共查询到20条相似文献,搜索用时 15 毫秒
1.
B. S. Yilbas 《Surface and interface analysis : SIA》2014,46(1):30-35
Laser surface treatment of Rene 41 high‐performance alloy is carried out with the presence of hard particles at the surface. B4C and SiC particles are uniformly distributed within 40 µm carbon film at the workpiece surface prior to laser treatment process. The effect of hard particles on residual stress and microhardness variations is investigated at the treated surface. Morphological and metallurgical changes in the treated layer are examined by using electron microscopy, energy dispersive spectroscopy, and X‐ray diffraction. Residual stress formed at the surface is determined from the X‐ray data. It is found that the treated surface is free from asperities such as large size voids and cracks. A dense layer is formed in the surface region, which causes volume shrinkage while contributing to microhardness and residual stress enhancement at the surface. B4C hard particles result in the highest residual stress and microhardness at the surface, which is attributed to its high thermal expansion coefficient. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
2.
B. J. Abdul Aleem M. S. J. Hashmi B. S. Yilbas 《Surface and interface analysis : SIA》2012,44(2):150-155
Laser treatment of a high‐speed steel surface is carried out and metallurgical and morphological changes in the laser‐treated layer are examined using SEM, EDS and XRD. A carbon film of 50 µm thickness and containing 5% TiC particles is formed at the workpiece surface prior to the laser treatment process. The carbon film formed at the surface enhances the absorption of laser irradiation and retains TiC particles at the workpiece surface. The residual stress formed at the laser‐treated surface is determined using the XRD technique while the indentation tests are carried out to measure microhardness and fracture toughness of the resulting surface. It is found that ε‐Fe3N, and ε‐Fe3 (N,C) compounds are formed at the laser‐treated surface, which are attributed to the presence of carbon film and high‐pressure nitrogen‐assisting gas. The fracture toughness of the laser‐treated surface reduces because of the increased hardness and dense layer formed at the surface vicinity. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
3.
High‐speed tool steel (AISI M2) surface is pre‐prepared to form a thin carbon film containing 5% B4C particles prior to laser treatment process. Morphological and metallurgical changes are examined in the treated layer using electron microscope, energy dispersive spectroscopy, and X‐ray diffraction. The microhardness and the residual stress formed at the treated surfaces are measured for samples with and without B4C particles. It is found that the micro‐stresses formed in the neighborhood of B4C particles at the treated surface contributed to the microhardness enhancement at the surface. This is associated with the mismatch of thermal expansion coefficients between B4C particles and the base alloy. The nitride phases are formed at the treated surface, which also contribute to the microhardness increase at the surface. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
4.
B. S. Yilbas I. H. Toor C. Karatas F. Patel M.M.A. Baig 《Surface and interface analysis : SIA》2012,44(10):1364-1369
Laser controlled melting of metal surface provides a local treatment with improved surface properties such as corrosion resistance. In the present study, laser surface treatment of iron base superalloy (A286) is carried out. The corrosion resistance of the laser‐treated surface is examined through potentiodynamic tests using 0.5 N NaCl solution. The microstructural and morphological changes in the laser‐treated layer are investigated incorporating scanning electron microscopy (SEM), X‐ray diffraction (XRD) and energy dispersive spectroscopy. The residual stress formed at the laser‐treated surface is measured using the XRD technique. It is found that laser treatment enhances corrosion resistance of A286 superalloy surface, which is attributed to the formation of fine grains and dense layer at the treated surface. Although locally scattered few corrosion induced microcracks are observed at the treated surface, they are not extended to form large cracks or crack network at the surface. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
5.
Alexander S. Quick Joachim Fischer Benjamin Richter Thomas Pauloehrl Vanessa Trouillet Martin Wegener Christopher Barner‐Kowollik 《Macromolecular rapid communications》2013,34(4):335-340
Three‐dimensional microstructures are fabricated employing the direct laser writing process and radical thiol‐ene polymerization. The resin system consists of a two‐photon photoinitiator and multifunctional thiols and olefins. Woodpile photonic crystals with 22 layers and a rod distance of 2 μm are fabricated. The structures are characterized via scanning electron microscopy and focused ion beam milling. The thiol‐ene polymerization during fabrication is verified via infrared spectroscopy. The structures are grafted in a subsequent thiol‐Michael addition reaction with different functional maleimides. The success of the grafting reaction is evaluated via laser scanning microscopy and X‐ray photoelectron spectroscopy. The grafting density is calculated to be close to 200 molecules μm−2. 相似文献
6.
Titanium carbide (TiC) thin films were deposited on D9 steel substrates at room temperature (RT), 200 °C and 400 °C. A compound TiC target was sputtered to deposit films in a non‐reactive argon atmosphere. As‐deposited films were characterised for structural, chemical and mechanical properties. Nanoindentation and scratch tests were performed to evaluate the cohesive and adhesive strength of the films, respectively. Tribological properties of the films were investigated using a tribometer. An increase in nano‐hardness from 7.2 to 10.5 GPa was observed as deposition temperature was increased. The films deposited at RT and 200 °C showed poor adhesion leading to the inferior tribological performance. In contrast, films deposited at 400 °C showed better adhesion which improved the wear resistance. Tribological behaviour of TiC thin films was correlated with contact deformation modes of coatings. These modes revealed significant role of adhesive and cohesive strength associated with the coatings. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
7.
Jorge López‐García Marian Lehocký Petr Humpolíček Igor Novák 《Surface and interface analysis : SIA》2014,46(9):625-629
Non‐thermal non‐equilibrium oxidative air 40‐kHz frequency, 13.56‐MHz radiofrequency and 2.46‐GHz microwave discharge plasma treatment were used for modifying low‐density polyethylene foils. The untreated and treated samples were chemically characterised by X‐ray photoelectron spectroscopy. In order to estimate the extent of the plasma sources at distinct treatment times, surface charge and energy were determined by zeta potential (ζ) and surface tension measurements. In addition, the isoelectric points (IEPs) of the studied samples were ascertained, and surface property variations were appraised by ageing time. The overall outcome indicated that ζ‐potential and surface energy progressively changed after each treatment, as well as the influences of ageing on surface features, the IEP shifting to lower pH values and how all of these changes are associated with the new surface chemistry. This contribution seeks to shed light on topics related to polymer science and plasma‐based strategies for surface modification. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
8.
《Surface and interface analysis : SIA》2005,37(13):1151-1157
A theoretical method to determine the so‐called surface excitation parameter (SEP) is presented. This method is based on the modelling of reflection‐electron‐energy‐loss spectroscopy and more particularly on the analysis of energy‐differential inelastic electron scattering cross sections calculated within the model. The SEP is extracted from theoretical cross‐section spectrum by calculating the ratio between the surface loss component of the spectrum and the elastic peak intensity. The calculations have been performed entirely with the dielectric function, using the software QUEELS (Quantitative analysis of Electron Energy Losses at Surfaces) recently developed by Yubero and Tougaard [Surf. Interface Anal. 2004; 36 : 824]. The angular distribution of SEP is calculated for angles between 10° and about 70° for aluminium and silicon. We propose also an extension of the method for materials (e.g. copper) that do not present clear surface and volume plasmons. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
9.
金银合金纳米粒子表面处理及其表面增强拉曼光谱研究 总被引:1,自引:0,他引:1
采用水合肼还原的方法制备了金银比例为1∶1的金银合金纳米粒子, 紫外可见吸收光谱显示合成的溶胶只有一个介于金和银之间的吸收峰, 证明了合金结构的形成. 通过氨基耦联方法将合金纳米粒子组装到硅片表面, 利用氯金酸与合金中银的反应对基底上合金纳米粒子表面进行了改性处理. 以吡啶为探针分子, 研究了表面处理前后基底的SERS效应的差别, 结果表明随着浸泡时间延长, 信号强度先逐渐增强后降低至不变, 这与合金纳米粒子表面结构的变化有关, 氯金酸与表面银的反应经历了两个过程, 即粒子表面形成小的孔洞(去合金过程)和AgCl(s)在粒子表面的沉积, 前者有利于SERS效应的提高, 而后者导致SERS效应快速衰减. 相似文献
10.
《先进技术聚合物》2018,29(10):2601-2611
Biomaterials and their host organism's quintessential place of interaction are the surfaces of materials, as transportation of liquids within microchannels requires hydrophilic surfaces. Modifying the hydrophobic surface of polydimethylsiloxane (PDMS) into a hydrophilic one which can be used in biomaterials remains a big challenge. Herein, PDMS‐hydroxyethylmethacrylate (HEMA) films were prepared by the condensation of PDMS using isophorone diisocyanate as a cross‐linker, followed by the incorporation of HEMA via radical copolymerization. The as‐prepared PDMS‐HEMA films were thereafter hydrophilized via physical treatment with heptamethyltrisiloxane. The surface properties of the obtained PDMS‐HEMA films were characterized in wettability, morphology, topography, swelling, mechanical properties, and protein adsorption. Compared to pristine PDMS‐HEMA as control, the surface wettability, roughness, and protein adsorption of the hydrophilized PDMS‐HEMA films were significantly improved while the films also exhibited excellent optical properties. However, the improvement of the swelling properties remains insignificant, indicating that the interior morphology was still based on the hydrophobic siloxane PDMS. The long‐term hydrophilicity was considered good as no significant hydrophobic recovery was noticeable in a period of 5 months after treatment. 相似文献
11.
《先进技术聚合物》2018,29(4):1322-1333
This work aims to develop novel composites from a poly(L ‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG) terpolymer and mesoporous silica (SBA‐15) nanofillers surface modified by post‐synthetic functionalization. SBA‐15 first reacts with a silane coupling agent, γ‐aminopropyl‐trimethoxysilane to introduce ammonium group. PLLA chains were then grafted on the surface of SBA‐15 through ammonium initiated ring‐opening polymerization of L ‐lactide. Composites were prepared via solution mixing of PLTG terpolymer and surface modified SBA‐15. The structures and properties of pure SBA‐15, γ‐aminopropyl‐trimethoxysilane modified SBA‐15 (H2N‐SBA‐15), PLLA modified SBA‐15 (PLLA‐NH‐SBA‐15), and PLTG/PLLA‐NH‐SBA‐15 composites were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, transmission electron microscopy, N2 adsorption‐desorption, differential scanning calorimetry, contact angle measurement, and mechanical testing. The results demonstrated that PLLA chains were successfully grafted onto the surface of SBA‐15 with grafting amounts up to 16 wt.%. The PLTG/PLLA‐NH‐SBA‐15 composites exhibit good mechanical properties. The tensile strength, Young's modulus, and elongation at break of the composite containing 5 wt.% of PLLA‐NH‐SBA‐15 were 39.9 MPa, 1.3 GPa, and 273.6%, respectively, which were all higher than those of neat PLTG or of the composite containing 5 wt.% of pure SBA‐15. Cytocompatibility tests showed that the composites present very low cytotoxicity. 相似文献
12.
《Surface and interface analysis : SIA》2005,37(3):332-335
We studied the effects of Ga isotope implantation on surface structure using single‐crystal (0001) ZnO with an atomically flat surface. The surface morphology with steps and terraces was greatly changed by Ga implantation and post‐annealing: the step‐and‐terrace structure was suppressed by Ga implantation but a step‐and‐terrace structure appeared on the surface after post‐annealing at 900 °C for 4 min. The diffusion of Ga towards the surface through dislocation pipes at a density of up to 5 × 108 cm?2 was the dominant mechanism, and a significant amount of Ga moved from the implanted layer to the surface. The reaction between Ga and ZnO during post‐annealing appeared to improve sheet resistance and surface morphology. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
13.
Jianwei Qi Liping Wang Fengyuan Yan Qunji Xue 《Surface and interface analysis : SIA》2011,43(4):836-846
TiC/a‐C:H and a‐C:H nanocomposite coatings were prepared on AISI 440C steel substrates using magnetron sputtering process. A comparative study was made on their composition and microstructure by Raman spectroscopy and high‐resolution transmission electron microscopy (HRTEM). The tribological properties of two types of carbon‐based coatings were investigated by pin‐on‐disc tribometer under the sand‐dust conditions concerning the influence of applied load, amount of sand and sand particle sizes. The results show that these carbon‐based coatings exhibited high tribological performance with low friction coefficient and wear rate under the sand‐dust environments. However, the TiC/a‐C:H coatings exhibit relatively higher fluctuant friction coefficient as well as higher wear rate in comparison with the a‐C:H coatings under sand‐dust environments. The formation of nanocrystalline hard TiC phase distributed in amorphous carbon matrix decreased the residual stress but significantly increased the hardness and Young's modulus of TiC/a‐C:H coatings, and consequently caused a relatively higher abrasive and fatigue wear loss under the sand‐dust conditions. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
14.
Deshmukh RD Composto RJ 《Langmuir : the ACS journal of surfaces and colloids》2007,23(26):13169-13173
Direct embedding of metal nanoparticles (NPs) into the surface of a polymer melt is observed by TEM and a new embedding mechanism proposed. Upon annealing above the glass transition temperature of polystyrene (PS), NPs (20 nm gold) are rapidly covered by a thin PS wetting layer, h* approximately 1.3-1.8 nm (i.e., about two or three monomers). Because it creates capillary pressure on a NP, this "universal" wetting layer is proposed to be responsible for NP embedding. The value of h* is independent of the molecular weight of PS and constant during the embedding process. The value of h* is found to be similar to the equilibrium wetting layer thickness of a polymer melt spreading on a metal substrate. Using a model that includes the spreading coefficient, long-range van der Waals interactions, and a chain-stretching penalty, h* is shown to be independent of the molecular weight of the polymer. Using this model and the measured value of h*, the interfacial energy between Au NP and PS is estimated to be 8.7 J/m2. 相似文献
15.
Research into azobenzene and its compounds focuses on the molecules ability to cis‐trans isomerize, this photoisomerization enables surface relief gratings (SRGs) to be formed on the azobenzene functionalized polymer films. SRG allows information to be written and then erased, an essential requirement of most modern electrical products. The interest into SRG photofabrication is thus rapidly increasing and is emerging at the forefront of photonic and nanotechnology research. The surface relief grating mechanism, however, is not fully understood, a photoplasticization process is postulated, which is thought to occur via the azo‐chromophores photoisomerization, so encouraging polymer chain migration to the surface. In comparison, suggestions have shown the SRG process does not involve a change in the film surface profile but in the local refractive index. Currently, no research has yet established the surface relief grating mechanism, this paper sets out to determine the mechanism and investigate those theories already postulated by observing the thin film surfaces prior to and after SRG using X‐ray photoelectron spectroscopy (XPS). By identifying the surface components, greater insight and understanding of the SRG mechanism can be achieved. In this paper, poly(4‐(N‐(2‐methacryloyloxyethyl)‐N‐ethylamino)‐4′‐nitroazobenzene)90‐co‐(methylmethacrylate)10 50 : 50 PMMA blend was exposed to SRGs. Using XPS the surface composition was determined prior to and after SRG. Following SRG, the spectra for O 1s, N 1s and C 1s using XPS expressed a change in the components at the surface. This is most evident in the N 1s spectra, with PMMA not containing nitrogen, the N 1s becomes the determining factor. The nitrogen absence combined with a significant increase in the carbon and oxygen peak intensity concludes the azobenzene lies not on the surface but, in fact, within the bulk after SRG. The initial light irradiation process must be a consideration. However, on X‐ray analysis the sample showed the same spectra as the one prior to SRG. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
16.
ZrO2和Al2O3在金红石型TiO2表面的包覆研究 总被引:3,自引:0,他引:3
以(NaPO3)6为分散剂,用化学沉积法对金红石型TiO2进行了锆、铝氧化物包膜。研究了包覆过程中,TiO2的分散、ZrO2和Al2O3用量、反应pH值以及时间对二氧化钛的亨特白度(Wh)和光泽度(L)的影响,并采用扫描电镜(SEM)、透射电镜(TEM)、X光电子能谱(XPS)和沉降性试验对包覆前后的二氧化钛进行了表征,得到包锆、包铝氧化物的优化工艺条件。研究了二氧化钛表面包锆、铝氧化物的包覆机理和表面结构。经过其表面包膜处理,二氧化钛的颜料性能得到明显改善。 相似文献
17.
Surface‐initiated nitroxide‐mediated polymerization of sodium 4‐styrene sulfonate from latex particles
下载免费PDF全文
![点击此处可从《Journal of polymer science. Part A, Polymer chemistry》网站下载免费的PDF全文](/ch/ext_images/free.gif)
Claude St Thomas Judith Nazareth Cabello‐Romero Omar Garcia‐Valdez Enrique Javier Jiménez‐Regalado Hortensia Maldonado‐Textle Ramiro Guerrero‐Santos 《Journal of polymer science. Part A, Polymer chemistry》2017,55(3):437-444
In this study, we report the use of a double‐headed dialkoxyamine trithiocarbonate ( I ) capable of acting as chain transfer agent via reversible addition‐fragmentation chain transfer polymerization or as initiator via nitroxide‐mediated polymerization. It is worth mentioning that I was revealed as an effective dual chain transfer agent in the synthesis of multiblock copolymers via bulk and emulsion processes. In this article, we report the employing of I in dispersed systems to obtain amphiphilic multiblock copolymers and latexes. In this case, a water soluble macroagent of PAA previously synthetized was used in disperse media using a mixture of methanol/water (70:30, w/w). Stable latexes were obtained via polymerization‐induced self‐assembly and surface‐initiated polymerization of SSNa from alkoxyamine‐functionalized latex PAA‐b‐PS‐b‐PAA was also obtained © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 437–444 相似文献
18.
Angela Sobiesierski Robert Thomas Philip Buckle David Barrow Peter M. Smowton 《Surface and interface analysis : SIA》2015,47(13):1174-1179
The use of SU‐8 photoresist as a structuring material for portable capillary‐flow cytometry devices has been restricted by the near‐hydrophobic nature of the SU‐8 surface. In this work, we evaluate the use of chemical and plasma treatments to render the SU‐8 surface hydrophilic and characterise the resulting surface utilising a combination of techniques including contact angle goniometry, atomic force microscopy and X‐ray photoelectron spectroscopy. In particular, for low‐power plasma treatments, we find that the chemistry of the plasma used to modify the SU‐8 surface and the incorporation of O2 on that modified surface are paramount for improved surface wettability, whilst plasma‐induced surface roughness is not a necessary requirement. We demonstrate a technique to obtain a hydrophilic SU‐8 surface with contact angle as low as 7° whilst controlling and significantly reducing the level of surface roughness generated via the applied plasma. An additional chemical treatment step is found to be essential to stabilise the activated SU‐8 surface, and incubation of the samples with ethanolamine is demonstrated as an effective second‐stage treatment. Application of the optimised two‐stage surface treatment to cross‐linked SU‐8 is shown to result in a smooth hydrophilic surface that remains stable for over 3 months. Copyright © 2015 The Authors Surface and Interface Analysis Published by John Wiley & Sons Ltd. 相似文献
19.
Mesoporous molecular sieve SBA‐15 and conventional silica gel were grafted with 3‐[2‐(diethylamino)ethylamino]propyl groups and used as supports for the preparation of deposited palladium catalysts, which were subsequently evaluated in Stille cross‐coupling reaction of aryl bromides. The highest conversions were achieved with the metal‐saturated catalyst resulting from the modified SBA‐15. Influence of various reaction parameters (solvent, additive, temperature, etc.) on the overall yield and selectivity was studied. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
20.
Kubra Eksiler Yoshito Andou Hidayah Ariffin Yoshihito Shirai 《Journal of polymer science. Part A, Polymer chemistry》2019,57(24):2575-2580
This study addresses the inherent issues surrounding surface modification methods of nanofibers and proposes an environmentally friendly and less toxic strategy for the surface modification of hydrophilic nanofiber. From the continuation of our previous work, which discussed the easy production of nanofiber (average size: 127 nm) from oil palm mesocarp fiber (OPMF), in this work, the surface of nanofibers (M‐IL‐OPMF) were modified through vapor‐phase‐assisted surface polymerization (VASP) to improve the affinity of interface between the polymer grafted M‐IL‐OPMF and non‐polar matrix. VASP of ε‐caprolactone was successfully proceeded from the [M‐IL‐OPMF] at 70 °C for 24 h and 72 h, and compositions were estimated to be 35.7% fiber/64.3% polymer and 27.8% fiber/72.2% polymer. To confirm the grafting of PCL, size‐exclusion chromatography (SEC) and Fourier transform infrared (FT‐IR) spectroscopy, thermogravimetry (TG), and dispersibility test in hydrophobic solvent were carried out. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2575–2580 相似文献