights for both isotopes. From a single alpha-spectrum, the determinations of²³⁸U,²³⁴U (and their ratio of²³⁴U/²³⁸U),^239+240Pu, and²³⁸Pu contents were conveniently carried out after correcting the overall yields obtained from²³⁰U and²³⁶Pu activities in the same spectrum. This analytical method was satisfactorily applied to the determination of U and Pu isotope contents in some soils.