Studies on the matched potential method for determining the selectivity coefficients of ion-selective electrodes based on neutral ionophores: experimental and theoretical verification.

A theory is presented that describes the matched potential method (MPM) for the determination of the potentiometric selectivity coefficients (KA,Bpot) of ion-selective electrodes for two ions with any charge. This MPM theory is based on electrical diffuse layers on both the membrane and the aqueous side of the interface, and is therefore independent of the Nicolsky-Eisenman equation. Instead, the Poisson equation is used and a Boltzmann distribution is assumed with respect to all charged species, including primary, interfering and background electrolyte ions located at the diffuse double layers. In this model, the MPM-selectivity coefficients of ions with equal charge (ZA = ZB) are expressed as the ratio of the concentrations of the primary and interfering ions in aqueous solutions at which the same amounts of the primary and interfering ions permselectively extracted into the membrane surface. For ions with unequal charge (ZA not equal to ZB), the selectivity coefficients are expressed as a function not only of the amounts of the primary and interfering ions permeated into the membrane surface, but also of the primary ion concentration in the initial reference solution and the delta EMF value. Using the measured complexation stability constants and single ion distribution coefficients for the relevant systems, the corresponding MPM selectivity coefficients can be calculated from the developed MPM theory. It was found that this MPM theory is capable of accurately and precisely predicting the MPM selectivity coefficients for a series of ion-selective electrodes (ISEs) with representative ionophore systems, which are generally in complete agreement with independently determined MPM selectivity values from the potentiometric measurements. These results also conclude that the assumption for the Boltzmann distribution was in fact valid in the theory. The recent critical papers on MPM have pointed out that because the MPM selectivity coefficients are highly concentration dependent, the determined selectivity should be used not as "coefficient", but as "factor". Contrary to such a criticism, it was shown theoretically and experimentally that the values of the MPM selectivity coefficient for ions with equal charge (ZA = ZB) never vary with the primary and interfering ion concentrations in the sample solutions even when non-Nernstian responses are observed. This paper is the first comprehensive demonstration of an electrostatics-based theory for the MPM and should be of great value theoretically and experimentally for the audience of the fundamental and applied ISE researchers.     

Poly(vinyl chloride) membrane cesium ion-selective electrodes based on lipophilic calix[6]arene tetraester derivatives

New lipophilic tetraesters of calix[6]arene and calix[6]diquinone are investigated as cesium ion-selective ionophores in poly(vinyl chloride) membrane electrodes. For an ion-selective electrode based on calix[6]arene tetraester I, the linear response is 1x10(-6)-1x10(-1) M of Cs(+) concentrations. The selectivity coefficients for cesium ion over alkali, alkaline earth and ammonium ions are determined. The detection limit (log a (Cs (+))=-6.31) and the selectivity coefficient (log k (Cs (+),Rb (+))(pot )=-1.88) are obtained for polymeric membrane electrode containing calix[6]arene tetraester I.     

Determination of true selectivity coefficients of neutral carrier calcium selective electrode

Literature data concerning selectivity coefficients of neutral carrier calcium selective electrode show large discrepancies up to several orders of magnitude for sensors containing the same active component. It can be shown theoretically that determination of selectivity coefficients in non-complexing media gives too high values because of additional sources of the main ion in the membrane vicinity. Determination of selectivity coefficients in solutions containing a complexing agent gives the possibility to evaluate true selectivity coefficients not influenced by additional factors. Measurements performed in complexing as well as in non-complexing media and calculation of the detection limit indicate a good agreement between expectations and experimental results. This has been confirmed using the calcium selective electrode with the neutral carrier ETH 1001 witho-nitrophenyl octyl ether or dioctylsebacate as mediators. As interferents sodium, potassium and magnesium ions were tested.     

Ion-selective electrode for measuring low Ca2+ concentrations in the presence of high K+, Na+ and Mg2+ background

In this work, ion-selective electrodes for calcium ion were investigated. Two ionophores were used in the membranes: ETH 1001 and ETH 129. An internal filling solution buffered for primary ion was used that allowed the lower detection limit to be decreased down to 10^−8.8 M. Theoretical and experimental electrode characteristics pertaining to both primary and interfering ions are discussed. Better behavior was obtained with the electrode prepared with ETH 129 in the membrane. This electrode would be the most likely candidate for obtaining a low Ca²⁺ detection limit in measurements performed with high K⁺, Na⁺, Mg²⁺ background, which is found inside the cells of living organisms, for example. The potentiometric response of the electrode in solutions containing main and interfering ions is in good agreement with simulated curves obtained using the Nernst–Planck–Poisson (NPP) model.     

Flow-through calcium-selective electrode: application in flow-injection analysis and ion chromatography

The use of solid contact flow-through calcium-selective electrodes as potentiometric detectors in flow-injection analysis and non-suppressed ion chromatography is discussed. Owing to the high selectivity of the membrane electrode based on tetratolyl-m-xylylenediphosphine dioxide, it can be used to monitor trace amounts of calcium ions in the presence of a 100-fold excess of alkali metal, ammonium and magnesium ions. The detection limit is about 1 × 10^?6 M. The composition and thickncss of the calcium selective membrane influence both the detection limit and selectivity of the electrode. The sensitivity of this potentiometric detector in ion chromatography relative to alkaline earth and heavy metals is significantly higher than that of a commercial conductivity detector.     

Calixazacrown ethers for copper(II) ion-selective electrode

Five novel 1,3-alternate calix[4]azacrown ethers having 2-picolyl, 3-picolyl, and benzyl unit on the nitrogen atom were synthesized and used as ionophores for transition metal-selective polymeric membrane electrodes. The electrode based on 2-picolyl armed 1,3-alternate calix [4] azacrown ether exhibited Nernstian response toward copper (II) ion over a concentration range (10(-4.5) M-10(-2.5) M). The detection limit was determined as 10(-5) M in pH 7 and the selectivity coefficients for possible interfering cations were evaluated. Anions in the sample solution strongly affected the electrode response.     

Ion-selective liquid electrodes: Problems of description and experimental determination of selectivity

Current state of selectivity theory for liquid-membrane ion-selective electrodes was considered. Analytical expressions for the selectivity coefficients of electrodes based on liquid ion exchangers, neutral carriers, and charged carriers were obtained using phase boundary potential model. The reasons responsible for the dependence of experimentally determined selectivity coefficients on the determination conditions are discussed. The main ways for the electrode design optimization providing dramatic improvement of the selectivity are considered.     

Liquid-membrane dicyanoargentate-sensitive electrodes based on quaternary ammonium salts

Several quaternary ammonium salts have been synthesized and comparisons made of their efficiency as exchange substrates in dicyanoargentate-sensitive electrodes. The electrode prepared from hexadecyltrioctylammonium dicyanoargentate shows the best performance characteristics and has been studied in more detail. Its Nernstian response range is 10(-1)-10(-4)M, the optimum pH range is 10.6-12.6, and the detection limit is 3 x 10(-5)M. It is suggested that the detection limit of the electrode is controlled by interference from cyanide ions, and the difference between detection limits obtained with the various electrodes is discussed in the light of this. Selectivity coefficients for various interfering ions have been determined and related to the extractability of the ions. The electrode has been applied to determination of silver in cyanide-containing plating solutions.     

A Method of Determining Selectivity Coefficients Based on the Practical Slope of Ion Selective Electrodes

It is a problem to be solved that the experimental selectivity coefficients of ion selective electrodes( ISEs) depend on the activity. This paper studied the new method of determining selectivity coefficients. A mixed ion response equation, which was similar to Nicolsky-Eisenman (N-E) equation recommended by IUPAC, was proposed. The equation includes the practical response slope of ISEs to the primary ion and the interfering ion. The selectivity coefficient was defined by the equation instead of the N-E equation. The experimental part of the method is similar to that based on the N-E equation. The values of selectivity coefficients obtained with this method do not depend on the activity whether the electrodes exhibit the Nernst response or non-Nernst response. The feasibility of the new method is illustrated experimentally.     

Modern potentiometry

For most chemists, potentiometry with ion-selective electrodes (ISEs) primarily means pH measurements with a glass electrode. Those interested in clinical analysis might know that ISEs, routinely used for the determination of blood electrolytes, have a market size comparable to that of glass electrodes. It is even less well known that potentiometry went through a silent revolution during the past decade. The lower detection limit and the discrimination of interfering ions (the selectivity coefficients) have been improved in many cases by factors up to 10(6) and 10(10), respectively, thus allowing their application in fields such as environmental trace analysis and potentiometric biosensing. The determination of complex formation constants for lipophilic hosts and ionic guests is also covered in this Minireview.     

Guanidinium-selective PVC membrane electrodes based on crown ethers

Guanidinium-selective membrane electrodes were constructed with dibenzo-24-crown-8, dibenzo-27-crown-9, tribenzo-27-crown-9 or dibenzo-30-crown-10. The detection limits and selectivity coefficients towards different interfering ions, such as Li⁺, Na⁺, K⁺, NH⁺₄, Mg²⁺ and Ca²⁺ were determined. The electrode with dibenzo-27-crown-9 shows linear response over the range 10^?1–10^?4 M, with selectivity coefficients about 10^?2 for most alkali and alkaline earth metal ions.     

Measuring quaternary ammonium cleaning agents with ion selective electrodes

Data for coated-wire, ion selective electrodes (ISEs) are presented for cationic surfactant ions found in common cleaners including benzyldimethyltetradecylammonium, benzyldimethyldodecylammonium, and benzyldimethylhexadecylammonium. The ion exchangers dinonylnaphthalene sulfonic acid, tetraphenyborate, and tetrakis(4-chlorophenyl)borate are examined, showing dinonylnaphthalene sulfonic acid to be the favored species. The ISEs exhibit approximately Nernstian behavior down to the 10⁻⁶ M limit of detection with lifetimes in excess of 50 days when used continuously, and a shelf life of over 100 days. Reaching the upper detection limit at the critical micelle concentration requires use of polymeric-membrane reference electrodes including a new membrane cocktail, which allow response measurements of an order of magnitude higher than the traditional fritted-glass reference electrode. The surfactant ISEs show excellent selectivity over the common metal ions Na⁺, K⁺, Mg²⁺, Ca²⁺, and Cu²⁺ with selectivity coefficients less than 10^−5.3. The ISEs are also selective over the lower molecular weight quaternary ammonium ions tetradecyltrimethylammonium, dodecyltrimethylammonium, benzyldimethyl(2-hydroxyethyl)ammonium, and tetrabutylammonium with selectivity coefficients ranging from 10^−1.7 to 10^−5.5. Use of a single electrode to determine accurately the total cationic surfactant concentration in common cleaning solutions is accomplished with information about concentration dependent interferences and a modified Nikolsky–Eisenman model. Finally, quaternary ammonium surfactants have a deleterious effect on the measurements of pH and common ions like K⁺, Mg²⁺ and Ca²⁺ with polymeric ISEs. This makes it critical to include surfactant electrodes in a detector array when cleaning agents are present.     

Triethylene glycol ether end-grafted carbosilane dendrimer: a potential ionophore for potassium ion recognition.

The performance of a newly synthesized carbosilane dendrimer bearing four triethylene glycol ether (TEG) units, Si(CH2CH2CH2Si(Me)2CH2CH2CH2(OCH2CH2)3Me)4 (1), as ionophores in ion-selective electrodes has been investigated. Optimization of the plasticized polyvinyl chloride membrane composition has produced electrodes that exhibit a Nernstian response for potassium ions. The best general characteristics exhibited by the electrodes were found when the membrane composition ratio of DPE:1:NaTPB:PVC 60:3:2:35 (wt%) was used. The response of the electrode was linear with a Nernstian slope of 58.3 mV/decade over the K+ ion concentration range of 1.9x10(-7) to 1.0x10(-1) M with a detection limit of 3.1x10(-7) M. The response time to achieve a 95% steady potential for the K+ concentration ranging from 1.0x10(-1) to 1.0x10(-8) M was less than 10 s, and it was found that the electrode is suitable for use within a pH range of 5.5-8.5. The selectivity coefficients (log KPotK+,Mn+)), which were determined by the fixed interference method, showed good selectivity for K+ against most of the interfering cations. The influence of this selective ion-binding behavior using electrospray ionization time-of-flight (ESI-TOF) mass spectrometric studies is discussed.     

Determination of SCN- in urine and saliva of smokers and non-smokers by SCN(-)-selective polymeric membrane containing a nickel(II)-azamacrocycle complex coated on a graphite electrode.

The construction, performance characteristics, and application of a novel polymeric membrane coated on a graphite electrode with unique selectivity towards SCN- are reported. The electrode was prepared by incorporating Ni(II)-2,2,4,9,9,11-hexamethyltetraazacyclotetradecanediene perchlorate into a plasticized poly(vinyl chloride) membrane. The influences of membrane composition, pH and foreign ions were investigated. The electrode displays a near Nernstian slope (-57.8 mV decade-1) over a wide concentration range of 1 x 10(-7)-1 x 10(-1) M of SCN- ion. The electrode has a detection limit of 4.8 x 10(-8) M (2.8 ng/cm3) SCN- and shows response times of about 15 s and 120 s for low to high and high to low concentration sequences, respectively. The proposed sensor shows high selectivity towards SCN- over several common organic and inorganic anions. The electrode revealed a great enhancement in selectivity coefficients and detection limit for SCN-, in comparison with the previously reported electrodes. It was successfully applied to the direct determination of SCN- in milk and biological samples, and as an indicator electrode in titration of Ag+ ions with thiocyanate.     

冠醚载体离子电极的选择特性研究

阴离子选择电极选择性系数随干扰离子r_j/z_j的变化规律已有报道,但冠醚为中性载体的金属离子电极的选择性系数规律未见报道。本文采用不同桥间结构的11种苯并双冠醚作为中性载体,从钾电极出发探讨了不同冠醚电极选择性系数与干扰离子r_j/z_j间的关系;并以4种烃型双冠醚为中性载体,分别考察了它们对Li~+、Rb~+、Cs~+、Ag~+、Ba~(2+)离子的响应规律。 1 实验部分     

A method for the determination of potentiometric selectivity coefficients of ion selective electrodes in the presence of several interfering ions

In this work a new method is reported for the determination of potentiometric selectivity coefficients of ion-selective electrode in which, similar to real samples, several interfering ions are simultaneously present in test solutions and where the electrode shows its practical behavior. In order to illustrate this method, the potentiometric selectivity coefficients of a commercial liquid membrane ammonium selective electrode is determined for biologically important interfering ions: Li(+), Na(+) and K(+).     

基于硫氮杂冠醚离子载体的高选择性聚合物膜汞离子选择性电极

以硫氮杂冠醚化合物为离子载体,制备了一种高选择性聚合物膜汞离子选择性电极.通过对电极膜的组成及活化条件进行优化,电极在3.0×10-8～1.0×10-4 mol/L的范围内对汞离子呈能斯特响应,响应斜率为31.2 mV/dec,检出限为2.0×10-8 mol/L.该电极对大多数常见的金属离子具有良好的选择性,并可作为指示电极用于电位滴定.     

Zeolite-Modified Sol-Gel Electrode as an Electrochemical Sensor for Potentiometric Determination of Cesium Ions in Water Samples

Abstract

In this research, new electrodes were prepared by incorporating zeolite KY into sol-gel matrix. Calibration plot with Nernstian slope (58.6 ± 0.5 mV/decade) for cesium ion was observed over a linear range of about four decades of concentration (1.0 × 10^?5 to 1.0 × 10^?1 M, at 25°C). The sol-gel electrode shows detection limit of 7.3 × 10^?6 M. The influences of membrane composition, the pH of the test solution, and the interfering ions on the electrode performance were investigated. The effect of temperature on the electrode response showed that the temperature higher than 60°C deteriorates the electrode performance. The proposed electrode has high mechanical and thermal stability with a low isothermal temperature coefficient, and it is 0.00018 V/°C. It has a short response time (10 s) and can be used for more than 6 months without any considerable divergence in the potentials. The selectivity coefficients for Cs⁺ ion with respect to alkali, alkaline earth, ammonium, and some heavy-metal ions were investigated. The results of application show that the electrode can be used successfully in determination of Cs⁺ ions in various water samples.